Search NASA⌕ Search

SEARCH · Search NASA

Results for “NACA”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1940

Full-Scale Tests of Several Propellers Equipped with Spinners, Cuffs, Airfoil and Round Shanks, and NACA 16-Series Sections, Special Report

Wind-tunnel tests of several propeller, cuff, and spinner combinations were conducted in the 20 foot propeller-research tunnel. Three propellers, which ranged in diameter from 8.4 to 11.25 feet, were tested at the front end of a streamline body incorporating spinners of two diameters. The tests covered a blade angle range from 20 deg to 65 deg. The effect of spinner diameter and propeller cuffs on the characteristics of one propeller was determined. Test were also conducted using a propeller which incorporated aerodynamically good shank sections and using one which incorporated the NACA 16 series sections for the outer 20 percent of the blades. Compressibility effects were not measured, owing to the low testing speeds. The results indicated that a conventional propeller was slightly more efficient when tested in conjunction with a 28 inch diameter spinner than with a 23 inch spinner, and that cuffs increased the efficiency as well as the power absorption characteristics. A propeller having good aerodynamic shanks was found to be definitely superior from the efficiency standpoint to a conventional round-shank propeller with or without cuffs; this propeller would probably be considered structurally impracticable, however. The propeller incorporating the NACA 16 series sections at the tims were found to have a slightly higher efficiency than a conventional propeller; the take-off characteristics appeared to be equally good. The effects noted above probably would be accentuated at helical speeds at which compressibility effects would enter.

Biermann, David↗
NASA NTRS1941

The Effect of Various Wing-Gun Installations on the Aerodynamic Characteristics of an Airplane Model Equipped with an NACA Low-Drag Wing, Special Report

An investigation was made in the NACA 19-foot pressure wind tunnel to determine the effect of various win-gun installation on the aerodynamic characteristics of a model with an NACA low-drag wing. Measurements were made of lift and drag over an angle-of-attack range and for several values of dynamic pressure on a four-tenths scale model of a high-speed airplane equipped with the low-drag wing and with various wing-gun installations. Two installations were tested: one in which the blast tube and part of the gun barrel protrude ahead of the wing and another in which the guns is mounted wholly within the wing. Two types of openings for the latter installation were tested. For each installation three simulated guns were mounted in each wing. The results are given in the form of nondimensional coefficients. The installations tested appear to have little effect on the maximum-lift coefficient of the model. However, the drag coefficient shows a definite change. The least adverse effect was obtained with the completely internal mounting and small nose entrance. The results indicate that a properly designed wing-gun installation will have very little adverse effect on the aerodynamic characteristics of the low-drag wing.

Muse, Thomas C.↗
NASA NTRS1941

Characteristics of NACA 4400R Series Rectangular and Tapered Airfoils, Including the Effect of Split Flaps

At the request of the Bureau of Aeronautics, Navy Department, tests were made in the variable-density wind tunnel of a tapered wing of 3-10-18 plan form and based on the NACA 4400R series sections. The wing was also tested with 0.2 chord spit flaps, deflected 60 deg span ratios of 0.3, 0.5, 0.7 and 1.0 respectively. In order to get data from which to calculate the characteristics of the flapped wing, the investigation was extended to include tests of the four rectangular airfoils of the NACA 4400R series (4409R, 4412R, 4415R, and 4418R) with full-span 0.2 chord, trailing edge split flaps deflected 60 deg.

Greenberg, Harry↗
NASA NTRS2012

Evaluation of Icing Scaling on Swept NACA 0012 Airfoil Models

Icing scaling tests in the NASA Glenn Icing Research Tunnel (IRT) were performed on swept wing models using existing recommended scaling methods that were originally developed for straight wing. Some needed modifications on the stagnation-point local collection efficiency (i.e., beta(sub 0) calculation and the corresponding convective heat transfer coefficient for swept NACA 0012 airfoil models have been studied and reported in 2009, and the correlations will be used in the current study. The reference tests used a 91.4-cm chord, 152.4-cm span, adjustable sweep airfoil model of NACA 0012 profile at velocities of 100 and 150 knot and MVD of 44 and 93 mm. Scale-to-reference model size ratio was 1:2.4. All tests were conducted at 0deg angle of attack (AoA) and 45deg sweep angle. Ice shape comparison results were presented for stagnation-point freezing fractions in the range of 0.4 to 1.0. Preliminary results showed that good scaling was achieved for the conditions test by using the modified scaling methods developed for swept wing icing.

Tsao, Jen-Ching↗
NASA NTRS1943

Wind-Tunnel Tests of an NACA 44R-Series Tapered Wing with a Straight Trailing Edge and a Constant-Chord Center Section

As part of a general investigation in the NACA 19-foot pressure tunnel to determine stall characteristics and effectiveness of high-lift devices on wings of various sections, tests were made of a tapered. wing having NACA 44R-series airfoil sections. Lift, drag, pitching-moment, and stall characteristics were determined at a Reynolds number of 4,850,000 for the plain wing and for the wing with partial-and with full-span split flaps. The stall progressed slowly over The plain wing; a gradual loss of lift for angles of attack up to and beyond that for the maximum lift coefficient resulted. As Compared with the stall of the plain wing, the initial stall of the wing with either partial-span or full-span flaps deflected occurred at a higher angle of attack and the stall progressed much more rapidly. The maximum lift coefficients at a Reynolds number of 4,850,000 were 1.35 for the plain wing, 2.25 for the wing with partial-span flaps at 60 deg, and 2.67 for the wing with full-span flaps at 60 deg. The positions of the aerodynamic center, in terms of mean chords back of the leading edge of the root section, were approximately 0.458 with no flaps, 0.483 with partial-span flaps at 60 deg, and 0.498 with full-span flaps at 60 deg.

Neely, Robert H.↗
NASA NTRS1949

Index of NACA Technical Publications: 1915-1949

The Index of NACA Technical Publications covers reports issued from the date of origin of the Committee in 1915 until approximately September 1949. Because omissions were noted after publication of the Index issued in 1947, and since many new reports have been released since that time, it was decided to issue a new volume to supersede completely the 1947 Index, with supplements to be issued regularly in the future. Commencing with all publications issued after September 1, 1949, subject classifications were revised, the most important change involving the transfer of aircraft loads reports from the Aerodynamics classification to Structures. For those maintaining a file of NACA index cards, it is recommended that cards issued for reports dated prior to September 1, 1949 be removed from the file. This volume includes the same index information. Supplements covering periods following September 1, 1949, will be arranged according to the revised subject classifications. On the pages immediately following, the subject classifications are indexed in order of breakdown. There is included in the back of this volume an alphabetical arrangement of the subject classifications.

Source record↗
NASA NTRS1949

Index of NACA Technical Publications: 1915-1949

The Index of NACA Technical Publications covers reports issued from the date of origin of the Committee in 1915 until approximately September 1949. Because omissions were noted after publication of the Index issued in 1947, and since many new reports have been released since that time, it was decided to issue a new volume to supersede completely the 1947 Index, with supplements to be issued regularly in the future. Commencing with all publications issued after September 1, 1949, subject classifications were revised, the most important change involving the transfer of aircraft loads reports from the Aerodynamics classification to Structures. For those maintaining a file of NACA index cards, it is recommended that cards issued for reports dated prior to September 1, 1949 be removed from the file. This volume includes the same index information. Supplements covering periods following September 1, 1949, will be arranged according to the revised subject classifications. On the pages immediately following, the subject classifications are indexed in order of breakdown. There is included in the back of this volume an alphabetical arrangement of the subject classifications.

Source record↗
NASA NTRS1942

Investigation of a Low-Drag Gun Port in the NACA Two-Dimensional Low-Turbulence Tunnel

Tests were made in the NACA two-dimensional low-turbulence tunnel of three gun ports with a height of approximately 4 percent of the chord faired into an NACA 66,2-213 low-drag-airfoil section by bulging the section at the gun port. Gun ports faired in this manner had practically no effect on the maximum lift and the critical compressibility speed of the section and showed only small increase in the drag in the range of lift coefficients for high-speed and cruising-flight conditions.

Horton, Elmer A.↗
NASA NTRS1946

Effect of Compressibility on the Pressure and Forces Acting on a Modified NACA 65,3-019 Airfoil Having A 0.20-Chord Flap

An investigation has been conducted in the Langley rectangular high-speed tunnel to determine the effect of compressibility on the pressure distribution for a modified NACA 65,3-019 airfoil having a 0.20-chord flap. The investigation was made for an angle-of-attack range extending from -2 to 12 deg at .20 flap deflections from 0 to -12 deg. Test data were obtained for Mach numbers from 0.28 to approximately 0.74. The results show that the effectiveness of the trailing-edge-type control surface rapidly decreased and approached zero as the Mach number increased above the critical value.

AIRFOILS-NACA 65,3-019 (MOD )-MOMENTS & ORDINATES ↗
NASA NTRS1944

Cooling Characteristics of a Pratt and Whitney R-2800 Engine Installed in an NACA Short-nose High-inlet-velocity Cowling

An investigation was made of the cooling characteristics of a P and W R-2800 engine with NACA short-nose high inlet-velocity cowling. The internal aerodynamics of the cowling were studied for ranges of propeller-advance ratio and inlet-velocity ratio obtained by deflection of cowling flaps. Tests included variations of engine power, fuel/air ratio and cooling-air pressure drop. Engine cooling data are presented in the form of cooling correlation curves, and an example for calculation of cooling requirements in flight is included.

HIGH-INLET-VELOCITY (SHORT-NOSE)↗
NASA NTRS1947

Experimental and Calculated Characteristics of Several NACA 44-series Wings with Aspect Ratios of 8, 10, and 12 and Taper Ratios of 2.5 and 3.5

The aerodynamic characteristics of seven unswept tapered wings were determined by calculation from two-dimensional data and by wind-tunnel tests in order to demonstrate the accuracy of the calculations and to show some of the effects of aspect ratio, taper ratio, and root thickness-chord ratio. The characteristics were calculated by the usual application of the lifting-line theory which assumes linear section lift curves and also by an application of the theory which allows the use of nonlinear lift curves. A correction to the lift for the effect of chord was made by using the Jones edge-velocity factor. The wings had aspect ratios of 8, 10, and 12, taper ratios of 2.5 and 3.5, and NACA 44-series airfoils.

WINGS, TAPERED - CHARACTERISTICS↗
NASA NTRS1941

Determination of control-surface characteristics from NACA plain-flap and tab data

The data from previous NACA pressure-distribution investigations of plain flaps and tabs have been analyzed and are presented in this paper in a form readily applicable to the problems of control-surface design. The experimentally determined variation of aerodynamic parameters with flap chord and tab chord are given in chart form and comparisons are made with the theory. With the aid of these charts and the theoretical relationships for a thin airfoil, the aerodynamic characteristics for control surfaces of any plan form with plain flaps and tabs may be determined. A discussion of the basic equations of the thin-airfoil theory and the development of a number of additional equations that will be helpful in tail design are presented in the appendixes. The procedure for applying the data is described and a sample problem of tail design is included. The data presented and the method of application set forth in this report should provide a reasonably accurate and satisfactory means of computing the aerodynamic characteristics of control surfaces.

TAIL SURFACES, HORIZONTAL - CHAR↗
NASA NTRS1941

Development of Cowling for Long-nose Air-cooled Engine in the NACA Full-scale Wind Tunnel

An investigation of cowlings for long-nose radial engines was made on the Curtiss XP-42 fighter in the NACA full-scale wind tunnel. The unsatisfactory aerodynamic characteristics of all the cowlings with scoop inlets tested led to the development of the annular high-velocity inlet cowlings. Tests showed that ratio of cooling-air velocity at cowling inlet to stream velocity should not be less than 0.5 for this type of cowling and that critical compressibility speed can be extended to more than 500 mph at 20,000 ft altitude.

AIR FLOW-ENGINE COWLINGS↗
NASA NTRS1946

An Experimental Investigation of Flow Conditions in the Vicinity of an NACA D(sub S)-type Cowling

Data are presented of the flow conditions in the vicinity of an NACA D sub S -type cowling. Tests were made of a 1/2 scale-nacelle model at inlet-velocity ratios ranging from 0.23 to 1.02 and angles of attack from 6 deg to 10 deg. The velocity and direction of flow in the vertical plane of symmetry of the cowling were determined from orifices and tufts installed on a board aligned with the flow. Diagrams showing velocity ratio contours and lines of constant flow angles are given.

FLAPPED↗
DOE OSTI2020

Materials Data on NaCa(PO3)3 by Materials Project

NaCa(PO3)3 crystallizes in the triclinic P-1 space group. The structure is three-dimensional. Na1+ is bonded in a 6-coordinate geometry to six O2- atoms. There are a spread of Na–O bond distances ranging from 2.29–2.72 Å. Ca2+ is bonded in a 8-coordinate geometry to eight O2- atoms. There are a spread of Ca–O bond distances ranging from 2.35–2.75 Å. There are three inequivalent P5+ sites. In the first P5+ site, P5+ is bonded to four O2- atoms to form corner-sharing PO4 tetrahedra. There are a spread of P–O bond distances ranging from 1.50–1.61 Å. In the second P5+ site, P5+ is bonded to four O2- atoms to form corner-sharing PO4 tetrahedra. There is two shorter (1.50 Å) and two longer (1.62 Å) P–O bond length. In the third P5+ site, P5+ is bonded to four O2- atoms to form corner-sharing PO4 tetrahedra. There are a spread of P–O bond distances ranging from 1.49–1.62 Å. There are nine inequivalent O2- sites. In the first O2- site, O2- is bonded in a 1-coordinate geometry to two equivalent Ca2+ and one P5+ atom. In the second O2- site, O2- is bonded in a bent 150 degrees geometry to two P5+ atoms. In the third O2- site, O2- is bonded in a distorted single-bond geometry to one Na1+, two equivalent Ca2+, and one P5+ atom. In the fourth O2- site, O2- is bonded in a bent 120 degrees geometry to two P5+ atoms. In the fifth O2- site, O2- is bonded in a 3-coordinate geometry to one Na1+, one Ca2+, and one P5+ atom. In the sixth O2- site, O2- is bonded in a 3-coordinate geometry to one Na1+, one Ca2+, and one P5+ atom. In the seventh O2- site, O2- is bonded in a distorted bent 150 degrees geometry to two P5+ atoms. In the eighth O2- site, O2- is bonded in a 1-coordinate geometry to two equivalent Na1+, one Ca2+, and one P5+ atom. In the ninth O2- site, O2- is bonded in a 1-coordinate geometry to one Na1+, one Ca2+, and one P5+ atom.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Materials Data on NaCa(PO2)3 by Materials Project

NaCa(PO2)3 crystallizes in the cubic P2_13 space group. The structure is three-dimensional. Na1+ is bonded to six O2- atoms to form NaO6 octahedra that share edges with three equivalent CaO6 octahedra. There are three shorter (2.50 Å) and three longer (2.53 Å) Na–O bond lengths. Ca2+ is bonded to six O2- atoms to form CaO6 octahedra that share edges with three equivalent NaO6 octahedra. All Ca–O bond lengths are 2.37 Å. P3+ is bonded in a bent 120 degrees geometry to two O2- atoms. Both P–O bond lengths are 1.53 Å. There are two inequivalent O2- sites. In the first O2- site, O2- is bonded in a distorted trigonal planar geometry to one Na1+, one Ca2+, and one P3+ atom. In the second O2- site, O2- is bonded in a distorted trigonal planar geometry to one Na1+, one Ca2+, and one P3+ atom.

36 MATERIALS SCIENCE↗
NASA NTRS1944

NACA Investigation of a Jet-Propulsion System Applicable to Flight

Following a brief history of the NACA investigation of jet-propulsion, a discussion is given of the general investigation and analyses leading to the construction of the jet-propulsion ground-test mock-up. The results of burning experiments and of test measurements designed to allow quantitative flight-performance predictions of the system are presented and correlated with calculations. These calculations are then used to determine the performance of the system on the ground and in the air at various speeds and altitudes under various burning conditions. The application of the system to an experimental airplane is described and some performance predictions for this airplane are made. It was found that the main fire could be restricted to an intense, small, and short annular blue flame burning steadily and under control in the intended combustion space. With these readily obtainable combustion conditions, the combustion chamber the nozzle walls and the surrounding structure could be maintained at normal temperatures. The system investigated was found to be capable of burning one-half the intake air up the fuel rates of 3 pounds per second. Calculations were shown to agree well with experiment. It was concluded that the basic features of the jet-propulsion system investigation in the ground-test mock-up were sufficiently developed to be considered applicable to flight installation. Calculations indicated that an airplane utilizing this jet-propulsion system would have unusual capabilities in the high-speed range above the speeds of conventional aircraft and would, in addition, have moderately long cruising ranges if only the engine were used.

DUCTS↗