Search NASA⌕ Search

SEARCH · Search NASA

Results for “OSCILLATION FREQUENCY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Stability Enhancement of Polymeric Sensing Films Using Fillers

Experiments have shown the stability enhancement of polymeric sensing films on mixing the polymer with colloidal filler particles (submicron-sized) of carbon black, silver, titanium dioxide, and fumed silicon dioxide. The polymer films are candidates for potential use as sensing media in micro/nano chemical sensor devices. The need for stability enhancement of polymer sensing films arises because such films have been found to exhibit unpredictable changes in sensing activity over time, which could result in a possible failure of the sensor device. The changes in the physical properties of a polymer sensing film caused by the sorption of a target molecule can be measured by any of several established transduction techniques: electrochemical, optical, calorimetric, or piezoelectric, for example. The transduction technique used in the current polymer stability experiments is based on piezoelectric principles using a quartz-crystal microbalance (QCM). The surface of the QCM is coated with the polymer, and the mass uptake by the polymer film causes a change in the oscillating frequency of the quartz crystal. The polymer used for the current study is ethyl cellulose. The polymer/ polymer composite solutions were prepared in 1,3 dioxolane solvent. The filler concentration was fixed at 10 weight percent for the composites. The polymer or polymer composite solutions were cast on the quartz crystal having a fundamental frequency of about 6 MHz. The coated crystal was subjected to a multistage drying process to remove all measurable traces of the solvent. In each experiment, the frequency of oscillation was measured while the QCM was exposed to clean, dry, flowing air for about 30 minutes, then to air containing a known concentration of isopropanol for about 30 minutes, then again to clean dry air for about 30 minutes, and so forth. This cycle of measurements for varying isopropanol concentrations was repeated at intervals for several months. The figure depicts some of the sensing film stability results for ethyl cellulose polymer, ethyl cellulose-carbon black, and ethyl cellulose-silicon dioxide composite systems. An ethyl cellulose film exhibited a marked decline in response in the first few months of study and settled to a steady average response after about four months. However, response varied widely around the average response for ethyl cellulose film. In contrast, ethyl cellulose- carbon black and ethyl cellulose-silicon dioxide composites also declined in the early months, but showed more repeatable sensing film activity after the initial decline. Similar trends were observed in experiments for ethyl cellulose-titanium dioxide and ethyl cellulose-silver composites.

Lin, Brian↗

The Aerodynamics of Axisymmetric Blunt Bodies Flying at Angle of Attack

The Mars Science Laboratory entry capsule is used as an example to demonstrate how a blunt body of revolution must be treated as asymmetric in some respects when flying at a non-zero trim angle of attack. A brief description of the axisymmetric moment equations are provided before solving a system of equations describing the lateral-directional moment equations for a blunt body trimming at an angle of attack. Simplifying assumptions are made which allow the solution to the equations to be rearranged to relate the roll and yaw stability with sideslip angle to the frequency of oscillation of the vehicle body rates. The equations show that for a blunt body the roll and yaw rates are in phase and proportional to each other. The ratio of the rates is determined by the static stability coefficients and mass properties about those axes. A trajectory simulation is used to validate the static yaw stability parameter identification equation and a simple method of identifying the oscillation frequency from the body rates. The approach is shown to successfully extract the modeled yaw stability coefficient along a simulated Mars entry in agreement with data earlier analysis of MSL flight data.

Schoenenberger, Mark↗

Apparatus and methods for determining at least one characteristic of a proximate environment

Methods and an apparatus for determining at least one characteristic of an environment are disclosed. A vibrational energy may be imparted into an environment and a magnitude of damping of the vibrational energy may be measured and at least one characteristic of the environment may be determined. Particularly, a vibratory source may be operated and coupled to an environment. At least one characteristic of the environment may be determined based on a shift in at least one steady-state frequency of oscillation of the vibratory source. An apparatus may include at least one vibratory source and a structure for positioning the at least one vibratory source proximate to an environment. Further, the apparatus may include an analysis device for determining at least one characteristic of the environment based at least partially upon shift in a steady-state oscillation frequency of the vibratory source for the given impetus.

47 OTHER INSTRUMENTATION↗

Evaluation of crystal oscillators and frequency dividers for high temperature operation

Active and passive components of crystal oscillators and frequency dividers were tested to determine their performance at temperatures from 300 C to 350 C. The properties of GaAs JFETs were determined and their performance compared with that of silicon devices. Techniques for constructing breadboard circuits were assessed for operation in this temperature range. A Pierce oscillator and a multivibrator (Colorado crystal) oscillator were constructed and tested. Device failures are discussed.

Source record↗

Current-driven ion-acoustic and potential-relaxation instabilities excited in plasma plume during electron beam welding

Many papers have sought correlations between the parameters of secondary particles generated above the beam/work piece interaction zone, dynamics of processes in the keyhole, and technological processes. Low- and high-frequency oscillations of the current, collected by plasma have been observed above the welding zone during electron beam welding. Low-frequency oscillations of secondary signals are related to capillary instabilities of the keyhole, however; the physical mechanisms responsible for the high-frequency oscillations (>10 kHz) of the collected current are not fully understood. This paper shows that peak frequencies in the spectra of the collected high-frequency signal are dependent on the reciprocal distance between the welding zone and collector electrode. From the relationship between current harmonics frequency and distance of the collector/welding zone, it can be estimated that the draft velocity of electrons or phase velocity of excited waves is about 1600 m/s. The dispersion relation with the properties of ion-acoustic waves is related to electron temperature 10 000 K, ion temperature 2 400 K and plasma density 10{sup 16} m{sup −3}, which is analogues to the parameters of potential-relaxation instabilities, observed in similar conditions. The estimated critical density of the transported current for creating the anomalous resistance state of plasma is of the order of 3 A·m{sup −2}, i.e. 8 mA for a 3–10 cm{sup 2} collector electrode. Thus, it is assumed that the observed high-frequency oscillations of the current collected by the positive collector electrode are caused by relaxation processes in the plasma plume above the welding zone, and not a direct demonstration of oscillations in the keyhole.

36 MATERIALS SCIENCE↗

Characteristics of cyclic heat release variability in the transition from spark ignition to HCCI in a gasoline engine

We study selected examples of previously published cyclic heat-release measurements from a single-cylinder gasoline engine as stepwise valve timing adjustments were made to shift from spark ignited (SI) combustion to homogeneous charge compression ignition (HCCI). Wavelet analysis of the time series, combined with conventional statistics and multifractal analysis, revealed previously undocumented features in the combustion variability as the shift occurred. In the spark-ignition combustion mode, the heat-release variations were very small in amplitude and exhibited more persistent low-frequency oscillations with intermittent high-frequency bursts. In the HCCI combustion mode, the amplitude of the heat-release variations again was small and involved mainly low-frequency oscillations. At intermediate states between SI and HCCI, a wide range of very large-amplitude oscillations occurred, including both persistent low-frequency periodicities and intermittent high-frequency bursts. It appears from these results that real-time wavelet decomposition of engine cylinder pressure measurements may be useful for on-board tracking of SI HCCI combustion regime shifts.

33 ADVANCED PROPULSION SYSTEMS↗

Forced Oscillation Grid Vulnerability Analysis and Mitigation Using Inverter-Based Resources: Texas Grid Case Study

Forced oscillation events have become a challenging problem with the increasing penetration of renewable and other inverter-based resources (IBRs), especially when the forced oscillation frequency coincides with the dominant natural oscillation frequency. A severe forced oscillation event can deteriorate power system dynamic stability, damage equipment, and limit power transfer capability. This paper proposes a two-dimension scanning forced oscillation grid vulnerability analysis method to identify areas/zones in the system that are critical to forced oscillation. These critical areas/zones can be further considered as effective actuator locations for the deployment of forced oscillation damping controllers. Additionally, active power modulation control through IBRs is also proposed to reduce the forced oscillation impact on the entire grid. The proposed methods are demonstrated through a case study on a synthetic Texas power system model. The simulation results demonstrate that the critical areas/zones of forced oscillation are related to the areas that highly participate in the natural oscillations and the proposed oscillation damping controller through IBRs can effectively reduce the forced oscillation impact in the entire system.

24 POWER TRANSMISSION AND DISTRIBUTION↗

HOW PECULIAR WAS THE RECENT EXTENDED MINIMUM: A HINT TOWARD DOUBLE MINIMA

In this paper, we address the controversy regarding the recent extended solar minimum as seen in helioseismic low- and intermediate-degree mode frequencies: studies from different instruments identify different epochs of seismic minima. Here we use mode frequencies from a network of six identical instruments, the Global Oscillation Network Group, continuously collecting data for more than 15 years, to investigate the epoch of minimum in solar oscillation frequencies prior to the beginning of solar cycle 24. We include both low- and intermediate-degree modes in the l range of 0-120 and frequency range of 2.0-3.5 mHz. In this analysis, we demonstrate that there were indeed two minima in oscillation frequencies, depending upon the degree of modes, or more precisely the lower turning point radius of the propagating wave. We also analyze frequencies as a function of latitude to identify the beginning of solar cycle 24. We observe two minima at high latitudes and a single minimum at mid/low latitudes. This scenario is in contrast to cycle 23 where the epoch of seismic minimum did not change with latitude or depth. Our results also hint at a possible role of the relic magnetic field in modifying the oscillation frequencies of modes sampling deeper layers.

79 ASTRONOMY AND ASTROPHYSICS↗

Fault Location Using the Natural Frequency of Oscillation of Current Discharge in MTdc Networks

This paper discusses a novel offline-fault location approach using single ended measurements. The natural dissipation of the circuit parameters are considered for fault location. A relationship between the damped natural frequency of oscillation of the transmission line current and fault location is established. The hybrid dc circuit breaker (dcCB) interrupts the fault current, whereby the transmission line current attenuates under the absence of any driving voltage source. The line capacitance discharges into the fault at a specific frequency of oscillation and rate of attenuation. Utilizing this information, the fault location in a multi-terminal direct current (MTdc) network can be obtained. A three terminal radial model of a MTdc is used for performance evaluation of the proposed method using Power System Computer Aided Design (PSCAD)/Electromagnetic Transients including dc (EMTdc).

42 ENGINEERING↗

Adaptive Narrowband Damping for Improving Harmonic Stability of Modular Multilevel Converter

Harmonic instability events between modular multilevel converter (MMC) and ac systems have been widely reported in recent years. To damp harmonic resonance, this paper proposes an adaptive narrowband damping control that automatically programs, adds, and adjusts the damping around the oscillation frequency when an oscillation is detected. First, the paper presents a low-pass filter design for MMC control loops that pushes all negative damping of the MMC impedance down to the medium-frequency range (< ~ 1000 Hz). Then, an adaptive damping control that uses online oscillation detection is proposed, which can automatically configure the narrowband damper to provide positive damping to the MMC around the detected oscillation frequency. In contrast to existing narrowband damping methods, the proposed adaptive narrowband damper dynamically adjusts the damping gain and the width of the damping range based on continuous monitoring of system resonance conditions (e.g., adjust damping gain to zero when the system resonance disappears). Electromagnetic transient simulation results validate the efficacy of the proposed method in two typical MMC-based power systems.

active damping↗

Global optimization of harmonic oscillator basis in covariant density functional theory

The present investigation focuses on the improvement of the accuracy of the description of binding energies within moderately sized fermionic basis. Using the solutions corresponding to infinite fermionic basis it was shown that in the case of meson exchange (ME) covariant energy density functionals (CEDFs) the global accuracy of the description of binding energies in the finite $N_F$ = 16 - 20 bases can be drastically (by a factor ranging from ~3 up to ~9 dependent on the functional and $N_F$) improved by a global optimization of oscillator frequency of the basis. This is a consequence of the unique feature of the ME functionals in which with increasing fermionic basis size fermionic and mesonic energies approach the exact (infinite basis) solution from above and below, respectively. As a consequence, an optimal oscillator frequency $\hbar\omega_0$ of the basis can be defined which provides an accurate reproduction of exact total binding energies by the ones calculated in truncated basis. This leads to a very high accuracy of the calculations in moderately sized $N_F=20$ basis when mass dependent oscillator frequency is used: global rms differences $\delta B_{rms}$ between the binding energies calculated in infinite and truncated bases are only 0.025 MeV and 0.031 MeV for the NL5(Z) and DD-MEZ functionals, respectively. Optimized values of the oscillator frequency $\hbar\omega_0$ are provided for three major classes of CEDFs, i.e. for density dependent meson exchange functionals, nonlinear meson exchange ones and point coupling functionals.

Binding energy & masses↗

Limits on coronal reflection using high-frequency solar oscillations

Acoustic waves in the Sun with frequencies above about 5.3 mHz can propagate in the chromosphere. We examine imaged solar intensity data for evidence of reflection of these waves in the upper chromosphere, where the temperature increases by a large factor over a short distance. Our method is to compare the observed and theoretically derived frequency spacings between peaks in the power spectrum. We find that our theoretical frequencies provide the best fit to the data when the reflection in the upper atmosphere is eliminated. In particular, the model of Kumar (1993b), which includes the source depth, and radiative damping, in the calculation of power spectra but ignores chromospheric reflection, gives peak frequencies that are in good agreement with the observations. For acoustic waves of frequency greater than 6 mHz we put an upper limit to the reflectivity of chromosphere and corona, using our method, of about 10%. At a given spherical harmonic degree, the frequency spacing between peaks in the data generally decreases with increasing frequency, because the lower turning point of the waves is moving inward. However, between 5 and 5.5 mHz the frequency spacing increases slightly. This feature is probably associated with the acoustic cutoff frequency in the solar atmosphere, i.e., it indicates a transition from trapped waves to propagating waves. We are able to reproduce the observed behavior by a crude modeling of the solar atmosphere. Further study of these peaks should provide an independent way of exploring the mean structure of the solar atmosphere, particularly around the temperature minimum region.

Kumar, P.↗

Mathematical Modeling on the Influence of Casting Parameters on Initial Solidification at the Meniscus of Slab Continuous Casting

In the current study, the two-dimensional mold model was applied to investigate the influence of different casting parameters on the initial solidification at the meniscus of the continuous casting mold. The profile of the meniscus and the slag rim, and the heat flux on the hot face of the copper plate, were compared with different locations of the mold and different casting parameters. The depth of the oscillation marks and solidified meniscus through simulation was measured with different casting parameters. With the mold oscillating downward from the peak to the valley, the maximum heat flux on the hot face of the copper plate near the meniscus increased from 4.3 to 5.5 MW/m{sup 2}, the thickness of the slag rim decreased from 4.7 to 4.2 mm, and the height of the curved meniscus also decreased. With the increase of casting speed from 1.2 to 1.45 m/min, the maximum speed of the upper backflow increased from 0.6 to 0.8 m/s, and the lowest location of the meniscus at approximately 310 mm from the copper plate decreased from 22 to 12 mm below the meniscus near the nozzle, where the slag entrapment easily occurred. With the increase of the casting speed, casting superheat, and oscillation frequency, and the decrease of the water flow rate in the mold and oscillation amplitude, the thickness of the slag rim decreased. With the increase of casting speed and superheat, and the decrease of the water flow rate in the mold, oscillation frequency, and oscillation amplitude, the depth of the solidified meniscus decreased. The regression equation was fitted to estimate the depth of hooks at the subsurface of slabs.

36 MATERIALS SCIENCE↗

A SEISMIC SIGNATURE OF A SECOND DYNAMO?

The Sun is a variable star whose magnetic activity varies most perceptibly on a timescale of approximately 11 years. However, significant variation is also observed on much shorter timescales. We observe a quasi-biennial (2 year) signal in the natural oscillation frequencies of the Sun. The oscillation frequencies are sensitive probes of the solar interior and so by studying them we can gain information about conditions beneath the solar surface. Our results strongly point to the 2 year signal being distinct and separate from, but nevertheless susceptible to the influence of, the main 11 year solar cycle.

79 ASTRONOMY AND ASTROPHYSICS↗

Measurements of high-frequency solar oscillation modes

The spatial-temporal spectrum of solar oscillations exhibits modelike structure at frequencies above the nominal photospheric acoustic cutoff of about 5.3 mHz. The linewidth and frequency of these features are measured as functions of degree from high-quality spectra obtained from observations made at the geographic South Pole. From 5.3 to 6.5 mHz the linewidths are relatively constant with a value of about 70 microHz, approximately one-half the frequency difference between modes of the same degree but successive values of radial order number. This width is larger than can be accounted for by simple considerations of the leakage of trapped acoustic waves. The frequencies of the high-frequency modes adhere to a simple dispersion law if one uses a substantially larger effective phase shift that applies at lower frequencies. The frequency variation of this phase shift changes markedly above the acoustic cutoff frequency.

Duvall, T. L., Jr.↗

Ambient-Frequency-Data Based System-Level Inertia Estimation Using Physical Equation and its Practice on Hawaii Islands

Here, in this paper, a practical ambient-frequency-data-based inertia estimation method using a physical equation is proposed and validated by real measurement data from Hawaii island grids. With high renewable penetration, accurate inertia estimation is important and urgent. Ambient frequency oscillation always exists in power grids, so the proposed method has advantages of real-time inertia estimation and no need for additional disturbances. This paper first developed the physical equation for inertia estimation to offer a clear mechanism for easy implementation in practice. To apply the proposed method in actual grids, a practical method to extract the ambient frequency oscillation from frequency measurement is further proposed. The inertia estimation using the physical equation is validated by KIUC simulation data and HECO field data, in which error rates are around 2% and 8%, respectively. Practical inertia estimation is challenging due to the large amounts of resources contributing to the power grid's effective inertia, but the method provided in this paper can offer a novel way for practical inertia estimation, which can help renewable penetration to boost carbon-free grid.

14 SOLAR ENERGY↗

A Multiagent Deep Reinforcement Learning-Enabled Dual-Branch Damping Controller for Multimode Oscillation

Here, this study develops a multiagent deep reinforcement learning (MADRL)-enabled framework for the decentralized cooperative control of a novel dual-branch (DB) damping controller for both low-frequency oscillation (LFO) and ultralow-frequency oscillation (ULFO). It has two branches, each of which consists of a proportional resonance (PR) and a second-order polynomial that is designed to handle target oscillation modes. To improve the robustness of the controller to system uncertainties, MADRL is developed, where multiagents are centrally trained to obtain the coordinated adaptive control policy while being executed in a decentralized manner to provide the optimal parameter setting for each controller with only local states. Comparisons with the IEEE 10-machine 39-bus system demonstrate that the proposed method achieves better robustness to uncertainties, lower communication delay, and single-point failure, as well as damping control performances for both LFO and ULFO.

97 MATHEMATICS AND COMPUTING↗

Identification of two mechanisms for current production in a biharmonic flashing electron ratchet

Ratchets rectify the motion of randomly moving particles, which are driven by isotropic sources of energy such as thermal and chemical energy, without applying a net, time-averaged force between source and drain. We describe the behavior of a damped electron, modeled by a quantum Lindblad master equation, within a flashing ratchet (a one-dimensional potential that oscillates between a flat surface and a periodic asymmetric surface). By investigating the complete space of all biharmonic potential shapes and a large range of oscillation frequencies, two modes of ratchet operation, differentiated by their oscillation frequencies (relative to the rate of electron relaxation), are identified. Slow-oscillating, strong friction ratchets operate by a classical, overdamped mechanism. In fast-oscillating, weak friction ratchets, current is primarily produced when the frequency of the oscillating potential is resonant with the beating of the electron wave function in the potential well. The shape of the ratchet potential determines the direction of the current (and, in some cases, straightforwardly accounts for current reversals), but the maximum achievable current at any shape is controlled by the degree of friction applied to the electron.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗