Search NASA⌕ Search

SEARCH · Search NASA

Results for “Optical measurement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Energy shift of Fe-K fluorescence lines due to low ionization demonstrated with XRISM in Centaurus X-3

The Fe K$\alpha$ fluorescence line at 6.4 keV is a powerful probe of cold matter surrounding X-ray sources and has been widely used in various astrophysical contexts. The X-ray microcalorimeter spectrometer onboard XRISM can measure line shifts with unprecedented precision of ${\sim }$0.2 eV, equivalent to a line-of-sight velocity of ${\sim }$10 km s$^{-1}$. At this level of accuracy, however, several factors that influence the line energy must be carefully considered prior to astrophysical interpretation. One such important factor is the ionization degree, Fe$^{q+}$. The K$\alpha$ line shifts redward by ${\sim }$4 eV as q increases from 0 (neutral) to 8 (Ar-like). Additionally, the accompanying Fe K$\beta$ line at 7.06 keV shifts blueward by ${\sim }$30 eV from $q=0$ to 8. We demonstrate that this effect is actually observable in the XRISM data of the high-mass X-ray binary Centaurus X-3 (Cen X-3). We advocate that the differential energy shift between the K$\alpha$ and K$\beta$ line provides a robust estimate of q by decoupling from other effects that shift the two lines in the same direction. We derived $q \sim 5$ (Sc-like) for the fluorescing matter by comparing the observation with atomic structure calculations of our own and in the literature. By accounting for the derived charge state and the corresponding shift in the rest-frame line energy, we made corrections for this effect and reached a consistent residual shift among the K$\alpha$, K$\beta$, and the optical measurement attributable to the systemic velocity of the system. Consequently, we obtained a new constraint on the location of the cold matter. This ionization effect needs to be assessed in all use cases of the Fe K$\alpha$ line shift beyond Cen X-3, and the proposed metric is generally applicable to all of them.

Astronomy and AstroPhysics↗

A Combined Computer Vision and Deep Learning Approach for Rapid Drone-Based Optical Characterization of Parabolic Troughs

Optical accuracy is a primary driver of parabolic trough concentrating solar power (CSP) plant performance, but can be damaged by wind loads, gravity, error during installation, and regular plant operation. Collecting and analyzing optical measurements over an entire operating parabolic trough plant is difficult, given the large scale of typical installations. Distant Observer, a software tool developed at the National Renewable Energy Laboratory, uses images of the absorber tube reflected in the collector mirror to measure both surface slope in the parabolic mirror and offset of the absorber tube from the ideal focal point. This technology has been adapted for fast data collection using low-cost commercial drones, but until recently still required substantial human labor to process large amounts of data. A new method leveraging advanced deep learning and computer vision tools can drastically reduce the time required to process images. This new method addresses the primary analysis bottleneck, identifying featureless, reflective mirror corner points to a high degree of accuracy. Recent work has shown promising results using computer vision methods. The combined deep learning and computer vision approach presented here proved highly effective and has the potential to further automate data collection and analysis, making the tool more robust. The method presented in this paper automatically identified 74.3% of mirror corners within 2 pixels of their manually marked counterparts and 91.9% within 3 pixels. This level of accuracy is sufficient for practical Distant Observer analysis within a target uncertainty. A commercial drone collected video of over 100 parabolic trough modules at an operating CSP plant to demonstrate the deep learning and computer vision method's usefulness in processing large amounts of data. These troughs were successfully analyzed using Distant Observer, paired with the new deep learning and computer vision algorithm, and can provide plant operators and trough designers with valuable insight about plant performance, operating strategies, and plant-wide optical error trends.

computer vision↗

Spectroscopy of GR1 centers in synthetic diamonds

We report on the spectroscopic characterization, absorption saturation, and excited-state dynamics of GR1 centers in synthetic diamonds. The non-linear optical measurements reveal an efficient bleaching of the GR1 center’s ground level under ns-pulsed 633 nm excitation. The maxima of absorption and emission cross sections were estimated to be 4.5 × 10 −17 cm 2 and 9 × 10 −17 cm 2 at 630 nm and 780 nm, respectively. The radiative lifetime of the excited level was estimated to be 8.5 ns. The 658 nm probe kinetics uncovered relaxation of 1 T 2 excited level going predominantly to a metastable state with a lifetime of 220 μs. An induced absorption detected with the use of a highly concentrated diamond sample could be due to up-conversion and photoionization processes in additional impurity-vacancy center with absorption at the short-wavelength tail of GR1. The results presented here indicate that synthetic diamonds with GR1 centers could serve as near infrared gain media or passive Q-switchers for laser cavities over the 633–750 nm spectral range. Optimization of the center concentration and the crystal parameters are required to minimize the induced absorption at the lasing wavelengths.

36 MATERIALS SCIENCE↗

Spin-glass state in nickelate superconductors

Magneto-optical measurements in La 0.8 Sr 0.2 NiO 2 and Nd 0.825 Sr 0.175 NiO 2 reveal an intriguing new facet of infinite-layer nickelate superconductors: the onset of spin-glass behavior at a temperature far exceeding the superconducting critical temperature T c . This discovery sharply contrasts with copper oxide superconductors, where magnetism and superconductivity remain largely exclusive. Moreover, the magnitude and onset temperature of the polar Kerr effect in Nd 0.825 Sr 0.175 NiO 2 fabricated on SrTiO 3 and (LaAlO 3 ) 0.3 (Sr 2 TaAlO 6 ) 0.7 substrates differ dramatically, while T c does not.

FOS: Physical sciences↗

Mechanochemistry of Phosphorus and Arsenic Alloys for Visible and Infrared Photonics

Incorporating few‐layer 2D phosphorus–arsenic alloys (PAs) into optoelectronic devices requires a synthesis technique that allows control of the alloy composition while producing volumes of material suitable for application development such as photodetectors, solar cells, and lasers. With that goal in mind, high‐energy ball milling allows production of both orthorhombic (o‐PAs) and trigonal (t‐PAs) alloys by reacting red phosphorus and metallic arsenic powders. The synthesis follows a two‐step process in which arsenic rapidly reacts with red phosphorus to first produce t‐PAs followed by a slower phase transformation into o‐PAs; synthesis time and overall conversion rate are slightly enhanced by the presence of arsenic. Optical measurements on exfoliated alloys at the few‐layer atomic limit of the 2D PAs reveal emission spanning from the visible (≈1.9 eV) into the near‐infrared region, covering a broad application space. Rapid powder synthesis within a closed system for stochiometric control of the solid‐solution PAs alloys combined with solution‐based exfoliation opens up opportunities for a whole new class of optoelectronic devices based on PA nanomaterials.

Pedersen, Samuel V.↗

Continuous Counter‐Current Microfluidic Liquid–Liquid Extraction Achieved Using a Pair of Wettable Screen Meshes

Continuous counter‐current microfluidic liquid–liquid extraction performs separations by flowing immiscible liquids in opposing directions within a single flow channel. In principle, this flow arrangement enables a large number of theoretical separation units in a small footprint, without using interstage valving, pumping, and phase separation. Despite its potential for excellent separation performance, this microfluidic scheme rarely appears in literature due to the requirement for capillary forces to be greater than hydrodynamic forces for stable flow. We present a novel microfluidic device and flow approaches that overcome this force‐balance challenge, enabling stable, long‐duration continuous counter‐current flow. Additionally, we cover a suite of methodologies for quantifying the performance of the microfluidic device, revealing the number of theoretical equilibrium stages achieved. The enabling technologies include a woven mesh screen‐based microfluidic device architecture that is easily fabricated outside of a clean room, surface functionalization strategies to promote conjugate (organic/aqueous) wettability, flow approaches to eliminate bubbles and carryover, and computer‐aided flow automation with optical measurement of extraction performance. The reported experiments lasted for over 36 h, terminated only at experiment conclusion, where the device still exhibited good performance. Automated Raman spectroscopy was used for solute quantitation of the ternary system tert‐butanol in a toluene/water matrix, a ternary system that was specifically chosen to analyze the device's performance with a small solute partition ratio and to enable in‐line Raman measurements of solute concentrations in both phases. The microfluidic device possessed a 55 mm contact length and a 38.5 µL internal volume. During counter‐current flow, we observed approximately 37 equilibrium stages (37 ± 13) based on a best‐fit of the solute fraction remaining in the aqueous phase using a Kremser Group Method analysis.

36 MATERIALS SCIENCE↗

Synthesis, Crystal Structure, and Physical Properties of BaSnS 2

Phase-pure BaSnS 2 , with space group P2 1 /c, is synthesized, and the structural and physical properties are investigated. We report thermal properties and optical measurements are reported for the first time. The Debye temperature and Sommerfeld coefficient are obtained from temperature-dependent heat capacity measurements, the latter indicating that BaSnS 2 is an electrical insulator. A direct bandgap of 2.4 eV is obtained from diffuse reflectance and photoluminescence spectroscopy. The findings herein lay the foundation for understanding the physical properties of this material and are part of a continuing effort to investigate previously unexplored ternary chalcogenides.

semiconductors↗

Synthesis, Crystal and Electronic Structure of La 2 SiP 4

La 2 SiP 4 (mP-28, Z=4, Wyckoff sequence e 7 , space group P2 1 /c (No. 14), a=10.8230(6) Å, b=7.5208(4) Å, c=7.9189(4) Å, and β=105.389(2)°) which crystallizes in the La 2 CuS 4 structure type is reported here. Instead of isolated CuS 3 triangles bridged by disulfide anions, in the crystal structure of La 2 SiP 4 , one-dimensional zig-zag chains composed of SiP 4 tetrahedra connected by P–P bonds are present. Lanthanum cations fill the voids between the chains and are coordinated by either 9P or 8P+Si atoms. La2SiP4 is a narrow bandgap semiconductor with calculated and measured optical bandgaps of 0.35 eV and 0.85(1) eV, respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Stereo-DIC Challenge 1.0 – Rigid Body Motion of a Complex Shape

Background Stereo-DIC is a widely used optical measurement technique that provides a dense full-field 3D measurement of the shape, displacement, and strain of a solid sample. When compared with 2D-DIC, Stereo-DIC provides greater flexibility and expands its use beyond flat, planar specimens. Furthermore, the widespread availability of commercial systems has led to the adoption of the technique throughout industry, academia, and government research labs. Objective Even though some research has been done to understand the effects of different experimental and stereo-DIC parameters, no reference is available to benchmark and compare the performance of current stereo-DIC algorithms to each other. Methods This paper provides the description and analysis of a carefully controlled 3D experiment and associated images used to compare the results from five subset based DIC software packages. Both the images and analysis codes used in this paper to compare the results are described here and are available for download and use for continued research. Results We show that over a very large range of motion, the 3D errors are very small, less than 80μm over a travel of ±20 mm out-of-plane and ±20 mm in-plane. While all codes performed similarly, there are important differences noted in the paper. Conclusion The image sets and results comparison software are hosted by the International DIC Society (www.iDICs.org) and are freely available for download and analysis for comparison with results in this paper. Furthermore, it is hoped that this set of images can be used for future research in improving stereo-DIC by future authors.

Algorithms comparison↗

Elucidating the effect of preheating temperature on melt pool morphology variation in Inconel 718 laser powder bed fusion via simulation and experiment

In laser powder bed fusion (L-PBF) additive manufacturing, the mechanical performance, microstructure and defects of fabricated parts are closely associated with the melt pool morphology, e.g., its dimension and shape through the building process. Past studies have largely focused on how the process parameters such as laser power and scan speed affect melt pool characteristics. In this study, the melt pool morphology variation as a function of preheating temperature in the conduction, transition, and keyhole regimes and the underlying mechanisms in each regime are investigated through ex-situ sample characterization and computation thermal fluid dynamics (CtFD) simulation. Single tracks with different combinations of laser power and scan speed are deposited on an Inconel 718 bare plate preheated to a temperature range of 100–500 °C in the experiment. Significant changes are observed in melt pool morphology as a function of preheating temperature from optical measurements of melt track cross sections. The depth of melt pool in the three regimes increases monotonically with preheating temperature, e.g., at 500 °C, the experimental melt pool depth is increased by 49% in conduction regime, 34% in transition regime and 33% in keyhole regime, respectively, while the variation of melt pool width in each regime does not all follow an increasing trend but depends on the melt pool regimes. Melt pool width variation in the conduction and transition regimes is found to depend on the enhanced heat conduction directly related to temperature dependent thermal properties. Through validated CtFD simulations, it is found that in the keyhole regime the evaporation mass, recoil pressure, and laser drilling effect is enhanced with higher preheating temperature, which gives rise to a deeper melt pool. The simulations also reveal that preheating temperature significantly elongates the melt track length due to the increased flow rate and strong recoil pressure that accelerates the backward flow.

36 MATERIALS SCIENCE↗

Predicting critical heat flux using localized sensing at invisible vapor-liquid interfaces

Predicting critical heat flux (CHF) in two-phase electronics cooling systems remains a significant challenge due to the sudden onset of boiling crisis and the difficulty in directly visualizing vapor-liquid interfaces. Existing sensing methods rely on lagging temperature measurements, optically accessible systems, or spatially averaged signals that cannot pinpoint CHF initiation at localized high-heat-flux regions. Here, we report a planar capacitive sensing approach that enables real-time, localized detection of vapor-liquid interface dynamics for CHF prediction in boiling heat transfer. The capacitive sensor exploits the dielectric constant difference between liquid and vapor phases to capture bubble nucleation, growth, and departure dynamics with a temporal resolution down to 2 ms. The capacitive sensing reveals distinct signals across boiling regimes: from high-frequency fluctuations during strong nucleate boiling to low-frequency fluctuations with increased amplitudes when approaching CHF. The multi-sensor array experiments demonstrate real-time localized sensing, where each sensor responds exclusively to boiling in its immediate vicinity without crosstalk from neighboring regions. This non-intrusive sensing approach provides predictive rather than lagging sensing signals of CHF occurrence, offering predictive diagnosis of two-phase liquid cooling for the thermal management of high-power-density electronics.

CHF↗

Formation of functionally graded steel by laser powder bed fusion via in-situ carbon doping

Additive Manufacturing (AM) enables functional integration by combining multiple components into a single part to shorten assembly time, reduce weight, and improve performance. Laser Powder Bed Fusion (LPBF) is an important AM method due to excellent spatial resolution, surface finish, and material properties without the need for extensive post-processing. Functional integration could be enhanced by spatial tuning of properties, but LPBF cannot readily vary material composition. Here, this paper addresses a method to add spatial composition control by printing small quantities of dopants via liquid carrier prior to laser fusion. The impact of carbon black suspension added to select regions of a Stainless Steel 316 L powder bed on melt pool dimension, hardness, and porosity is reported. The distribution of the carbon between the doped and plain layers and the resulting spatial variation in hardness is measured. Optical microscopy and composition analysis show that the carbon dispersed uniformly within the layer of deposition and diffused as little as 50 μm in the build direction. Keyhole conditions dramatically increase the inter-layer transport of the dopant. The added carbon increased hardness by >50 %. Porosity increased in doped regions but remained below 1.5 % for the best processing parameters. These results demonstrate that the composition of LPBF parts could be controlled in 3-dimensions using a dopant that is soluble in the melt pool. Additional work will be required to evaluate different dopant materials and optimize processing conditions for full density, but microalloying with soluble dopants appears to be a plausible solution to enhance functional integration with LPBF.

36 MATERIALS SCIENCE↗

Structural, magnetic, optical, dielectric and electronic properties of R 2 NiIrO 6 (R = Pr and Nd): A comprehensive experimental and theoretical investigation

Double perovskites are highly promising materials capable of exhibiting a wide variety of phenomena. In this work, we perform a comprehensive experimental and theoretical study of polycrystalline R 2 NiIrO 6 (R = Pr and Nd) compounds. Both compounds were synthesised using the solid-state reaction method. Rietveld refinement confirmed a monoclinic structure with the P2 1 /n space group for both compounds. The scanning electron images showed the average grain sizes of 0.55 μm for R = Pr and 0.46 μm for R = Nd. Fourier transform infrared ra- diation spectra of the two compounds presented two intense bands at 470 cm -1 and 540 cm -1 . The optical measurements revealed that the band gaps of the compounds were in the visible absorption range. The field- cooled magnetisation - field hysteresis measurements indicated exchange bias properties in the synthesised compounds at low temperatures. Both temperature and frequency variation of dielectric constant and loss tangent measurements were conducted. The frequency-dependent ac conductivity measurements indicated that the conductivity increases with the increase of frequency as well as temperature. The Nd 2 NiIrO 6 compound showed lower ac conductivities compared to its isostructural Pr 2 NiIrO 6 compound. The atomic and electronic structures of Nd 2 NiIrO 6 and Pr 2 NiIrO 6 were explored using the spin-polarised calculations performed within the DFT+U method. Our results suggested that the inclusion of on-site correlations and repulsions for the d-states of atoms was necessary in order to obtain finite band gaps of Nd 2 NiIrO 6 and Pr 2 NiIrO 6 systems.

36 MATERIALS SCIENCE↗

Development of a coupled experimental–computational approach for engineering optimization of spout-fluidized bed particle coating systems

The design of spout-fluidized bed (SFB) coating systems for nuclear particle fuels typically relies on trial-and-error processes, comprising iterative and time-consuming coating deposition experiments and post-deposition characterization. At an engineering scale, this approach to guided SFB system design is inefficient, highlighting the need for streamlined experimental methodologies which can correlate fluidization conditions to downstream coating outcomes. In this study, we combine time-resolved particle image velocimetry (PIV) with CFD–DEM simulations to benchmark hydrodynamic behavior in a 3D spout-fluidized bed. By exploiting easily accessible optical measurements of particle motion at the bed wall and within the spouting region, we obtain quantitative velocity fields that can be directly compared with model predictions of the occluded bed region, without resorting to complex imaging and characterization techniques such as X-ray or magnetic resonance tomography. Experimental benchmarking reveals strong agreement between CFD–DEM and PIV in the spout and annulus regions, while discrepancies near the wall highlight areas for future model development. Here, the proposed integrated experimental–numerical framework will enable a direct connection between measured variables and numerically predicted fluidization performance of dense, surrogate nuclear particle fuel feedstock such that experimental SFB component design can be rapidly evaluated, informing design decisions for nozzle geometry and operating conditions. Future work will extend this framework by correlating quantified fluidization metrics across nozzle geometries and operating conditions with the resulting coating morphology, microstructure, and uniformity. Establishing these correlations will enable predictive links between hydrodynamic performance and coating quality, providing a rational, scalable basis for optimizing SFB design prior to coating deposition.

CFD/DEM↗

Validation of the single-event method for low-energy electron transport via stopping power calculations with $\mathrm{MCNP}$

Monte Carlo simulations of low-energy ( <50 keV) electron transport in matter are essential for a broad range of application fields. Several Monte Carlo codes have developed specialized treatments for this case, but a comprehensive validation of low-energy electron transport for general-purpose simulations remains lacking in the literature. One approach to accomplish this validation is calculation of stopping power using low-energy electron transport physics, as stopping power is a fundamental radiation transport quantity which must be simulated accurately for nearly any application. Here in this work, we use the Monte Carlo N-Particle (MCNP) radiation transport code with the single-event method for electron transport to calculate stopping powers of low-energy electrons (50 eV to 30 keV) in 41 elemental solids, 14 compound solids, and five rare gas solids, comparing simulation results to published semi-empirical stopping power calculations from optical measurements. In general, the simulations give good agreement (typically within ±10%) with semi-empirical stopping power values at higher energies: 300 eV and above for most elemental solids, 1 keV and above for compound solids, and 400 eV and above for rare gas solids. Agreement between MCNP and semi-empirical values is worse below these energies. The most significant source of error is the EPRDATA14 cross section data, which does not account for changes in electronic structure due to solid-state bonding, particularly in compound materials. The simplistic model of atomic excitation used to generate the EPRDATA14 cross sections is another key source of error. Additionally, the breakdown of the continuous slowing-down approximation introduces significant uncertainty at low energies, although this is a limitation of the calculation method and not of the simulation procedure. Accounting for these and other uncertainty sources, the single event method in MCNP is robust and able to give good accuracy for a variety of low-energy electron transport problems through diverse kinds of materials.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Squeezing Noise in Microscopy with Quantum Light

Quantum-enhanced microscopes capable of probing classically inaccessible material properties have drawn increasing interest, but most proof-of-principle quantum microscopes have not surpassed classical limits. Here, we discuss the promise and obstacles associated with the use of quantum light with reduced noise (‘squeezed’ light) for quantum-enhanced atomic force microscopy, bioimaging, magneto-optical measurements, and Raman spectroscopy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Protocol to detect dilution cycles in chemostat experiments and estimate growth rate slopes with linear modeling with R software chemostat_regression

Chemostat growth chambers measure optical density over time and require manual calculation of growth rates. Here, we present chemostat_regression, R software that enables users to automatically identify chemostat cycles and estimate growth rate using a linear regression approach. We describe steps for creating requisite software environment(s), formatting input data, executing the software via command line/RStudio/R-Shiny, interpreting results, assessing the validity of results, and modifying input parameters.

59 BASIC BIOLOGICAL SCIENCES↗

Homologous Alkali Metal Copper Rare-Earth Chalcogenides A 2 Cu 2 n Ln 4 Q 7+ n ( n = 1, 2, 3)

Twenty-seven new members of the A 2 Cu 2n Ln 4 Q 7+n (A = Cs, Rb; Ln = La-Nd, Sm, Gd-Yb; Q = S, Se) homologous series were synthesized in one of three structural types (indicated by n = 1, 2, 3). All the compounds contained 3D frameworks with alkali-metal-containing tunnels. For each increment in n, one Cu 2 Q was added, which was incorporated into the framework as an edge-sharing tetrahedron by replacing a square planar chalcogenide site. High-throughput DFT calculations predicted many of the phases to be thermodynamically stable. These predictions were compared with the synthesis results for the phases formed in each composition space. In the syntheses, heavier lanthanides showed a preference to start forming the n = 3 ACu 3 Ln 2 Q 5 , which is consistent with the predictions. RbCuNd 2 Se 4 and RbCuTb 2 Se 4 were found to be thermally stable under vacuum at temperatures up to 1000 °C. Optical measurements revealed band gaps of 1.55(5) and 1.62(5) eV for CsCuCe 2 Se 4 and RbCuTb 2 Se 4 , respectively, and a work function of 4.83(5) eV for CsCuPr 2 Se 4 . Additionally, some n = 3 ACu 3 Ln 2 Qs compounds exhibit a negative phonon mode because of a copper atom coordination, which may distort to a trigonal planar geometry at sufficiently low temperatures. The dynamic instabilities and the predicted distortion in the copper tetrahedra for the n = 3 ACu 3 Ln 2 Q 5 compounds were found to have a linear relationship with the atomic number of the lanthanides and the electronegativity of the lanthanides. In conclusion, the A 2 Cu 2 n Ln 4 Q 7+n compounds can potentially find application as high-temperature thermoelectric materials and other semiconductors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗