Search NASA⌕ Search

SEARCH · Search NASA

Results for “PITCHING MOMENTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Performance of an aero-space plane propulsion nozzle

An inviscid and viscous analysis is provided for an exposed half nozzle that is used with a scramjet for thrust generation. The analysis is based on the inviscid theory of a two-dimensional, minimum length nozzle with a curved inlet surface, where the flow may be sonic or supersonic. Inlet conditions are prescribed and the gas is assumed to be perfect. Viscous, and when appropriate inviscid, nondimensional parametric results are provided for the thrust, lift, heat transfer, pitching moment, and a variety of boundary-layer thicknesses. In addition to global results, wall distributions of pressure, heat transfer, etc., are provided. The analysis demonstrates that the nozzle produces a considerable lift force whose magnitude may exceed the thrust and a significant pitching moment. The thrust is quite sensitive to the inlet Mach number; it rapidly decreases as the inlet Mach number increases There is little loss in the thrust as the nozzle's downstream wall is truncated. The corresponding decrease in lift and the pitching moment is moderate.

Emanuel, George↗
NASA NTRS1931

Experimental Determination of Jet Boundary Corrections for Airfoil Tests in Four Open Wind Tunnel Jets of Different Shapes

This experimental investigation was conducted primarily for the purpose of obtaining a method of correcting to free air conditions the results of airfoil force tests in four open wind tunnel jets of different shapes. Tests were also made to determine whether the jet boundaries had any appreciable effect on the pitching moments of a complete airplane model. Satisfactory corrections for the effect of the boundaries of the various jets were obtained for all the airfoils tested, the span of the largest being 0.75 of the jet width. The corrections for angle of attack were, in general, larger than those for drag. The boundaries had no appreciable effect on the pitching moments of either the airfoils or the complete airplane model. Increasing turbulence appeared to increase the minimum drag and maximum lift and to decrease the pitching moment.

Knight, Montgomery↗
NASA NTRS1949

Wind-Tunnel Investigation of the Low-Speed Static Stability and Control Characteristics of a Model of the Bell MX-776 (RASCAL) in Combined Angle of Attack and Sideslip

An investigation has been made in the Langley stability tunnel to determine the low-speed static stability and control characteristics of a model of the Bell MX-776. The results show the model to be longitudinally unstable in the angle-of-attack range around zero angle of attack and to become stable at moderate angles of attack. The results of the present investigation agree reasonably well with results obtained in other facilities at low speed. The present pitching-moment results at low Mach numbers also agree reasonably well with unpublished results of tests of the model at supersonic Mach numbers (up to Mach number 1.86). Unpublished results at moderate and high subsonic speeds, however, indicate considerably greater instability at low angles of attack than is indicated by low-speed results. The results of the present tests also showed that the pitching-moment coefficients for angles of attack up to 12deg remained fairly constant with sideslip angle up to 12deg. The elevators tested produced relatively large pitching moments at zero angle of attack but, as the angle of attack was increased, the elevator effectiveness decreased. The rate of decrease of elevator effectiveness with angle of attack was less for 8deg than for 20deg elevator deflection. Therefore although 8deg deflection caused an appreciable change in longitudinal trim angle and trim lift coefficient a deflection of 20deg caused only a small additional increase in trim angle and trim lift coefficient.

Letko, William↗
NASA NTRS2016

Helicopter Non-Unique Trim Strategies for Blade-Vortex Interaction (BVI) Noise Reduction

An acoustics parametric analysis of the effect of fuselage drag and pitching moment on the Blade-Vortex Interaction (BVI) noise radiated by a medium lift helicopter (S-70UH-60) in a descending flight condition was conducted. The comprehensive analysis CAMRAD II was used for the calculation of vehicle trim, wake geometry and integrated air loads on the blade. The acoustics prediction code PSU-WOPWOP was used for calculating acoustic pressure signatures for a hemispherical grid centered at the hub. This paper revisits the concept of the X-force controller for BVI noise reduction, and investigates its effectiveness on an S-70 helicopter. The analysis showed that further BVI noise reductions were achievable by controlling the fuselage pitching moment. Reductions in excess of 6 dB of the peak BVI noise radiated towards the ground were demonstrated by compounding the effect of airframe drag and pitching moment simultaneously.

Noise Reduction↗
NASA NTRS1941

Wind-tunnel investigation of an NACA 23012 airfoil with several arrangements of slotted flaps with extended lips

An investigation was made in the NACA 7- by 10-foot wind tunnel to determine the effect of slot-lip location on the aerodynamic section characteristics of an NACA 23012 airfoil with a 30-percent-chord slotted flap. Tests were made with slot lips located at 90 and 100 percent of the airfoil chord and with two different flap shapes. The results are compared with a slotted flap previously developed by the National advisory Committee for Aeronautics with a slot lip located at 83 percent of the airfoil chord. The extension of the slot lip to the rear increased the section lift and pitching-moment coefficients. Comparisons made on a basis of pitching moment for a given tail length show that the Fowler type flap, lip extended to trailing edge of the airfoil, has the greatest section lift coefficient. For moderate tail lengths, 2 to 3 chord lengths, there was only a slight difference between the previously developed slotted flap and the slotted flap with slot lip extended to 90 percent of the airfoil chord. Of the three flaps tested, the Fowler flap had the lowest drag coefficient at high lift coefficients. The extension of the lower surface at the leading edge of the slot had a negligible effect on the profile drag of the airfoil-flap arrangement with the flap deflected when the lip terminated at 90 percent of the airfoil chord.

WING FLAPS, SLOTTED - FULL-SPAN(30%-CHORD)↗
NASA NTRS1951

Theoretical characteristics of two-dimensional supersonic control surfaces

The "Busemann second-order-approximation theory" for the pressure distribution over a two-dimensional airfoil in supersonic flow was used to determine some of the aerodynamic characteristics of uncambered symmetrical parabolic and double-wedge airfoils with leading-edge and trailing-edge flaps. The characteristics presented and discussed in this paper are: flap effectiveness factor, rate of change of hinge-moment coefficient with flap deflection, rate of change of the pitching-moment coefficient with flap deflection, rate of change of the pitching-moment coefficient about the mid chord with flap deflection, and the location of the center of pressure of the airfoil-flap combination.

MACH NUMBER EFFECTS - WING SECTIONS↗
NASA NTRS1982

Identification of aerodynamic indicial functions using flight data

It is pointed out that the use of indicial function representation provides a model superior to the aerodynamic derivative model. Specific derivatives can be approximated from the indicial models. The model can also be used to compute equivalent stability and control parameters not usually available from flight data. It is shown that derivatives regarding the angle-of-attack and the side slip angle can be derived directly from the indicial functions without any identifiability problem. Attention is given to the pitch moment coefficient, linear indicial function representation, the identification problem for the pitch moment equation, the identifiability of linear systems, parametric representations of the indicial functions, an identification technique, angle-of-attack and pitch rate dynamics in the pitch plane, multivariate linear models, nonlinear aerodynamic indicial functions, measurement system accuracy, and poststall and spin-entry data from a scaled research vehicle.

Gupta, N. K.↗
NASA NTRS1987

Summary of studies to reduce wing-mounted propfan installation drag on an M = 0.8 transport

Powerplant installation losses for an advanced, high-speed, turboprop transport have been investigated in the Ames Research Center Transonic Wind Tunnels as a part of the NASA Advanced Turboprop Program (ATP). Force and pressure tests have been completed at Mach numbers from 0.6 to 0.82 on baseline and modified powered-model configurations to determine the magnitude of the losses and to what extent current design tools could be used to optimize the installed performance of turboprop propulsion systems designed to cruise at M = 0.8. Results of the tests indicate a large reduction in installed drag for the modified configuration. The wing-mounted power plant caused destabilizing pitching moments and a negative shift in the zero-lift pitching moment.

Smith, Ronald C.↗
NASA NTRS1989

Summary of longitudinal stability and control parameters as determined from Space Shuttle Challenger flight test data

Estimates of longitudinal stability and control parameters for the space shuttle were determined by applying a maximum likelihood parameter estimation technique to Challenger flight test data. The parameters for pitching moment coefficient, C(m sub alpha), (at different angles of attack), pitching moment coefficient, C(m sub delta e), (at different elevator deflections) and the normal force coefficient, C(z sub alpha), (at different angles of attack) describe 90 percent of the response to longitudinal inputs during Space Shuttle Challenger flights with C(m sub delta e) being the dominant parameter. The values of C(z sub alpha) were found to be input dependent for these tests. However, when C(z sub alpha) was set at preflight predictions, the values determined for C(m sub delta e) changed less than 10 percent from the values obtained when C(z sub alpha) was estimated as well. The preflight predictions for C(z sub alpha) and C(m sub alpha) are acceptable values, while the values of C(z sub delta e) should be about 30 percent less negative than the preflight predictions near Mach 1, and 10 percent less negative, otherwise.

Suit, William T.↗
NASA NTRS1996

Aerodynamic Limitations of the UH-60A Rotor

High quality airloads data have been obtained on an instrumented UH-60A in flight and these data provide insight into the aerodynamic limiting behavior of the rotor. At moderate weight coefficients and high advance ratio limiting performance is largely caused by high drag near the blade tip on the advancing side of the rotor as supercritical flow develops on the rotor with moderate to strong, shocks on both surfaces of the blade. Drag divergence data from two-dimensional airfoil tests show good agreement with the development of the supercritical flow regions. Large aerodynamic pitching moments are observed at high advance ratio, as well, and these pitching moments are the source of high torsional moments on the blade and control system loads. These loads occur on the advancing side of the disk and are not related to blade stall which does not occur for these weight coefficients. At high weight coefficients aerodynamic and structural limits are related to dynamic stall cycles that begin on the retreating side of the blade and, for the most severe conditions, carry around to the advancing side of the blade at the presumed first frequency of the blade/control system.

Coleman, Colin P.↗
NASA NTRS1972

Wind tunnel investigation of a large scale 35 deg swept wing jet transport model with an external blowing triple slotted flap

An investigation was conducted to determine the aerodynamic characteristics of a large-scale subsonic jet transport model with an externally jet-augmented flap system that would augment lift and provide direct-lift control. The model had a 35 deg swept wing of aspect ratio 7.82 and two side-by-side engines mounted on a single pylon under each wing close to the fuselage. The lift of the flap system was augmented by jet engine exhaust impingement on the triple-slotted flap surfaces. The rearmost flap provided direct lift control. Results were obtained for several combinations of flap deflections at gross thrust coefficients from 0 to 2.0. Three-component longitudinal data are presented with four engines operating. Limited longitudinal and lateral data are presented for asymmetric and symmetric thrust conditions with three engines operating. For the same overall flap deflection, lift coefficient and maximum lift coefficient were improved 13 and 7 percent compared to coefficients obtained with a double-slotted flap configuration. A maximum lift coefficient of 6.3 was obtained at a gross thrust coefficient of 2.0. At the same flap deflection lateral and directional trim moment requirements with an engine inoperative were reduced 55 and 33 percent, respectively, compared to those with the engines located farther outboard on the wing. Trim moment requirements in pitch were also reduced significantly. However, pitching-moment instability occurred and increased with gross thrust coefficient.

Aoyagi, K.↗
NASA NTRS1977

An investigation of a close-coupled canard as a direct side-force generator on a fighter model at Mach numbers from 0.40 to 0.90

The canard panels had 5 deg of dihedral and were deflected differentially or individually over an incidence range from 10 deg to -10 deg and a model angle-of-attack range from -4 deg to 15 deg. Significant side forces were generated in a transonic tunnel by differential and single canard-panel deflections over the Mach number and angle-of-attack ranges. The yawing moment resulting from the forward location of the generated side force would necessitate a vertical tail/rudder trim force which would augment the forebody side force and be of comparable magnitude. Incremental side forces, yawing moments, lift, and pitching moments due to single canard-panel deflections were additive; that is, their sums were essentially the same as the forces and moments produced by differential canard-panel deflections of the same magnitude. Differential and single canard-panel deflections produced negligible rolling moments over the Mach number and angle-of-attack ranges.

Re, R. J.↗
NASA NTRS1996

Wind-tunnel development of an SR-71 aerospike rocket flight test configuration

A flight experiment has been proposed to investigate the performance of an aerospike rocket motor installed in a lifting body configuration. An SR-71 airplane would be used to carry the aerospike configuration to the desired flight test conditions. Wind-tunnel tests were completed on a 4-percent scale SR-71 airplane with the aerospike pod mounted in various locations on the upper fuselage. Testing was accomplished using sting and blade mounts from Mach 0.6 to Mach 3.2. Initial test objectives included assessing transonic drag and supersonic lateral-directional stability and control. During these tests, flight simulations were run with wind-tunnel data to assess the acceptability of the configurations. Early testing demonstrated that the initial configuration with the aerospike pod near the SR-71 center of gravity was unsuitable because of large nosedown pitching moments at transonic speeds. The excessive trim drag resulting from accommodating this pitching moment far exceeded the excess thrust capability of the airplane. Wind-tunnel testing continued in an attempt to find a configuration suitable for flight test. Multiple configurations were tested. Results indicate that an aft-mounted model configuration possessed acceptable performance, stability, and control characteristics.

Smith, Stephen C.↗
NASA NTRS1959

Stability and Control Characteristics at Subsonic Speeds of a Flat-Top Arrowhead Wing-Body Combination

A wind-tunnel investigation was made to determine the longitudinal- and lateral-stability derivatives of a flat-top wing-body configuration at Mach numbers from 0.22 to 0.90 and Reynolds numbers of 3.5 and 17 million. The wing had a leading-edge sweepback of 78.9 deg and a cathedral of 45 deg on the outer panels. The tests included the determination of the effectiveness of elevon and rudder controls and also an investigation of ground effects. The model was tested at angles of attack up to 28 deg and angles of sideslip up to 18 deg. The dynamic response of this configuration has been determined from the wind-tunnel data for a simulated airplane having a wing loading of 17.7 pounds per square foot. The longitudinal data show a forward shift in aerodynamic center of 10 percent of the mean aerodynamic chord as the lift coefficient is increased above 0.1. Although flown in the lift range of decreasing stability, the simulated airplane did not encounter pitch-up in maneuvers initiated from steady level flight with zero static margin unless a load factor of 2.2 was exceeded. This maneuver margin was provided by a large value of pitching moment due to pitching velocity. The number of cycles to damp the Dutch roll mode to half amplitude, the time constants of the roll subsidence and spiral divergence modes, and control effectiveness in roll are computed. The lateral stability is shown to be positive but is marginal in meeting the military specifications for today's aircraft. An analog computer study has been made in five degrees of freedom (constant velocity) which illustrates that the handling characteristics are satisfactory. Several programed rolling maneuvers and coordinated turns also illustrate the handling qualities of the airplane.

Buell, Donald A.↗
NASA NTRS1948

Preliminary Results of an Investigation by the Wing-Flow Method of the Longitudinal Stability Characteristics of a 1/50-Scale Semispan Model of the McDonnell XP-88 Airplane

This paper presents the results of measurements of longitudinal stability of a 1/50-scale model of the XP-88 airplane by the wing-flow method. Lift, rolling-moment, hinge-moment, and pitching-moment characteristics as well as the downwash at the tail were measured over a Mach number range from approximately 0.5 to 1.05 at Reynolds numbers below 1,000,000. No measurements of drag were obtained. No abrupt changes due to Mach number were noted in any of the parameters measured. The data indicated that the wing was subject to early tip stalling; that the tail effectiveness decreased gradually with increasing Mach number up to M = 0.9, but increased again at higher Mach numbers; that the variation of downwash with angle of attack did not change appreciably with Mach number except between 0.95 and 1.0 where d(epsilon)/d(alpha), decreased from 0.46 to 0.32; that at zero lift with a stabilizer setting of -1.5 deg there was a gradually increasing nosing-up tendency with increasing Mach number; and that the control-fixed stability in maneuvers at constant speed gradually increased with increasing Mach number.

Crane, Harold L.↗
NASA NTRSDate not supplied

Numerical Implementation of Source Terms to Evaluate Active Porosity Control using a Transpiration Cooled Thermal Protection System

Transpiration cooling has renewed interest of study as a renewable system of thermal protection for atmospheric entry systems. The presence of coolant within the void space of a porous material changes its effective porosity and theorized to lend the external heatshield as a potential means of porous surface control. Effective porosity is explored in two forms: saturation of void space where exiting coolant creates ‘blowing’ over the surface, and partial evacuation of the void space where withdrawal of the coolant creates ‘suction’ on the surface. Thus this study evaluates using transpiration cooling as a as means of active aerodynamic control. The feasibility of the system is evaluated numerically using Reynolds-averaged Navier Stokes based computational fluid dynamics for the aerodynamic assessments by coding source terms of transpiration cooling products at a heat shield surface boundary at the wind side shoulder, creating an asymmetric scheme. Study results show induced moments about the pitch axis incurred following the source terms of a cooling fluid at a near-shoulder location on the heat shield. Lift and drag saw increasing modulation with increase in mass flux rate. Pitch moment was altered a total of 388 N-m between lowest and highest ‘suction’ rates and changed 194 N-m maximum between ‘blowing’ rates.

transpiration cooling↗
NASA NTRS1983

Family of airfoil shapes for rotating blades

An airfoil which has particular application to the blade or blades of rotor aircraft such as helicopters and aircraft propellers is described. The airfoil thickness distribution and camber are shaped to maintain a near zero pitching moment coefficient over a wide range of lift coefficients and provide a zero pitching moment coefficient at section Mach numbers near 0.80 and to increase the drag divergence Mach number resulting in superior aircraft performance.

Noonan, K. W.↗
NASA NTRS2004

Rotor Airloads Prediction Using Loose Aerodynamic Structural Coupling

This work couples a computational fluid dynamics (CFD) code and rotorcraft computational structural dynamics (CSD) code to calculate helicopter rotor airloads across a range of flight conditions. An iterative loose (weak) coupling methodology is used to couple the CFD and CSD codes on a per revolution, periodic basis. The CFD uses a high fidelity, Navier-Stokes, overset grid methodology with first principles-based wake capturing. Modifications are made to the CFD code for aeroelastic analysis. For a UH-60A Blackhawk helicopter, four challenging level flight conditions are computed: 1) low speed (u = 0.15) with blade-vortex interaction, 2) high speed (u = 0.37) with advancing blade negative lift, 3) high thrust with dynamic stall (u = 0.24), and 4) hover. Results are compared with UH-60A Airloads Program fight test data. Most importantly, for all cases the loose coupling methodology is shown to be stable, convergent, and robust with full coupling of normal force, pitching moment, and chord force. In comparison with flight test data, normal force and pitching moment magnitudes are in good agreement. For the high speed and dynamic stall cases a phase lag in comparison with the data is seen, nonetheless, the shapes of the curves are very good. Overall, the results are noteworthy improvement over lifting line aerodynamics used in rotorcraft comprehensive codes.

Potsdam, Mark↗