Search NASA⌕ Search

SEARCH · Search NASA

Results for “PROPULSIVE EFFICIENCY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Large-scale Advanced Prop-fan (LAP) static rotor test report

Discussed is Static Rotor Testing of the SR-7L Large Scale Advanced Prop-Fan (LAP). The LAP is an advanced 9 foot diameter, 8 bladed propeller designed and built by Hamilton Standard under contract to the NASA Lewis Research Center. The Prop-Fan employs thin swept blades to provide efficient propulsion at flight speeds up to Mach .85. Static Testing was conducted on a 10,000 HP whirl rig at Wright Patterson Air Force Base. The test objectives were to investigate the Prop-Fan static aerodynamic and structural dynamic performance, determine the blade steady state stressers and deflections and to measure steady and unsteady pressures on the SR-7L blade surface. The measured performance of the LAP correlated well with analytical predictions at blade pitch angles below 30 deg. A stall buffet phenomenon was observed at blade pitch angles above 30 deg. This phenomenon manifested itself by elevated blade vibratory stress levels and lower than expected thrust produced and power absorbed by the Prop-Fan for a given speed and blade angle.

Degeorge, Charles L.↗
NASA NTRS1989

Hypersonic airbreathing vehicle design - Focus on aero-space plane

Creating a viable, 'aerospaceplane' airbreathing SSTO vehicle will require sophisticated configuration synthesis and a synergistic integration of advanced technologies across the spectrum of disciplines. In design exercises conducted to date, reductions in the fuel weight-fraction requirement can result from improvements in aerodynamics/controls, enhanced propulsion efficiencies, and trajectory optimization. Additional improvements in fuel-weight fraction can result from improvements in structural design, heat-management techniques, and materials properties.

Hunt, James L.↗
NASA NTRS1991

Air-breathing hypersonic vehicle guidance and control studies; An integrated trajectory/control analysis methodology: Phase 1

A tool which generates optimal trajectory/control histories in an integrated manner is generically adapted to the treatment of single-stage-to-orbit air-breathing hypersonic vehicles. The methodology is implemented as a two point boundary value problem solution technique. Its use permits an assessment of an entire near-minimum-fuel trajectory and desired control strategy from takeoff to orbit while satisfying physically derived inequality constraints and while achieving efficient propulsive mode phasing. A simpler analysis strategy that partitions the trajectory into several boundary condition matched segments is also included to construct preliminary trajectory and control history representations with less computational burden than is required for the overall flight profile assessment. A demonstration was accomplished using a tabulated example (winged-cone accelerator) vehicle model that is combined with a newly developed multidimensional cubic spline data smoothing routine. A constrained near-fuel-optimal trajectory, imposing a dynamic pressure limit of 1000 psf, was developed from horizontal takeoff to 20,000 ft/sec relative air speed while aiming for a polar orbit. Previously unspecified propulsive discontinuities were located. Flight regimes demanding rapid attitude changes were identified, dictating control effector and closed-loop controller authority was ascertained after evaluating effector use for vehicle trim. Also, inadequacies in vehicle model representations and specific subsystem models with insufficient fidelity were determined based on unusual control characteristics and/or excessive sensitivity to uncertainty.

Hattis, Philip D.↗
NASA NTRS1991

Technology needs for high speed rotorcraft (3)

The spectrum of vertical takeoff and landing (VTOL) type aircraft is examined to determine which aircraft are most likely to achieve high subsonic cruise speeds and have hover qualities similar to a helicopter. Two civil mission profiles are considered: a 600-n.mi. mission for a 15- and a 30-passenger payload. Applying current technology, only the 15- and 30-passenger tiltfold aircraft are capable of attaining the 450-knot design goal. The two tiltfold aircraft at 450 knots and a 30-passenger tiltrotor at 375 knots were further developed for the Task II technology analysis. A program called High-Speed Total Envelope Proprotor (HI-STEP) is recommended to meet several of these issues based on the tiltrotor concept. A program called Tiltfold System (TFS) is recommended based on the tiltrotor concept. A task is identified to resolve the best design speed from productivity and demand considerations based on the technology that emerges from the recommended programs. HI-STEP's goals are to investigate propulsive efficiency, maneuver loads, and aeroelastic stability. Programs currently in progress that may meet the other technology needs include the Integrated High Performance Turbine Engine Technology (IHPTET) (NASA Lewis) and the Advanced Structural Concepts Program funded through NASA Langley.

Detore, Jack↗
NASA NTRS1991

Integrated trajectory and control analysis for generic hypersonic vehicles

A tool which supports integrated assessment of air-breathing hypersonic vehicle trajectory management and control strategy has been developed by Hattis and Malchow (1991). Using a two-point boundary value problem solution technique, the tool can construct an entire near-minimum-fuel trajectory and desired control strategy from takeoff to orbit, while satisfying physically derived inequality constraints and while achieving efficient propulsive mode phasing. A strategy is also formulated to construct preliminary trajectory and control history representations with less computational burden than required for the overall flight profile assessment. A tabulated example hypersonic vehicle model has been used to demonstrate the integrated analysis methodology. To assure good numerical behavior when the algorithm uses tabulated model data, a multidimensional cubic spline curve smoothing routine has been developed. A dynamic-pressure-constrained, near-fuel-optimal trajectory was computed to provide examples of information that the methodology can provide. Previously unspecified propulsive discontinuities were located, flight regimes demanding rapid attitude changes were identified, available and closed-loop controller authority was ascertained, and inadequacies in vehicle and specific subsystem model representations were determined.

Hattis, Philip D.↗
NASA NTRS1991

The necessity of on board oxygen for airbreathing single-stage-to-orbit vehicles

Vehicle performance and sizing impacts of stored oxygen are examined for SSTO vehicles such as the National Aerospace Plane. The relationship between propulsion efficiency and thrust-to-drag ratio is presented. Idealistic and substantive values for these parameters are compared. The impact of these two parameters as well as propellant density on vehicle sizing is investigated. Representative configurations are provided for comparison purposes.

Martin, John G.↗
NASA NTRS1992

Design of high speed proprotors using multiobjective optimization techniques

An integrated, multiobjective optimization procedure is developed for the design of high speed proprotors with the coupling of aerodynamic, dynamic, aeroelastic, and structural criteria. The objectives are to maximize propulsive efficiency in high speed cruise and rotor figure of merit in hover. Constraints are imposed on rotor blade aeroelastic stability in cruise and on total blade weight. Two different multiobjective formulation procedures, the Min summation of beta and the K-S function approaches are used to formulate the two-objective optimization problems.

Mccarthy, Thomas R.↗
NASA NTRS1992

Optimum design of high speed prop rotors including the coupling of performance, aeroelastic stability and structures

An optimization procedure is developed for the design of high speed prop-rotors to be used in civil tiltrotor applications. The goal is to couple aerodynamic performance, aeroelastic stability, and structural design requirements inside a closed-loop optimization procedure. The objective is to minimize the gross weight and maximize the propulsive efficiency in high speed cruise. Constraints are imposed on the rotor aeroelastic stability in both hover and cruise and rotor figure of merit in hover. Both structural and aerodynamic design variables are used.

Chattopadhyay, Aditi↗
NASA NTRS1990

Simulation of unsteady rotational flow over propfan configuration

During the past decade, aircraft engine manufacturers and scientists at NASA have worked on extending the high propulsive efficiency of a classical propeller to higher cruise Mach numbers. The resulting configurations use highly swept twisted and very thin blades to delay the drag divergence Mach number. Unfortunately, these blades are also susceptible to aeroelastic instabilities. This was observed for some advanced propeller configurations in wind tunnel tests at NASA Lewis Research Center, where the blades fluttered at cruise speeds. To address this problem and to understand the flow phenomena and the solid fluid interaction involved, a research effort was initiated at Georgia Institute of Technology in 1986, under the support of the Structural Dynamics Branch of the NASA Lewis Research Center. The objectives of this study are: (1) the development of solution procedures and computer codes capable of predicting the aeroelastic characteristics of modern single and counter-rotation propellers; and (2) the use of these solution procedures to understand physical phenomena such as stall flutter, transonic flutter, and divergence.

Srivastava, Rakesh↗
NASA NTRS1993

Rotor design optimization using a free wake analysis

The aim of this effort was to develop a comprehensive performance optimization capability for tiltrotor and helicopter blades. The analysis incorporates the validated EHPIC (Evaluation of Hover Performance using Influence Coefficients) model of helicopter rotor aerodynamics within a general linear/quadratic programming algorithm that allows optimization using a variety of objective functions involving the performance. The resulting computer code, EHPIC/HERO (HElicopter Rotor Optimization), improves upon several features of the previous EHPIC performance model and allows optimization utilizing a wide spectrum of design variables, including twist, chord, anhedral, and sweep. The new analysis supports optimization of a variety of objective functions, including weighted measures of rotor thrust, power, and propulsive efficiency. The fundamental strength of the approach is that an efficient search for improved versions of the baseline design can be carried out while retaining the demonstrated accuracy inherent in the EHPIC free wake/vortex lattice performance analysis. Sample problems are described that demonstrate the success of this approach for several representative rotor configurations in hover and axial flight. Features that were introduced to convert earlier demonstration versions of this analysis into a generally applicable tool for researchers and designers is also discussed.

Quackenbush, Todd R.↗
NASA NTRS1993

Nuclear propulsion technology advanced fuels technology

Viewgraphs on advanced fuels technology are presented. Topics covered include: nuclear thermal propulsion reactor and fuel requirements; propulsion efficiency and temperature; uranium fuel compounds; melting point experiments; fabrication techniques; and sintered microspheres.

Stark, Walter A., Jr.↗
NASA NTRS1993

Design of high speed proprotors using multiobjective optimization techniques

A multidisciplinary optimization procedure is developed for the design of high speed proprotors. The objectives are to simultaneously maximize the propulsive efficiency in high speed cruise without sacrificing the rotor figure of merit in hover. Since the problem involves multiple design objectives, multiobjective function formulation techniques are used. A derailed two-celled isotropic box beam is used to model the load carrying member within the rotor blade. Constraints are imposed on rotor blade aeroelastic stability in cruise, the first natural frequency in hover and total blade weight. Both aerodynamic and structural design variables are used. The results obtained using both techniques are compared to the reference rotor and show significant aerodynamic performance improvements without sacrificing dynamic and aeroelastic stability requirements.

Mccarthy, Thomas R.↗
NASA NTRS1991

Effect of heat release on the stability of compressible reacting mixing layer

Reacting free shear layers are of fundamental importance in many industrial systems including gas turbine combustors and rockets. Efficient propulsion systems are essential for air breathing supersonic ramjets in the high Mach number range. A limiting factor in these engines is the time for fuel and oxidizer to mix in the combustion chamber; for fast mixing, the flow must be vigorously turbulent which requires the laminar flow to be unstable. Understanding the stability characteristics of compressible reacting free shear layers is, therefore, very important and may allow one to control the flow. Low speed shear layers are highly unstable but, as chemical reaction and compressibility effects tend to stabilize them, it is important to investigate the stability of high speed reacting mixing layers. The latter consists of two fluid streams containing fuel and oxidizer respectively, and the conclusions are expected to apply, with quantitative modifications, to other shear flows, e.g., jets. Since low speed reacting cases have been studied earlier, we concentrate on the effects of Mach number and heat release. We are primarily interested in solving the stability problem over a large range of Mach number and heat release. In order to understand the effect of the heat release on the stability of this flow, one must first study the characteristics of the non-reacting flow. Inviscid theory is a reliable guide for understanding stability of compressible shear flows at moderate and large Reynolds numbers and is the basis for this work.

Shin, Dong-Shin↗
NASA NTRS1924

A method of determining the dimensions and horsepower of an airship for any given performance

A simple and easily applied method of calculating the dimensions and horsepower necessary for an airship to have any given performance is described and illustrated by examples. The method includes means for estimating the changes in performance or in size when modifications or new features are introduced into a design, involving increase or saving in weights, or changes in resistance or propulsive efficiency.

Burgess, C P↗
NASA NTRS1932

Tests of Nacelle-Propeller Combinations in Various Positions with Reference to Wings II : Thick Wing - Various Radial-Engine Cowlings - Tractor Propeller

This report is the second of a series giving the results obtained in the 20-foot wind tunnel of the National Advisory Committee for Aeronautics on the interference drag and propulsive efficiency of nacelle-propeller-wing combinations. The first report gave the results of the test of a N.A.C.A. cowled air-cooled engine nacelle located in 21 positions with reference to a thick wing. The present report gives results of tests of a normal engine nacelle with several types of cowling and fairings in four of the positions with reference to the same wing. (author)

Wood, Donald H↗
NASA NTRS1929

Full Scale Tests of Wood Propellers on a VE-7 Airplane in the Propeller Research Tunnel

The investigation described in this report was made primarily to afford a comparison between propeller tests in the new propeller research tunnel and flight tests and small model tests on propellers. Three wood propellers which had been previously tested in flight on a VE-7 airplane, and of which models had also been tested in a wind tunnel, were tested again on a VE-7 airplane in the propeller research tunnel. The results of these tests are in fair agreement with those of the flight and model tests. Tests were also made with the tail surfaces removed, and with both the wing and tail surfaces removed. It was found that the effect of the tail surfaces on the propeller characteristics was negligible, but that the wings reduced the maximum propulsive efficiency about 5 percent. (author)

Weick, Fred E↗
NASA NTRS1929

Full Scale Tests on a Thin Metal Propeller at Various Tip Speeds

This report describes an investigation made in order to determine the effect of tip speed on the characteristics of a thin-bladed metal propeller. The propeller was mounted on a VE-7 airplane with a 180-HP E-2 engine, and tested in the 20-foot propeller research tunnel of the National Advisory Committee for Aeronautics. It was found that the effect of tip speed on the propulsive efficiency was negligible within the range of the tests, which was from 600 to 1,000 feet per second (about 0.5 to 0.9 the velocity of sound in air). (author)

Weick, Fred E↗