Search NASA⌕ Search

SEARCH · Search NASA

Results for “Performance analysis and profiling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Airloads and Wake Geometry Calculations for an Isolated Tiltrotor Model in a Wind Tunnel

Comparisons of measured and calculated aerodynamic behavior of a tiltrotor model are presented. The test of the Tilt Rotor Aeroacoustic Model (TRAM) with a single, 0.25-scale V-22 rotor in the German-Dutch Wind Tunnel (DNW) provides an extensive set of aeroacoustic, performance, and structural loads data. The calculations were performed using the rotorcraft comprehensive analysis CAMRAD II. Presented are comparisons of measured and calculated performance for hover and helicopter mode operation, and airloads for helicopter mode. Calculated induced power, profile power, and wake geometry provide additional information about the aerodynamic behavior. An aerodynamic and wake model and calculation procedure that reflects the unique geometry and phenomena of tiltrotors has been developed. There are major differences between this model and the corresponding aerodynamic and wake model that has been established for helicopter rotors. In general, good correlation between measured and calculated performance and airloads behavior has been shown. Two aspects of the analysis that clearly need improvement are the stall delay model and the trailed vortex formation model.

Johnson, Wayne↗
NASA NTRS1981

The Pinhole/Occulter Facility

A large occulting system in space can be used for high resolution X-ray observations and for large aperture coronagraphic observations in visible and UV light. The X-ray observations can combine high angular resolution in hand (10 keV) X-radiation with the high sensitivity of a multiple pinhole camera, and can permit sensitive observations of bremsstrahlung from nonthermal particles in the corona. The large aperture coronagraphs have two major advantages: high angular resolution and good photon collection. This will permit observations of small scale structures in the corona for the first time and will give sufficient counting rates above the coronal background rates for sensitive diagnostic analysis of intensities and line profiles for coronal structures in the solar wind acceleration region. The technical basis for performing observations with a large occulting system in these three wavelength ranges is described as well as a pinhole/occulter facility presently being considered for Spacelab. Some indications about future developments are included.

Hudson, H. S.↗
NASA NTRS1984

A statistical evaluation and comparison of VISSR Atmospheric Sounder (VAS) data

In order to account for the temporal and spatial discrepancies between the VAS and rawinsonde soundings, the rawinsonde data were adjusted to a common hour of release where the new observation time corresponded to the satellite scan time. Both the satellite and rawinsonde observations of the basic atmospheric parameters (T Td, and Z) were objectively analyzed to a uniform grid maintaining the same mesoscale structure in each data set. The performance of each retrieval algorithm in producing accurate and representative soundings was evaluated using statistical parameters such as the mean, standard deviation, and root mean square of the difference fields for each parameter and grid level. Horizontal structure was also qualitatively evaluated by examining atmospheric features on constant pressure surfaces. An analysis of the vertical structure of the atmosphere were also performed by looking at colocated and grid mean vertical profiles of both the satellite and rawinsonde data sets. Highlights of these results are presented.

Jedlovec, G. J.↗
NASA NTRS1989

Space Shuttle 2 Advanced Space Transportation System. Volume 1: Executive Summary

An investigation into the feasibility of establishing a second generation space transportation system is summarized. Incorporating successful systems from the Space Shuttle and technological advances made since its conception, the second generation shuttle was designed to be a lower-cost, reliable system which would guarantee access to space well into the next century. A fully reusable, all-liquid propellant booster/orbiter combination using parallel burn was selected as the base configuration. Vehicle characteristics were determined from NASA ground rules and optimization evaluations. The launch profile was constructed from particulars of the vehicle design and known orbital requirements. A stability and control analysis was performed for the landing phase of the orbiter's flight. Finally, a preliminary safety analysis was performed to indicate possible failure modes and consequences.

Adinaro, James N.↗
NASA NTRS2007

Analysis Method for Non-Nominal First Acquisition

First this paper describes a method how the trajectory of the launcher can be modelled for the contingency analysis without having much information about the launch vehicle itself. From a dense sequence of state vectors a velocity profile is derived which is sufficiently accurate to enable the Flight Dynamics Team to integrate parts of the launcher trajectory on its own and to simulate contingency cases by modifying the velocity profile. Then the paper focuses on the thorough visibility analysis which has to follow the contingency case or burn performance simulations. In the ideal case it is possible to identify a ground station which is able to acquire the satellite independent from the burn performance. The correlations between the burn performance and the pointing at subsequent ground stations are derived with the aim of establishing simple guidelines which can be applied quickly and which significantly improve the chance of acquisition at subsequent ground stations. In the paper the method is applied to the Soyuz/Fregat launch with the MetOp satellite. Overall the paper shows that the launcher trajectory modelling with the simulation of contingency cases in connection with a ground station visibility analysis leads to a proper selection of ground stations and acquisition methods. In the MetOp case this ensured successful contact of all ground stations during the first hour after separation without having to rely on any early orbit determination result or state vector update.

Sieg, Detlef↗
NASA NTRS1993

Depth-diameter ratios for Martian impact craters: Implications for target properties and episodes of degradation

This study determines crater depth through use of photoclinometric profiles. Random checks of the photoclinometric results are performed using shadow estimation techniques. The images are Viking Orbiter digital format frames; in cases where the digital image is unusable for photoclinometric analysis, shadow estimation is used to determine crater depths. The two techniques provide depth results within 2 percent of each other. Crater diameters are obtained from the photoclinometric profiles and checked against the diameters measured from the hard-copy images using a digitizer. All images used in this analysis are of approximately 40 m/pixel resolution. The sites that have been analyzed to date include areas within Arabia, Maja Valles, Memnonia, Acidalia, and Elysium. Only results for simple craters (craters less than 5 km in diameter) are discussed here because of the low numbers of complex craters presently measured in the analysis. General results indicate that impact craters are deeper than average. A single d/D relationship for fresh impact craters on Mars does not exist due to changes in target properties across the planet's surface. Within regions where target properties are approximately constant, however, d/D ratios for fresh craters can be determined. In these regions, the d/D ratios of nonpristine craters can be compared with the fresh crater d/D relationship to obtain information on relative degrees of crater degradation. This technique reveals that regional episodes of enhanced degradation have occurred. However, the lack of statistically reliable size-frequency distribution data prevents comparison of the relative ages of these events between different regions, and thus determination of a large-scale episode (or perhaps several episodes) cannot be made at this time.

Barlow, N. G.↗
NASA NTRS1976

EDIN design study alternate space shuttle booster replacement concepts. Volume 2: Design simulation results

Historical weight estimating relationships were developed for the liquid rocket booster (LRB) using Saturn technology, and modified as required to support the EDIN05 study. Mission performance was computed using February 1975 shuttle configuration groundrules to allow reasonable comparison of the existing shuttle with the EDIN05 designs. The launch trajectory was constrained to pass through both the RTLS/AOA and main engine cut-off points. Performance analysis was based on a point design trajectory model which optimized initial tilt rate and exo-atmospheric pitch profile. A gravity turn was employed during the boost phase in place of the shuttle angle-of-attack profile. Engine throttling add/or shutdown was used to constrain dynamic pressure and/or longitudinal acceleration where necessary.

Demakes, P. T.↗
NASA NTRS1989

Electron acceleration at nearly perpendicular collisionless shocks. I - One-dimensional simulations without electron scale fluctuations

Under certain conditions electrons can be reflected and effectively energized at quasi-perpendicular shocks. This process is most prominent close to the point where the upstream magnetic field is tangent to the curved shock. A theoretical explanation of the underlying physical mechanism has been proposed which assumes conservation of magnetic moment and a static, simplified shock profile are performed. Test particle calculations of the electron reflection process in order to examine the results of the theoretical analysis without imposing these restrictive conditions. A one-dimensional hybrid simulation code generates the characteristic field variations across the shock. Special emphasis is placed on the spatial and temporal length scales involved in the mirroring process. The simulation results agree generally well with the predictions from adiabatic theory. The effects of the cross-shock potential and unsteadiness are quantified, and the influence of field fluctuations on the reflection process is discussed.

Krauss-Varban, D.↗
NASA NTRS1994

Ozone transport during a cut-off low event studied in the frame of the TOASTE program

A study of ozone transfer to the troposphere has been performed during two phases of the evolution of a cut-off low using both ozone vertical profiles and objective analysis of the ECMWF to compute potential vorticity distributions and air mass trajectories. Ozone profiles were measured by a ground based lidar system at the Observatoire de Haute Provence (OHP, 43 deg 55 N, 5 deg 42 E). A stratospheric ozone transport into the troposphere has been observed during a tropopause fold which occurred at the beginning of the cut-off low formation and during the erosion phase of the cut-off low. From the estimate of the maximum ozone content transferred to the troposphere, both mechanisms have the same order of magnitude of influence on the ozone flux to the troposphere. On a time scale of a few days, the correlation is very good between the potential vorticity and the ozone time evolution in the vicinity of the upper level frontal system.

Ancellet, G.↗
NASA NTRS1997

High Temperature Transparent Furnace Development

This report describes the use of novel techniques for heat containment that could be used to build a high temperature transparent furnace. The primary objective of the work was to experimentally demonstrate transparent furnace operation at 1200 C. Secondary objectives were to understand furnace operation and furnace component specification to enable the design and construction of a low power prototype furnace for delivery to NASA in a follow-up project. The basic approach of the research was to couple high temperature component design with simple concept demonstration experiments that modify a commercially available transparent furnace rated at lower temperature. A detailed energy balance of the operating transparent furnace was performed, calculating heat losses through the furnace components as a result of conduction, radiation, and convection. The transparent furnace shells and furnace components were redesigned to permit furnace operation at at least 1200 C. Techniques were developed that are expected to lead to significantly improved heat containment compared with current transparent furnaces. The design of a thermal profile in a multizone high temperature transparent furnace design was also addressed. Experiments were performed to verify the energy balance analysis, to demonstrate some of the major furnace improvement techniques developed, and to demonstrate the overall feasibility of a high temperature transparent furnace. The important objective of the research was achieved: to demonstrate the feasibility of operating a transparent furnace at 1200 C.

Bates, Stephen C.↗
NASA NTRS1955

Aerodynamic Design of Axial-flow Compressors. VI - Experimental Flow in Two-Dimensional Cascades

Available experimental two-dimensional cascade data for conventional compressor blade sections are correlated at a reference incidence angle in the region of minimum loss. Variations of reference incidence angle, total-pressure loss, and deviation angle with cascade geometry, inlet Mach number, and Reynolds number are investigated. From the analysis and the correlations of the available data, rules and relations are evolved for the prediction of blade-profile performance. These relations are developed in simplified forms readily applicable to compressor design procedures.

Lieblein, Seymour↗
NASA NTRS1987

Thermal stress cycling of GaAs solar cells

Thermal stress cycling was performed on gallium arsenide solar cells to investigate their electrical, mechanical, and structural integrity. Cells were cycled under low Earth orbit (LEO) simulated temperature conditions in vacuum. Cell evaluations consisted of power output values, spectral response, optical microscopy and ion microprobe mass analysis, and depth profiles on both front surface inter-grid areas and metallization contact grid lines. Cells were examined for degradation after 500, 5,000, 10,000 and 15,245 thermal cycles. No indication of performance degradation was found for any vendor's cell lot.

Francis, Robert W.↗
NASA NTRS1977

Solar concentration by curved-base Fresnel lenses

The solar concentration performance of idealized curved base line focusing Fresnel lenses is analyzed. A simple optical model was introduced to study the effects of base curvature and lens f-number. Thin lens ray tracing and the laws of reflection and refraction are used to develop expression for lens transmittance and image plane intensity profiles. The intensity distribution over the solar spectrum, lens dispersion effects, and absorption by the lens material are included in the analysis. Model capabilities include assessment of lens performance in the presence of small transverse tracking errors and the sensitivity of solar image characteristics to focusing.

Cosby, R. M.↗
NASA NTRS2003

Effects of Mean Flow Profiles on Instability of a Low-Density Gas Jet Injected into a High-Density Gas

The objective of this study was to investigate the effects of the mean flow profiles on the instability characteristics in the near-injector region of low-density gas jets injected into high-density ambient gas mediums. To achieve this, a linear temporal stability analysis and a spatio-temporal stability analysis of a low-density round gas jet injected vertically upwards into a high-density ambient gas were performed by assuming three different sets of mean velocity and density profiles. The flow was assumed to be isothermal and locally parallel. Viscous and diffusive effects were ignored. The mean flow parameters were represented as the sum of the mean value and a small normal-mode fluctuation. A second order differential equation governing the pressure disturbance amplitude was derived from the basic conservation equations. The first set of mean velocity and density profiles assumed were those used by Monkewitz and Sohn for investigating absolute instability in hot jets. The second set of velocity and density profiles assumed for this study were the ones used by Lawson. And the third set of mean profiles included a parabolic velocity profile and a hyperbolic tangent density profile. The effects of the inhomogeneous shear layer and the Froude number (signifying the effects of gravity) on the temporal and spatio-temporal results for each set of mean profiles were delineated. Additional information is included in the original extended abstract.

Vedantam, Nanda Kishore↗
NASA NTRS2015

Evaluating Performance of UAS Detect-And-Avoid System Using a Fast-Time Simulation Tool

Most unmanned aircraft systems will be required to be equipped with a Detect-and-Avoid (DAA) system. The surveillance performance of the DAA system to detect and track intruder aircraft will depend on the encounter geometries that unmanned aircraft are expected to have with other aircraft in the airspace. The performance of DAA alerting and avoidance system is also dependent on the timeliness of alerting for UAS pilots to give a sufficient time to determine and command a resolution maneuver to avoid well clear separation violations. This presentation introduces general background of UAS DAA systems and concept of well clear separation standard to satisfy see and avoid regulations. The presentation shows the several UAS mission profiles and analysis of the encounter geometries that were simulated using historical VFR traffic data and some proposed UAS missions. This presentation introduces several potential metrics for evaluating the performance of a DAA system and shows the results that measured through fast-time simulation with traffic scenarios that include NAS-wide VFR manned aircraft and IFR UAS flights. At the end, some research areas will be briefly discussed.

UAS↗
NASA NTRS1972

Analysis and testing of high entrainment single nozzle jet pumps with variable mixing tubes

An analytical model was developed to predict the performance characteristics of axisymmetric single-nozzle jet pumps with variable area mixing tubes. The primary flow may be subsonic or supersonic. The computer program uses integral techniques to calculate the velocity profiles and the wall static pressures that result from the mixing of the supersonic primary jet and the subsonic secondary flow. An experimental program was conducted to measure mixing tube wall static pressure variations, velocity profiles, and temperature profiles in a variable area mixing tube with a supersonic primary jet. Static pressure variations were measured at four different secondary flow rates. These test results were used to evaluate the analytical model. The analytical results compared well to the experimental data. Therefore, the analysis is believed to be ready for use to relate jet pump performance characteristics to mixing tube design.

Hickman, K. E.↗
NASA NTRS2004

Regional Scale Meteorological Analysis and Prediction Using GPS Occultation and EOS Data

The main objective of the research under this award is to improve regional meteorological analysis and prediction for traditionally data limited regions, particularly over the Southern Ocean and Antarctica, using the remote sensing observations from current and upcoming GPS radio occultation missions and the EOS instrument suite. The major components of this project are: 1.Develop and improve the methods for retrieving temperature, moisture, and pressure profiles from GPS radio occultation data and EOS radiometer data. 2. Develop and improve a regional scale data assimilation system (MM5 4DVAR). 3. Perform case studies involving data analysis and numerical modeling to investigate the impact of different data for regional meteorological analysis and the importance of data assimilation for regional meteorological simulation over the Antarctic region. 4. Apply the findings and improvements from the above studies to weather forecasting experiments. 5. In the third year of the award we made significant progress toward the remaining goals of the project. The work included carefully evaluating the performance of an atmospheric mesoscale model, the Polar MM5 in Antarctic applications and improving the upper boundary condition.

Bromwich, David H.↗