Search NASA⌕ Search

SEARCH · Search NASA

Results for “Photoluminescence Spectroscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Optimizing performance and yield of vertical GaN diodes using wafer scale optical techniques

Abstract To improve the manufacturing of vertical GaN devices for power electronics applications, the effects of defects in GaN substrates need to be better understood. Many non-destructive techniques including photoluminescence, Raman spectroscopy and optical profilometry, can be used to detect defects in the substrate and epitaxial layers. Raman spectroscopy was used to identify points of high crystal stress and non-uniform conductivity in a substrate, while optical profilometry was used to identify bumps and pits in a substrate which could cause catastrophic device failures. The effect of the defects was studied using vertical P-i-N diodes with a single zone junction termination extention (JTE) edge termination and isolation, which were formed via nitrogen implantation. Diodes were fabricated on and off of sample abnormalities to study their effects. From electrical measurements, it was discovered that the devices could consistently block voltages over 1000 V (near the theoretical value of the epitaxial layer design), and the forward bias behavior could consistently produce on-resistance below 2 mΩ cm 2 , which is an excellent value considering DC biasing was used and no substrate thinning was performed. It was found that high crystal stress increased the probability of device failure from 6 to 20%, while an inhomogeneous carrier concentration had little effect on reverse bias behavior, and slightly (~ 3%) increased the on-resistance (R on ). Optical profilometry was able to detect regions of high surface roughness, bumps, and pits; in which, the majority of the defects detected were benign. However a large bump in the termination region of the JTE or a deep pit can induce a low voltage catastrophic failure, and increased crystal stress detected by the Raman correlated to the optical profilometry with associated surface topography.

42 ENGINEERING↗
DOE OSTI2022

Ultrafast charge transfer and carrier dynamics in a WS 2 /MoSe 2 few-layer van der Waals heterostructure

Photocarrier dynamics including interlayer charge transfer and intralayer valley scattering are studied in a heterostructure formed by trilayer WS 2 and MoSe 2 . The sample is fabricated by mechanical exfoliation and dry transfer and characterized by atomic force microscopy, Raman spectroscopy, and photoluminescence measurements. The conduction band minima of the two materials are nearly degenerate, representing a unique band alignment. Layer-selective pump–probe measurements are performed with three configurations to reveal a complete picture of the photocarrier dynamics. By comparing the heterostructure with the two individual trilayer materials in each experimental configuration, ultrafast interlayer charge transfer is unambiguously observed, which occurs on the same time scale as the intralayer valley scattering of the photocarriers. The quasi-equilibrium distribution of electrons in the two layers mediate the fast carrier recombination process. Furthermore, these results show that the band structures of the few-layer transition metal dichalcogenides can enable rich photocarrier dynamics with intermediate band alignments that are complementary to the previously studied monolayer–monolayer heterostructures.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Expanding the color palette of bicolor-emitting nanocrystals

Owing to their bright and tunable luminescence spectra, nanocrystals appear as a unique playground for light source design. Displays and lighting require white light sources that combine several narrow lines. As Kasha's rule prevents the emission of hot carriers, blends of multiple nanocrystal populations are currently the obvious strategy for broad-band source design. However, a few reports suggest that bicolor emission can also be obtained from a single particle even under weak excitation if a careful design of the exciton scattering mechanism sufficiently slows down its relaxation pathways. A key challenge remains to maintain quantum confinement for color tunability in the same structure, while simultaneously achieving a large size to leverage the critical, slower exciton diffusion or relaxation down to the ground state. In this work, we demonstrate that 2D nanoplatelets offer an original opportunity for the design of confined and large heterostructures. We demonstrate that bicolor emission is not limited to green–red pair and show that blue–yellow and purple–green emissions can be obtained from CdSe/CdTe/CdSe core/crown/crown and CdSe/CdS core/crown heterostructures, respectively.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2020

Tunable valleytronics with symmetry-retaining high polarization degree in SnS x Se 1–x model system

SnS has recently been shown to possess unique valleytronic capability with a large polarization degree, where non-degenerate valleys can be accessed using linearly polarized light, bestowed upon by the unique anisotropy and wavefunction symmetry. It is thus of utmost importance to demonstrate the extension of such effects for the IV–VI system in general, thereby elucidating the generality and tunability of such valleytronics. In this study, we show the highly tunable valleytronics via gradual compositional control of the tin(II) sulfo-selenide (SnS x Se 1–x ) alloy system with excellent retainment of symmetry-determined selection rules. We show the presence of both ΓY and ΓX valleys in all alloy compositions via selectivity in absorption and emission of linearly polarized light by optical reflection (R)/transmission (T) and photoluminescence measurements and tuned the bandgaps of the valleys within a range of 1.28 eV–1.05 eV and 1.48 eV–1.24 eV, respectively. This simultaneous tuning of non-degenerate valleys agrees well with theoretical calculations. We then fitted the bandgap values in compositional space, obtaining bowing parameters as a useful database. We further demonstrated the feasibility of using IV–VI valleytronics systems in general by elucidating the retainment of strong polarization degrees of as high as 91% across all compositions. The generalization of such purely symmetry-dependent valleytronics also opens up opportunities for the discovery of more multi-functional materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Pinning of energy transitions of defects, complexes, and surface states in AlGaN alloys

In this work, we determine the dependence of the defect transition energies, electronic bands, and surface charge neutrality levels in AlGaN. With Vacuum level as reference, we show that energy transitions of localized defects and the surface Fermi level are independent of the alloy composition as electronic bands diverge with the increase in the bandgap as a function of alloy composition. The invariance of localized states on the alloy composition creates a convenient internal reference energy with respect to which other energy states may be measured. We demonstrate a higher generality to the universality rule with the independence of deep transition states of otherwise shallow donor type defects [(+1/+3) transition for VN] and defect complexes (C N +Si III ) in addition to the earlier predicted independent nature of mid-gap states when they are either the antibonding state between cationic impurities and host anion or acceptors at anion sites.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Cryogenic spatial–temporal imaging of surface photocarrier dynamics in MAPbI 3 films at the single grain level

We use cryogenic spatial–temporal photoluminescence (PL) imaging measurements down to 10 K and with short-wavelength, 405 nm laser excitation to study surface charge generation, trapping, and recombination at single bright and dark grains as well as their boundaries in model methylammonium lead iodide (MAPbI 3 ) polycrystalline thin films. These salient conditions are shown to be critical for identifying both the detrimental and cooperative roles of grain microstructures where the dark grains serve as the PL quenching center, while the grain boundaries are largely benign and may promote electron–hole separation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Tuning spin–orbit coupling in (6,5) single-walled carbon nanotube doped with sp 3 defects

Single-walled carbon nanotubes (SWCNTs) containing sp 3 defects are a promising class of optoelectronic materials with bright photoluminescence and demonstrated single-photon emission. Using density functional theory simulations, complemented by measurements, we investigate the electronic structure of a series of quantum defects attached to (6,5) SWCNT with the goal of tuning the spin–orbit coupling by introduction of a heavy atom in the defect structure. We characterize the ground state electronic and spin properties of four synthesized and three potential defects on the tube and find that all of the synthesized defects considered introduce a localized midgap defect-centered state containing a single electron, ≈0.2–0.3 eV above the valence band. The spin density is located at the sp 3 defect site with negligible spin–orbit coupling even with the presence of a Pd atom. Three additional functional groups were tested via computation to increase spin localization near the metal, thereby increasing spin–orbit coupling. We predict that only the chlorodiphosphanepalladium(II)– [Cl(PH 3 ) 2 Pd(II)–] defect results in increased spin–orbit splitting of the defect state and the conduction band associated with the pristine-like SWCNT, a measure of the spin–orbit coupling of excited state transitions. This study suggests that for unpassivated sp 3 defects in (6,5) SWCNT, forming a direct bond between a heavy atom and the sp 3 carbon allows for tuning of spin–orbit coupling.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2021

Direct formation of nitrogen-vacancy centers in nitrogen doped diamond along the trajectories of swift heavy ions

We report depth-resolved photoluminescence measurements of nitrogen-vacancy (NV$^-$) centers formed along the tracks of swift heavy ions in type Ib synthetic single crystal diamonds that had been doped with 100 ppm nitrogen during crystal growth. Analysis of the spectra shows that NV$^-$ centers are formed preferentially within regions where electronic stopping processes dominate and not at the end of the ion range where elastic collisions lead to formation of vacancies and defects. Thermal annealing further increases NV yields after irradiation with SHI preferentially in regions with high vacancy densities. NV centers formed along the tracks of single swift heavy ions can be isolated with lift-out techniques for explorations of color center qubits in quasi 1D registers with average qubit spacing of a few nm and of order 100 color centers per micron along 10 to 30 micron long percolation chains.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

MBE growth and donor doping of coherent ultrawide bandgap AlGaN alloy layers on single-crystal AlN substrates

Single-crystal Aluminum Nitride (AlN) crystals enable the epitaxial growth of ultrawide bandgap Al(Ga)N alloys with drastically lower extended defect densities. Here, we report the plasma-MBE growth conditions for high Al-composition AlGaN alloys on single-crystal AlN substrates. An AlGaN growth guideline map is developed, leading to pseudomorphic Al x Ga 1–x N epitaxial layers with x ~0.6–1.0 Al contents at a growth rate of ~0.3 μm/h. These epitaxial layers exhibit atomic steps, indicating step flow epitaxial growth, and room-temperature band edge emission from ~4.5 to 5.9 eV. Growth conditions are identified in which the background impurity concentrations of O, C, Si, and H in the MBE layers are found to be very near or below detection limits. An interesting Si segregation and gettering behavior is observed at the epitaxial AlGaN/AlN heterojunction with significant implications for the formation and transport of 2D electron or hole gases. Well-controlled intentional Si doping ranging from ~2 × 10 17 to 3 × 10 19 atoms/cm 3 is obtained, with sharp dopant density transition profiles. In Si-doped Al 0.6 Ga 0.4 N epilayers, a room-temperature free electron concentration of ~3 × 10 19 /cm 3 , an electron mobility of ~27 cm 2 /V s, and an n-type resistivity of ~7.5 m Ω cm are obtained. Here, the implications of these findings on electronic and photonic devices on single-crystal AlN substrates are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Coupling of a single tin-vacancy center to a photonic crystal cavity in diamond

In this work, we demonstrate optical coupling between a single tin-vacancy (SnV) center in diamond and a free-standing photonic crystal nanobeam cavity. The cavities are fabricated using quasi-isotropic etching and feature experimentally measured quality factors as high as ~11000. We investigate the dependence of a single SnV center's emission by controlling the cavity wavelength using a laser-induced gas desorption technique. Under resonance conditions, we observe an intensity enhancement of the SnV emission by a factor of 12 and a 16-fold reduction of the SnV lifetime. Based on the large enhancement of the SnV emission rate inside the cavity, we estimate the Purcell factor for the SnV zero-phonon line to be 37 and the coupling efficiency of the SnV center to the cavity, the β factor, to be 95%. Our work paves the way for the realization of quantum photonic devices and systems based on efficient photonic interfaces using the SnV color center in diamond.

42 ENGINEERING↗
DOE OSTI2021

Photoluminescence study of solution-deposited Cu 2 BaSnS 4 thin films

To experimentally identify the character of radiative transitions in trigonal Cu 2 BaSnS 4 , we conduct temperature and excitation intensity dependent photoluminescence (PL) measurements in the temperature range of 15–300 K. The low-temperature near band edge PL spectrum is interpreted as the free exciton at 2.11 eV and the bound exciton at 2.08 eV, coupled with associated phonon-assisted transitions. In the low energy region, we assign the dominant defect emission at 1.96 eV to donor–acceptor-pair recombination and the weak broad emission at 1.6 eV to the free-to-bound transition. The activation energies and temperature shift for the radiative transitions are determined and discussed. Above 90 K, the free exciton recombination becomes the dominant radiative transition, with its energy shift mainly governed by the contribution of optical phonons.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Charge collection and trapping mechanisms in hexagonal boron nitride epilayers

Understanding charge collection and trapping mechanisms is crucial for using hexagonal boron nitride (h-BN) as active layers for many photonic and electronic devices such as deep UV detectors and emitters, neutron detectors, and single photon emitters. Charge collection and trapping mechanisms in h-BN epilayers have been investigated by probing impurity related optical emissions under an applied electrical field. Our results suggested that the existence of oxygen impurities affects the charge collection efficiency and results in an additional emission peak at 3.75 eV, corresponding to a donor-acceptor pair (DAP) recombination involving O N (oxygen residing on the nitrogen site) donors and the V B -H (boron vacancy bonded with hydrogen complex) deep level acceptors. Experimental results further revealed that the applied electric field induces an anti-correlation between the emission intensity of the DAP transition and the charge collection efficiency from which it was shown that it is possible to find an expression to quantitatively measure the maximum charge collection efficiency in h-BN. The results introduce not only a coherent picture for the relationship between common impurities in h-BN and charge collection and trapping mechanisms but also useful insights into possible approaches to improve the quality, purity, and charge collection of the h-BN epilayers.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Modulation of recombination zone position for white perovskite/organic emitter hybrid light-emitting devices

We report metal halide perovskites present specific challenges as emitters in large area, surface emission lighting devices. Among these challenges is the vast difference in carrier mobilities between the perovskite and many organic buffer layers typically used in such device fabrication as transport and blocking layers. This can make it difficult to engineer recombination to achieve white emitting devices generally. However, in this work, we introduce unique modulation of excitonic confinement within the perovskite layer of the device stack to control overall placement of the recombination zone. This results in a white light emitter that is bright and highly tunable, providing a path to realize white perovskite related light-emitting devices.

42 ENGINEERING↗
DOE OSTI2022

Electronic and optical characterization of bulk single crystals of cubic boron nitride (cBN)

Cubic boron nitride (cBN) is a relatively less studied wide bandgap semiconductor despite its many promising mechanical, thermal, and electronic properties. We report on the electronic, structural, and optical characterization of commercial cBN crystal platelets. Temperature dependent transport measurements revealed the charge limited diode behavior of the cBN crystals. The equilibrium Fermi level was determined to be 0.47 eV below the conduction band, and the electron conduction was identified as n-type. Unirradiated dark and amber colored cBN crystals displayed broad photoluminescence emission peaks centered around different wavelengths. RC series zero phonon line defect emission peaks were observed at room temperature from the electron beam irradiated and oxygen ion implanted cBN crystals, making this material a promising candidate for high power microwave devices, next generation power electronics, and future quantum sensing applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Evaluation of crystalline quality of traveling heater method (THM) grown Cd0.9Zn0.1Te0.98Se0.02 crystals

Because of its excellent opto-electronic properties, CdZnTe (CZT) has been the material of choice for x- and gamma-ray detectors operable at room temperature. CZT is the leading commercially available room-temperature radiation detector material today. Although much progress has been made over the past three decades, today's CZT crystals still face certain challenges, especially the presence of the performance-limiting materials defects and the associated relatively high production cost. In this regard, CdxZn1−xTeySe1−y (CZTS) is emerging as a next-generation compound semiconductor, which overcomes some of the limitations of CZT technology for the stated applications. Here, we conducted a study to evaluate the crystalline quality of the traveling heater method grown CZTS with an optimized alloy composition, i.e., Cd0.9Zn0.1Te0.98Se0.02. The as-grown samples were evaluated by low-temperature photoluminescence (PL) spectroscopy and high-resolution x-ray diffraction using the synchrotron light source at Brookhaven National Laboratory. The full width at half maximum of both the PL and x-ray rocking curves was observed to be broadened due to the lattice disorder of the quaternary compound, eventually degrading the crystalline quality. This was consistent with density functional theory calculations.

Roy, U. N. (ORCID:0000000282089680)↗
DOE OSTI2022

Er-doped anatase TiO 2 thin films on LaAlO 3 (001) for quantum interconnects (QuICs)

Rare-earth ions (REIs) doped into solid-state crystal hosts offer an attractive platform for realizing quantum interconnects that can function as quantum memories and quantum repeaters. The 4f valence electrons of REIs are shielded by 5s and 5p electrons and undergo highly coherent transitions even when embedded in host crystals. In particular, Er 3+ has an optical transition in the telecom band that is suitable for low-loss communication. Recently, REIs in thin film systems have gained interest due to potential advantages in providing a flexible host crystal environment, enabling scalable on-chip integration with other quantum devices. Here, we investigate the structural and optical properties of Er-doped anatase TiO 2 thin films on LaAlO 3 (001) substrates. By choosing a system with minimal lattice mismatch and adjusting Er-dopant concentration, we achieve optical inhomogeneous linewidths of 5 GHz at 4.5 K. Furthermore, we show that 9 nm-thick buffer and capping layers can reduce the linewidth by more than 40%, suggesting a pathway to further narrowing linewidths in this system. We also identify that Er 3+ ions mainly incorporate into substitutional Ti 4+ sites with non-polar D 2d symmetry, which makes Er dopants insensitive to the first order to local electric fields from impurities and is desirable for coherence properties of Er 3+ spins.

42 ENGINEERING↗
DOE OSTI2023

Amplified spontaneous emission from europium-based molecular complexes coupled to photonic crystal cavities

Rare-earth ion-based materials bear many remarkable optical properties that render them highly appealing for lighting and quantum-related applications. However, their small oscillator strength and weak emission often pose limitations. Here, in this work, we synthesize and couple Eu(III)-based molecular complexes to nanobeam photonic crystals supporting air modes. A reasonable spatial overlap between the molecular complexes and cavity modes leads to an average spontaneous emission coupling efficiency of 0.19. Our pump power-dependent photoluminescence measurements evidence amplified spontaneous emission from the molecular complexes with an amplification threshold as low as 4.4 W/cm 2 , likely benefiting from the efficient coupling. These findings suggest that integrating rare-earth ion-based molecular complexes with photonic structures could be a viable approach for regulating their emission characteristics for particular applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Spectral widths and Stokes shifts in InP-based quantum dots

InP-based quantum dots (QDs) have Stokes shifts and photoluminescence (PL) line widths that are larger than in II–VI semiconductor QDs with comparable exciton energies. The mechanisms responsible for these spectral characteristics are investigated in this paper. Upon comparing different semiconductors, we find the Stokes shift decreases in the following order: InP > CdTe > CdSe. We also find that the Stokes shift decreases with core size and decreases upon deposition of a ZnSe shell. We suggest that the Stokes shift is largely due to different absorption and luminescent states in the angular momentum fine structure. The energy difference between the fine structure levels, and hence the Stokes shifts, are controlled by the electron–hole exchange interaction. Luminescence polarization results are reported and are consistent with this assignment. Spectral widths are controlled by the extent of homogeneous and inhomogeneous broadening. Here, we report PL and PL excitation (PLE) spectra that facilitate assessing the roles of homogeneous and different inhomogeneous broadening mechanisms in the spectra of zinc-treated InP and InP/ZnSe/ZnS particles. There are two distinct types of inhomogeneous broadening: size inhomogeneity and core–shell interface inhomogeneity. The latter results in a distribution of core–shell band offsets and is caused by interfacial dipoles associated with In–Se or P–Zn bonding. Quantitative modeling of the spectra shows that the offset inhomogeneity is comparable to but somewhat smaller than the size inhomogeneity. The combination of these two types of inhomogeneity also explains several aspects of reversible hole trapping dynamics involving localized In 3+ /V Zn 2– impurity states in the ZnSe shells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗