Search NASA⌕ Search

SEARCH · Search NASA

Results for “Powder Removal”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

161 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Air separation via two-step solar thermochemical cycles based on SrFeO 3-δ and (Ba,La) 0.15 Sr 0.85 FeO 3-δ perovskite reduction/oxidation reactions to produce N 2 : rate limiting mechanism(s) determination

Two-step solar thermochemical cycles based on reversible reactions of SrFeO 3–δ and (Ba,La) 0.15 Sr 0.85 FeO 3–δ perovskites were considered for air separation. The cycle steps encompass (1) the thermal reduction of SrFeO 3–δ or (Ba,La) 0.15 Sr 0.85 FeO 3–δ perovskites driven by concentrated solar irradiation and (2) oxidation in air to remove O 2 and produce N 2 . Rate limiting mechanisms were examined for both reactions using a combination of isothermal and non-isothermal thermogravimetry for temperature-swings between 673 and 1373 K, heating rates of 10, 20, and 50 K min –1 , and O 2 pressure-swings between 20% O 2 /Ar and 100% Ar at atmospheric pressure. Evolved O 2 and associated lag due to transport behavior were measured with gas chromatography and used with measured sample temperatures to predict equilibrium compositions from a compound energy formalism thermodynamic model. Measured and predicted chemical equilibrium changes in deviation from stoichiometry were compared. Rapid chemical kinetics were observed as the samples equilibrated rapidly for all conditions, indicative that heat and mass transfer were the rate limiting mechanisms. Furthermore, the effects of bulk diffusion (or gas diffusion through the bed or pellet) were examined using pelletized and loose powdered samples and determined to have no discernable impact.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

INFLUENCE OF SUPPLEMENTARY ARGON GAS SHIELDING ON THE MICROSTRUCTURE AND MECHANICAL BEHAVIOR OF SS316L ADDITIVELY MANUFACTURED BY DIRECTED ENERGY DEPOSITION

The dissolution of atmospheric gases into parts additively manufactured by directed energy deposition (DED) has long been of concern, and stock shielding solutions have usually proven inadequate at fully removing atmospheric gases from weld beads. The objective of this work was to design a new supplementary argon gas shroud for a specific DED printer and evaluate its effect on microstructure and macroscopic properties of SS316L and the potential for printing more reactive metals such as Ti-6Al-4V. This was investigated by printing four SS316L sample blocks, two with and two without the shroud, each printed in two different orientations. These samples were subsequently evaluated with inert gas fusion (IGF), SEM/EDS imaging, and tensile tests. The shroud reduced oxygen content by 0.019-0.031%, and SEM imaging revealed fewer oxide inclusions. A more dramatic reduction of 0.13% oxygen and 0.171% nitrogen was observed by the inert gas fusion of Ti-6Al-4V samples. Overall, the results indicated the shroud was successful at reducing atmospheric gas uptake within the print region and may enable the printing of reactive metal powders in DED systems.

Helvie, Kyle↗
DOE OSTI2026

Probing Terra Incognita of Ni–P Catalysts: Operando Explorations during Hydrogen Evolution Reaction

We have developed two Ni phosphide preparation methods allowing operando XAS surface-sensitive studies of well-defined bulk systems. For Ni K-edge XAS, a Ni 2 P phase-pure powder was sintered into a high-density pellet and polished for grazing incidence XAS. Ni sites were mildly affected by the acidic electrolyte prior to the HER, while the applied cathodic potential caused the reduction of Ni surface states beyond the states of as-prepared Ni 2 P. The computed fully H-covered Ni 2 P [0001] model describes the difference in the operando Ni K-edge GIXAS spectrum well. Upon turning the applied bias off, the Ni sites became immediately oxidized, forming NiO on the surface. Thus, the active phase during the HER is covalent Ni 0 close to that in the intermetallic phosphides, and Ni 2+ oxides formed after, and not during, the HER. For P K-edge XAS, Ni foam was phosphorized to form a thin Ni 3 P layer while preserving its high surface area. Upon immersion in the acidic electrolyte, the P sites underwent removal of P 5+ phosphates and formed new P coordination, possibly due to the adsorption of protons from the electrolyte. These new P surface states were not affected by turning the cathodic current on and off as soon as the sample was immersed in the acidic electrolyte. However, the removal of the sample from the electrochemical cell and drying in air resulted in substantial depletion and oxidation of surface P. Echoing the observed Ni site chemistry during HER, XAS and XPS suggest that the in situ active P sites are different from the oxidized P states observed under ex situ conditions.

Kong, Seongyoung [Iowa State Univ., Ames, IA (Unit↗
DOE OSTI2025

Protection and enrichment: how two different carbonaceous biofilm supports improve methane yield from encapsulated anaerobic microorganisms

Encapsulating anaerobic microorganisms allows for the separation of the solids retention time from the hydraulic retention time during anaerobic wastewater treatment. The harsh chemistries involved in the process of encapsulation can have adverse effects on microorganisms for anaerobic digestion, especially methanogens, and can lead to lower methane yields after encapsulation. Improving the survival and maintaining activity of anaerobic communities during encapsulation will likely be the key to improving methane yield. In this study, we investigated the encapsulation of biomass grown as biofilms on two carbonaceous materials, biochar and powdered activated carbon (PAC), to improve methane yield. Microorganisms grown as biofilms on biochar and PAC were encapsulated in polyethylene glycol (PEG) and incubated for 10 days. After 10 days, the unamended control capsules produced 81.6 ± 5.4 μmol of methane, while PAC-amended capsules produced 129.8 ± 1.9 μmol and biochar-amended capsules produced 432.96 ± 20.8 μmol methane, with the differences being statistically significant (p < 0.05). In biochar, a higher relative abundance of methanogens led to increased methane production capacity. The ratio of the methyl coenzyme M reductase (mcrA) genes to total 16S rRNA genes in the encapsulated biochar-supported biofilms was significantly higher than that in the encapsulated unsupported (p = 4.9 × 10 −5 ) and the PAC-supported biofilms (p = 0.012). Biochar-supported biofilms also had higher methane output per mcrA or 16S rRNA gene copy number. For the PAC, biofilms were protected from ammonium persulfate (APS), a powerful oxidant used in the encapsulation process. PAC removed 92% of dissolved APS, reducing exposure of the methanogens to this chemical. Unfortunately, this removal of APS compromised capsule stability, limiting the amount of PAC that could be added to the capsules. Furthermore, amendments that improve survival and activity of methanogens should be used in the capsules instead of those that protect methanogens by interfering with encapsulant polymerization chemistry.

Resource recovery↗
DOE OSTI2020

Major element composition controls rare earth element solubility during leaching of coal fly ash and coal by-products

Coal combustion ash and pre-combustion coal refuse are currently under consideration as potential sources of rare earth elements. One of the early steps in recovering REEs from coal by-products is often acid leaching, which can result in low pH leachates with complex aqueous chemistry. The aim of this work was to understand the connection between REE solubility, pH, and major elemental components of leachates for coal by-products. To accomplish this, we investigated the effects of solids concentration (i.e., pulp density) and pH adjustment on REE solubility in acid leachates of coal fly ashes from the Powder River Basin (PRB) and Appalachian Basin in the United States, and a coal processing refuse from the Southwestern U.S. For PRB ashes, the concentrations of soluble REEs generally increased with increasing pulp density; however, at pulp density values above 80–100 g/L, the soluble REE concentrations in the leachates were markedly lower. Similarly, the soluble concentrations of other major solutes (Fe, Al, Si) that leached from PRB fly ashes were also non-linear with pulp density. These major elements tended to reach maximum concentration values at 60–70 g/L pulp density. In contrast, for the Appalachian fly ashes and the coal by-product, soluble concentrations of REE and major elements in leachates increased linearly with pulp density. Chemical equilibria calculations of mineral saturation indices indicated that trends in soluble REE concentrations could be explained by saturation conditions for Fe and Al-(hydr)oxides and possibly sulfate minerals, but not lanthanide hydroxides. Furthermore, pH adjustment of the acid leachates showed that REEs and many major solutes were removed from solution at pH values above 4.5, also consistent with Fe- and Al-(hydr)oxide precipitation. These results highlight the importance of understanding the chemical composition of leachates when designing REE recovery processes for low-grade geologic feedstocks and that precipitation of hydr(oxide) or sulfate minerals of major elements rather than discreet formation of REE mineral phases could be used for process optimization.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2020

Pulsed Thermal Tomography Nondestructive Examination of Additively Manufactured Reactor Materials (Second Annual Progress Report)

Additive manufacturing (AM) is an emerging method for cost-efficient fabrication of nuclear reactor parts. AM of metallic structures for nuclear energy applications is currently based on laser powder bed fusion (LPBF) process, which can introduce internal material flaws, such as pores and anisotropy. Integrity of AM structures needs to be evaluated nondestructively because material flaws could lead to premature failures due to exposure to high temperature, radiation and corrosive environment in a nuclear reactor. Thermal tomography (TT) provides a capability for non-destructive evaluation of sub-surface defects in arbitrary size structures. Thermal tomography is a computational method for heat diffusion-based imaging of solids, which provides 3D visualization of data from flash thermography measurements. We investigate thermal tomography imaging and nondestructive evaluation of stainless steel and nickel super alloy metallic structures produced with laser powder bed fusion (LPBF) additive manufacturing (AM) process. Metallic structures produced with LPBF contain defects, and there are limited capabilities to evaluate these structures non-destructively. Thermal tomography reconstruction of 3D apparent spatial effusivity provides information about AM structure geometry and internal material flaws. We study performance of thermal tomography in imaging of metallic structures through COMSOL computer simulations of transient heat transfer, and through reconstruction of data obtained from experimental measurements. Reconstruction of internal defects is investigated using a stainless steel 316L specimen with flat bottom hole (FBH) indentations, and Inconel 718 plate produced with laser powder bed fusion (LPBF) method, which contains imprinted hemispherical shape low density regions containing non-sintered metallic powder. The FBH’s have the same sizes as the imprinted defects in the LPBF specimens, but offer better imaging contrast. Thermal tomography reconstructions provide visualizations of internal defects, and allow for estimation of their sizes and locations. Detection sensitivity of TT is limited by noises. We investigate separation of signal from noise in thermography images using several machine learning (ML) methods, including new spatio-temporal blind source separation (STBSS) and spatio-temporal sparse dictionary learning (STSDL) methods. Performance of the ML methods is benchmarked using thermography data obtained from imaging stainless steel 316L and Inconel 718 specimens produced LPBF method with imprinted calibrated porosity defects. The ML methods are ranked by F-score and execution runtime. Finally, we investigate TT of AM stainless steel 316L specimen with imprinted internal porosity defects using relatively low-cost, small form factor infrared (IR) camera based on uncooled micro bolometer detector. Sparse coding related K-means singular value decomposition (SVD) machine learning, image processing algorithms are developed to improve quality of TT images through removal of Additive white Gaussian noise without blurring the images. Following initial qualification of an AM component for deployment in a nuclear reactor, a compact TT can also be used for in-service nondestructive evaluation (NDE). With capability to perform in-service NDE of the AM component lifecycle, TT data can be used for development of a component digital twin.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

The Impact of Structural Distortions on the Magnetism of Double Perovskites Containing 5d 1 Transition-Metal Ions

Five double perovskites, each containing a transition-metal ion with a 5d 1 configuration, have been studied to better understand the surprising diversity of magnetic ground states seen in these isoelectronic compounds. Ba 2 ZnReO 6 adopts the cubic double perovskite structure and magnetically orders below 16 K, with a canted ferromagnetic structure and a saturated magnetization of ~0.24 μ B /Re. X-ray magnetic circular dichroism indicates a substantial orbital moment of approximately 0.4 μ B /Re that opposes the spin moment. The structures of Ba 2 NaOsO 6 (canted ferromagnet, T C = 7 K) and Ba 2 LiOsO 6 (antiferromagnet, T N = 8 K) are reinvestigated using time-of-flight neutron powder diffraction and found to crystallize with the cubic double perovskite structure. No evidence for a structural distortion can be found in either compound down to 10 K. Ba 2 CdReO 6 is also cubic at room temperature but undergoes a structural transition upon cooling below ~180 K to a tetragonal structure with I4/m symmetry that involves compression of the Re–O bonds that are parallel to the c-axis. Sr 2 LiOsO 6 shows a similar tetragonal distortion at room temperature and maintains that structure down to 10 K. Surprisingly, the Os-centered octahedron in Sr 2 LiOsO 6 is distorted in the opposite direction, exhibiting an elongation of the Os–O bonds along the c-axis. Differences in the distortions of the octahedra lead to different magnetic ground states, antiferromagnetic (T N = 4 K) for Ba 2 CdReO 6 and spin glass (T g = 30 K) for Sr 2 LiOsO 6 . Theoretical modeling shows that the varied magnetic behaviors of double perovskites containing 5d 1 ions are closely tied to crystallographic distortions. Furthermore, these distortions remove the degeneracy of the 5d t 2g orbitals, leading to changes in orbital occupation that ultimately determine which of the several competing magnetic ground states is favored.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Probabilistic Analysis of Long-Term Degradation of Microwave Cavity Flow Sensor

We are investigating a microwave resonant cavity transducer for flow sensing in the vessel of a high temperature fluid advanced reactor (AR), such as a molten salt cooled reactor (MSCR) or a sodium fast reactor (SFR). This transducer is a hollow metallic cylindrical cavity, with the flat wall of the cylinder flexible enough to undergo microscopic deflection due to dynamic fluid pressure. Membrane deflection leads to a shift in the resonant frequency, which can be detected with a spectrum analyzer. We have performed a proof-of-concept experiment of flow sensing with the transducer in liquid sodium at 340°C in impinging liquid jet geometry. The transducer remained in liquid sodium for 70 days. After removal, no structural damage was observed, and the expected transducer response was verified in a water test. Because long-term (multi-year) experimental tests of transducer resilience to harsh environment are not practical, we have developed a probabilistic model of creep to estimate transducer resilience to the harsh environment. The probabilistic model considers diffusion creep under the condition of high temperature and low stress, where the stress and temperature are allowed to be random variables with Gaussian distributions. Using the probabilistic model, we estimate inelastic membrane deflections due to creep for several temperature ranges. We conclude that for temperatures less than 650°C, creep has negligible long-term effect on the transducer performance. Since a yellowish residue was observed on the transducer surface after 70 days of immersion in liquid sodium, we have investigated possible evidence of corrosion. Chromium depletion is a typical indicator of the corrosion process in stainless steel. Scraping off a residue from the transducer and performing scanning electron microscopy (SEM) with energy dispersive analysis (EDS) did not find any chromium in the residue. Approximately 60% of the residue consisted of copper, which can be attributed to contamination of sodium due to powder residue from machining of copper and brass components of the transducer.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Iodine Capture Studies of Silver Mordenite and Novel Alternative Metal Sorbents

Radioiodine is one of the radionuclides of concern when considering reprocessing of used nuclear fuel (UNF). It is expected to be released primarily in the dissolver off-gas (DOG) stream. Sorbents that target I 2 removal from a UNF processing off gas must perform efficiently under elevated temperatures in the presence of water vapor and nitrogen oxide gasses (NOx). Many studies have been conducted that examine the adsorption of iodine species in the presence of NOx gases through reduced silver-exchanged mordenite (Ag 0 Z), a zeolite mineral. This study characterizes the effects of iodine, water vapor, and nitrogen dioxide on the adsorption of I 2 by Ag 0 Z at lower temperatures suitable for comparison with novel Cu- and Bi- bearing sorbents which offer a non-RCRA alternative. When exposed to ‘harsh’ conditions such as I 2 , H 2 O, and NO 2 vapors carried by air, Cu 2 S-polyacrylonitrile (PAN) is more efficient than Ag 0 Z and all other novel sorbents, providing with 11% I capture efficiency. However, under ‘ideal’ conditions in which I 2 is carried by dry air), Ag 0 Z is more efficient than Cu 2 S-PAN and other novel sorbents, providing 74% I capture efficiency. To investigate this result and the overall performance of all sorbents tested, several characterization techniques were employed, including thermal gravimetric analysis, scanning electron microscopy – electron dispersion X-Ray spectroscopy, powder X-ray diffraction, and X-ray photoelectron spectroscopy. These techniques are discussed within this report. This document also includes a design and test plan update from Idaho National Laboratory as the next step in testing the high performing sorbents from thin-bed tests carried out by Oak Ridge National Laboratory.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Modified Isotherm Modeling to Predict Cs Exchange with Crystalline Silicotitanate in Tank Waste Simulants

The U.S. Department of Energy is working to expedite processing of Hanford tank waste supernate at the Hanford Waste Treatment and Immobilization Plant. To support this goal, Washington River Protection Solutions is designing a Tank Side Cesium Removal (TSCR) system for suspended solids and cesium (Cs/ 137 Cs) removal from Hanford tank waste supernate. The ion exchange media selected for Cs removal at TSCR is crystalline silicotitanate (CST) that is manufactured in a nearly spherical form by Honeywell UOP LLC (UOP; Des Plaines, IL) as product IONSIV® R9140-B (Na form). The Zheng Anthony Miller (ZAM) isotherm model (Zheng et al. 1997) is a multicomponent ion exchange model used to predict the exchange of Group I metals onto CST. The ZAM isotherm has historically been used to predict Cs distribution values from Hanford and Savannah River Site (SRS) tank waste simulants. Figure S.1 summarizes model predictions from the ZAM isotherm that indicate poor prediction of Cs distribution values for simple and complex simulants with the engineered form of CST, IONSIV® R9140-B, and IONSIV® R9120-B where the solid line indicates a perfect fit by the model. The dotted lines indicate ±20% error. Batch contact testing with Hanford tank waste complex and simple simulants was used in conjunction with SRS simulants to experimentally determine Cs distribution values using a modification to the original isotherm model. The experimentally determined maximum Cs capacity for IONSIV® R9140-B CST in both the simple and complex matrices was found to be 0.53±0.3 mmoles Cs/g of CST. This value is not drastically different from the maximum Cs capacity of 0.58 mmoles Cs/g TAM-5 reported by Zheng et al. (1997). However, it is important to note that TAM-5 (commercially IONSIV® IE-910) is a powder. Hamm et al. (2002) determined that a dilution factor was needed to account for the Zr(OH)2 binder in the engineered form of CST. Hamm et al. determined that a dilution factor of 0.68 was appropriate to account for binder contribution and correct overprediction of Cs exchange on the engineered form of CST in ZAM calculations. This reduced the total capacity from 0.58 mmol/g with TAM-5 to 0.39 mmol/g for the engineered form of CST (Hamm et al. 2002). Despite substituting the experimentally determined maximum Cs capacity of 0.55 mmoles Cs/g for the literature-reported capacity of 0.39 mmoles Cs/g, it was determined that additional modifications to the model’s equilibrium rate constants were necessary in refining the isotherm model. The modified model overpredicted K+ uptake by the CST when compared to digested CST results described by Campbell et al. (2019). The modified model was further revised to omit three of the five K+ exchange equilibrium reactions described by ZAM to reduce the additional K+ loading seen by the model. Figure S.2 summarizes the revised model isotherm predictions plotted against measured Kd values.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

L-PBF High-Throughput Data Pipeline Approach for Multi-modal Integration

Abstract Metal-based additive manufacturing requires active monitoring solutions for assessing part quality. Multiple sensors and data streams, however, generate large heterogeneous data sets that are impractical for manual assessment and characterization. In this work, an automated pipeline is developed that enables feature extraction from high-speed camera video and multi-modal data analysis. The framework removes the need for manual assessment through the utilization of deep learning techniques and training models in a weakly supervised paradigm. We demonstrate this pipeline’s capability over 700,000 high-speed camera frames. The pipeline successfully extracts melt pool and spatter geometries and links them to corresponding pyrometry, radiography, and processparameter information. 715 individual prints are examined to reveal melt pool areas that exceeds 0.07 mm 2 and pyrometry signal over a threshold (375 pyrometry units) were more likely to have defects. These automated processes enable massive throughput of characterization techniques.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Material and component developments for the DEMO divertor using fibre reinforcement and additive manufacturing

Within the research along the European Fusion Roadmap, water-cooled divertor PFCs are foreseen in the design of a first fusion demonstration power plant (DEMO) in order to provide reliable heat removal capability. In the frame of this concerted attempt, the Max Planck Institute for Plasma Physics is concentrating on the development and testing of composite materials based on tungsten (W, preferred armour material) and copper (Cu, preferred heat sink material). W fibres (W f ) as monofilaments and yarns as reinforcement play a central role in these investigations due to their extraordinary properties concerning ductility already at room temperature and high tensile strength. Recent investigations on the impact of radiation damage suggest that the fibres retain their ductility upon irradiation. W reinforced with W fibres (W f /W) allows to overcome the intrinsic brittleness of W. Quantitative mechanical fracture tests of W f /W confirm the basic mechanisms of fibre reinforcement and the increased resistance to mechanical fatigue. The good wettability of W with liquid Cu and the absence of any metallurgical solubility make up an ideal material pairing for composite production. W fibre-reinforced Cu (W f /Cu) cooling tubes provide a rather high thermal conductivity (> 250 W mK -1 ) and at least twice the strength of CuCrZr in hoop direction in the temperature range up to at least 500 °C. Very recent neutron irradiation experiments confirm the sustainment of ductility of the W f /Cu composite. Numerical simulations suggest that thermal stresses in W-Cu PFCs could be strongly reduced by tailoring the local W and Cu volume fraction. This 'freely' distributed material composition can be achieved by means of additively manufactured W skeletons consecutively infiltrated by Cu. Investigations with W preforms produced by Laser Beam Powder Bed Fusion and infiltrated by Cu demonstrate the feasibility of this approach while testing of specifically prepared specimen is ongoing.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Gasification of Coal and Biomass: The Route to Net-Negative-Carbon Power and Hydrogen

One promising process that is a candidate for meeting the goals of the US Department of Energy’s 21st Century Power Plant initiative is to gasify a mixture of coal and biomass to yield a syngas, which can have CO2 removed and then be used to produce hydrogen as well as an off-gas that can be used to flexibly produce power. This concept would overall be carbon net-negative and readily meet the 21st Century Power Plant initiative targets of smaller scale MW generation, high ramp rates and turndown, feedstock flexibility, and high efficiency—at a reasonable cost. Moreover, adding the large-scale production of “ultra-green” hydrogen yields a system tailored for the coming hydrogen economy, providing long-term energy storage and an attractive co-product for sale. The objective of the work being led by the Electric Power Research Institute, Inc. (EPRI), with support by Bechtel Corporation (Bechtel), Gas Technology Institute (GTI), Hamilton Mauer International, Inc. (HMI), Nebraska Public Power District (NPPD), NexantECA, Inc. (Nexant), and Wärtsilä, is to perform a front-end design and engineering (FEED) study on an oxygen-blown gasification system coupled with water-gas shift, pre-combustion CO2 capture, and pressure-swing adsorption working off a coal/biomass mix to yield high-purity hydrogen and a fuel off-gas that can generate power. Several designs are being considered that will be capable of producing 50 MW net from a flexible generator, over 8500 kg/hr of hydrogen, and net-negative CO2 emissions, at an efficiency of 50% net HHV. The plant would be hosted at an NPPD site, where opportunities for enhanced oil recovery and sequestration have been investigated and the need for low-carbon power and hydrogen is imminent. The principal biomass to be used is corn stover—prevalent in Nebraska where the plant will be located—mixed with Powder River Basin (PRB) coal, necessitating a gasifier that can use this feedstock and be flexible to allow other types. Waste plastics will also be reviewed for use. Two oxygen-blown gasifiers have been identified as candidates that have done testing with biomass including corn stover: the GTI gasifier—a high-pressure, fluidized-bed type—and HMI’s, a lower pressure moving-bed type. Both have relative advantages that are being investigated in the Phase I design study, with a resultant down select of one system for which the FEED will be performed in Phase II. The technical tasks for the proposed project are: • Design Development: Completion of design activities necessary to provide inputs for the FEED study. Multiple design cases will be assessed with the selection of the optimal one for the FEED. • Investment Case Preparation: Development of the draft investment case for the proposed process with business cases performed for the proposed host site and two other locations. • Host Site Selection: Evaluation of the two potential host sites within NPPD’s portfolio to select the preferred candidate based on technical, economic, and environmental considerations. • Environmental Information Volume (EIV) Development: Completion of the EIV for the host site. • FEED Study: Completion of a FEED study based on the design selected in Phase I. A Greenhouse Gas Life Cycle Analysis will also be performed for the process. • Update Investment Case: Finalization of the investment case based on findings from the FEED. The advantages of the proposed project are significant. Having an engaged U.S. power utility willing to provide a host site that will produce energy from coal plus a deep and experienced team is critical; the process meets all the goals of DOE’s 21st Century Power Plant initiative at an estimated total plant cost of ~$880M and a production cost of hydrogen of ~$2/kg-H2 while producing net-negative carbon power. If developed, this process has real commercial potential in the United States—supported by EPRI’s initial review of the considerable interest from selected U.S. utilities—and elsewhere around the globe. The process has fewer environmental hurdles compared to other concepts, lowering regulatory and protest risks—providing a pathway to preserving the viability of a critical indigenous energy source by transforming its use to match a changing world. This presentation will outline the motivation for the effort, summarize project plans, work completed to date, results of the Design Development task, and detailed work scope for the remainder of the project.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2023

Gasification of Coal and Biomass: The Route to Net-Negative-Carbon Power and Hydrogen

One promising process that is a candidate for meeting the goals of the US Department of Energy’s 21st Century Power Plant initiative is to gasify a mixture of coal and biomass to yield a syngas, which can have CO2 removed and then be used to produce hydrogen as well as an off-gas that can be used to flexibly produce power. This concept would overall be carbon net-negative and readily meet the 21st Century Power Plant initiative targets of smaller scale MW generation, high ramp rates and turndown, feedstock flexibility, and high efficiency—at a reasonable cost. Moreover, adding the large-scale production of “ultra-green” hydrogen yields a system tailored for the coming hydrogen economy, providing long-term energy storage and an attractive co-product for sale. The objective of the work being led by the Electric Power Research Institute, Inc. (EPRI), with support by Bechtel Corporation (Bechtel), Gas Technology Institute (GTI), Hamilton Mauer International, Inc. (HMI), Nebraska Public Power District (NPPD), NexantECA, Inc. (Nexant), and Wärtsilä, is to perform a front-end design and engineering (FEED) study on an oxygen-blown gasification system coupled with water-gas shift, pre-combustion CO2 capture, and pressure-swing adsorption working off a coal/biomass mix to yield high-purity hydrogen and a fuel off-gas that can generate power. Several designs are being considered that will be capable of producing 50 MW net from a flexible generator, over 8500 kg/hr of hydrogen, and net-negative CO2 emissions, at an efficiency of 50% net HHV. The plant would be hosted at an NPPD site, where opportunities for enhanced oil recovery and sequestration have been investigated and the need for low-carbon power and hydrogen is imminent. The principal biomass to be used is corn stover—prevalent in Nebraska where the plant will be located—mixed with Powder River Basin (PRB) coal, necessitating a gasifier that can use this feedstock and be flexible to allow other types. Waste plastics will also be reviewed for use. Two oxygen-blown gasifiers have been identified as candidates that have done testing with biomass including corn stover: the GTI gasifier—a high-pressure, fluidized-bed type—and HMI’s, a lower pressure moving-bed type. Both have relative advantages that were investigated in the Phase I design study, with a resultant down select of one system for which the FEED will be performed in Phase II. The technical tasks for the project are: • Design Development: Completion of design activities necessary to provide inputs for the FEED study. Multiple design cases will be assessed with the selection of the optimal one for the FEED. • Investment Case Preparation: Development of the draft investment case for the proposed process with business cases performed for the proposed host site and two other locations. • Host Site Selection: Evaluation of the two potential host sites within NPPD’s portfolio to select the preferred candidate based on technical, economic, and environmental considerations. • Environmental Information Volume (EIV) Development: Completion of the EIV for the host site. • FEED Study: Completion of a FEED study based on the design selected in Phase I. A Greenhouse Gas Life Cycle Analysis will also be performed for the process. • Update Investment Case: Finalization of the investment case based on findings from the FEED. The advantages of the proposed project are significant. Having an engaged U.S. power utility willing to provide a host site that will produce energy from coal plus a deep and experienced team is critical; the process meets all the goals of DOE’s 21st Century Power Plant initiative at an estimated total plant cost of ~$880M and a production cost of hydrogen of ~$2/kg-H2 while producing net-negative carbon power. If developed, this process has real commercial potential in the United States—supported by EPRI’s initial review of the considerable interest from selected U.S. utilities—and elsewhere around the globe. The process has fewer environmental hurdles compared to other concepts, lowering regulatory and protest risks—providing a pathway to preserving the viability of a critical indigenous energy source by transforming its use to match a changing world. This presentation outlines the motivation for the effort, summarizes project plans, work completed to date, results of the Phase I effort and, and detailed work scope for the remainder of the project in the Phase II FEED effort.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2021

Performance of Compact Pulsed Thermal Imaging System for In-Service Applications. Pulsed thermal tomography nondestructive examination of additively manufactured reactor materials and components

Additive manufacturing (AM) is an emerging method for cost-efficient fabrication of complex topology nuclear reactor parts from high-strength corrosion resistance alloys, such as stainless steel and Inconel. AM of metallic structures for nuclear energy applications is currently based on laser powder bed fusion (LPBF) process, which has the capability of melting metallic powder and net shaping the structures with relatively high precision. Some of the challenges with using LPBF method for nuclear manufacturing include the possibility of introducing pores into metallic structures. Integrity of AM structures needs to be evaluated nondestructively because material flaws could lead to premature failures due to creep in high temperature nuclear reactor environment. Currently, there exist limited capabilities to evaluate actual AM structures nondestructively. Pulsed Thermography (PT) imaging provides a capability for non-destructive evaluation (NDE) of sub-surface defects in arbitrary size structures. The PT method is based on recording material surface temperature transients with infrared (IR) camera following thermal pulse delivered on material surface with flash light. The PT method has advantages for NDE of actual AM structures because the method involves one-sided non-contact measurements and fast processing of large sample areas captured in one image. The data cube of PT measurements consists of surface temperature taken at sequential time intervals T(x,y,t). Material defects can be detected either by analyzing the thermograms T(x,y,t) data cube, or by using thermal tomography (TT) algorithm to obtain 3D spatial reconstruction of thermal effusivity e(x,y,z). To reduce the cost and enable in-service NDE in spatially constrained environment, it is highly desirable to develop PT with compact and inexpensive IR camera. Following initial qualification of an AM component for deployment in a nuclear reactor, a compact PT system can also be used for in-service nondestructive evaluation (NDE) applications. However, data cube obtained with PT based on compact IR camera suffers from strong thermal noises and loss of features due to relatively low sampling rate. In this report we describe two unsupervised machine learning (ML) algorithms for enhancement of PT images obtained with compact IR camera. In one approach, we introduce Sparse Coding Discrete Cosine Transform (SC/DCT) algorithm to remove additive white Gaussian noise (AWGN) from spatial thermal effusivity reconstructions. In another approach we introduce a Spatial Temporal Denoised Thermal Source Separation (STDTSS) ML algorithm to process thermograms. The STDTSS algorithm consists of spatial and temporal denoising using Gaussian and Savitzky–Golay filtering, followed by the matrix decomposition using Principal Component Analysis (PCA), and Independent Component Analysis (ICA) to automatically detect flaws. In the work described in this report, we constructed a compact PT system using a relatively small and low-cost FLIR A65 camera, consisting on uncooled microbolometer detector. Performance of SC/DCT algorithm was demonstrated on enhancing TT images of Inconel 718 AM plate. Performance of the STDTSS methods was investigated using thermography data obtained from imaging stainless steel 316L specimens produced with LPBF method with imprinted calibrated porosity defects.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Machining of Thin-Walled Structures From Stiffness-Driven Additively Manufactured Preform Geometry

Additive manufacturing provides the means to build component preforms with reduced excess material to create functional parts. In the case of aero-structural and aero-engine components, additive manufacturing technologies offer the possibility to substantially reduce the volume of material to be removed by machining operations. To achieve this objective, the preform must be built with the minimum material necessary to contain the final geometry and simultaneously provide enough stiffness to withstand the magnitude of the machining forces. This work describes a computationally efficient method to calculate the geometry required from the preform to reliably manufacture typical thin-walled structures via finish machining processes. This is achieved by defining the preform with near constant static stiffness across the width of the preform, in combination with a prescribed magnitude of stiffness at the top edge of the preform. The prescribed static stiffness is the function of the machining force magnitude, a direct consequence of the preselected cutting conditions. In conclusion, this article illustrates the application of the method to a straight single boundary thin-walled structure as an introduction case and for ease of description.

Additive manufacturing↗
DOE OSTI2022

Uranium Oxide Elutriation at Higher Flow Rates and Longer Times

This work supports the recovery of high-assay low-enriched uranium (i.e., U enriched in 235 U to >5% and <20%) from used nuclear fuel. One step includes elutriating triuranium octoxide (U 3 O 8 ) from a fluidized bed of alumina (Al 2 O 3 ) that fills the main reaction chamber. The experiments outlined in this report assessed the effects of the time and flow rate on the elutriation of U 3 O 8 powder from the reaction vessel. Testing at Oak Ridge National Laboratory (ORNL) was performed in a one-fourth scale experimental apparatus based on a pilot-scale system, which is the Material Recovery Pilot Plant (MRPP) at Idaho National Laboratory (INL). The experimental system comprises a supply of pressurized nitrogen (N 2 ), a gas heater, the reaction vessel, a knock-out pot, and a water trap where elutriated particles are collected for sampling. An Al 2 O 3 fluidized bed is contained within the reaction vessel. A bed of Al 2 O 3 with a nominal size of 180 µm and U 3 O 8 with a nominal size of 7 µm was fluidized at 2 different flow rates so the U 3 O 8 physically separated from the bed. The apparatus was simple and had no valves or sharp bends downstream from the reactor. The flow exited the reactor through a side port at the top. The flow passed through a knock-out vessel before the flow was passed through a bubbler to capture the U 3 O 8 . Seven tests were completed with U 3 O 8 using an elutriating gas of N 2 heated to 200°C. Tests were performed with bed loadings that comprise 25.0 g of U 3 O 8 , or 3.6 wt% of the bed mass. Except for one test performed at 12 SLPM, the gas flow rate through the bed for the other experiments was set at 10 SLPM as measured by the mass flow meter. Linear velocities through the bed were calculated as 28 and 34 cm/s, or 0.9 and 1.1 ft·s -1 . The duration of the tests ranged from 20 to 180 min, and one test had a flow cycled between 0 and 5 SLPM every 5 min for 40 min. The testing successfully demonstrated elutriation of U 3 O 8 from the fluidized bed as up to a 100% of the U 3 O 8 was transferred out of the bed. The removal of U 3 O 8 had a logarithmic dependence on flow rate. The design changes made the apparatus easier to clean, and the mass balances were better than those used in previous studies. Some elutriated Al 2 O 3 collected in the tubing that connected the reactor to the knock-out pot, but the amount of Al 2 O 3 was minimal for 10 SLPM. The flow at 12 SLPM showed considerable transport of Al 2 O 3 bed material into the reaction-vessel headspace and the transfer line to the knock-out pot.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗