Search NASA⌕ Search

SEARCH · Search NASA

Results for “Priming effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Broad-band gain in optically pumped S2

The broad fluorescence spectrum and Franck-Condon shift of the B-X system of S2 are exploited in broad-band-gain experiments using the absorption of 308-nm XeCl excimer radiation to pump the level (upsilon-prime = 4) in an S2 vapor with and without Ar. The fluorescence spectra are examined to determine the effects of gas collisions, and the intense near-UV and visible bands are attributed to the redistribution of the population among the upsilon-prime levels resulting from S2-Ar collisions. Broad-band gain is observed on the rare-gas relaxation bands (2,17) (about 475 nm) and (3,18) (480 nm), while absorption is found in the (0,6), (0,7), and (0,8) near-UV (about 360-380-nm) bands where a transient population cascading down the X-state manifold fills the lower levels. It is inferred from the achievement of gain over much of the S2 fluorescence bandwidth that nonselective pumping mechanisms like discharges, solar energy, or flashlamps can be used with S2 as the tunable, chemically stable 'dye'.

Epler, J. E.↗
NASA NTRS1998

Word-identification priming for ignored and attended words

Three experiments examined contributions of study phase awareness of word identity to subsequent word-identification priming by manipulating visual attention to words at study. In Experiment 1, word-identification priming was reduced for ignored relative to attended words, even though ignored words were identified sufficiently to produce negative priming in the study phase. Word-identification priming was also reduced after color naming relative to emotional valence rating (Experiment 2) or word reading (Experiment 3), even though an effect of emotional valence upon color naming (Experiment 2) indicated that words were identified at study. Thus, word-identification priming was reduced even when word identification occurred at study. Word-identification priming may depend on awareness of word identity at the time of study.

Mental Recall↗
NASA NTRS1990

Oligomerization reactions of deoxyribonucleotides on montmorillonite clay - The effect of mononucleotide structure, phosphate activation and montmorillonite composition on phosphodiester bond formation

The 2(prime)-d-5(prime)-GMP and 2(prime)-d-5(prime)-AMP bind 2 times more strongly to montmorillonite 22A than do 2(prime)-d-5(prime)-CMP and 5(prime)-TMP. The dinucleotide d(pG)2 forms in 9.2 percent yield and the cyclic dinucleotide c(dpG)2 in 5.4 percent yield in the reaction of 2(prime)-d-5(prime)-GMP with EDAC in the presence of montmorillonite 22A. The yield of dimers which contain the phosphodiester bond decreases as the reaction medium is changed from 0.2 M NaCl to a mixture of 0.2 M NaCl and 0.075 M MgCl2. A low yield of d(pA)2 was observed in the condensation reaction of 5(prime)-ImdpA on montmorillonite 22A. The yield of d(pA)2 obtained when EDAC is used as the condensing agent increases with increasing iron content of the Na(+)-montmorillonite used as catalyst. Evidence is presented which shows that the acidity of the Na(+)-montmorillonite is a necessary but not sufficient factor for the montmorillonite catalysis of phosphodiester bond formation.

Ferris, James P.↗
NASA NTRS1992

Radiative lifetimes of the CN (A 2 Pi i) electronic state

Radiative lifetimes have been measured for CN (A 2 Pi i v-prime = 2...7). Ground-state radicals formed in the 193 nm photolysis of C2N2 and ClCN were excited to A 2 Pi i v-prime = 2...7 vibrational levels. The decay was monitored by following the fluorescence. Cascading effects were eliminated by working at low pressures and monitoring emission from a single vibrational band. Quenching rates and zero-pressure radiative lifetimes were obtained from Stern-Volmer plots. The lifetimes are significantly lower than previous measurements and theoretical calculations for vibrational states v-prime over 2.

Lu, Richang↗
NASA NTRS1984

Factors which influence directional coarsening of Gamma prime during creep in nickel-base superalloy single crystals

Changes in the morphology of the gamma prime precipitate were examined as a function of time during creep at 982 C in 001 oriented single crystals of a Ni-Al-Mo-Ta superalloy. In this alloy, which has a large negative misfit of -0.80 pct., the gamma prime particles link together during creep to form platelets, or rafts, which are aligned with their broad faces perpendicular to the applied tensile axis. The effects of initial microstructure and alloy composition of raft development and creep properties were investigated. Directional coarsening of gamma prime begins during primary creep and continues well after the onset of second state creep. The thickness of the rafts remains constant up through the onset of tertiary creep a clear indication of the stability of the finely-spaced gamma/gamma prime lamellar structure. The thickness of the rafts which formed was equal to the initial gamma prime size which was present prior to testing. The single crystals with the finest gamma prime size exhibited the longest creep lives, because the resultant rafted structure had a larger number of gamma/gamma prime interfaces per unit volume of material. Reducing the Mo content by only 0.73 wt. pct. increased the creep life by a factor of three, because the precipitation of a third phase was eliminated.

Mackay, R. A.↗
NASA NTRS1984

Factors which influence directional coarsening of gamma-prime during creep in nickel-base superalloy single crystals

Changes in the morphology of the gamma prime precipitate were examined as a function of the time during creep at 982 C in 001 oriented single crystals of a Ni-Al-Mo-Ta superalloy. In this alloy, which has a large negative misfit of -0.80 pct., the gamma prime particles link together during creep to form platelets, or rafts, which are aligned with their broad faces perpendicular to the applied tensile axis. The effects of initial microstructure and alloy composition of raft development and creep properties were investigated. Directional coarsening of gamma prime begins during primary creep and continues well after the onset of second state creep. The thickness of the rafts remains constant up through the onset of tertiary creep, a clear indication of the stability of the finely-spaced gamma/gamma prime lamellar structure. The thickness of the rafts which formed was equal to the initial gamma prime size which was present prior to testing. The single crystals with the finest gamma prime size exhibited the longest creep lives, because the resultant rafted structure had a larger number of gamma/gamma prime interfaces per unit volume of material. Reducing the Mo content by only 0.73 wt. pct. increased the creep life by a factor of three, because the precipitation of a third phase was eliminated.

Mackay, R. A.↗
DOE OSTI2024

Evaluating the Effectiveness of a Detection and Deterrent System in Reducing Golden Eagle Fatalities at Operational Wind Facilities

The Renewable Energy Wildlife Institute (REWI) was appointed as the prime awardee of DOE award number DE-EE0007883 to lead a team of scientists, wind developers, and technology manufacturers toward the overarching goal of evaluating the effectiveness of the current DTBird system in minimizing the risk of golden eagles (Aquila chrysaetos) and other large soaring raptors from approaching the rotor-swept zone (RSZ) of operating wind turbines. As part of this goal, the team set out to 1) quantify the expected reduction in collision risk for golden eagles from operation of the detection and deterrence modules in a manner that supports the approach used by the U.S. Fish and Wildlife Service (USFWS) to assess and credit facility operators for their efforts to minimize predicted collision fatalities and 2) provide information to help improve the technology to maximize its effectiveness. DTBird is an automated detection and audio deterrent system created by the Spanish company Liquen, designed to discourage birds from entering the RSZ of spinning wind turbines. The system uses cameras to automatically detect airborne targets of interest, records each such event in an online database, and triggers a warning signal (loud sound) if the tracked object has moved close to the turbine. If the object moves even closer to the RSZ, a more aggressive dissuasion signal is broadcast. To meet our objectives, the team conducted a two-year experiment at the Goodnoe Hills wind facility in Washington state, in which 14 turbines were outfitted with DTBird units. Daily, each DTBird-equipped turbine was randomly assigned to a control or treatment group. Treatment turbines operated with DTBird running as intended—broadcasting warning or deterrent signals when DTBird detected a target within range. On control turbines, no sound signals were broadcast if a moving target triggered the DTBird system. The team also flew unmanned aerial vehicles (UAVs) designed to coarsely mimic the general size, weight, and coloration of golden eagles in programmed flight transects across DTBird detection ranges to quantify DTBird’s ability to detect intended targets and to evaluate factors that influence the probability of detection and DTBird’s response distances. Additionally, the team evaluated the behavioral responses of in situ eagles exposed to spinning turbines alone (visual and sound influences) versus spinning turbines plus broadcasted DTBird audio deterrents, to estimate the effectiveness of deterrence by the DTBird system. The data and results from these investigations were combined with those from a pilot study conducted at the Manzana Wind Power Project in California to better evaluate DTBird’s effectiveness across different landscapes.

17 WIND ENERGY↗
DOE OSTI2024

Elucidating the Role of InGaAs and InAlAs Buffers on Carrier Dynamics of Tensile-Strained Ge Double Heterostructures

Extensive research efforts of strained germanium (Ge) are currently underway due to its unique properties, namely, (i) possibility of band gap and strain engineering to achieve a direct band gap, thus exhibiting superior radiative properties, and (ii) higher electron and hole mobilities than Si for upcoming technology nodes. Realizing lasing structures is vital to leveraging the benefits of tensile-strained Ge (ε-Ge). Here, we use a combination of different analytical tools to elucidate the effect of the underlying InGaAs/InAlAs and InGaAs overlaying heterostructures on the material quality and strain state of ε-Ge grown by molecular beam epitaxy. Using X-ray analysis, we show the constancy of tensile strain in sub-50 nm ε-Ge in a quantum-well (QW) heterostructure. Further, effective carrier lifetime using photoconductive decay as a function of buffer type exhibited a high (low) defect-limited carrier lifetime of ~68 ns (~13 ns) in 0.61% (0.66%) ε-Ge grown on an InGaAs (InAlAs) buffer. These results correspond well with the measured surface roughness of 1.289 nm (6.303 nm), consistent with the surface effect of the ε-Ge/III–V heterointerface. Furthermore, a reasonably high effective lifetime of ~78 ns is demonstrated in a QW of ~30 nm 1.6% ε-Ge, a moderate reduction from ~99 ns in uncapped ε-Ge, alluding to the surface effect of the overlying heterointerface. Thus, the above results highlight the prime quality of ε-Ge that can be achieved via III–V heteroepitaxy and paves a path for integrated Ge photonics.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Doppler Boosted Dust Emission and Cosmic Infrared Background–Galaxy Cross-Correlations: A New Probe of Cosmology and Astrophysics

We identify a new cosmological signal, the Doppler-boosted Cosmic Infrared Background (DB-CIB), arising from the peculiar motion of the galaxies whose thermal dust emission source the cosmic infrared background (CIB). This new observable is an independent probe of the cosmic velocity field, highly analogous to the well-known kinematic Sunyaev-Zel'dovich (KSZ) effect. Interestingly, DB-CIB does not suffer from the "KSZ optical depth degeneracy", making it immune from the complex astrophysics of galaxy formation. We forecast that the DB CIB effect is detectable in the cross-correlation of CCAT-Prime and DESI-like experiments. Here,we show that it also acts as a new CMB foreground which can bias future KSZ cross-correlations, if not properly accounted for.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS1985

Lightning Protection for Composite Aircraft Structures

Lightning protection system consisting of two layers of aluminum foil separated by layer of dielectric material protects graphite/epoxy composite structures on aircraft. Protective layer is secondarily applied lightning protection system, prime advantage of which is nullification of thermal and right angle effect of lightning arc attachment to graphite/epoxy laminate.

Olson, G. O.↗
NASA NTRS1986

The effect of heat treatment on microfissuring in alloy 718

Changes in the microfissuring susceptibility of alloy 718 due to solution annealing and age hardening are studied. The effects of Ni3Nb (delta) precipitation during solution annealing and gamma-prime + gamma-double-prime precipitation during age hardening on microfissuring are investigated. It is observed that solution annealing reduces microfissuring and age hardening increases it, and the two precipitates do not affect microfissuring susceptibility. Potential causes for the detected intergranular segregation of the alloy are discussed.

Thompson, R. G.↗
NASA NTRS1994

Test results for rotordynamic coefficients of anti-swirl self-injection seals

Test results are presented for rotordynamic coefficients and leakage for three annular seals which use anti-swirl self-injection concept to yield significant improvement in whirl frequency ratios as compared to smooth and damper seals. A new anti-swirl self-inection mechanism is achieved by deliberately machining self-injection holes inside the seal stator mechanism which is used to achieve effective reduction of the tangential flow which is considered as a prime cause of rotor instability in high performance turbomachinery. Test results show that the self-injection mechanism significantly improves whirl frequency ratios; however, the leakage performance degrades due to the introduction of the self-injection mechanism. Through a series of the test program, an optimum anti-swirl self-injection seal which uses a labyrinth stator surface with anti-axial flow injections is selected to obtain a significant improvement in the whirl frequency ratio as compared to a damper seal, while showing moderate leakage performance. Best whirl frequency ratio is achieved by an anti-swirl self-injection seal of 12 holes anti-swirl and 6 degree anti-leakage injection with a labyrinth surface configuration. When compared to a damper seal, the optimum configuration outperforms the whirl frequency ratio by a factor of 2.

Kim, C. H.↗
NASA NTRS1984

Measurements of the thermal plasma environment of the Space Shuttle

The paper presents some initial results on measurements of the thermal plasma environment obtained by a spherical retarding potential analyzer and a Langmuir probe flown on (STS-3) as part of the NASA Office of Space Science-1 payload in March 1982. One of the major effects observed is a higher degree of turbulence in the ambient plasma compared to what is observed from similar instruments flown on unmanned satellites. In addition we see the temperature of the thermal electrons elevated to values of 4000-5000 K. Associated with elevated electron temperatures are regions of enhanced plasma density resulting from the appearance of high densities of molecular ions. The thermal plasma data also show clear effects of an induced V x B.L potential at the location of the probes which matches that produced by an L vector linking the probes to the engine nozzles; thereby establishing the prime return current location on the Orbiter. The final observations discussed are the pronounced and complex wake effects resulting both from the main structure of the Orbiter and from the complex shapes of appendages attached to the Orbiter.

Raitt, W. J.↗
NASA NTRS2004

New Effective Material Couple--Oxide Ceramic and Carbon Nanotube-- Developed for Aerospace Microsystem and Micromachine Technologies

The prime driving force for using microsystem and micromachine technologies in transport vehicles, such as spacecraft, aircraft, and automobiles, is to reduce the weight, power consumption, and volume of components and systems to lower costs and increase affordability and reliability. However, a number of specific issues need to be addressed with respect to using microsystems and micromachines in aerospace applications--such as the lack of understanding of material characteristics; methods for producing and testing the materials in small batches; the limited proven durability and lifetime of current microcomponents, packaging, and interconnections; a cultural change with respect to system designs; and the use of embedded software, which will require new product assurance guidelines. In regards to material characteristics, there are significant adhesion, friction, and wear issues in using microdevices. Because these issues are directly related to surface phenomena, they cannot be scaled down linearly and they become increasingly important as the devices become smaller. When microsystems have contacting surfaces in relative motion, the adhesion and friction affect performance, energy consumption, wear damage, maintenance, lifetime and catastrophic failure, and reliability. Ceramics, for the most part, do not have inherently good friction and wear properties. For example, coefficients of friction in excess of 0.7 have been reported for ceramics and ceramic composite materials. Under Alternate Fuels Foundation Technologies funding, two-phase oxide ceramics developed for superior high-temperature wear resistance in NASA's High Operating Temperature Propulsion Components (HOTPC) project and new two-layered carbon nanotube (CNT) coatings (CNT topcoat/iron bondcoat/quartz substrate) developed in NASA's Revolutionary Aeropropulsion Concepts (RAC) project have been chosen as a materials couple for aerospace applications, including micromachines, in the nanotechnology lubrication task because of their potential for superior friction and wearf properties in air and in an ultrahigh vacuum, spacelike environment. At the NASA Glenn Research Center, two-phase oxide ceramic eutectics, Al2O3/ZrO2(Y2O3), were directionally solidified using the laser-float-zone process, and carbon nanotubes were synthesized within a high-temperature tube furnace at 800 C. Physical vapor deposition was used to coat all quartz substrates with 5-nm-thick iron as catalyst and bondcoat, which formed iron islands resembling droplets and serving as catalyst particles on the quartz. A series of scanning electron micrographs showing multiwalled carbon nanotubes directionally grown as aligned "nanograss" on quartz is presented. Unidirectional sliding friction eperiments were conducted at Glenn with the two-layered CNT coatings in contact with the two-phase Al2O3/ZrO2(Y2O3) eutectics in air and in ultrachigh vacuum. The main criteria for judging the performance of the materials couple for solid lubrication and antistick applications in a space environment were the coefficient of friction and the wear resistance (reciprocal of wear rate), which had to be less than 0.2 and greater than 10(exp 5) N(raised dot)/cubic millimetes, respectively, in ultrahigh vacuum. In air, the coefficient of friction for the CNT coatings in contact with Al2O3/ZrO2 (Y2O3) eutectics was 0.04, one-fourth of that for quartz. In an ultrahigh vacuum, the coefficient of friction for CNT coatings in contact with Al2O3/ZrO2 (Y2O3) was one-third of that for quartz. The two-phase Al2O3/ZrO2 (Y2O3) eutectic coupled with the two-layered CNT coating met the coefficient of friction and wear resistance criteria both in air and in an ultrahigh vacuum, spacelike environment. This material's couple can dramatically improve the stiction (or adhesion), friction, and wear resistance of the contacting surfaces, which are major issues for microdevices and micromachines.

Miyoshi, Kazuhisa↗
NASA NTRS1990

Non-linear dynamic analysis of geared systems, part 2

A good understanding of the steady state dynamic behavior of a geared system is required in order to design reliable and quiet transmissions. This study focuses on a system containing a spur gear pair with backlash and periodically time-varying mesh stiffness, and rolling element bearings with clearance type non-linearities. A dynamic finite element model of the linear time-invariant (LTI) system is developed. Effects of several system parameters, such as torsional and transverse flexibilities of the shafts and prime mover/load inertias, on free and force vibration characteristics are investigated. Several reduced order LTI models are developed and validated by comparing their eigen solution with the finite element model results. Several key system parameters such as mean load and damping ratio are identified and their effects on the non-linear frequency response are evaluated quantitatively. Other fundamental issues such as the dynamic coupling between non-linear modes, dynamic interactions between component non-linearities and time-varying mesh stiffness, and the existence of subharmonic and chaotic solutions including routes to chaos have also been examined in depth.

Singh, Rajendra↗
NASA NTRS1984

Effects of cobalt on the hot workability of nickel-base superalloys

The effect of cobalt on the workability of nickel-base superalloys is examined with reference to experimental results for four heats of alloys based on the Nimonic 115 composition with varying amounts of nickel substituted for the nominal 14 percent cobalt. It is shown that Co lowers the gamma-prime solvus, which in turn lowers the Cr23C6 carbide solvus. It is further shown that these solvus temperatures bracket the hot working range for the alloys. However, thermomechanical processing modifications reflecting the effect of Co on the gamma-prime and carbide solvi are shown to restore the workability and the properties of alloys with little or no cobalt.

Jarrett, R. N.↗
NASA NTRS1993

An analytical investigation of transient effects on rewetting of heated thin flat plates

The rewetting of a hot surface is a problem of prime importance in the microgravity application of heat pipe technology, where rewetting controls the time before operations can be re-established following depriming of a heat pipe. Rewetting is also important in the nuclear industry (in predicting behavior during loss-of-coolant accidents), as well as in the chemical and petrochemical industries. Recently Chan and Zhang have presented a closed-form solution for the determination of the rewetting speed of a liquid film flowing over a finite (but long) hot plate subject to uniform heating. Unfortunately, their physically unreasonable initial conditions preclude a meaningful analysis of start-up transient behavior. A new nondimensionalization and closed-form solution for an infinitely-long, uniformly-heated plate is presented. Realistic initial conditions (step change in temperature across the wetting front) and boundary conditions (no spatial temperature gradients infinitely far from the wetting front) are employed. The effects of parametric variation on the resulting simpler closed-form solution are presented and compared with the predictions of a 'quasi-steady' model. The time to reach steady-state rewetting is found to be a strong function of the initial dry-region plate temperature. For heated plates it is found that in most cases the effect of the transient response terms cannot be neglected, even for large times.

Platt, J. A.↗
NASA NTRS1989

PRIME: A bottom-up approach to probabilistic rule development

PRIME is a system to be used by an intelligent machine to allow it to operate in an abstract but uncertain (or stochastic) environment. It maintains a model of the effects of the machine's actions in the form of a rule base, which is induced from experience. This bottom-up approach to rule development allows the model to adapt to changes in the environment. Each rule consists of a condition under which the rule is active, an action, the effect of the action on the environment, and an estimate of the probability of this effect occurring. The effect probabilities are used to model the uncertainty in the environment, permitting multiple possible effects for a single action under a particular set of conditions. The objective of the intelligent machine is to satisfy user-specified goals with maximum probability of success. PRIME fulfills this requirement in two ways: it continuously updates the rule base with the most recent information, to ensure the validity of the model; and it generates plans which have the maximum probability of achieving the goals, based on the probability estimates in the rule base. PRIME is composed of three main processes: exploration, generalization, and planning. In exploration, the machine executes various randomly chosen actions, observes the effects on the environment, and updates the rule base accordingly. This process is used to develop the rule base in simulation, as well as to supplement the current knowledge during normal operation. Generalization is the procedure used to induce general rules from experience, which is encoded in the form of specific rules. These general rules extend the machine's knowledge to situations which have not been encountered yet, thereby increasing the capability of the machine to plan effectively. Planning is the process of constructing an optimal sequence of actions to satisfy a goal, using the rule base to predict the effects of these actions and to determine the probability of success of the plan. The rule representation and many other data structures were specifically chosen to maximize the efficiency of these processes. A simulated environment was designed to test the performance of PRIME. The results of experimentation were largely negative. The main problem was that the domain coverage of the rules was inadequate for the number of rules stored in the rule base, due to redundancies in general rules and numerous rules covering ineffective actions. It was determined that a more efficient generalization, and some form of goal-directed exploration, are necessary in order to solve most of the current deficiencies in PRIME.

Miller, Scott A.↗