Search NASA⌕ Search

SEARCH · Search NASA

Results for “Process variable”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Annealing of (DU-10Mo)-Zr Co-Rolled Foils

Producing uranium-10wt% molybdenum (DU-10Mo) foils to clad with Al first requires initial bonding of the DU-10Mo foil to zirconium (Zr) by hot rolling, followed by cold rolling to final thickness. Rolling often produces wavy (DU-10Mo)-Zr foils that should be flattened before further processing, as any distortions could affect the final alignment and bonding of the Al cladding to the Zr co-rolled surface layer; this bonding is achieved by a hot isostatic pressing (HIP) process. Distortions in the (DU-10Mo)-Zr foil may cause the fuel foil to press against the Al cladding and thus create thinner or thicker areas in the Al cladding layer during the HIP cycle. Post machining is difficult and risky at this stage in the process since there is a chance of hitting the DU-10Mo. Therefore, it is very important to establish a process to flatten and remove any waviness. This study was conducted to determine if a simple annealing treatment could flatten wavy foils. Using the same starting material (i.e. DU-10Mo coupons of the same thickness), five different levels of hot rolling and cold rolling, combined with five different annealing treatments, were performed to determine the effect of these processing variables on flatness, bonding of layers, annealing response, microstructure, and hardness. The same final thickness was reached in all cases. Micrographs, textures, and hardness measurements were obtained for the various processing combinations. Based on these results, it was concluded that annealing at 650°C or higher is an effective treatment to appreciably reduce foil waviness.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Multi-Isotope Process (MIP) Monitor: A Near-Real-Time Monitor For Reprocessing Facilities

INTRODUCTION The threat of protracted diversion of Pu from commercial reprocessing operations is perhaps the greatest concern to national and international agencies tasked with safeguarding these facilities. While it is generally understood that a method for direct monitoring of process on-line and in near-real time (NRT) would be the best defense against protracted diversion scenarios, an effective method with these qualities has yet to be developed. Here, we attempt to bridge this gap by proposing an on-line NRT process monitoring method that should be sensitive to minor alterations in process conditions and compatible with small, easily deployable, detection systems. This Approach is known as the Multi-Isotope Process (MIP) Monitor and involves the determination and recognition of the contaminant pattern within a process stream for a suite of indicator (radioactive) elements present in the spent fuel as a function of process variables. Utilization of a suite of radio-elements, including ones with multiple oxidation states, decreases the likelihood that attempts to divert Pu by altering the ReDox environment within the process would go undetected. In addition, by identifying gamma-emitting indicator isotopes, this Approach might eliminate the need for bulky neutron detection systems, relying instead on small, portable, high-resolution gamma detectors easily deployable throughout the facility.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Friction Hydro-Pillar Processing of a High Carbon Steel: Joint Structure and Properties

A coupled experimental and theoretical study is reported here on friction hydro-pillar processing of AISI 4140 steel, which is a novel solid-state joining technique to repair and fill crack holes in thick-walled components by an external stud. The stud is rotated and forced to fill a crack hole by plastic flow. During the process, frictional heating occurs along the interface of the stud and the wall of crack hole leading to thermal softening of the stud that eases its plastic deformation. The effect of the stud force, its rotational speed and the total processing time on the rate of heat generation and resulting transient temperature field is therefore examined to correlate the processing variables with the joint structure and properties in a systematic and quantitative manner, which is currently scarce in the published literature. The results show that a gentler stud force rate and greater processing time can promote proper filling of the crack hole and facilitate a defect-free joint between the stud and original component.

36 MATERIALS SCIENCE↗

Carbon Nanotube Chopped Fiber for Enhanced Properties in Additive Manufacturing

Nanocomp Technologies, Inc. is working with Oak Ridge National Laboratory to develop carbon nanotube (CNT) composite materials and evaluate their use in additive manufacturing (3D printing). The first phase demonstrated feasibility and improvements for carbon nanotube (CNT)- acrylonitrile butadiene styrene (ABS) composite filaments use in additive manufacturing, with potential future work centering on further improvements. By focusing the initial phase on standard processing methods (developed mainly for the incorporation of carbon fibers in ABS) and characterization techniques, a basis of knowledge for the incorporation of CNTs in ABS was learned. The ability to understand the various processing variables is critical to the successful development of these composites. From the degradation effects on ABS (caused by excessive temperatures), to the length of time the ABS is in the melt state, to the order of addition of constituents, and also to the many possible mixing approaches, a workable flow sequence that addresses each processing step is critical to the final material properties. Although this initial phase could not deal with each of these variables in-depth, a future study is recommended that will build on the lessons learned for this effort.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Perspectives on the relationship between materials chemistry and roll-to-roll electrode manufacturing for high-energy lithium-ion batteries

As lithium-ion battery (LIB) active material and cell manufacturing costs continue to drop with wider adoption of electric vehicles, electrode and cell processing costs remain too high in terms of reaching the ultimate U.S. Department of Energy (DOE) cell cost target of $80/kWh. This paper primarily covers major materials chemistry advancements made over the last 10 years at Oak Ridge National Laboratory (ORNL) in the space of advanced manufacturing science for LIBs with the aim of simultaneously meeting the ultimate cost target, 500 Wh/kg gravimetric energy density, 10-15-min fast charge times, and 1000 deep discharge cycles. Aqeous electrode processing with a variety of active anode and cathode materials is now a standard procedure at the DOE Battery Manufacturing R&D Facility at ORNL (BMF), including the latest processes developed for Ni-rich cathodes. New results on cobalt-free LiNi 0.8 Fe 0.1 Al 0.1 O 2 (NFA 811) are also included and discussed in an electrode processing advantage context. In addition, colloidal processing advancements have been made for Si/C composite anodes for achieving >600 mA h/g capacities. Optimization of electrode coating parameters and drying protocols have been completed, which has elucidated how key processing variables need to be changed when parameters such as slurry solids loading, solvent type, and wet electrode thickness are changed. ORNL has also increased the line speeds at which thick cathodes can be processed using ultra-fast electron beam (EB) curing and substantially decreased formation cycling times to <1 day. Finally, key details of these advancements are discussed in the context of materials chemistry and process-property-performance relationships.

25 ENERGY STORAGE↗

Improving Microstructural Quantification in 3D FIB-SEM Tomography

A detailed understanding of 3D microstructural features is crucial during postprocessing of the acquired data, while determining microstructural properties. Focused ion beam and scanning electron microscopy (fib-sem) is an ideal technique for the acquisition and quantification of 3D microstructures in subsurface features. In this work, we evaluated and implemented approaches to quantify 3D morphological features of plutonium oxalate and oxide particles. Image analysis, as well as statistical analysis were utilized to study the effect of process variables on the pore morphology of plutonium oxalate and oxide particles. The primary results were the creation of morphological maps of particles and identify indicators that correlated parameters allowing for discrimination between direct and reverse strike processes. This enabled us to properly quantify and map particles with their images obtained via sem. For this project, the highest correlation was found to be between Volume and Sphericity (R 2 = 0.7432) for the Revere Strike process, and Volume % and Sphericity (R 2 = 0.7450) for the Direct Strike process.

36 MATERIALS SCIENCE↗

Towards Multilayered Coatings of 304L Stainless Steels Using Friction Surfacing

Abstract The objective of this work is to study friction surfacing process variability when depositing multilayered coatings. This is motivated by the need to maintain deposition quality when depositing multiple friction surfacing layers, whether for repair, remanufacturing, or new part creation using this solid-state metal additive manufacturing process. In this study, 10-mm-diameter 304L stainless steel rods were used to create up to five layers of 40-mm-long coatings on 304L substrates using a constant set of processing parameters. In-process measurement of forces (X, Y, Z), flash temperature, flash geometry, layer temperature, and post-process measurement of layer geometry, microhardness, and microstructure are used to characterize changes in the friction surfacing process as more layers are deposited. It was observed that with increasing layers: layer thickness and deposition efficiency decrease; offsetting of the deposition towards the retreating side, and temperature in the deposited layer increase; and flash temperature does not change. Metallurgical analyses of friction-surfaced cross-sections revealed fine grain refinement and transformation of base austenite to strain-induced martensite. It is concluded that the process parameters need to be adjusted even after the second or third layer is deposited, corrections to the tool path are required after a couple of layers, and the measured process forces, as well as deposited layer temperature, may be useful to monitor and control the process and its instabilities.

Engineering↗

Sampling dynamics for pressurized electrochemical cells

A model describing the gas distribution within a constant pressure electrolysis system and how the distribution impacts electrochemical efficiencies is presented. The primary system of interest is the generation of syngas (CO and H2) associated with the co-electrolysis of H2O and CO2. The model developed for this system takes into account the primary process variables of operation including total system pressure, applied current, the in-flow of reactant gases. From these, and the chemical equilibria within the system, the impact on electrochemically generated gases is presented. Comparing the predicted and measured faradaic efficiency of electrode processes with the expected efficiency from experimental data indicates an offset between the two exists. Methods to minimize and account for the discrepancy are presented with the goal of being able to discern, in a real time manner, degradation of electrode performance. Comparison of the model to experimental data shows a strong correlation between the two with slight variation in experimental data which is attributed to reversible system dynamics such as wetting of the gas diffusion electrode used as the cell cathode.

10 SYNTHETIC FUELS↗

Enhanced Tunability of Gold Nanoparticle Size, Spacing, and Shape for Large-Scale Plasmonic Arrays

Gold nanoparticles are important constituents in plasmonic arrays, lending themselves to electronic, optical, biomedical, sensing, and catalytic applications, among numerous others. Process variables that must be controlled when engineering plasmonic nanoparticle ensembles include nanoparticle size, shape, and spatial distribution on surfaces. The challenge in generating arrays of nanoparticles with control over these three parameters increases dramatically as spatial requirements for uniformity extend to larger processing areas. In this paper, we present a procedure that exploits thermally driven solid-state diffusional dewetting to yield considerable flexibility in generating ensembles of gold nanoparticles. Such submelting dewetting introduces fine control over particle spatial features that are currently difficult to achieve through conventional methods of generating nanoparticle arrays. Because of the simplicity of the process and its area-scalability, solid-state diffusional dewetting is shown here to be a method that could be easily scaled up to apply to large-area plasmonic fabrication processes.

36 MATERIALS SCIENCE↗

Extraction of Xenon using Enriching Reflux Pressure Swing Adsorption

Measuring radioactive xenon isotopes in the atmosphere is an important technique used for monitoring within the Comprehensive Nuclear-Test-Ban Treaty (CTBT). Several process steps are needed to capture and prepare a xenon sample suitable for transfer to a nuclear detector. These processes include air drying, xenon collection, concentration and purification. The ideal xenon sampling system would be small, have low power consumption, not use consumables (such as helium gas or liquid nitrogen) and be fully automated, robust and dependable. Due to the low concentration of xenon in the air, the most energy intensive part of the gas processing is the first stage collection and concentration. Pacific Northwest National Laboratory has developed a batch mode enriching-reflux pressure-swing-adsorption (ER-PSA) process that shows promise as a xenon collection and concentration technique. The development of this process was guided by finite element models of the process chemistry. The modeling showed minimizing the xenon dispersion in the adsorption columns is critical to achieving a good separation. Prior to hardware construction, models were used to determine appropriate trap dimensions, adsorbent particle size and optimum process variables such as cycle steps, step times, and flow rates. A bench top ER-PSA unit was constructed and testing under various operating conditions has begun. The results obtained in these initial parametric experiments have provided insight into the physics of the process and have refined the mathematical models. The combination of modeling and experiment provides a better understanding of process physics than either experiment or models alone. The bench top system has demonstrated room temperature collection of xenon with a xenon enrichment of 1000 (starting from air) with a modest pressure ratio of 7-10 resulting in an energy efficient separation technique. The technique does not use exotic adsorbents, cryogenic temperatures or high pressure compressors, enabling a small, low power and robust system. This ER-PSA process is an enabling technology for small energy efficient xenon collectors, desirable qualities for next generation international xenon systems.

Williams, Richard M.↗

Assessment of firing conditions in old fired-clay bricks: The contribution of X-ray powder diffraction with the Rietveld method and small angle neutron scattering

Full characterization of fired-clay bricks is crucial for the improvement of process variables in manufacturing and, in case of old bricks, for restoration/replacement purposes. To this aim, five bricks produced in a plant in Czech Republic in the past have been investigated with a combination of analytical techniques in order to derive information on the firing process. An additional old brick from another brickyard was also used to study the influence of different raw materials on sample microstructure. The potential of X-ray diffraction with the Rietveld method and small angle neutron scattering technique has been exploited to describe the phase transformations taking place during firing and characterize the brick microstructure. Unit-cell parameter of spinel and amount of hematite are proposed as indicators of the maximum firing temperature, although for the latter, limited to bricks produced from the same raw material. The fractal quality of the surface area of pores obtained from small angle neutron scattering is also suggested as a method to distinguish between bricks produced from different raw clays. - Highlights: • Rietveld method helps in describing microstructure and physical properties of bricks. • XRPD derived cell parameter of spinel is proposed as an indicator of firing temperature. • SANS effectively describes brick micro and nanostructure, including closed porosity. • Fractal quality of pore surface is proposed as ‘fingerprint’ of brick manufacturing.

36 MATERIALS SCIENCE↗

FEM Analysis of Defects and Microstructure Evolution during Hot Working of Specialty Alloys

The main goals of process simulation in manufacturing are to reduce manufacturing/part development time and cost as well as increasing quality and productivity. In this study, porosity evolution is modeled by introducing a porosity evolution parameter, which is function of strain rate and stress triaxiality factor. Applicability is shown by simulating the first two stages of an ingot conversion process; variables are die geometry and bite size. Moreover, application is extended to hot shape rolling, where the geometry of the oval passes is the variable. Validation is carried out through evaluation of samples from final products. Also, surface defects in hot shape rolling are tracked by studying the instability during the rolling of the material. Plastic work approach was used to judge the occurrence of instability during the process. The effect of number of passes and roll gap was examined to predict the occurrence of surface cracking. On the other hand, unrecrystallized grains and coarse grain problem are other significant problems in the metalworking industry. A recrystallization model is implemented in a finite element framework, to study the effect of forging parameters on the microstructure evolution during ingot conversion process of a superalloy.

36 MATERIALS SCIENCE↗

Optimization of direct conversion of wet algae to biodiesel under supercritical methanol conditions

This study demonstrated a one-step process for direct liquefaction and conversion of wet algal biomass containing about 90% of water to biodiesel under supercritical methanol conditions. This one-step process enables simultaneous extraction and transesterification of wet algal biomass. The process conditions are milder than those required for pyrolysis and prevent the formation of by-products. In the proposed process, fatty acid methyl esters (FAMEs) can be produced from polar phospholipids, free fatty acids, and triglycerides. A response surface methodology (RSM) was used to analyze the influence of the three process variables, namely, the wet algae to methanol (wt./vol.) ratio, the reaction temperature, and the reaction time, on the FAMEs conversion. Algal biodiesel samples were analyzed by ATR-FTIR and GC-MS. Based on the experimental analysis and RSM study, optimal conditions for this process are reported as: wet algae to methanol (wt./vol.) ratio of around 1:9, reaction temperature and time of about 255 °C, and 25 min respectively. This single-step process can potentially be an energy efficient and economical route for algal biodiesel production.

09 BIOMASS FUELS↗

SU-E-T-760: Tolerance Design for Site-Specific Range in Proton Patient QA Process Using the Six Sigma Model

Purpose: To show how tolerance design and tolerancing approaches can be used to predict and improve the site-specific range in patient QA process in implementing the Six Sigma. Methods: In this study, patient QA plans were selected according to 6 site-treatment groups: head &neck (94 cases), spine (76 cases), lung (89 cases), liver (53 cases), pancreas (55 cases), and prostate (121 cases), treated between 2007 and 2013. We evaluated a model of the Six Sigma that determines allowable deviations in design parameters and process variables in patient-specific QA, where possible, tolerance may be loosened, then customized if it necessary to meet the functional requirements. A Six Sigma problem-solving methodology is known as DMAIC phases, which are used stand for: Define a problem or improvement opportunity, Measure process performance, Analyze the process to determine the root causes of poor performance, Improve the process by fixing root causes, Control the improved process to hold the gains. Results: The process capability for patient-specific range QA is 0.65 with only ±1 mm of tolerance criteria. Our results suggested the tolerance level of ±2–3 mm for prostate and liver cases and ±5 mm for lung cases. We found that customized tolerance between calculated and measured range reduce that patient QA plan failure and almost all sites had failure rates less than 1%. The average QA time also improved from 2 hr to less than 1 hr for all including planning and converting process, depth-dose measurement and evaluation. Conclusion: The objective of tolerance design is to achieve optimization beyond that obtained through QA process improvement and statistical analysis function detailing to implement a Six Sigma capable design.

60 APPLIED LIFE SCIENCES↗

Chapter 4: "Waste"-to-Energy for Decarbonization - Transforming Nut Shells Into Carbon-Negative Electricity

This chapter presents a study demonstrating waste pistachio nut shells as a renewable feedstock for climate-friendly electricity generation via industrial gasification technology. The study includes biomass feedstock characterization (i.e., pistachio waste critical material attributes), process variability (i.e., bulk material handling), and overall operational reliability and conversion performance through extended testing. Additionally, techno-economic analysis (TEA) and life cycle assessment (LCA) were performed to assess the economic feasibility and environmental impact of the technology to transform agricultural waste to biopower. For processing pistachio waste material, among critical material attributes, fines content in the biomass (<1/4") had the largest potential to reduce the operating time of the gasifiers due to plugging. Pelletizing fines and co-feeding them with the mixed pistachio waste increased the average feed density, feed rate, and biochar production. Compared to pine wood chips, mixed pistachio waste yielded higher biochar quantity but slightly reduced quality. In general, a systematic Quality by Design methodology is the preferred approach for designing preprocessing and material conveyance systems, where a downstream technology (end user) for the produced intermediate is specified at the outset. TEA results show that the biochar production rate and selling price had an overwhelming impact on the modeled Minimum Electricity Selling Price (MESP), which ranged from 35.5 to 39.9 cents/kWh for the cases studied (16 h/day operational basis). Moreover, LCA results show that the valorization of pistachio shells for biopower generation is a "carbon negative" process that can help decarbonize the U.S. electricity grid. The specific carbon intensity was -0.29 to -0.71 kg CO2e/kWh, compared to 0.45 kg CO2e/kWh for the average U.S. electricity mix. Biochar production from pistachio waste as a potential means for carbon sequestration was a significant driver for the LCA. The highly stable biochar permanently sequesters a considerable fraction of biochar carbon in the ground, more than enough to offset the life cycle emissions, and can be a complementary climate change mitigation strategy.

bio-char↗

Mechanical Performance of Additively Manufactured ODS 316L and 316H Stainless Steels

This work package within the Advanced Materials and Manufacturing Technologies (AMMT) program focused on the mechanical and microstructural characterization of oxide dispersion strengthened (ODS) stainless steels produced using advanced manufacturing techniques. The research aimed to identify an accelerated development path for ODS alloys by integrating additive manufacturing (AM) technologies with recent advancements in ODS materials and traditional manufacturing methods. For FY 24, the research specifically targeted exploring an accelerated development path for ODS alloys by combining AM technologies with these advancements. Novel AM and post-build processing routes were developed for ODS austenitic alloys, including Fe-Cr-Ni alloys such as 316L and 316H. Electron microscopy and mechanical characterizations were conducted to evaluate the impact of process variables on microstructure and properties, with the goal of optimizing these properties economically. Traditionally, producing ODS alloys involves multi-day, high-energy mechanical milling of alloy powder with yttria powder, followed by milled-powder consolidation through extrusion or other methods, and additional thermomechanical processing (TMP) for property control. To overcome the challenges associated with this complex and costly approach, we propose exploring alternative, cost-effective processing routes that emphasize AM and traditional TMP methods. The new processing routes for ODS alloys have achieved significantly higher strengths—several times greater than those of wrought stainless steels—while maintaining substantial ductility and fracture toughness. This report outlines the novel and economical AM-based processing routes for ODS austenitic alloys, combined with post-build TMPs, and discusses the mechanical and microstructural characteristics of the developed materials.

36 MATERIALS SCIENCE↗

Mechanical Characteristics of Additively Manufactured ODS 316L and 316H Alloys with and Without Post-build Processing

This research aims to explore an accelerated development path for oxide dispersion-strengthened (ODS) alloys by integrating additive manufacturing (AM) technologies with recent advances in ODS materials and traditional manufacturing methods. Novel AM and post-build processing routes have been developed for ODS austenitic alloys, specifically Fe-Cr-Ni alloys like 316L and 316H. Electron microscopy and mechanical characterizations were conducted to evaluate the effects of process variables on microstructure and properties, aiming for an economically feasible route property optimization. Traditionally, ODS alloy production involves multi-day high-energy mechanical milling of alloy powder with yttria (Y 2 O 3 ) followed by powder consolidation via extrusion or other methods and additional thermomechanical processing (TMP) for property control. Here, to address these challenges associated with this complex and costly approach, we propose exploring alternative, cost-effective processing routes focusing on AM and traditional TMP methods. The new ODS alloy processing routes have achieved up to a 400% increase in yield strength and a 60% increase in ultimate tensile strength compared to wrought stainless steels while still maintaining significant ductility and fracture toughness. This paper details the novel and economical AM-based processing routes for ODS austenitic alloys, combined with post-build TMPs, and discusses the mechanical and microstructural characteristics of the developed materials.

Byun, Thak Sang [Oak Ridge National Laboratory (OR↗

Optimizing high energy density sulfur cathodes: A multivariate approach to electrode formulation and processing

Lithium-sulfur (Li-S) batteries involve complex solid-liquid-solid phase transformations during both discharging and charging processes, where cathode materials, formulation, and structure play a crucial role. Here, a design of experiments (DoE) methodology and an empirical model are developed to systematically explore the interactions and trade-offs among cathode factors and process variables, and to obtain generalizable effects estimates for the multivariate system. Compared to the conventional one-factor-at-a-time (OFAT) approach, this work demonstrates advantages in both efficiency and accuracy by allowing the data to guide future research and decisions. Further, an optimized cathode formulation and processing parameters are predicted and validated experimentally, achieving over 1000 mAh g -1 in discharge capacity and improved cycling under practical lean electrolyte (4 µL mg -1 S) and high S-loading cathodes (>4 mg cm -2 ) conditions. The optimized cathode was scaled up and assembled into Li-S pouch cells, achieving 316 Wh kg -1 in cell-level energy, proving that the comprehensive and rigorous framework for optimizing complex systems with DoE leads to improved performance in a practical pouch cell system.

25 ENERGY STORAGE↗