A study of the required critical aspect ratio of fibers in composites intended for stress- rupture applications
Critical aspect ratio of W fibers in metal matrix composites for stress rupture applications
Jech, R. W.↗
SEARCH · Search NASA
Results for “RUPTURES”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Creep-rupture tests of internally pressurized Rene 41 tubes
Weld-drawn tubes of Rene 41 with 0.935 centimeter outside diameter and 0.064 centimeter wall thickness were tested to failure at temperatures from 1117 to 1233 K and internal helium pressures from 5.5 to 12.4 meganewtons per square meter. Lifetimes ranged from 5 to 2065 hours. The creep-rupture strength of the tubes was 50 percent lower than that of unwelded, thick sheet specimens, and 20 percent lower than that of unwelded, thin sheet specimens. Larson-Miller correlations and photomicrographs of some specimens are presented.
Gumto, K. H.↗
Sensitivity of the creep-rupture properties of Waspaloy sheet to sharp-edged notches in the temperature range 1000-1400 deg F.
Time-dependent notch sensitivity of Waspaloy was observed at test temperatures from 1000 to 1300 deg F. Its occurrence in this range was dependent on the heat treatment. ?Overaging' eliminated the notch sensitivity. Optimum combination of smooth and notched specimen strengths for material solution treated at 1975 deg F were obtained by aging 24 hr at 1550 deg F. Necessary conditions for time-dependent notch sensitivity were (1) the notch specimen loads had to be below the approximate 0.2 percent offset yield strength; and (2 ) test data from smooth specimens had to indicate that small amounts of creep used up large fractions of creep-rupture life. No reasons were evident why these criteria will not prove applicable to other alloys.
Wilson, D. J.↗
Abrasion and catastrophic rupture of lunar rocks - Some implications to the micrometeoroid flux at 1 AU.
Results from laboratory studies of hypervelocity impact against crystalline rocks, combined with estimates of the micrometeoroid flux at the lunar surface, provide a basis for calculating abrasion rates and survival times before catastrophic rupture of rocks on the lunar surface. The surface residence times observed for lunar rocks of the order of 10 m.y. (derived from the track densities of iron group nuclei) restrict the mass range of impacting particles of interest to masses less than about 1.01 gram. Extrapolation downward to smaller masses following flux distributions suggested by early satellite data and photographic meteor observations leads to absurd rates of abrasion. Consistent with the observed crater populations on the lunar rocks and with the Pegasus, Explorer, and Pioneer satellite data, the slope of the mass-flux distribution must decrease markedly for masses below 1 to .1 microgram.
Gault, D. E.↗
Creep-rupture tests of internally pressurized Inconel 702 tubes
Seamless Inconel 702 tubes with 0.375-in. outside diameter and 0.025-in. wall thickness were tested to failure at temperatures from 1390 to 1575 F and internal helium pressures from 700 to 1800 psi. Lifetimes ranged from 29 to 1561 hr. The creep-rupture strength of the tubes was about 70 percent lower than that of sheet specimens. Larson-Miller correlations and photomicrographs of some specimens are presented.
Gumto, K. H.↗
Creep-rupture tests of internally pressurized Hastelloy-X tubes
Seamless Hastelloy-X tubes with 0.375-in. outside diameter and 0.025-in. wall thickness were tested to failure at temperatures from 1400 to 1650 F and internal helium pressures from 800 to 1800 psi. Lifetimes ranged from 58 to 3600 hr. The creep-rupture strength of the tubes was from 20 to 40 percent lower than that of sheet specimens. Larson-Miller correlations and photomicrographs of some specimens are presented.
Gumto, K. H.↗
A molecular theory of elastomer deformation and rupture.
The mechanical properties of elastomers, including rupture and its time dependence, can be semiquantitatively predicted from nine molecular parameters which are characteristic for a given species, from the initial molecular weight of a sample before cross-linking and from the effective chain concentration (which must still be determined for each vulcanizate). Only two empirical quantities are involved - the Plazek retardation function for entanglement slippage and a related constant which serves to locate this function on the time scale. The theory leads to a new method of estimating fatigue lifetimes from short-time data.
Landel, R. F.↗
A film-rupture model of hydrogen-induced, slow crack growth in alpha-beta titanium
The appearance of the terrace like fracture morphology of gaseous hydrogen induced crack growth in acicular alpha-beta titanium alloys is discussed as a function of specimen configuration, magnitude of applied stress intensity, test temperature, and hydrogen pressure. Although the overall appearance of the terrace structure remained essentially unchanged, a distinguishable variation is found in the size of the individual terrace steps, and step size is found to be inversely dependent upon the rate of hydrogen induced slow crack growth. Additionally, this inverse relationship is independent of all the variables investigated. These observations are quantitatively discussed in terms of the formation and growth of a thin hydride film along the alpha-beta boundaries and a qualitative model for hydrogen induced slow crack growth is presented, based on the film-rupture model of stress corrosion cracking.
Nelson, H. G.↗
A film-rupture model of hydrogen-induced, slow crack growth in acicular alpha-beta titanium
A study has been conducted of the terrace-like fracture morphology of gaseous hydrogen-induced crack growth in acicular alpha-beta titanium alloys in terms of specimen configuration, magnitude of applied stress intensity, test temperature, and hydrogen pressure. Although the overall appearance of the terrace structure remained essentially unchanged, a distinguishable variation is found in the size of the individual terrace steps, and step size is found to be inversely dependent upon the rate of hydrogen-induced slow crack growth. This inverse relationship is independent of all the variables investigated. These observations are quantitatively discussed in terms of the formation and growth of a thin hydride film along the alpha-beta boundaries and a qualitative model for hydrogen-induced slow crack growth is presented, based on the film-rupture model of stress corrosion cracking.
Nelson, H. G.↗
Tensile and creep rupture properties of (16) uncoated and (2) coated engineering alloys at elevated temperatures
Sixteen test materials were supplied by NASA-Lewis Research Center as wrought bar or cast remelt stock. The cast remelt stock was cast into test blanks with two such materials being also evaluated after Jocoat coating was applied. Mechanical properties evaluated included tensile, modulus of elasticity, Poisson's Ratio, creep properties and creep rupture strength. Tests were conducted at temperatures applicable to the service temperature of the various alloys. This range extended from room temperature to 1000 C.
Fritz, L. J.↗
Interpolation and Extrapolation of Creep Rupture Data by the Minimum Commitment Method. Part 3: Analysis of Multiheats
The Minimum Commitment Method was applied to two sets of data for which multiple heat information was available. For one alloy, a 304 stainless steel studied in Japan, data on nine well characterized heats were used, while for a proprietary low alloy carbon steel studied in the United Kingdom data were available on seven heats - in many cases to very long rupture times. For this preliminary study no instability factors were used. It was discovered that heat-to-heat variations would be accounted for by introducing heat identifiers in the form A + B log sigma where sigma is the stress and the constants A and B depend only on the heat. With these identifiers all the data could be collapsed onto a single master curve, even though there was considerable scatter among heats. Using these identifiers together with the average behavior of all heats made possible the determination of an accurate constitutive equation for each individual heat. Two basic approaches are discussed for applying the results of the analysis.
Manson, S. S.↗
Interpolation and extrapolation of creep rupture data by the minimum commitment method. II - Oblique translation
An outline is presented of a new procedure, termed the oblique translation method, which emerged in the development of the focal point convergence method. Approaches for implementing the oblique translation method are discussed. It is shown that the new method is essentially a minimum commitment method when manually-graphically implemented, in the sense that the form of the functions involved are not forced into particular analytical forms. The individual constants and functions are independently determined. The minimum commitment concept is extended to the analysis of creep rupture data wherein each isothermal is to be generated by an oblique translation of the 'master curve' when plotted. Attention is given to a manual-graphical analysis, the preassessment of data, and an analysis by computer code.
Manson, S. S.↗
Interpolation and extrapolation of creep rupture data by the minimum commitment method. I - Focal-point convergence
The minimum commitment method has been applied to the analysis of creep-rupture data. The method is based on a parameter representing the focal point of convergence of all isothermals when extended to the long or short times necessary for such convergence to occur. The technique may be applied by manual-graphic analysis on computer code. It is illustrated for the nickel-base alloy Astroloy.
Manson, S. S.↗
Modules of rupture and oxidation resistance of S12.55Al0.6O0.72N3.52 sialon
A Sialon of formula Si2.55Al0.6O0.72N3.52 was made from ball-milled alpha-Si3N4, AIN, and SiO2 by sintering the powder compacts at 1760 C for 4 hours in stagnant nitrogen. This Sialon had an average modulus of rupture ranging from 404 megapascals (58.6 ksi) at room temperature to 254 megapascals (36.8 ksi) at 1400 C. Oxidation tests at 1400 C in air showed it to have a parabolic oxidation rate constant less than or equal to 2.8x10 to the -10th power sq g/cm4 hr, which is smaller than that of any other Si3N4-base ceramic reported in the literature.
Arias, A.↗
Theory of time-dependent rupture in the Earth
Fracture mechanics is used to develop a theory of earthquake mechanism which includes the phenomenon of subcritical crack growth. The following phenomena are predicted: slow earthquakes, multiple events, delayed multiple events (doublets), postseismic rupture growth and afterslip, foreshocks, and aftershocks. The theory predicts a nucleation stage prior to an earthquake, and suggests a physical mechanism by which one earthquake may 'trigger' another.
Das, S.↗
Some observations regarding the statistical determination of stress rupture regression lines
Observations concerning the statistical evaluation of creep data are presented. Methods currently employed in the determination of stress rupture regression lines can result in conflicting and necessarily invalid results. Anomalous behavior is principally associated with the selection of the dependent variable. However, it is the least squares method of curve fitting which introduces regression bias. Methods to improve the validity of least squares regressions are suggested.
Pizzo, P. P.↗
MEGA16 - Computer program for analysis and extrapolation of stress-rupture data
The computerized form of the minimum commitment method of interpolating and extrapolating stress versus time to failure data, MEGA16, is described. Examples are given of its many plots and tabular outputs for a typical set of data. The program assumes a specific model equation and then provides a family of predicted isothermals for any set of data with at least 12 stress-rupture results from three different temperatures spread over reasonable stress and time ranges. It is written in FORTRAN 4 using IBM plotting subroutines and its runs on an IBM 370 time sharing system.
Ensign, C. R.↗
The rupture process and asperity distribution of three great earthquakes from long-period diffracted P-waves
The variation of maximum earthquake size along the subduction zones has been interpreted as a variation in the seismic coupling ostensibly related to the mechanical conditions of the fault zone. Great differences are noted between the seismographs of the three great earthquakes whose rupture processes are presently considered: in the Kurile Islands (1963), The Rat Islands (1965) and Alaska (1964). On-scale long period P waves were recorded in all cases. Source time functions are deconvolved from the observed periods. It is concluded that maximum earthquake size is related to the asperity distribution on the fault. The subduction zones with the largest earthquakes have very large asperities, as in the Alaskan case, while the zones with the smaller great earthquakes, such as the Kurile Islands, have smaller scattered asperities.
Ruff, L.↗