SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Data-compression processing systems based on an analog-to-digital converter /ADC/, includes a qualitative comparator for comparison of the ADC output with a ramp generator, which is connected as a bidirectional binary counter with selective inputs. A bidirectional ramp counter selects the proper ramp through a ramp generator selection network.
The procedures and unique hardware used to conduct an experimental investigation into the response of a small-turboshaft-engine compression system to various hot gas ingestion patterns are presented. The temperature distortion generator described herein uses gaseous hydrogen to create both steady-state and time-variant, or transient, temperature distortion at the engine inlet. The range of transient temperature ramps produced by the distortion generator during the engine tests was from less than 111 deg K/sec (200 deg R/sec) to above 611 deg K/sec (1100 deg R/sec); instantaneous temperatures to 422 deg K (760 deg R) above ambient were generated. The distortion generator was used to document the maximum inlet temperatures and temperature rise rates that the compression system could tolerate before the onset of stall for various circumferential distortions as well as the compressor system response during stall.
The procedures and unique hardware used to conduct an experimental investigation into the response of a small-turboshaft-engine compression system to various hot gas ingestion patterns are presented. The temperature distortion generator described herein uses gaseous hydrogen to create both steady-state and time-variant, or transient, temperature distortion at the engine inlet. The range of transient temperature ramps produced by the distortion generator during the engine tests was from less than 111 deg K/sec (200 deg R/sec) to above 611 deg K/sec (1100 deg R/sec); instantaneous temperatures to 422 deg K (760 deg R) above ambient were generated. The distortion generator was used to document the maximum inlet temperatures and temperature rise rates that the compression system could tolerate before the onset of stall for various circumferential distortions as well as the compressor system response during stall.
An experimental study was conducted to determine the performance of a two-dimensional, mixed-compression bifurcated duct inlet system designed for a free-stream Mach number of 2.7. Thirty percent of the supersonic area contraction occurred internally. A movable ramp was used to vary the contraction ratio for off-design operation. Boundary layer bleed regions were located on the cowl, centerbody, and sidewall surfaces. There were also provisions for vortex generators on the cowl and centerbody of the subsonic diffuser. Data were obtained over the Mach number range of 2.0 to 2.8 and at angles of yaw from 0 deg. to the maximum value prior to inlet un-start. The test at Mach 2.8 was to obtain data for an over- speed condition. The Reynolds number varied from 2.5 to 2.3 million/ft for Mach numbers above 2.5. At Mach numbers of 2.5 and lower, the Reynolds number was set at 2.5 million/ft. Bleed patterns, vortex generator patterns, and ramp position were varied, and three inlet configurations were selected for more extensive study. Two of these configurations had self-starting capability. The self-starting configuration that was developed produced 89 percent total pressure recovery at the compressor face station with 6.8 percent total bleed. The compressor face distortion was about 16 percent. Vortex generators were extremely effective in re-distributing flow but were not as effective in reducing distortion. Excellent flow symmetry was achieved between the separated halves of the inlet, and twin-duct instability was not observed. The ramp tip shock was steeper than expected. This caused the cowl lip shock to be reflected from the ramp instead of being cancelled at the shoulder. However, peak recovery at the throat was still obtained with the ramp near the design position.
Experiments were conducted in a two-stream planar mixing layer facility at convective Mach numbers of 0.28 and 0.62. Mie scattering from condensed alcohol droplets and planar laser-induced fluorescence (PLIF) of nitric oxide were used for flow visualization in both the side and plan views. The PLIF signals were approximately proportional to mixture fraction and were used to generate statistical quantities. Visualizations using both the Mie scattering and PLIF indicate the structure is essentially two-dimensional at Mc = 0.28 and three-dimensional at Mc = 0.62. Perspective renderings of side view images show the structures are streamwise ramped at Mc = 0.28 and cross-stream ramped at Mc = 0.62. This difference appears to be associated with decreasing streamwise structure spacings at the higher Mc condition. The statistical analysis suggests that with increasing compressibility, the scalar fluctuations are smaller, and the fraction of mixed fluid is higher.
Future space missions are going to require large focal planes with many sensing arrays and hundreds of millions of pixels all read out at high data rates'' . This will place unique demands on the electrical and electronics (EE) subsystem design and it will be critically important to have high technology readiness level (TRL) EE concepts ready to support such missions. One such omission is the Joint Dark Energy Mission (JDEM) charged with making precise measurements of the expansion rate of the universe to reveal vital clues about the nature of dark energy - a hypothetical form of energy that permeates all of space and tends to increase the rate of the expansion. One of three JDEM concept studies - the Dark Energy Space Telescope (DESTINY) was conducted in 2008 at the NASA's Goddard Space Flight Center (GSFC) in Greenbelt, Maryland. This paper presents the EE subsystem framework, which evolved from the DESTINY science instrument study. It describes the main challenges and implementation concepts related to the design of an EE subsystem featuring multiple focal planes populated with dozens of large arrays and millions of pixels. The focal planes are passively cooled to cryogenic temperatures (below 140 K). The sensor mosaic is controlled by a large number of Readout Integrated Circuits and Application Specific Integrated Circuits - the ROICs/ASICs in near proximity to their sensor focal planes. The ASICs, in turn, are serviced by a set of "warm" EE subsystem boxes performing Field Programmable Gate Array (FPGA) based digital signal processing (DSP) computations of complex algorithms, such as sampling-up-the-ramp algorithm (SUTR), over large volumes of fast data streams. The SUTR boxes are supported by the Instrument Control/Command and Data Handling box (ICDH Primary and Backup boxes) for lossless data compression, command and low volume telemetry handling, power conversion and for communications with the spacecraft. The paper outlines how the JDEM DESTINY concept instrument EE subsystem can be built now, a design; which is generally U.S. Government work not protected by U.S. copyright IEEEAC paper # 1429. Version 4. Updated October 19, 2009 applicable to a wide variety of missions using large focal planes with lar ge mosaics of sensors.
Double shell targets are a promising potential avenue to obtain robust neutron yield at current laser facilities. Similar to single shell designs, double shells require the symmetric implosion of an ablator in order to uniformly compress and heat a fuel volume, with the goal of achieving thermonuclear burn. Significant differences between double and single shells include the usage of an aluminum ablator as well as a reverse ramp laser pulse. In addition, double shells require a different convergence than single shells for fuel ignition. Numerical implosion studies at various energies with comparisons to experimental outcomes are required to gain confidence that simulations can capture the ablator shape from subscale to full scale. The current work builds on previous implosion experiments conducted at 1-MJ laser energy to confirm achieved ablator symmetry at 1.25 and 1.5 MJ. Average ablator P2 and P4 shapes measured in these experiments are within 5% of the simulated shape, which merits the platforms for further experimental studies.
Double shell targets are a promising potential avenue to obtain robust neutron yield at current laser facilities. Similar to single shell designs, double shells require the symmetric implosion of an ablator in order to uniformly compress and heat a fuel volume, with the goal of achieving thermonuclear burn. Significant differences between double and single shells include the usage of an aluminum ablator as well as a reverse ramp laser pulse. In addition, double shells require a different convergence than single shells for fuel ignition. Numerical implosion studies at various energies with comparisons to experimental outcomes are required to gain confidence that simulations can capture the ablator shape from subscale to full scale. The current work builds on previous implosion experiments conducted at 1-MJ laser energy to con firm achieved ablator symmetry at 1.25 and 1.5 MJ. Average ablator P2 and P4 shapes measured in these experiments are within 5% of the simulated shape, which merits the platforms for further experimental studies.
The structure of the separated flow region over a 20 degree compression corner at a free-stream Mach number of 2.84 is investigated computationally using a Reynolds averaged Navier Stokes (R.A.N.S.) solver and kappa-epsilon model. At this Mach number and ramp angle, a steady-state recirculation region of order delta(sub o) is observed, with onset of a 'plateau' in the wall pressure distribution near the corner. At lower ramp angles, separation is negligible, while at an angle of 24 degrees, separation regions of length 2 delta(sub o) are expected. Of interest here is the response of the mathematical model to inclusion of the pressure dilatation term for turbulent kinetic energy. Compared with the experimental data of Smits and Muck (1987), steady-state computations show improvement when the pressure dilatation term is included. Unsteady computations, using both unforced and then forced inlet conditions, did not predict the oscillatory motion of the separation bubble as observed in laboratory experiments. An analysis of the separation bubble oscillation and the turbulent boundary layer (T.B.L.) frequencies for this flow suggests that the bubble oscillations are of nearly the same order as the turbulent frequencies, and therefore difficult for the model to separate and resolve.
Vortex generators within a two-dimensional, external-compression supersonic inlet for Mach 1.6 were investigated to determine their ability to increase total pressure recovery, reduce total pressure distortion, and improve the boundary layer. The vortex generators studied included vanes and ramps. The geometric factors of the vortex generators studied included height, length, spacing, and positions upstream and downstream of the inlet terminal shock. The flow through the inlet was simulated through the computational solution of the steady-state Reynolds-averaged Navier-Stokes equations on multi-block, structured grids. The vortex generators were simulated by either gridding the geometry of the vortex generators or modeling the vortices generated by the vortex generators. The inlet performance was characterized by the inlet total pressure recovery, total pressure distortion, and incompressible shape factor of the boundary-layer at the engine face. The results suggested that downstream vanes reduced the distortion and improved the boundary layer. The height of the vortex generators had the greatest effect of the geometric factors.
A thermodynamic study has been conducted that investigated the effects of the boost-phase environment on densified propellant thermal conditions for expendable launch vehicles. Two thermodynamic models were developed and utilized to bound the expected thermodynamic conditions inside the cryogenic liquid hydrogen and oxygen propellant tanks of an Atlas IIAS/Centaur launch vehicle during the initial phases of flight. The ideal isentropic compression model was developed to predict minimum pressurant gas requirements. The thermal equilibrium model was developed to predict the maximum pressurant gas requirements. The models were modified to simulate the required flight tank pressure profiles through ramp pressurization, liquid expulsion, and tank venting. The transient parameters investigated were: liquid temperature, liquid level, and pressurant gas consumption. Several mission scenarios were analyzed using the thermodynamic models, and the results indicate that flying an Atlas IIAS launch vehicle with densified propellants is feasible and beneficial but may require some minor changes to the vehicle.
Computational fluid dynamics simulations are performed as part of a process to design a vortex generator array for a two-dimensional inlet for Mach 1.6. The objective is to improve total pressure recovery a on at the engine face of the inlet. Both vane-type and ramp-type vortex generators are examined.
Voyager 1 has been moving through the very local interstellar medium (VLISM) from the time that it crossed the heliopause on 2012/DOY 238 to 2020/DOY 292. Three notable objects in the magnetic field of the VLISM have been observed: two shocks and one pressure front. This paper reports the observation of a fourth object observed near 2020/DOY 147. There were no upstream electron plasma oscillations of the type often observed ahead of shocks, abrupt increases in energetic particles, or fluctuations in the 48 s increments of the magnetic field associated with this feature, suggesting that it was probably not a shock. This feature was associated with a relatively large increase in the magnetic field strength(B2/B1=1.35)and in the electron density determined by the Plasma Wave Science experiment (N2/N1=1.36) using a new method described in this paper. This feature appears to be a pressure front associated with a compressive wave in the VLISM. The two shocks and the two pressure fronts were associated with the four largest maxima observed in B (t) between 2012/DOY 238 and 2020/DOY 292. Each feature was associated with a jump–ramp structure. The jump–ramp structures were separated by long relatively undisturbed quiet intervals.
A large scale, variable-geometry inlet system with a design Mach number of 3.0 was tested at Mach numbers from 0.6 to 1.28. Variable features for off-design operation are an adjustable-height ramp system and a translating cowl. Experimental results are presented for transonic ramp and cowl positions showing the effect of throat boundary layer bleed and vortex generators on engine-face performance. Detailed pressure and force-balance data are used to evaluate transonic drag characteristics.
A gammaT scheme may be required for the PIP-II era performance or ACE-MIRT era performance of the Booster. PIP-II era operations of the Fermilab proton complex will require the Fermilab Booster to increase beam intensity from 4.5e12 to 6.5e12 protons, while also increasing its ramp from 15 Hz to 20 Hz. These changes pose particular challenges for transition-crossing in the Booster, where longitudinal beam quality must be controlled in order to facilitate slip-stacking in the Recycler Ring later in the Main Injector cycle. Two novel gammaT jump schemes are proposed, termed “double gammaT jump” and “partial gammaT jump”, which optimize the magnitude of the gammaT jump within optics and power supply constraints.
The two-dimensional time-dependent Euler equations which govern the flow field resulting from the interaction of a planar shock with a compression corner are solved for initial conditions which result in single Mach reflection of the incident planar shock. The Euler equations are first transformed to include the self-similarity of the flow field. A second transformation is employed to normalize the distances between the ramp and the reflected shock and between the wall and the Mach stem. The resulting equations in strong conservation-law form are solved using a second-order discontinuity-fitting finite-difference approach. The results are compared with experimental interferograms and existing first-order shock-capturing numerical solutions.
The external combustion of hydrogen to reduce transonic drag was investigated. A control volume analysis is developed and indicates that the specific impulse performance of external burning is competitive with other forms of airbreathing propulsion and depends on the fuel-air ratio, freestream Mach number, and the severity of the base drag. A method is presented for sizing fuel injectors for a desired fuel-air ratio in the unconfined stream. A two-dimensional Euler analysis is also presented which indicates that the total axial force generated by external burning depends on the total amount of energy input and is independent of the transverse and streamwise distribution of heat addition. Good agreement between the Euler and control volume analysis is demonstrated. Features of the inviscid external burning flowfield are discussed. Most notably, a strong compression forms at the sonic line within the burning stream which may induce separation of the plume and prevent realization of the full performance potential. An experimental program was conducted in a Mach 1.26 free-jet to demonstrate drag reduction on a simple expansion ramp geometry, and verify hydrogen-air stability limits at external burning conditions. Stable combustion appears feasible to Mach number of between 1.4 and 2 depending on the vehicle flight trajectory. Drag reduction is demonstrated on the expansion ramp at Mach 1.26; however, force levels showed little dependence on fuel pressure or altitude in contrast to control volume analysis predictions. Various facility interference mechanisms and scaling issues were studied and are discussed.
Shock-wave boundary-layer interactions (SWBLI) pose unique challenges for the slender airframes and sharp control surfaces characteristic of high-speed airbreathing aircraft. Spikes in pressure and thermal loading have been shown to occur in SWBLI regions; thus, predicting their location and behavior proves critical for assuring aircraft structural integrity and fatigue resilience. SWBLIs frequently lead to severe turbulent boundary-layer separation and corresponding unsteady motions characterized by a wide range of frequencies. Low-frequency motion has been shown to couple with the structure of a compliant panel, and turbulent boundary layers thus present a particular danger for thin control surfaces. Previous studies have shown that the thermal loading on a compliant panel in a ramp-induced SWBLI may have a signi cant impact on the panel vibrations. A multitude of studies has investigated the heating on rigid structures, but a charactrization of the heating effects on compliant structures is necessary to fully understand the fluid-thermal-structural interactions (FTSI) occurring in ramp-induced SWBLIs. This studuses infrared thermography and high-frequency Kulite pressure transducers to examine the heating loads on rigid and compliant ramps at various angles and flow conditions at Mach 6.