Search NASA⌕ Search

SEARCH · Search NASA

Results for “Rate formulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

DEHBA (di-2-ethylhexylbutyramide) gamma radiolysis under spent nuclear fuel solvent extraction process conditions

Di-2-ethylhexylbutyramide (DEHBA) has been presented as part of a hydro-reprocessing solvent extraction system for the co-extraction of uranium and plutonium from spent nuclear fuel. Yet, there remains a lack of quantitative understanding of the impact of chemical environment on the radiation chemistry of DEHBA, especially under conditions expected in real-world solvent extraction processes. Therefore, we have undertaken a systematic investigation into the radiolytic degradation of DEHBA in n-dodecane under fully aerated and biphasic conditions. DEHBA integrity and degradation product formation were measured for both extraction (in contact with 4.0 M HNO 3(aq) ) and stripping (in contact with 0.1 M HNO 3(aq) ) formulations. At the lower acidity the rate of DEHBA/n-dodecane degradation was slow (G = -0.26 ± 0.02 µM J -1 ) whereas at the higher acidity this degradation was about 35% faster (G = -0.35 ± 0.02 µM J-1). Both values were much less than analogous measurements under deaerated conditions. Under continuously aerated conditions, FTIR and ESI-MS measurements identified the two major degradation products, bis-2-ethylhexylamine (b2EHA) and N-(2-ethylhexyl)butyramide (MEHBA), as well as the presence of additional oxidized product species. Solvent system performance was also investigated using uranium extraction and strip distribution ratio measurements. These reports showed that there was only minimal change in uranium extraction and stripping performance with absorbed gamma dose.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Invigoration or Enervation of Convective Clouds by Aerosols?

Are convective clouds strengthened by the addition of aerosol particles? We present new theoretical calculations which starkly contrast previous results. Prior foundational work suggested that aerosols strongly invigorate convective cloud updrafts via changes to cold-phase processes. We show that the peak magnitude of invigoration by this mechanism is substantially reduced for cold-based storms. For warm-based storms, the updrafts are weakened, not strengthened, by aerosol-induced changes to cold-phase processes. Our calculations show that if invigoration occurs, it is driven primarily by changes to warm-phase processes and may be largest well before the storm reaches maturity. The calculations are based on a new formulation of the moist adiabatic lapse rate that accounts for freezing, supersaturation, and condensate loading. The results significantly reshape our understanding of the impact of aerosols on convective updrafts.

58 GEOSCIENCES↗

A Numerical Modeling Framework for Flocculation and Cohesive Sediment Transport in the Wave Bottom Boundary Layer

Flocculation, a critical process in coastal and estuarine systems, plays a significant role in sediment transport, nutrient cycling, and ecological health. This study develops a cohesive sediment transport modeling framework tailored to the wave bottom boundary layer under dilute and equilibrium conditions, explicitly incorporating flocculation effects via a Population Balance Equation (PBE). Using Direct Numerical Simulation, six baseline cases, each with a distinct sediment concentration profile resulting from a constant settling velocity and critical erosion shear stress, are generated to drive the PBE flocculation model for given floc yield strength and stickiness. Results reveal that flocculation significantly influences sediment concentration profiles promoting three distinct stages, well‐mixed, transition to lutocline, and well‐developed lutocline. At low concentrations with well‐mixed profiles, cohesive floc properties are less significant, and turbulence is a main flocculation driver. In contrast, as concentration increases, cohesive floc properties become crucial, facilitating lutocline formation. Here, the analysis also highlights limitations of depth‐averaged settling velocity as a parameterization. It is suitable for well‐mixed and transitional profiles but fails in well‐developed lutoclines, where empirical formulations that explicitly incorporate turbulent shear rate and sediment concentration better capture variability. This study underscores the necessity of incorporating flocculation effects into sediment transport models to enhance predictions of sediment dynamics in wave bottom boundary layers.

Penaloza‐Giraldo, Jorge A. [Oak Ridge National Lab↗

Stabilization of pressure-driven magnetohydrodynamic modes by separatrix in dipole plasma confinement

The eigenvalue problem is solved for the short-wavelength pressure-driven magnetohydrodynamic modes in configuration with closed magnetic field lines in the poloidal direction. Here we show that the magnetic separatrix (which determines the boundary of the confinement region) provides a substantial stabilizing effect by which the total volume inside the separatrix becomes stable even for very high beta values. The plasma inertia and compressibility are properly formulated to give the correct growth rate of the mode.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Reliability-Informed Economic and Energy Evaluation for Design for Remanufacturing: A Case Study on a Hydraulic Manifold

Design for Remanufacturing (DfRem) is an attractive approach for sustainable product development. Evaluation of DfRem strategies, from both economic and environmental perspectives, at an early design stage can allow the designers to make informed decisions when choosing the best design option. Studying the long-term implications of a particular design scenario requires quantifying the benefits of remanufacturing for multiple life cycles while considering the reliability of the product. In addition to comparing designs on a one-to-one basis, we find that including reliability provides a different insight into comparing design strategies. We present a reliability-informed cost and energy analysis framework that accounts for product reliability for multiple remanufacturing cycles within a certain warranty policy. The variation of reuse rate over successive remanufacturing cycles is formulated using a branched power-law model which provides probabilistic scenarios of reusing or replacing with new units. To demonstrate the utility of this framework, we use the case study of a hydraulic manifold, which is a component of a transmission used in some agricultural equipment, and use real-world field reliability data to quantify the transmission’s reliability. Three design improvement changes are proposed for the manifold and we quantify the costs and energy consumption associated with each of the design changes for multiple remanufacturing cycles.

design for remanufacturing↗

A novel physics-based and data-supported microstructure model for part-scale simulation of laser powder bed fusion of Ti-6Al-4V

The elasto-plastic material behavior, material strength and failure modes of metals fabricated by additive manufacturing technologies are significantly determined by the underlying process-specific microstructure evolution. In this work a novel physics-based and data-supported phenomenological microstructure model for Ti-6Al-4V is proposed that is suitable for the part-scale simulation of laser powder bed fusion processes. The model predicts spatially homogenized phase fractions of the most relevant microstructural species, namely the stable β-phase, the stable α s -phase as well as the metastable Martensite α m -phase, in a physically consistent manner. In particular, the modeled microstructure evolution, in form of diffusion-based and non-diffusional transformations, is a pure consequence of energy and mobility competitions among the different species, without the need for heuristic transformation criteria as often applied in existing models. The mathematically consistent formulation of the evolution equations in rate form renders the model suitable for the practically relevant scenario of temperature- or time-dependent diffusion coefficients, arbitrary temperature profiles, and multiple coexisting phases. Due to its physically motivated foundation, the proposed model requires only a minimal number of free parameters, which are determined in an inverse identification process considering a broad experimental data basis in form of time-temperature transformation diagrams. Subsequently, the predictive ability of the model is demonstrated by means of continuous cooling transformation diagrams, showing that experimentally observed characteristics such as critical cooling rates emerge naturally from the proposed microstructure model, instead of being enforced as heuristic transformation criteria. Eventually, the proposed model is exploited to predict the microstructure evolution for a realistic selective laser melting application scenario and for the cooling/quenching process of a Ti-6Al-4V cube of practically relevant size. Numerical results confirm experimental observations that Martensite is the dominating microstructure species in regimes of high cooling rates, e.g., due to highly localized heat sources or in near-surface domains, while a proper manipulation of the temperature field, e.g., by preheating the base-plate in selective laser melting, can suppress the formation of this metastable phase.

Inverse parameter identification↗

M3MS-19IN0101201 Modeling Intra-granular Fission Gas Bubble Evolution in Uranium Dioxide during Transients

The SciDAC milestone M3MS-19IN0101201 on Modeling Intra-granular Fission Gas Bubble Evolution in Uranium Dioxide during Transients was completed with the development, testing and implementation in the Bison code of an engineering model for intra-granular fission gas bubble evolution that is applicable to transient conditions. The model extends the previous work on modeling bubble evolution during normal operating conditions to include additional complexity that arises during transient situations, in particular, the so-called intra-granular bubble coarsening. This phenomenon refers to the appearance of a second population of coarsened bubbles with diameters of tens to hundreds of nm, which co-exist with nanometric bubbles present also during normal operating conditions and are responsible for a large portion of transient fuel swelling. The developed model considers growth of bubbles along dislocations, associated with the absorption of vacancies available in the dislocation core region, and favored by pipe diffusion of fission gas atoms. The model also utilizes the formulation for the gas atom resolution rate developed in the present SciDAC project through molecular dynamics simulations by other institutions. The present work therefore demonstrates an operational multiscale approach, based on collaboration within the project. The model is validated to an extensive experimental dataset of ramp tested uranium dioxide fuel samples. Additionally, we present new applications of the base model for bubble evolution during normal operating conditions to Bison engineering simulations of Cr2O3-doped fuel rods irradiated in the Halden reactor. Simulation results in terms of integral fission gas release in the fuel rods are compared to the available experimental data, pointing out significant improvements in the engineering predictions compared to application of the empirical model that was available in Bison before the SciDAC developments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A virtual element generalization on polygonal meshes of the Scott-Vogelius finite element method for the 2-D Stokes problem

The virtual element method (VEM) is a Galerkin approximation method that extends the finite element method to polytopal meshes. In this paper, we present a conforming formulation that generalizes the Scott-Vogelius finite element method (FEM) for the numerical approximation of the Stokes problem to polygonal meshes in the framework of the virtual element method. In particular, we consider a straightforward application of the virtual element approximation space for scalar elliptic problems to the vector case and approximate the pressure variable through discontinuous polynomials. We assess the effectiveness of the numerical approximation by investigating the convergence on a manufactured solution problem and a set of representative polygonal meshes. We numerically show that this formulation is convergent with optimal convergence rates except for the lowest-order case on triangular and square meshes where the method coincides with the P 1 - P 0 Scott-Vogelius scheme, which is well-known to be unstable.

97 MATHEMATICS AND COMPUTING↗

A virtual element generalization on polygonal meshes of the Scott-Vogelius finite element method for the 2-D Stokes problem

The Virtual Element Method (VEM) is a Galerkin approximation method that extends the Finite Element Method (FEM) to polytopal meshes. In this paper, we present a conforming formulation that generalizes the Scott-Vogelius finite element method for the numerical approximation of the Stokes problem to polygonal meshes in the framework of the virtual element method. In particular, we consider a straightforward application of the virtual element approximation space for scalar elliptic problems to the vector case and approximate the pressure variable through discontinuous polynomials. We assess the effectiveness of the numerical approximation by investigating the convergence on a manufactured solution problem and a set of representative polygonal meshes. Finally, we numerically show that this formulation is convergent with optimal convergence rates except for the lowest-order case on triangular meshes, where the method coincides with the $\mathbb{P}_1$ – $\mathbb{P}_0$ Scott-Vogelius scheme, and on square meshes, which are situations that are well-known to be unstable.

97 MATHEMATICS AND COMPUTING↗

Peculiarities of the critical dynamics in magnetically uniaxial PbFe{sub 12}O{sub 19} hexaferrite

The conditions under which the thermodynamic theory of the critical slowing-down of the order parameter relaxation rate describes the behavior of magnetically uniaxial crystals are formulated. Taking into account the formulated conditions, the peculiarities of the dynamic magnetic susceptibility and the critical slowing-down of the magnetization relaxation rate of PbFe{sub 12}O{sub 19} in the vicinity of the Curie temperature are studied. The obtained experimental results agree well with the droplet model of phase transitions. Based on the experimental data, an estimated value of the correlation length for the magnetization in the temperature area of the critical slowing-down of the relaxation rate is obtained within the droplet model.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Bubble departure and sliding in high-pressure flow boiling of water

Bubble growth, departure and sliding in low-pressure flow boiling has received considerable attention in the past. However, most applications of boiling heat transfer rely on high-pressure flow boiling, for which very little is known, as experimental data are scarce and very difficult to obtain. In this work, we conduct an experiment using high-resolution optical techniques. By combining backlit shadowgraphy and phase-detection imaging, we track bubble shape and physical footprint with high spatial ($6\,\mathrm {\mu }{\rm m}$) and temporal ($33\,\mathrm {\mu }{\rm s}$) resolutions, as well as bubble size and position as bubbles nucleate and slide on top of the heated surface. We show that at pressures above 1 MPa bubbles retain a spherical shape throughout the growth and sliding process. We analytically derive non-dimensional numbers to correlate bubble velocity and liquid velocity throughout the turbulent boundary layer and predict the sliding of bubbles on the surface, solely from physical properties and the bubble growth rate. We also show that these non-dimensional solutions can be leveraged to formulate elementary criteria that predict the effect of pressure and flow rate on bubble departure diameter and growth time.

Mechanics↗

Teaching Nonradiative Transitions with MATLAB and Python

Nonradiative transitions are changes in energy states of atoms, ions, or molecules that do not involve the emission or absorption of photons. Despite their importance in understanding luminescent properties and photochemical reaction mechanisms, nonradiative transitions are rarely given more than a qualitative overview in undergraduate and even graduate physical chemistry curricula. To supplement the coverage of nonradiative transition topics, we provide here a set of active learning exercises to help students develop an intuitive understanding of the factors that determine the rate of nonradiative transitions. Here, we start by outlining the theoretical background through the formulations of the Franck–Condon factor and its relation to the rate of nonradiative transition. We then introduce three teaching modules, with associated MATLAB and Python codes, to explore how (1) the excited state nuclear displacement, (2) the electronic energy gap between excited and ground state and (3) the excited/ground state vibrational mode frequencies affect the magnitude of the Franck–Condon factor and thereby the rate of nonradiative transitions. The wave function overlap plots that accompany all teaching modules provide direct visualization of the effect of input parameters on the magnitude of Franck–Condon overlap integral.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Using Data Science Tools to Reveal and Understand Subtle Relationships of Inhibitor Structure in Frontal Ring-Opening Metathesis Polymerization

The rate of frontal ring-opening metathesis polymerization (FROMP) using the Grubbs generation II catalyst is impacted by both the concentration and choice of monomers and inhibitors, usually organophosphorus derivatives. Herein we report a data-science-driven workflow to evaluate how these factors impact both the rate of FROMP and how long the formulation of the mixture is stable (pot life). Using this workflow, we built a classification model using a single-node decision tree to determine how a simple phosphine structural descriptor (V bur-near ) can bin long versus short pot life. Additionally, we applied a nonlinear kernel ridge regression model to predict how the inhibitor and selection/concentration of comonomers impact the FROMP rate. Furthermore, the analysis provides selection criteria for material network structures that span from highly cross-linked thermosets to non-cross-linked thermoplastics as well as degradable and nondegradable materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

How Radiation Oncologists Evaluate and Incorporate Life Expectancy Estimates Into the Treatment of Palliative Cancer Patients: A Survey-Based Study

Purpose: We surveyed how radiation oncologists think about and incorporate a palliative cancer patient’s life expectancy (LE) into their treatment recommendations. Methods and Materials: A 41-item survey was e-mailed to 113 radiation oncology attending physicians and residents at radiation oncology centers within the Boston area. Physicians estimated how frequently they assessed the LE of their palliative cancer patients and rated the importance of 18 factors in formulating LE estimates. For 3 common palliative case scenarios, physicians estimated LE and reported whether they had an LE threshold below which they would modify their treatment recommendation. LE estimates were considered accurate when within the 95% confidence interval of median survival estimates from an established prognostic model. Results: Among 92 respondents (81%), the majority were male (62%), from an academic practice (75%), and an attending physician (70%). Physicians reported assessing LE in 91% of their evaluations and most frequently rated performance status (92%), overall metastatic burden (90%), presence of central nervous system metastases (75%), and primary cancer site (73%) as “very important” in assessing LE. Across the 3 cases, most (88%-97%) had LE thresholds that would alter treatment recommendations. Overall, physicians’ LE estimates were 22% accurate with 67% over the range predicted by the prognostic model. Conclusions: Physicians often incorporate LE estimates into palliative cancer care and identify important prognostic factors. Most have LE thresholds that guide their treatment recommendations. However, physicians overestimated patient survival times in most cases. Future studies focused on improving LE assessment are needed.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Advanced High-Level Waste Glass Research and Development Plan

The U.S. Department of Energy Office of River Protection (ORP) has implemented an integrated program to increase the loading of Hanford tank wastes in glass while meeting melter lifetime expectancies and process, regulatory, and product quality requirements. The integrated ORP program is focused on providing a technical, science-based foundation from which key decisions can be made regarding the successful operation of the Hanford Tank Waste Treatment and Immobilization Plant (WTP) facilities. The fundamental data stemming from this program will support development of advanced glass formulations, key process control models, and tactical processing strategies to ensure safe and successful operations for both the low-activity waste (LAW) and high-level waste (HLW) vitrification facilities with an appreciation toward reducing overall mission life. The purpose of this advanced HLW glass research and development plan is to identify the near-, mid-, and longer-term research and development activities required to develop and validate advanced HLW glasses and their associated models to support facility operations at WTP, including both direct feed and full pretreatment flowsheets. This plan also integrates technical support of facility operations and waste qualification activities to show the interdependence of these activities with the advanced waste glass (AWG) program to support the full WTP mission. Figure ES-1 shows these key ORP programmatic activities and their interfaces with both WTP facility operations and qualification needs. The plan is a living document that will be updated to reflect key advancements and mission strategy changes. The research outlined here is motivated by the potential for substantial economic benefits (e.g., significant increases in waste throughput and reductions in glass volumes) that will be realized when advancements in glass formulation continue and models supporting facility operations are implemented. Developing and applying advanced glass formulations will reduce the cost of Hanford tank waste management by reducing the schedule for tank waste treatment and reducing the amount of HLW glass for storage, transportation, and disposal. Additional benefits will be realized if advanced glasses are developed that demonstrate more tolerance for key components in the waste (such as Al 2 O 3 , Cr 2 O 3 , SO 3 and Na 2 O) above the currently defined WTP constraints. Tolerating these higher concentrations of key waste loading limiters may reduce the burden on (or even eliminate the need for) leaching to remove Cr and Al and washing to remove excess S and Na from the HLW fraction. Advanced glass formulations may also make direct vitrification of the HLW fraction without significant pretreatment more cost effective. Finally, the advanced glass formulation efforts seek not only to increase waste loading in glass, but also to increase glass production rate. When coupled with higher waste loading, ensuring that all of the advanced glass formulations are processable at or above the current contract processing rate leads to significant improvements in waste throughput (the amount of waste being processed per unit time),which could significantly reduce the overall WTP mission life. The integration of increased waste loading, reduced leaching/washing requirements, and improved melting rates provides a system-wide approach to improve the effectiveness of the WTP process.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Improved MAGIC gel for higher sensitivity and elemental tissue equivalent 3D dosimetry

Purpose: Polymer-based gel dosimeter (MAGIC type) is a preferable phantom material for PET range verification of proton beam therapy. However, improvement in elemental tissue equivalency (specifically O/C ratio) is very desirable to ensure realistic time-activity measurements. Methods: Glucose and urea was added to the original MAGIC formulation to adjust the O/C ratio. The dose responses of the new formulations were tested with MRI transverse relaxation rate (R2) measurements. Results: The new ingredients improved not only the elemental composition but also the sensitivity of the MAGIC gel. The O/C ratios of our new gels agree with that of soft tissue within 1%. The slopes of dose response curves were 1.6-2.7 times larger with glucose. The melting point also increased by 5 deg. C. Further addition of urea resulted in a similar slope but with an increased intercept and a decreased melting point. Conclusions: Our improved MAGIC gel formulations have higher sensitivity and better elemental tissue equivalency for 3D dosimetry applications involving nuclear reactions.

61 RADIATION PROTECTION AND DOSIMETRY↗

Incorporating point defect generation due to jog formation into the vector density-based continuum dislocation dynamics approach

During plastic deformation of crystalline materials, point defects such as vacancies and interstitials are generated by jogs on moving dislocations. A detailed model for jog formation and transport during plastic deformation was developed within the vector density-based continuum dislocation dynamics framework. Here as a part of this model, point defect generation associated with jog transport was formulated in terms of the volume change due to the non-conservative motion of jogs. Balance equations for the vacancies and interstitials including their rate of generation due to jog transport were also formulated. A two-way coupling between point defects and dislocation dynamics was then completed by including the stress contributed by the eigen-strain of point defects. A jog drag stress was further introduced into the mobility law of dislocations to account for the energy dissipation during point defects generation. A number of test problems and a fully coupled simulation of dislocation dynamics and point defects generation and diffusion were performed. The results show that there is an asymmetry of vacancy and interstitial generation due to the different formation energies of the two types of defects. The results also show that a higher hardening rate and a higher dislocation density are obtained when the point defect generation mechanism is coupled to dislocation dynamics.

36 MATERIALS SCIENCE↗

A rheological model for loose sands with insights from DEM

A rheological model for loose granular media is developed to capture both solid-like and fluid-like responses during shearing. The proposed model is built by following the mathematical structure of an extended Kelvin–Voigt model, where an elastic spring and plastic slider act in parallel to a viscous damper. This arrangement requires the partition of the total stress into rate-independent and rate-dependent stress components. To model the solid-like behavior, a simple frictional plasticity model is adopted without modifications, thus contributing to the rate-independent stress. Instead, the fluid-like or rate-dependent stress is further decomposed into deviatoric and volumetric parts, by proposing a new formulation based on a combination of the μ(I) relation, originally developed under pressure-controlled shear, with a pressure-shear rate relation derived under volume-controlled shear. The proposed formulation allows the model to capture both the increase in the friction coefficient and the enhanced dilation at high shear rates. High-fidelity simulation data, obtained from discrete element method and multiscale modelling, are used to evaluate the performance of the proposed constitutive model. The model provides accurate results under both drained and undrained simple shear paths across a wide range of shear rates. Furthermore, it successfully reproduces at much lower computational cost the flowslide mobility computed through multiscale simulations, which is primarily regulated by the shear rate dependence of the material properties during the dynamic runout stage.

Elasticity↗