SEARCH · Search NASA

Results for “Reactivity Control System”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

DOE OSTI2025

Dynamics modeling of molten salt reactor with reduced and expanded representations of delayed neutron precursors

Molten salt reactors (MSRs) present unique challenges in dynamic behavior due to the mobility of their fuel. In these reactors, delayed neutron precursors (DNPs) drift with the fuel circulation through the primary loop. As a result, a fraction of DNPs decays outside the core, effectively reducing the available delayed neutron population for reactivity control. Consequently, precise modeling of the distribution and behavior of DNPs is critical for accurate reactor dynamics simulations. In this study, the System Dynamics Analysis Tool (SDAT) was used to simulate a thermal-spectrum MSR under steady-state conditions and following transients. The effects of using reduced and expanded representations of DNPs with fewer or more groups than the conventional 6-group model were investigated. Their impact on the simulated distribution of precursors in the primary loop, reactivity loss value, and reactor response to transients was analyzed. Simulation results showed that reduced models lead to the loss of the actual DNPs distribution data, resulting in less accurate estimates of reactivity loss. Reactor power predictions using these reduced models showed significant deviations compared to those using the conventional 6-group model in transient simulations. Expanded models offered a more accurate representation of the distribution of DNPs and reactivity loss estimates. Reactor power predictions using expanded models showed minimal deviation from the conventional 6-group model during the simulated transients.

analysis↗

DOE OSTI2022

Transmission-distribution long-term volt-var planning considering reactive power support capability of distributed PV

High penetration of grid-edge, inverter-based photovoltaic (PV) can cause significant voltage fluctuations not only at the distribution but also at the sub-transmission levels due to PV output intermittency. Traditional reactive power planning approaches do not consider intermittency, nor the possibility of coordinating the control of existing and future volt-ampere reactive resources. This paper proposes a reactive power planning tool for sub-transmission systems to mitigate voltage violations and fluctuations caused by high PV penetration and intermittency with a minimum investment cost. The planning tool coordinates with an optimization-based volt-var operational tool for: a) modeling the coordination of all existing var assets in both sub-transmission and distribution systems to reduce the need of new equipment, and b)selecting a set of scenarios with voltage violations, derived from PV intermittency c) testing the final investment decision. The tool obtains an investment need for each intermittency scenario with a proposed optimal power-flow framework with efficient techniques to handle a high number of discrete variables. Two options are provided for final planning decision: i) a conservative direct combination of investment need solutions and ii) a machine learning-based selection of representative investment needs at most time steps. The final investment decision options are verified using a realistic large-scale sub-transmission system and 5-minute PV and load data. The results show a significant voltage performance improvement with a lower investment cost for additional var equipment compared to conventional approaches.

14 SOLAR ENERGY↗

DOE OSTI2022

Cooling-induced reactivation of distant faults during long-term geothermal energy production in hot sedimentary aquifers

Deep geothermal energy (DGE) represents an opportunity for a sustainable and carbon-free energy supply. One of the main concerns of DGE is induced seismicity that may produce damaging earthquakes, challenging its widespread exploitation. It is widely believed that the seismicity risk can be controlled by using doublet systems circulating water to minimize the injection-induced pressure changes. However, cold water reinjection may also give rise to thermal stresses within and beyond the cooled region, whose potential impacts on fault reactivation are less well understood. Here, we investigate by coupled thermo-hydro-mechanical modeling the processes that may lead to fault reactivation in a hot sedimentary aquifer (HSA) in which water is circulated through a doublet. We show that thermal stresses are transmitted much ahead of the cooled region and are likely to destabilize faults located far away from the doublet. Meanwhile, the fault permeability mainly controls the fault reactivation timing, which entails the importance of employing appropriate characterization methods. This investigation is crucial for understanding the mechanisms controlling induced seismicity associated with DGE in a HSA and allows the success of future DGE projects.

15 GEOTHERMAL ENERGY↗

DOE OSTI2023

Novel gas exposure system for the controlled exposure of plants to gaseous hydrogen fluoride

Abstract Plants can serve as sensitive bioindicators of the presence of contaminant vapors in the atmosphere. This work describes a novel laboratory-based gas exposure system capable of calibrating plants as bioindicators for the detection and delineation of the atmospheric contaminant hydrogen fluoride (HF) as a preparatory step for monitoring release emissions. To evaluate changes in plant phenotype and stress-induced physiological effects attributed to HF alone, the gas exposure chamber must have additional controls to simulate otherwise optimal plant growth conditions including variables such as light intensity, photoperiod, temperature, and irrigation. The exposure system was designed to maintain constant growth conditions during a series of independent experiments that varied between optimal (control) and stressful (HF exposure) conditions. The system was also designed to ensure the safe handling and application of HF. An initial system calibration introduced HF gas into the exposure chamber and monitored HF concentrations by cavity ring-down spectroscopy for a 48-h period. Stable concentrations inside the exposure chamber were observed after approximately 15 h, and losses of HF to the system ranged from 88 to 91%. A model plant species ( Festuca arundinacea ) was then exposed to HF for 48 h. Visual phenotype stress-induced responses aligned with symptoms reported in the literature for fluoride exposure (tip dieback and discoloration along the dieback transition margin). Fluoride concentrations in exposed tissues compared to control tissues confirmed enhanced fluoride uptake due to HF exposure. The system described herein can be applied to other reactive atmospheric pollutants of interest in support of bioindicator research.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2024

Polymer Layer-Accelerated CO 2 Absorption in Aqueous Amino Acid Solutions

Direct air capture (DAC) of CO 2 via solvent-based absorption is considered a promising negative-emission technology. However, the low concentration of CO 2 in the air and slow transport into the solvent make DAC notoriously challenging to implement without costly investments. In this study, we explore the fundamental role that the bulk and surface properties of CO 2 -permeable polymer membranes play in enhancing the efficiency of the solution sorption process in passive DAC of CO 2 . This work leverages various spectroscopic and computational studies to demonstrate that a hybrid system, comprising a reusable CO 2 -permeable polymer layer placed atop an aqueous amino acid (AA) solution, can outperform a pure aqueous AA system by 2-fold. Here we show how the enhanced solubility of CO 2 in the polymer layer can improve the transport of CO 2 into the aqueous phase, while the chemistry of the polymer can control the interfacial barrier for CO 2 permeation and the interfacial concentration of reactive AAs. The derived knowledge of the material properties achieved here can aid in the design of DAC systems with improved performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Hardware Demonstration of Weak Grid Oscillations in Grid-Following Converters

The increasing penetration of inverter-based resources (IBRs) introduces some unexpected dynamic issues, including low-frequency oscillations. In this paper, a laboratory-scale grid-following voltage-source converter (VSC) system is implemented to demonstrate weak grid oscillations. Grid-following control is applied in VSC to provide active power, reactive power or ac voltage control. The test bed is also replicated in electromagnetic transient (EMT) simulation environment (MAT-LAB/SimPowerSystems) for benchmark purpose. Case studies are carried out to demonstrate low-frequency oscillations under real power/ac voltage or real power/reactive power control. The excellent agreement between the simulation and experimental results ensures that the two test beds are exchangeable and can be used for testing oscillation mitigation strategies in future research.

Bao, Li↗

DOE OSTI2024

Positive-Sequence Modeling of Droop-Controlled Grid-Forming Inverters for Transient Stability Simulation of Transmission Systems

Here, this paper describes a positive-sequence model to represent two widely reported droop-controlled grid-forming inverters for bulk power systems simulation study. Methods of how to develop the equivalent voltage source behind impedance to represent inverters with and without inner control loops, modeling of P-f and Q-V droop controls, active and reactive power limiting modeling, and modeling of fault current limiting controls are described in detail. The model is implemented in commercially available positive-sequence simulation tools and compared with detailed electromagnetic transient models in both a single-grid-forming-inverter infinite-bus system and a modified IEEE 39-bus system. Finally, the model is tested on the full US Western Electricity Coordinating Council (WECC) system. Study results show that the model has a good level of accuracy compared to the detailed EMT models, and at the same time also achieves a high computational efficiency, which is suitable for the bulk power system simulation study.

42 ENGINEERING↗

DOE OSTI2021

Exploring the Effects of Piston Bowl Geometry and Injector Included Angle on Dual-Fuel and Single-Fuel RCCI

Abstract Reactivity control compression ignition (RCCI) is a low-temperature combustion technique that has been proposed to meet the current demand for high thermal efficiency and low engine-out emissions. However, its requirement of two separate fuel systems (i.e., a low-reactivity fuel system and a high-reactivity fuel system) has been one of its major challenges in the last decade. This leads to the single-fuel RCCI concept, where the secondary fuel (reformates of diesel) is generated from the primary fuel (diesel) through catalytic partial oxidation reformation. Following the in-depth analysis of the reformate fuel (reformates of diesel) and its benefit as the low-reactivity fuel with diesel, the effects of the start of injection (SOI) timing of diesel and the energy-based blend ratio were also studied in detail. In this study, the effects of piston profile and the injector included angles were experimentally examined using both conventional fuel pairs (gasoline—diesel and natural gas—diesel) and reformate RCCI. A validated computational fluid dynamics (CFD) model was also used for a better understanding of the experimental trends. Comparing a reentrant bowl piston with a shallow bowl piston at a constant compression ratio and SOI, the latter showed better thermal efficiency, regardless of the fuel combination, due to its 10% lower surface area for the heat transfer. Comparing the 150-degree included angle and 60-degree included angle on the shallow bowl piston, the latter showed better combustion efficiency, regardless of the fuel combination, due to its earlier combustion phasing (at constant SOI timing). The effect was particularly prominent on reformate RCCI because of its incredibly high diluent concentration, which retards the combustion further for the 150-deg injector. Later, using convergecfd, seven different injector included angles were studied at a constant SOI. With the change in injector included angle, the region of the cylinder targeted by the fuel spray varies significantly, and it was found to have a significant impact on the combustion efficiency and the engine-out emissions. As the injector included angle changed from 60-deg to 150-deg, the combustion efficiency increased by 15% and the CO, NOx, and HC emissions decreased by 96%, 70%, and 86%, respectively.

Engineering↗

DOE OSTI2022

Modeling of the TRIGA IPR-R1 research reactor with the Serpent2/RINNOVO Nodal core analysis package

The Serpent2/RINNOVO nodal core analysis code system, a dedicated tool for modeling research reactors, has the capability to accurately predict important core physics parameters involved in the safety of reactor operation, such as various reactivity coefficients, control rod and bank worths including the shutdown margin, power distributions as well as local neutron flux predictions at various core locations of high importance, e.g., at irradiation rigs. In this work, a hexagonal model of the unrodded initial core of the Brazilian IPR-R1 Mark I type TRIGA nuclear reactor has been created using the Serpent2/RINNOVO code system. The choice of employing a hexagonal core geometry representation has mainly been made to facilitate subsequent fuel shuffling operations and core follow calculations of this reactor. Numerical results in terms of the core eigenvalue and the assembly power distribution have then been compared against corresponding full core Serpent2 results to prove feasibility of using the Serpent2/RINNOVO code system for modeling small and highly heterogeneous TRIGA reactors. Overall, RINNOVO predicts the power distribution very accurately but the eigenvalue error still remains quite large. In light of being the very first evaluation of a TRIGA reactor with the RINNOVO nodal core simulator, these results are also considered to be very preliminary. Improved accuracy is expected by incorporating a proper methodology in the current code system for computing discontinuity factors for multi-assembly configurations. Furthermore, improved results are expected by increasing the number of energy groups used by RINNOVO in these core calculations.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2024

An Innovative Energy Management System for Microgrids with Multiple Grid-Forming Inverters

As increasingly more grid-forming (GFM) inverter-based resources replace traditional fossil-fueled synchronous generators as the GFM sources in microgrids, the existing microgrid energy management systems (EMS) need to be updated to control and coordinate multiple GFM inverters that consider system control objectives under different microgrid connection states. For each state, we formulate an optimization problem and apply a real-time feedback-based control algorithm; altogether, the control algorithms seamlessly connect the states into a generic microgrid EMS that controls the nodal voltages and frequencies, becomes a virtual power plant (VPP) when connected to the main grid, and coordinates power sharing responsibility among GFM sources when islanded. We showcase the EMS on a real-world simulation of a microgrid under the different states to demonstrate its operational effectiveness.

energy management systems↗

DOE OSTI2024

Pore architecture controls on mineral reactivity

Mineral dissolution rates measured in natural environments are much slower than those measured in laboratory settings. This project tested the hypothesis that the way fluid flows through rocks in natural systems creates areas where mineral dissolution is fast and areas where mineral dissolution is slow. This hypothesis was tested with a combination of laboratory experiments and numerical simulation. We demonstrated a separation of fluid flow pathways and rates of mineral dissolution in laboratory experiments for the first time using an experimental approach where we created synthetic rocks that have different ratios of connected and dead-end pathways for fluid flow. In laboratory experiments with higher proportions of dead-end pathways, the mineral dissolution rates were slower. We found that where fluid flows through connected pathways the continuous refreshing of fluid at the mineral surface creates conditions where dissolution is fast. In contrast, where fluid either flows slowly through poorly connected pathways or is stagnant in dead-end pathways, mineral dissolution is slow. The results from this project suggest that the overall slowing of rates of mineral dissolution is important when the proportion of dead-end pathways is greater than ~40%. This project informs our understanding of the way that fluids react with rocks in carbon dioxide sequestration and enhanced geothermal projects where fluids are purposefully injected into rocks for energy applications.

58 GEOSCIENCES↗

DOE OSTI2025

Permeate fluxes from desalination of brines and produced waters: A reactive transport modeling study

The increasing interest in the use of membrane systems to desalinate inland brackish water, agricultural drainage, and industrially produced wastewater demands improved means of predicting desalination system performance under variable feedwater compositions. The interaction among water flow, solute transport, and chemical composition in these systems impacts permeate flux evolution. Here, an established multicomponent reactive transport simulator that accounts for these coupled processes is applied to compute osmotic pressure and permeate fluxes in reverse osmosis (RO) systems. The model is first validated by predicting permeate fluxes for a set of benchtop crossflow experiments subject to a range of feed flow rates and compositions, under fouling and non-fouling conditions. Results compare favorably with measured data that show that solutions with similar total dissolved solids concentrations but different compositions result in different permeate fluxes. The model is then applied to predict permeate fluxes from the desalination of produced waters using a commercial spiral wound RO module. For NaCl-dominant brines, at total dissolved salt concentrations (TDS) below about 70 g/L, permeate fluxes are inversely proportional to water mole fraction as the latter is a reasonable approximation of water activity (i.e. ideal mixing). In the case of Ca–Cl-, Na–CO3- and Na–SO4-dominant brines below about 70 g/L TDS, this relationship does not hold as well and tends to overpredict osmotic pressure and thus underpredict permeate fluxes. However, the opposite becomes true at higher TDS values for typical produced waters. The scaling potential of these waters is also computed by allowing the precipitation of minerals above their saturation limit on the RO membrane. This work demonstrates how reactive transport models developed for the analysis of waters from geological systems can be extended to improve process design, optimization, and control in desalination systems from produced waters and beyond.

Molins, Sergi↗

DOE OSTI2025

Improving photovoltaic hosting capacity of distribution networks with coordinated inverter control: A case study of the EPRI J1 feeder

Abstract Adding photovoltaic (PV) systems in distribution networks, while desirable for reducing the carbon footprint, can lead to voltage violations under high solar‐low load conditions. The inability of traditional volt‐VAr control in eliminating all the violations is also well‐known. This article presents a novel coordinated inverter control methodology that leverages system‐wide situational awareness to significantly improve hosting capacity (HC). The methodology employs a real‐time voltage‐reactive power (VQ) sensitivity matrix in an iterative linear optimizer to calculate the minimum reactive power intervention from PV inverters needed for mitigating over‐voltage without resorting to active power curtailing or requiring step voltage regulator setting changes. The algorithm is validated using the EPRI J1 feeder under an extensive set of realistic use cases and is shown to provide 3x improvement in HC under all scenarios.

Dalal, Dhaval [School of Electrical, Computer, and↗

DOE OSTI2022

SAS4A/SASSYS-1 Validation with EBR-II Tests Performed During the SHRT Testing Program

The EBR-II sodium-cooled fast reactor supported a wide range of fast reactor research activities. The final fifteen years of operations at EBR-II were used for experiments and tests to demonstrate the importance of passive safety in liquid metal reactors and the capability of such systems to provide strong passive responses during off-normal conditions. The Shutdown Heat Removal Test program at EBR-II provided test data supporting the validation of computer codes for design, licensing, and operation of LMRs, among other objectives. The program included nearly sixty tests, most of which were protected and unprotected loss of flow and loss of heat sink tests run at various initial powers and flow rates. This report documents the results of modeling and simulation of tests from the Shutdown Heat Removal Test program to support validation of Argonne’s SAS4A/SASSYS-1 fast reactor safety analysis code. SHRT-17 was a protected loss of flow test where a loss of electrical power to all sodium coolant pumps was simulated to demonstrate the effectiveness of natural circulation cooling characteristics. SHRT-45R was an unprotected loss of flow test where the control rod scram function of the plant protection system was disabled to demonstrate the effectiveness of EBR-II’s passive reactivity feedbacks. BOP-301 and BOP-302R were unprotected loss of heat sink tests that demonstrated how reactivity feedback effects driven by changes to the core inlet temperature can shut down the fission process. This validation activity leverages modeling and simulation efforts that originated under an International Atomic Energy Agency Coordinated Research Project for benchmark analysis of the EBR-II Shutdown Heat Removal Tests. The SAS4A/SASSYS-1 models originally developed for the CRP have been modernized to utilize new code features and modeling practices. Differences between the predicted and measured test data were explored and the causes of these differences were identified as being due to modeling approximations, uncertainty in transient component behavior, and instrumentation uncertainties. Overall, it was concluded that for SHRT-17, SHRT-45R, BOP-301, and BOP-302R there was good agreement between the flow, power, and temperature predictions and the measured data.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2023

SAS4A/SASSYS-1 Validation with EBR-II Tests Performed During the SHRT Testing Program (Rev. 2)

The EBR-II sodium-cooled fast reactor supported a wide range of fast reactor research activities. The final fifteen years of operations at EBR-II were used for experiments and tests to demonstrate the importance of passive safety in liquid metal reactors and the capability of such systems to provide strong passive responses during off-normal conditions. The Shutdown Heat Removal Test program at EBR-II provided test data supporting the validation of computer codes for design, licensing, and operation of LMRs, among other objectives. The program included nearly sixty tests, most of which were protected and unprotected loss of flow and loss of heat sink tests run at various initial powers and flow rates. This report documents the results of modeling and simulation of tests from the Shutdown Heat Removal Test program to support validation of Argonne’s SAS4A/SASSYS-1 fast reactor safety analysis code. SHRT-17 and SHRT-6 were protected loss of flow tests where a loss of electrical power to all sodium coolant pumps was simulated to demonstrate the effectiveness of natural circulation cooling characteristics. SHRT-45R, SHRT-39, and SHRT-43R were unprotected loss of flow tests where the control rod scram function of the plant protection system was disabled to demonstrate the effectiveness of EBR-II’s passive reactivity feedbacks. BOP-301 and BOP-302R were unprotected loss of heat sink tests that demonstrated how reactivity feedback effects driven by changes to the core inlet temperature can shut down the fission process. PICT-5/6 demonstrated how core power could be increased and decreased via changes in the intermediate sodium and feedwater flow rates. This validation activity leverages modeling and simulation efforts that originated under an International Atomic Energy Agency Coordinated Research Project for benchmark analysis of the EBR-II Shutdown Heat Removal Tests. The SAS4A/SASSYS-1 models originally developed for the CRP have been modernized to utilize new code features and modeling practices. Differences between the predicted and measured test data were explored and the causes of these differences were identified as being due to modeling approximations, uncertainty in transient component behavior, and instrumentation uncertainties. Overall, it was concluded that for all tests simulated there was good agreement between the flow, power, and temperature predictions and the measured data.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2023

A New Proposal Generalized Predictive Control Algorithm With Polynomial Reference Tracking Applied for Sodium Fast Reactors

This paper proposes a generalized predictive control (GPC) with constraints and orthonormal Laguerre functions using the simplified model of the primary system (reactor core and intermediate heat exchanger (IHX)) of a prototypical sodium fast reactor (SFR). This paper develops a multiple-input multiple-output (MIMO) GPC with input constraints able to track polynomial references of any degree applied in coolant temperature difference across the core and fractional power. The manipulated variables of the GPC-SFR are the reactivity and the sodium flow rate of the primary and secondary pipes. Moreover, orthonormal Laguerre functions and step down condition number techniques were also applied to avoid the numerical ill-conditioning issue in quadratic programming of large systems. Thus, a GPC type-2 was designed to control fractional power, coolant temperature difference across the core and sodium tank temperature of the SFR primary system when temperature references change according to a linear ramp after reaching their steady-state operation, sustaining 100% power operation on the reactor. In order to analyze the load tracking capability of the GPC-SFR type-2, the load following from 100% fractional power (FP) to 60% FP at 0.8% FP/min rate is simulated. Constraints on the rate of coolant temperature difference across the core and reactivity were applied for the design safety. For comparison criteria, this paper compares the GPC-SFR type-2 with the GPC-SFR type-1, i.e., standard model predictive control (MPC), to verify the viability and superior performance of the proposal regarding: (a) ramp-tracking capability of temperature and load; (b) the rejections of a reactivity disturbance of -1 cent and a secondary sodium inlet temperature disturbance of +10°F; and (c) a simulation with uncertainty in reactor design. The simulations show that the GPC-SFR type-2 overcome the GPC-SFR type-1 robustness and performance.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2020

Distonic radical anion species in cysteine oxidation processes

Oxidation of cysteine residues constitutes an important regulatory mechanism in the function of biological systems. Much of this behavior is controlled by the specific chemical properties of the thiol side-chain group, where reac-tions with reactive oxygen species take place. Herein, we in-vestigated the entire cysteine oxidation cycle Cys-SH ? Cys-SOnH (n = 1, 2, 3) using cryogenic negative ion photoelectron spectroscopy and quantum-chemical calculations. The conven-tional view on the first reversible oxidation step (n = 1) is as-sociated with sulfinate species. Yet our results indicate that an alternative option exists in the form of novel distonic radical anion •OS-CH2CH(NH2)-COO- with an unpaired electron on the thiol group and excess negative charge on the carboxylate. Higher order oxidation states (n = 2, 3) are thought to be asso-ciated with irreversible oxidative damage, and our results show that excess negative charge in those cases migrates to -SOn- group. Furthermore, these species are stable towards 1e oxidation, as opposed to the n = 1 case that undergoes intra-molecular proton transfer. The molecular level insights report-ed in this work provide direct spectroscopic evidences towards unique chemical versatility of Cys-sulfenic acid (Cys-SOH) in post-translational modifications of protein systems. This research was supported by the U.S. Department of Energy (DOE), Office of Science, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences and Biosciences (X.-B. W. and M. V.) and was performed at the EMSL, a national scientific user facility sponsored by DOE's Office of Biological and Environmental Research and located at the Pacific Northwest National Laboratory. Z. B. Q. acknowledges additional support from the National Natural Science Foundation of China (Grant No. 21873003 and 21503003) and the Special Program for Applied Research on Super Computation of the NSFC-Guangdong Joint Fund (the second phase) (Grant No. U1501501) and Super Computation of Shenzhen.

Qin, Zhengbo↗

DOE OSTI2023

Effect of substrate and growth method on vanadium dioxide thin films by RF magnetron sputtering: Vanadium metal oxidation vs reactive sputtering

Vanadium dioxide (VO 2 ) undergoes a metal–insulator phase transition at ~70 °C and has attracted substantial interest for potential applications in electronics, including those in neuromorphic computing. The vanadium–oxygen system has a rather complicated phase diagram, and controlling the stoichiometry and the phase of thin films of vanadium oxides is a well-known challenge. Here, we explore the novel combination of two methods of VO 2 thin film deposition using off-axis RF magnetron sputtering on (100)- and (111)-oriented yttria-stabilized zirconia (YSZ) substrates: reactive sputtering of vanadium in an oxygen environment and sputtering of vanadium metal followed by oxidation to VO 2 . Interestingly, the reactive sputtering process on both substrate orientations yields the metastable semiconducting VO 2 (B) phase, which is structurally stabilized by the YSZ surface. The metal sputtering and oxidation process on YSZ produces mainly the equilibrium monoclinic (or M1) phase of VO 2 that exhibits a metal–insulator transition. Using this method, we obtained thin films of (010)-textured polycrystalline VO 2 (M1) that show a metal–insulator transition with an on/off ratio larger than 1000.

36 MATERIALS SCIENCE↗