Search NASA⌕ Search

SEARCH · Search NASA

Results for “Reference Model 4”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

SDU 6 Modeling Study to Support Design Development

In response to Technical Task Request (TTR) HLW-SSF-TTR-2012-0017 (1), SRNL performed modeling studies to evaluate alternative design features for the 32 million gallon Saltstone Disposal Unit (SDU) referred to as SDU 6. This initial modeling study was intended to assess the performance of major components of the structure that are most significant to the PA. Information provided by the modeling will support the development of a SDU 6 Preliminary Design Model and Recommendation Report to be written by SRR Closure and Waste Disposal Authority. Key inputs and assumptions for the modeling were provided to SRNL in SRR-SPT-2011-00113 (2). A table reiterates the base case and four sensitivity case studies requested in this reference. In general, as shown in Table 4, when compared to Vault 2 Case A, the Base Case SDU 6 design produced higher peak fluxes to the water table during the 10,000 year period of analysis but lower peak fluxes within a 15,000 to 20,000 time frame. SDU 6 will contain approximately ten times the inventory of a single Vault 2 and the SDU 6 footprint is comparable to that of a group of four Vault 2 disposal units. Therefore, the radionuclide flux from SDU 6 and that from a single Vault 2 are not directly comparable. A more direct comparison would be to compare the maximum dose obtained at the 100 m boundary from the seven SDU's that will replace the 64 FDC's analyzed in the 2009 PA. This analysis will be performed in the next set of calculations planned for SDU design evaluation. Aquifer transport and dose calculations were not intended to be part of this initial scoping study. However, results from this study do indicate that replacement of the FDC design with SDU would not yield significantly higher peak doses. If the thickness of the SDU 6 floor is increased, peak doses would not occur during the 10,000 year period of analysis.

54 ENVIRONMENTAL SCIENCES↗

Toward Improved Land Surface Initialization in Support of Regional WRF Forecasts at the Kenya Meteorological Service (KMS)

Flooding and drought are two key forecasting challenges for the Kenya Meteorological Service (KMS). Atmospheric processes leading to excessive precipitation and/or prolonged drought can be quite sensitive to the state of the land surface, which interacts with the planetary boundary layer (PBL) of the atmosphere providing a source of heat and moisture. The development and evolution of precipitation systems are affected by heat and moisture fluxes from the land surface, particularly within weakly-sheared environments such as in the tropics and sub-tropics. These heat and moisture fluxes during the day can be strongly influenced by land cover, vegetation, and soil moisture content. Therefore, it is important to represent the land surface state as accurately as possible in land surface and numerical weather prediction (NWP) models. Enhanced regional modeling capabilities have the potential to improve forecast guidance in support of daily operations and high-impact weather over eastern Africa. KMS currently runs a configuration of the Weather Research and Forecasting (WRF) NWP model in real time to support its daily forecasting operations, making use of the NOAA/National Weather Service (NWS) Science and Training Resource Center's Environmental Modeling System (EMS) to manage and produce the KMS-WRF runs on a regional grid over eastern Africa. Two organizations at the NASA Marshall Space Flight Center in Huntsville, AL, SERVIR and the Shortterm Prediction Research and Transition (SPoRT) Center, have established a working partnership with KMS for enhancing its regional modeling capabilities through new datasets and tools. To accomplish this goal, SPoRT and SERVIR is providing enhanced, experimental land surface initialization datasets and model verification capabilities to KMS as part of this collaboration. To produce a land-surface initialization more consistent with the resolution of the KMS-WRF runs, the NASA Land Information System (LIS) is run at a comparable resolution to provide real-time, daily soil initialization data in place of data interpolated from the National Centers for Environmental Prediction (NCEP) Global Forecast System (GFS) model soil moisture and temperature fields. Additionally, realtime green vegetation fraction (GVF) data from the Visible Infrared Imaging Radiometer Suite (VIIRS) on the Suomi National Polar-orbiting Partnership (Suomi- NPP) satellite will be incorporated into the KMS-WRF runs, once it becomes publicly available from the National Environmental Satellite Data and Information Service (NESDIS). Finally, model verification capabilities will be transitioned to KMS using the Model Evaluation Tools (MET; Brown et al. 2009) package in conjunction with a dynamic scripting package developed by SPoRT (Zavodsky et al. 2014), to help quantify possible improvements in simulated temperature, moisture and precipitation resulting from the experimental land surface initialization. Furthermore, the transition of these MET tools will enable KMS to monitor model forecast accuracy in near real time. This paper presents preliminary efforts to improve land surface model initialization over eastern Africa in support of operations at KMS. The remainder of this extended abstract is organized as follows: The collaborating organizations involved in the project are described in Section 2; background information on LIS and the configuration for eastern Africa is presented in Section 3; the WRF configuration used in this modeling experiment is described in Section 4; sample experimental WRF output with and without LIS initialization data are given in Section 5; a summary is given in Section 6 followed by acknowledgements and references.

Case, Johnathan L.↗

SU-E-J-148: Tools for Development of 4D Proton CT

Purpose: To develop tools for performing 4D proton computed tomography (CT). Methods: A suitable patient with a tumor in the right lower lobe was selected from a set of 4D CT scans. The volumetric CT images formed the basis for calculating the parameters of a breathing model that allows reconstruction of a static reference CT and CT images in each breathing phase. The images were imported into the TOPAS Monte Carlo simulation platform for simulating an experimental proton CT scan with 45 projections spaced by 4 degree intervals. Each projection acquired data for 2 seconds followed by a gantry rotation for 2 seconds without acquisition. The scan covered 180 degrees with individual protons passing through a 9-cm slab of the patient’s lung covering the moving tumor. An initial proton energy sufficient for penetrating the patient from all directions was determined. Performing the proton CT simulation, TOPAS provided output of the proton energy and coordinates registered in two planes before and after the patient, respectively. The set of projection data was then used with an iterative reconstruction algorithm to generate a volumetric proton CT image set of the static reference image and the image obtained under breathing motion, respectively. Results: An initial proton energy of 230 MeV was found to be sufficient, while for an initial energy of 200 MeV a substantial number of protons did not penetrate the patient. The reconstruction of the static reference image set provided sufficient detail for treatment planning. Conclusion: We have developed tools to perform studies of proton CT in the presence of lung motion based on the TOPAS simulation toolkit. This will allow to optimize 4D reconstruction algorithms by synchronizing the acquired proton CT data with a breathing signal and utilizing a breathing model obtained prior to the proton CT scan. This research has been supported by the National Institute Of Biomedical Imaging And Bioengineering of the National Institutes of Health under Award Number R01EB013118.

60 APPLIED LIFE SCIENCES↗

Microphysics, Radiation and Surface Processes in the Goddard Cumulus Ensemble (GCE) Model

One of the most promising methods to test the representation of cloud processes used in climate models is to use observations together with Cloud Resolving Models (CRMs). The CRMs use more sophisticated and realistic representations of cloud microphysical processes, and they can reasonably well resolve the time evolution, structure, and life cycles of clouds and cloud systems (size about 2-200 km). The CRMs also allow explicit interaction between out-going longwave (cooling) and in-coming solar (heating) radiation with clouds. Observations can provide the initial conditions and validation for CRM results. The Goddard Cumulus Ensemble (GCE) Model, a CRM, has been developed and improved at NASA/Goddard Space Flight Center over the past two decades. The GCE model has been used to understand the following: 1) water and energy cycles and their roles in the tropical climate system; 2) the vertical redistribution of ozone and trace constituents by individual clouds and well organized convective systems over various spatial scales; 3) the relationship between the vertical distribution of latent heating (phase change of water) and the large-scale (pre-storm) environment; 4) the validity of assumptions used in the representation of cloud processes in climate and global circulation models; and 5) the representation of cloud microphysical processes and their interaction with radiative forcing over tropical and midlatitude regions. Four-dimensional cloud and latent heating fields simulated from the GCE model have been provided to the TRMM Science Data and Information System (TSDIS) to develop and improve algorithms for retrieving rainfall and latent heating rates for TRMM and the NASA Earth Observing System (EOS). More than 90 referred papers using the GCE model have been published in the last two decades. Also, more than 10 national and international universities are currently using the GCE model for research and teaching. In this talk, five specific major GCE improvements: (1) ice microphysics, (2) longwave and shortwave radiative transfer processes, (3) land surface processes, (4) ocean surface fluxes and (5) ocean mixed layer processes are presented. The performance of these new GCE improvements will be examined. Observations are used for model validation.

Tao, Wei-Kuo↗

Dielectric relaxations and alternating current conductivity in manganese substituted cobalt ferrite

Manganese (Mn) substituted cobalt ferrites (CoFe{sub 2-x}Mn{sub x}O{sub 4}, referred to CFMO) have been synthesized by the solid state reaction method and their dielectric properties and ac conductivity have been evaluated as a function of applied frequency and temperature. X-ray diffraction measurements indicate that CFMO crystallize in the inverse cubic spinel phase with a lattice constant ∼8.38 Å. Frequency dependent dielectric measurements at room temperature obey the modified Debye model with relaxation time of 10{sup −4} s and spreading factor of 0.35(±0.05). The frequency (20 Hz–1 MHz) and temperature (T = 300–900 K) dependent dielectric constant analyses indicate that CFMO exhibit two dielectric relaxations at lower frequencies (1–10 kHz), while completely single dielectric relaxation for higher frequencies (100 kHz–1 MHz). The dielectric constant of CFMO is T-independent up to ∼400 K, at which point increasing trend prevails. The dielectric constant increase with T > 400 K is explained through impedance spectroscopy assuming a two-layer model, where low-resistive grains separated from each other by high-resistive grain boundaries. Following this model, the two electrical responses in impedance formalism are attributed to the grain and grain-boundary effects, respectively, which also satisfactorily accounts for the two dielectric relaxations. The capacitance of the bulk of the grain determined from impedance analyses is ∼10 pF, which remains constant with T, while the grain-boundary capacitance increases up to ∼3.5 nF with increasing T. The tan δ (loss tangent)-T also reveals the typical behavior of relaxation losses in CFMO.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Detection of a MoSe{sub 2} secondary phase layer in CZTSe by spectroscopic ellipsometry

We demonstrate the application of Spectroscopic Ellipsometry (SE) for identification of secondary phase MoSe{sub 2} in polycrystalline Cu{sub 2}ZnSnSe{sub 4} (CZTSe) samples. A MoSe{sub 2} reference sample was analyzed, and its optical constants (ε{sub 1} and ε{sub 2}) were extracted by SE analysis. This dataset was implemented into an optical model for analyzing SE data from a glass/Mo/CZTSe sample containing MoSe{sub 2} at the back side of the absorber. We present results on the n and k values of CZTSe and show the extraction of the thickness of the secondary phase MoSe{sub 2} layer. Raman spectroscopy and scanning electron microscopy were applied to confirm the SE results.

36 MATERIALS SCIENCE↗

Hubbard-corrected oxide formation enthalpies without adjustable parameters

A density functional theory (DFT) approach to computing transition metal oxide heat of formation without adjustable parameters is presented. Different degrees of d-electron localization in oxides are treated within the DFT+U approach with site-dependent, first-principles Hubbard U-parameters obtained from linear response theory, and delocalized states in the metallic phases are treated without Hubbard corrections. Comparison of relative stabilities of these differently treated phases is enabled by a local d-electron density matrix-dependent model, which was found by genetic programming against experimental reference formation enthalpies. This mathematically simple model does not explicitly depend on the Hubbard-corrected ionic species and is shown to reproduce the heats of formation of the Mott insulators Ca 2 RuO 4 and Y 2 Ru 2 O 7 within ~3% of experimental results, where the experimental training data did not contain Ru oxides. This newly developed method thus absolves from the need for element-specific corrections fitted to experiments in existing Hubbard-corrected approaches to the prediction of reaction energies of transition metal oxides and metals. The absence of fitting parameters opens up here the possibility to predict relative thermodynamic stabilities and reaction energies involving d-states of varying degree of localization at transition metal oxide interfaces and defects, where site-dependent U-parameters will be particularly important and devising a fitting scheme against experimental data with predictive power would be exceedingly difficult.

transition metal oxides↗

Flavor symmetry breaking and vacuum alignment on orbifolds

Flavor symmetry has been widely studied for figuring out the masses and mixing angles of standard model fermions. In this paper we present a framework for handling flavor symmetry breaking where the symmetry breaking is triggered by boundary conditions of scalar fields in extra-dimensional space. The alignment of scalar expectation values is achieved without referring to any details of scalar potential and its minimization procedure. As applications to non-Abelian discrete flavor symmetries, illustrative lepton mass models are constructed where the S{sub 3} and A{sub 4} flavor symmetries are broken down to the directions leading to the tribimaximal form of lepton mixing and realistic mass patterns.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Complete Genome Sequence of Phormidium yuhuli AB48, Isolated from an Industrial Photobioreactor Environment

We report the genome of Phormidium yuhuli AB48, which includes a circular chromosome and a circular plasmid (4,747,469 bp and 51,599 bp, respectively). This is currently the only closed reference genome of an isolate of the Phormidium genus, based on the Genome Taxonomy Database (GTDB), providing a potential model system for sustainable biotechnology innovation.

59 BASIC BIOLOGICAL SCIENCES↗

Model Structural Inference Using Local Dynamic Operators

This paper focuses on the problem of quantifying the effects of model-structure uncertainty in the context of time-evolving dynamical systems. This is motivated by multi-model uncertainty in computer physics simulations: developers often make different modeling choices in numerical approximations and process simplifications, leading to different numerical codes that ostensibly represent the same underlying dynamics. We consider model-structure inference as a two-step methodology: the first step is to perform system identification on numerical codes for which it is possible to observe the full state; the second step is structural uncertainty quantification, in which the goal is to search candidate models "close" to the numerical code surrogates for those that best match a quantity of interest (QOI) from some empirical data sets. Here, we (1) define a discrete, local representation of the structure of a partial differential equation, which we refer to as the "local dynamical operator" (LDO); (2) identify model structure nonintrusively from numerical code output; (3) nonintrusively construct a reduced-order model (ROM) of the numerical model through POD-DEIM-Galerkin projection; (4) perturb the ROM dynamics to approximate the behavior of alternate model structures; and (5) apply Bayesian inference and energy conservation laws to calibrate a LDO to a given QOI. We demonstrate these techniques using the two-dimensional rotating shallow water equations as an example system.

97 MATHEMATICS AND COMPUTING↗

CORPSE model with litter decomposition parameters derived from the LIDET dataset

This is a version of the CORPSE model (Carbon, Organisms, Rhizosphere and Protection in the Soil Environment, Sulman et al. 2014) that uses litter decomposition parameters derived from a modified Monte Carlo simulation using the LIDET litter decomposition dataset (Long-term Intersite Decomposition Experiment Team, Harmon 2013). The code also includes the Baseline parameters, and the eight other best parameter sets identified in a modified Monte Carlo simulation. Related publication:Juice, S.M., Ridgeway, J.R., Hartman, M.D., Parton, W.J., Berardi, D.M., Sulman, B.N., Allen, K.E., & Brzostek, E.R. Reparameterizing litter decomposition using a simplified Monte Carlo method improves litter decay simulated by a microbial model and alters bioenergy soil carbon estimates. Description of files:The folder "Input Files" contains one folder for each LIDET site with data necessary to run the model. Note that "(site)" in the filenames below indicates where the LIDET site code appears (see Table 1 for site codes). Data streams include: CORPSE_full_spinup_litter.csv, CORPSE_full_spinup_rhizo.csv, CORPSE_full_spinup_bulk.csv, litterbag_init_100g_6spp.csv: initial C and N (kg C or N/m2) pool values for each soil layer, the litterbag_init_100_6spp.csv file is for the litterbag layer and is the same file for all sites. All initial C and N files have the same columns (Column - Description - Units) uFastC - Unprotected fast decomposing carbon - kg carbon/m2 uSlowC - Unprotected slow decomposing carbon - kg carbon/m2 uNecroC - Unprotected necromass carbon - kg carbon/m2 pFastC - Protected fast decomposing carbon - kg carbon/m2 pSlowC - Protected slow decomposing carbon - kg carbon/m2 pNecroC - Protected necromass carbon - kg carbon/m2 livingMicrobeC - Carbon in living microbial biomass - kg carbon/m2 uFastN - Unprotected fast decomposing nitrogen - kg nitrogen/m2 uSlowN - Unprotected slow decomposing nitrogen - kg nitrogen/m2 uNecroN - Unprotected necromass nitrogen - kg nitrogen/m2 pFastN - Protected fast decomposing nitrogen - kg nitrogen/m2 pSlowN - Protected slow decomposing nitrogen - kg nitrogen/m2 pNecroN - Protected necromass nitrogen - kg nitrogen/m2 inorganicN - Inorganic nitrogen - kg nitrogen/m2 CO2 - Carbon in carbon dioxide - kg carbon/m2 livingMicrobeN - Nitrogen in living microbial biomass - kg nitrogen/m2 soilT (site) DOY274start.csv: Average daily soil temperature (oC) interpolated from previously calculated monthly values used in DayCent LIDET simulations (Bonan et al., 2013). soilT (site) DOY274start.csv: Average daily soil volumetric water content (VWC) scalar interpolated from previously calculated monthly values used in DayCent LIDET simulations (Bonan et al., 2013). litter production.csv: Average daily litter production values for each site, data sources listed in Table S3 of related publication. litter (site) CN.csv: C:N ratio for each species from LIDET dataset (Table 2, Harmon 2013). (site).csv: Table indicating number of observations for each species decomposed at each site. Instructions: Save the model code ("CORPSE_LIDET.R") and "Input Files" folder in the same folder. Also make a folder for the model output (e.g., "results_Baseline") in the same folder. Set the working directory (setwd) in the model code to the folder with the files saved in step #1. Select the parameter set to use for the litter and litterbag compartments, comment out all other parameter sets. Run code. Output will be saved in the folder made in step 1. Output destination can be changed as necessary in code section called "Running the model." Table 1 LIDET sites and site codes used in model files. Site Code - Site AND - H.J. Andrews Experimental Forest BNZ - Bonanza Creek Experimental Forest BSF - Blodgett Research Forest CDR - Cedar Creek Natural History Area CPR - Central Plains Experimental Range HBR - Hubbard Brook Experimental Forest HFR - Harvard Forest JUN - Juneau KBS - Kellogg Biological Station KNZ - Konza Prairie Research Natural Area NWT - Niwot Ridge/Green Lakes Valley OLY - Olympic National Park OLY Conifer forest SEV - Sevilleta National Wildlife Refuge SMR - Santa Margarita Ecological Reserve UFL - University of Florida VCR - Virginia Coast Reserve Table 2 LIDET species and species codes used in model files (6 common species). Species - Species Code Sugar maple (Acer saccharum) - ACSA Drypetes (Drypetes glauca) - DRGL Red pine (Pinus resinosa) - PIRE Chestnut oak (Quercus prinus) - QUPR Western redcedar (Thuja plicata) - THPL Wheat (Triticum aestivum) - TRAE References:Bonan, G. B., Hartman, M. D., Parton, W. J., & Wieder, W. R. (2013). Evaluating litter decomposition in earth system models with long-term litterbag experiments: an example using the Community Land Model version 4 (CLM4). Global Change Biology, 19(3), 957-974. https://doi.org/https://doi.org/10.1111/gcb.12031 Harmon, M. (2013). LTER Intersite Fine Litter Decomposition Experiment (LIDET), 1990 to 2002. Long-Term Ecological Research. Forest Science Data Bank, Corvallis, OR. [Data set]. Accessed http://andlter.forestry.oregonstate.edu/data/abstract.aspx?dbcode=TD023. https://doi.org/10.6073/pasta/f35f56bea52d78b6a1ecf1952b4889c5. Sulman, B. N., Phillips, R. P., Oishi, A. C., Shevliakova, E., & Pacala, S. W. (2014). Microbe-driven turnover offsets mineral-mediated storage of soil carbon under elevated CO2. Nature Climate Change, 4, 1099 - 1102. https://doi.org/10.1038/nclimate2436

Juice, Stephanie↗

Completion design improvement using a deep convolutional network

Maximizing stimulated natural and hydraulic fracture network is one of the primary hydraulic fracturing concerns for economic production from a horizontal shale gas well. Geomechanical facies and preexisting fractures in each stage are identified based on similarities in formation characteristics to optimize the locations of perforation clusters. This often requires analyzing large volumes of drilling, Logging While Drilling (LWD) and Measurement While Drilling (MWD) data. In this paper, we develop a methodology that calculates the mechanical specific energy (MSE) using real-time drill string acceleration signals directly from its definition. High resolution vibration signals have been collected using a tri-axial accerlometer, which was an auxiliary tool included in acoustic borehole imager. This technique provides a cost-efficient solution for engineered completion design. Furthermore, we adopt deep Convolutional Neural Network (CNN) with signal processing to build a data pipeline that effectively extracts patterns from dynamic acceleration signals for rock lateral MSE classification. First, we apply discrete wavelet transform and Short-Time Fourier Transform (STFT) for signal denoising and pattern recognition. Then we construct an image dataset using multi-scale image fusion at pixel level from 3 sensor channels, including axial, lateral acceleration spectrograms and zero-padded revolutions per minute (RPM). The resulted RGB image dataset includes 4,000 images of 5 MSE ranges with various rock strength conditions. Our results demonstrate that the proposed deep learning model can achieve more than 90% classification accuracy. The deep learning results, as a reference source, were applied in selected Marcellus Shale Energy and Environmental Lab (MSEEL) wells engineered completion located in the Marcellus shale gas site.

03 NATURAL GAS↗

SU-C-BRA-07: Variability of Patient-Specific Motion Models Derived Using Different Deformable Image Registration Algorithms for Lung Cancer Stereotactic Body Radiotherapy (SBRT) Patients

Purpose: To study the variability of patient-specific motion models derived from 4-dimensional CT (4DCT) images using different deformable image registration (DIR) algorithms for lung cancer stereotactic body radiotherapy (SBRT) patients. Methods: Motion models are derived by 1) applying DIR between each 4DCT image and a reference image, resulting in a set of displacement vector fields (DVFs), and 2) performing principal component analysis (PCA) on the DVFs, resulting in a motion model (a set of eigenvectors capturing the variations in the DVFs). Three DIR algorithms were used: 1) Demons, 2) Horn-Schunck, and 3) iterative optical flow. The motion models derived were compared using patient 4DCT scans. Results: Motion models were derived and the variations were evaluated according to three criteria: 1) the average root mean square (RMS) difference which measures the absolute difference between the components of the eigenvectors, 2) the dot product between the eigenvectors which measures the angular difference between the eigenvectors in space, and 3) the Euclidean Model Norm (EMN), which is calculated by summing the dot products of an eigenvector with the first three eigenvectors from the reference motion model in quadrature. EMN measures how well an eigenvector can be reconstructed using another motion model derived using a different DIR algorithm. Results showed that comparing to a reference motion model (derived using the Demons algorithm), the eigenvectors of the motion model derived using the iterative optical flow algorithm has smaller RMS, larger dot product, and larger EMN values than those of the motion model derived using Horn-Schunck algorithm. Conclusion: The study showed that motion models vary depending on which DIR algorithms were used to derive them. The choice of a DIR algorithm may affect the accuracy of the resulting model, and it is important to assess the suitability of the algorithm chosen for a particular application. This project was supported, in part, through a Master Research Agreement with Varian Medical Systems, Inc, Palo Alto, CA.

60 APPLIED LIFE SCIENCES↗

Final report of LLNS subcontract No. B646608

This report refers to Subcontract No. B646608 from Lawrence Livermore National Security to UC Irvine. The vision of this subcontract is to implement new, necessary scientific modeling capabilities within the E3SM code repository for versions 2 through 4.

54 ENVIRONMENTAL SCIENCES↗

KINEMATICS OF M51-TYPE INTERACTING GALAXIES

We present a kinematic catalog for 21 M51-type galaxies. It consists of radial velocity distributions observed with long-slit spectroscopy along different position angles, for both the main and satellite components. We detect deviations from circular motion in most of the main galaxies of each pair, due to the gravitational perturbation produced by the satellite galaxy. However, some systems do not show significant distortions in their radial velocity curves. We found some differences between the directions of the photometric and kinematic major axes in the main galaxies with a bar subsystem. The Tully–Fisher relation in the B -band and Ks -band for the present sample of M51-type systems is flatter than in isolated galaxies. Using the radial velocity data set, we built a synthetic normalized radial velocity distribution, as a reference for future modeling of these peculiar systems. The synthetic rotation curve, representing the typical rotation curve of the main galaxy in an M51-type pair, is near to solid body-like inside 4 kpc, and then is nearly flat within the radial range 5–15 kpc. The relative position angles between the major axis of the main galaxy and the companion’s location, as well as the amplitude of the velocity difference, indicate that the orbital motion of the satellite has a large projection on the equatorial plane of the main galaxy. In addition, the differences in radial velocity between the two galaxies indicate that the satellite’s orbital motion is within the range of amplitudes of the rotation curve of the main galaxy, and all the M51-type systems studied here, except for one, are gravitationally bound.

79 ASTRONOMY AND ASTROPHYSICS↗

Measurement of regional compliance using 4DCT images for assessment of radiation treatment

Purpose: Radiation-induced damage, such as inflammation and fibrosis, can compromise ventilation capability of local functional units (alveoli) of the lung. Ventilation function as measured with ventilation images, however, is often complicated by the underlying mechanical variations. The purpose of this study is to present a 4DCT-based method to measure the regional ventilation capability, namely, regional compliance, for the evaluation of radiation-induced lung damage. Methods: Six 4DCT images were investigated in this study: One previously used in the generation of a POPI model and the other five acquired at Henry Ford Health System. A tetrahedral geometrical model was created and scaled to encompass each of the 4DCT image domains. Image registrations were performed on each of the 4DCT images using a multiresolution Demons algorithm. The images at the end of exhalation were selected as a reference. Images at other exhalation phases were registered to the reference phase. For the POPI-modeled patient, each of these registration instances was validated using 40 landmarks. The displacement vector fields (DVFs) were used first to calculate the volumetric variation of each tetrahedron, which represents the change in the air volume. The calculated results were interpolated to generate 3D ventilation images. With the computed DVF, a finite element method (FEM) framework was developed to compute the stress images of the lung tissue. The regional compliance was then defined as the ratio of the ventilation and stress values and was calculated for each phase. Based on iterative FEM simulations, the potential range of the mechanical parameters for the lung was determined by comparing the model-computed average stress to the clinical reference value of airway pressure. The effect of the parameter variations on the computed stress distributions was estimated using Pearson correlation coefficients. Results: For the POPI-modeled patient, five exhalation phases from the start to the end of exhalation were denoted by P{sub i}, i=1,...,5, respectively. The average lung volume variation relative to the reference phase (P{sub 5}) was reduced from 18% at P{sub 1} to 4.8% at P{sub 4}. The average stress at phase P{sub i} was 1.42, 1.34, 0.74, and 0.28 kPa, and the average regional compliance was 0.19, 0.20, 0.20, and 0.24 for i=1,...,4, respectively. For the other five patients, their average R{sub v} value at the end-inhalation phase was 21.1%, 19.6%, 22.4%, 22.5%, and 18.8%, respectively, and the regional compliance averaged over all six patients is 0.2. For elasticity parameters chosen from the potential parameter range, the resultant stress distributions were found to be similar to each other with Pearson correlation coefficients greater than 0.81. Conclusions: A 4DCT-based mechanical model has been developed to calculate the ventilation and stress images of the lung. The resultant regional compliance represents the lung's elasticity property and is potentially useful in correlating regions of lung damage with radiation dose following a course of radiation therapy.

60 APPLIED LIFE SCIENCES↗

TH-CD-207A-11: Sensitivity Analysis of Action Limits for Real-Time EPID-Based Delivery Verification System Using Artificial Clinical Relevant Error Simulations

Purpose: A real-time patient treatment delivery verification system using EPID (Watchdog) has been developed as an advanced patient safety tool. In a pilot study data was acquired for 119 prostate and head and neck (HN) IMRT patient deliveries to generate body-site specific action limits using statistical process control. The purpose of this study is to determine the sensitivity of Watchdog to detect clinically significant errors during treatment delivery. Methods: Watchdog utilizes a physics-based model to generate a series of predicted transit cine EPID images as a reference data set, and compares these in real-time to measured transit cine-EPID images acquired during treatment using chi comparison (4%, 4mm criteria) after the initial 2s of treatment to allow for dose ramp-up. Four study cases were used; dosimetric (monitor unit) errors in prostate (7 fields) and HN (9 fields) IMRT treatments of (5%, 7%, 10%) and positioning (systematic displacement) errors in the same treatments of (5mm, 7mm, 10mm). These errors were introduced by modifying the patient CT scan and re-calculating the predicted EPID data set. The error embedded predicted EPID data sets were compared to the measured EPID data acquired during patient treatment. The treatment delivery percentage (measured from 2s) where Watchdog detected the error was determined. Results: Watchdog detected all simulated errors for all fields during delivery. The dosimetric errors were detected at average treatment delivery percentage of (4%, 0%, 0%) and (7%, 0%, 0%) for prostate and HN respectively. For patient positional errors, the average treatment delivery percentage was (52%, 43%, 25%) and (39%, 16%, 6%). Conclusion: These results suggest that Watchdog can detect significant dosimetric and positioning errors in prostate and HN IMRT treatments in real-time allowing for treatment interruption. Displacements of the patient require longer to detect however incorrect body site or very large geographic misses will be detected rapidly.

60 APPLIED LIFE SCIENCES↗

Product consistency test results for the LAW Phase 4 gases

In this report, the Savannah River National Laboratory provides chemical analysis of Product Consistency Test (PCT) leachates from a series of simulated nuclear waste glasses fabricated at the Pacific Northwest National Laboratory (PNNL). The series included quenched and canister-centerline cooled (CCC) versions of the glasses. The resulting data will be used in the development of enhanced property/composition models for waste vitrification at Hanford. For some of the glass leachates, minor scatter among the triplicate values of some analytes were observed. For other leachates, there were more significant differences among the triplicate values. A review of the PCT data noted that there was little difference between the normalized values based on targeted or measured glass composition. Several of the study glasses have normalized concentration of element “i” (NCi) values that are greater than the Hanford Tank Waste Treatment and Immobilization Plant immobilized low-activity waste constraint of 4 g/L for boron (B), sodium (Na), and silicon (Si). The results of these glasses will help ensure the ability of advanced glass performance models to appropriately predict acceptable compositions. For the study glasses with NCi values exceeding 4 g/L, the CCC heat treatment samples had generally lower NCi values than quenched samples. The samples of the Environmental Assessment (EA) reference glass included with each PCT set had generally consistent NCi values. The release rates for boron (B), potassium (K), lithium (Li), sodium (Na), and silicon (Si) were highly correlated for the study glasses.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗