Search NASA⌕ Search

SEARCH · Search NASA

Results for “SEAPLANES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

The effect of trim angle on the take-off performance

Data obtained at the N.A.C.A. tank from tests on the models of three flying-boat hulls - N.A.C.A. models 11-A, 16, and 22 - are used to demonstrate the effect of trim angle on water resistance. A specific example is taken, and data from Model 11-A are used to show that the trim angle giving the minimum water resistance will give minimum total air-plus-water resistance. Total-resistance curves for best trimmed angles and other angles are compared for the same example. The effect of wind on best trim angles and upon the take-off and run is shown by the working of an example. The possibility of using tank data on trim angles as aid in piloting is discussed, and an instrument for use in determining the trim angle of seaplanes is described. The importance of maintaining the best trim angle throughout the take-off is indicated.

Shoemaker, James M↗

The Increase in Frictional Resistance Caused by Various Types of Rivet Heads as Determined by Tests of Planing Surfaces

The increase in the frictional resistance of a surface caused by the presence of rivet heads was determined by towing four planing surfaces of the same dimensions. One surface was smooth and represented a surface without rivet heads or one with perfectly flush countersunk rivets. The other three surfaces were each fitted with the same number of full-size rivet heads but of a different type arranged in the same pattern on each surface. The surfaces were towed at speeds representative of the high water speeds encountered by seaplanes during take-off and the range of Reynolds Number covered by the test was from 4 x 10(exp 6) to 18 x 10(exp 6). The rivet heads investigated were oval countersunk, brazier, and round for rivets having shanks 5/32 inch in diameter. The oval countersunk heads were sunk below the surface by dimpling the plating around them. The results of the tests showed that, for the rivet heads investigated, the increase in the friction coefficient of the surface is directly proportional to the height of the rivet head. The order of merit in regard to low resistance is flush countersunk, oval countersunk (whether sunk below the surface or not), brazier, and round.

Truscott, Starr↗

The Aerodynamic Drag of Five Models of Side Floats N.A.C.A. Models 51-E, 51-F, 51-G, 51-H, 51-J

The drag of five models of side floats was measured in the N.A.C.A. 7- by 10-foot wind tunnel. The most promising method of reducing the drag of floats indicated by these tests is lowering the angle at which the floats are rigged. The addition of a step to a float does not always increase the drag in the flying range, floats with steps sometimes having lower drag than similar floats without steps. Making the bow chine no higher than necessary might result in a reduction in air drag because of the lower angle of pitch of the chines. Since side floats are used formally to obtain lateral stability when the seaplane is operating on the water at slow speeds or at rest, greater consideration can be given to factors affecting aerodynamic drag than is possible for other types of floats and hulls.

House, R O↗

Estimation of Hydrodynamic Impact Loads and Pressure Distributions on Bodies Approximating Elliptical Cylinders with Special Reference to Water Landings of Helicopters

An approximate method for computing water loads and pressure distributions on lightly loaded elliptical cylinders during oblique water impacts is presented. The method is of special interest for the case of emergency water landings of helicopters. This method makes use of theory developed and checked for landing impacts of seaplanes having bottom cross sections of V and scalloped contours. An illustrative example is given to show typical results obtained from the use of the proposed method of computation. The accuracy of the approximate method was evaluated through comparison with limited experimental data for two-dimensional drops of a rigid circular cylinder at a trim of 0 degrees and a flight -path angle of 90 degrees. The applicability of the proposed formulas to the design of rigid hulls is indicated by the rough agreement obtained between the computed and experimental results. A detailed computational procedure is included as an appendix.

Schnitzer, Emanuel↗

On the stability of oscillations of an airplane wing

During a flight with a Van Berkel W. B. seaplane it was observed that the wing could perform violent oscillations. A theoretical and experimental investigation led to the conclusion, that in some cases an unstable oscillation of the wing-aileron system under the influence of the elastic and aerodynamic forces is possible without further external causes.

FLUTTER - WINGS - VAN BERKEL W B↗

The "navigraph"

Commander Le Prieur, whose flight experience in a low-speed seaplane we related in our number of September 27, 1924, invented, four years ago, an instrument destined to render very great service to aviators, namely, the "navigraph", designed to correct errors of orientation due to the effect of the winds during flight.

COURSE FINDING INSTRUMENTS↗

The Avro "Avian" Airplane : 65 HP. Armstrong-Siddeley "Genet" engine

The Avro Avian, designed by Mr. Chadwick of A.V. Roe & Co., Ltd. has a very low structural weight (estimated at 750 lbs. empty) but with sufficient structural integrity to be eligible of an "Aerobatics" certificate from the British Air Ministry. It can be configured as a monoplane, or a biplane with seaplane floats. It is designed for economical production.

AIRPLANES-AVRO AVIAN (BRIT )↗

Take-off of heavily loaded airplanes

In the present article, several suggestions will be made for shortening the otherwise long take-off distance. For the numerical verification of the process, I will use a graphic method for determining the take-off distance of seaplanes.

LOADS, TAKE-OFF↗

Water Pressure Distribution on a Flying Boat Hull

This is the third in a series of investigations of the water pressures on seaplane floats and hulls, and completes the present program. It consisted of determining the water pressures and accelerations on a Curtiss H-16 flying boat during landing and taxiing maneuvers in smooth and rough water.

Thompson, F L↗

Tank Tests of NACA Model 40 Series of Hulls for Small Flying Boats and Amphibians

The NACA model 40 series of flying-boat hull models consists of 2 forebodies and 3 afterbodies combined to provide several forms suitable for use in small marine aircraft. One forebody is the usual form with hollow bow sections and the other has a bottom surface that is completely developable from bow to step. The afterbodies include a short pointed afterbody with an extension for the tail surfaces, a long afterbody similar to that of a seaplane float but long enough to carry the tail surfaces, and a third obtained by fitting a second step in the latter afterbody. The various combinations were tested in the NACA Tank by the general method over a suitable range of loadings. Fixed-trim tests were made for all speeds likely to be used and free-to-trim tests were made at low speeds to slightly beyond the hump speed. The characteristics of the hulls at best trim angles have been deduced from the data of the tests at fixed trim angles and are given in the form of nondimensional coefficients applicable to any size hull.

Parkinson, John B↗

Measurements in Flight of the Lateral-Control Characteristics of an Airplane Equipped with Full-Span Zap Flaps and Simple Circular-Arc-Type Ailerons

Flight tests were conducted on the OS2U-2 seaplane with simple circular-arc-type ailerons directly connected to the actuating torque tube. Two aileron test installations were made, differing only in the inclination of the projecting surface with the wing's upper surface. The lateral-control characteristics of the airplane were determined from data obtained in stalls and rudder-fixed aileron rolls. The revised ailerons were deficient in maximum rolling effectiveness, but were capable of controlling the rolling tendencies of the airplane near the stall.

AILERON CONTROLS - VOUGHT OS2U-2↗

An Investigation of Hydrofoils in the NACA Tank I : Effect of Dihedral and Depth of Submersion

Tests were conducted on hydrofoil assemblies approximating an arrangement for use under seaplanes or surface boats. A series of hydrofoils, each supported by two struts, was towed at various depths ranging from partial submersions to a depth of 5-chord lengths. At depths greater than 4 or 5 chords, the influence of the surface of the water is small; hydrofoils operating at low speed will have characteristics similar to those of airfoils of the same section.

HYDROFOILS - NACA - CHARACTERISTICS TANK TESTS (NA↗

Experiments with planing surfaces

Experiments with planing surfaces are fundamental, hydrodynamic researches for the purpose of obtaining the most favorable forms for planing boats, flying boats, and seaplane floats, with respect to water resistance and seaworthiness.

Sottorf, W↗

The future of very large subsonic transports

The Very Large Subsonic Transport (VLST) is a multi-use commercial passenger, commercial cargo, and military airlifter roughly 50% larger than the current Lockheed C-5 and Boeing 747. Due to the large size and cost of the VLST, it is unlikely that the commercial market can support more than one aircraft production line, while declining defense budgets will not support a dedicated military VLST. A successful VLST must therefore meet airline requirements for more passenger and cargo capacity on congested routes into slot-limited airports and also provide a cost effective heavy airlift capacity to support the overseas deployment of US military forces. A successful VLST must satisfy three key missions: commercial passenger service with nominal seating capacity at a minimum of 650 passengers with a range capability of 7,000 to 10,000 miles; commercial air cargo service for containerized cargo to support global manufacturing of high value added products, 'just-in-time' parts delivery, and the general globalization of trade; and military airlift with adequate capacity to load current weapon systems, with minimal break-down, over global ranges (7,000 to 10,000 miles) required to reach the operational theater without need of overseas bases and midair refueling. The development of the VLST poses some technical issues specific to large aircraft, but also key technologies applicable to a wide range of subsonic transport aircraft. Key issues and technologies unique to the VLST include: large composite structures; dynamic control of a large, flexible structure; aircraft noise requirements for aircraft over 850,000 pounds; and increased aircraft separation due to increased wake vortex generation. Other issues, while not unique to the VLST, will critically impact the ability to build an efficient and affordable aircraft include: active control systems: Fly-By-Light/Power-By-Wire (FBL/PBW); high lift systems; flight deck associate systems; laminar flow; emergency egress; and modular design. The VLST will encounter severe restrictions on weight, ground flotation, span, length, and door height to operate at current airports/bases, gates, and cargo loading systems. One option under consideration is for a sea-based VLST, either a conventional seaplane or Wing-In-Ground effect (WIG) vehicle, which would allow greater operational flexibility, while introducing other design challenges such as water impact loads and salt-water corrosion. Lockheed Martin is currently developing a floatplane version of the C-130 Hercules which will provide experience with a modern sea-based aircraft. In addition to its own ongoing research activities, Lockheed Martin is also participating in the NASA Advanced Subsonic Technology, High Speed Research (HSR), and other programs which address some of the technologies needed for the VLST. The VLST will require NASA and US aerospace companies to work together to develop new capabilities and technologies for make the VLST a viable part of transportation beyond 2000.

Justice, R. Steven↗

Planing of Watercraft

The present report deals with the processes accompanying the planing of a planing boat or a seaplane on water . The study is largely based upon theoretical investigations; mathematical problems and proofs are not discussed. To analyze theoreticaly actual planing processes, giving due consideration to all aspects of the problem, is probably not possible. The theories therefore treat various simple limiting cases, which in their entirety give a picture of the planing processes and enable the interpretation of the experimental results. The discussion is concerned with the stationary planing attitude: the boat planes at a constant speed V on an originally smooth surface.

Wagner, Herbert↗

Hydrodynamic Characteristics of an Aerodynamically Refined Planing-Tail Hull

The hydrodynamic characteristics of an aerodynamically refined planing-tail hull were determined from dynamic model tests in Langley tank no. 2. Stable take-off could be made for a wide range of locations of the center of gravity. The lower porpoising limit peak was high, but no upper limit was encountered. Resistance was high, being about the same as that of float seaplanes. A reasonable range of trims for stable landings was available only in the aft range of center-of-gravity locations.

McKann, Robert↗

Preliminary Tests in the NACA Tank to Investigate the Fundamental Characteristics of Hydrofoils

This preliminary investigation was made to study the hydrodynamic properties and general behavior of simple hydrofoils. Six 5- by 30-inch plain, rectangular hydrofoils were tested in the NACA tank at various speeds, angles of attack and depths below the water surface. Two of the hydrofoils had sections representing the sections of commonly used airfoils, one had a section similar to one developed Guidoni for use with hydrofoil-equipped seaplane floats, and three had sections designed to have constant chordwise pressure distributions at given values of the lift coefficient for the purpose of delaying the speed at which cavitation begins. The experimental results are presented as curves of the lift and drag coefficients plotted against speed for the various angles of attack and depths for which the hydrofoils were tested. A number of derived curves are included for the purpose of better comparing the characteristics of the hydrofoils and to show the effects of depth. Several representative photographs show the development of cavitation on the the upper surface of the hydrofoils. The results indicate that properly designed hydrofoil sections will have excellent characteristics and that the speed at which cavitation occurs may be delayed to an appreciable extent by the use of suitable sections.

Ward, Kenneth E.↗