Search NASA⌕ Search

SEARCH · Search NASA

Results for “SHOCK TUNNEL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Shock/shock interference on a transpiration cooled hemispherical model

Experimental results are presented which show the effectiveness of transpiration cooling in reducing the peak heat flux caused by an impinging shock on a bow shock of a hemispherical model. The 12-inch diameter hemispherical transpiration model with helium coolant was tested in the Calspan 48-inch Hypersonic Shock Tunnel at nominal Mach 12.1 and freestream unit Reynolds number of 0.33 x 10 to the 6th/ft. An incident shock wave, generated by a blunt flat-plate shock generator inclined at 10 deg to the freestream, intersected the bow shock of the model to produce shock/shock interference. The stagnation heat flux without coolant or shock/shock interference was about 1.6 times a smooth surface laminar prediction due to effective roughness of the coolant ejection slots. A coolant mass flux 31 percent of the freestream mass flux reduced the stagnation heat flux to zero without shock/shock interference. However, for the same coolant mass flux and with shock/shock interference the peak heat flux was only reduced 8.3 percent, even though the total integrated heat load was reduced.

Nowak, Robert J.↗
NASA NTRS1974

Correlation parameters for the study of leeside heating on a lifting body at hypersonic speeds

Leeside heating was studied with the aim of gaining some insight into: (1) the magnitude of the leeside heating rates and (2) the methods to be used to extrapolate wind tunnel leeside heating rates to the full scale flight condition. This study was based on existing experimental data obtained in a hypersonic shock tunnel on lifting body configurations that are typical of shuttle orbiter vehicles. Heat transfer was first measured on the windward side to determine the boundary layer type. Then the leeside heating was investigated with the classified boundary layer. Correlation data are given on the windward turbulent boundary layer, the windward laminar boundary layer, and the leeside surfaces.

Vidal, R. J.↗
NASA NTRS1989

Experimental study of pressure and heating rate on a swept cylindrical leading edge resulting from swept shock wave interference

The effects of cylindrical leading edge sweep on surface pressure and heat transfer rate for swept shock wave interference were investigated. Experimental tests were conducted in the Calspan 48-inch Hypersonic Shock Tunnel at a nominal Mach number of 8, nominal unit Reynolds number of 1.5 x 10 to the 6th power per foot, leading edge and incident shock generator sweep angles of 0, 15, and 30 deg, and incident shock generator angle-of-attack fixed at 12.5 deg. Detailed surface pressure and heat transfer rate on the cylindircal leading edge of a swept shock wave interference model were measured at the region of the maximum surface pressure and heat transfer rate. Results show that pressure and heat transfer rate on the cylindrical leading edge of the shock wave interference model were reduced as the sweep was increased over the range of tested parameters. Peak surface pressure and heat transfer rate on the cylinder were about 10 and 30 times the undisturbed flow stagnation point value, respectively, for the 0 deg sweep test. A comparison of the 15 and 30 deg swept results with the 0 deg swept results showed that peak pressure was reduced about 13 percent and 44 percent, respectively, and peak heat transfer rate was reduced about 7 percent and 27 percent, respectively.

Glass, Christopher E.↗
NASA NTRS1995

Scaling in a scramjet combustor

Studies of scramjet combustor scaling have been extended to include testing of a 'small' combustor, thereby allowing comparison with results obtained in a 'large' combustor of nearly identical configuration. The scale of the two combustors varied by a factor of 5. It was anticipated that the combustion process would scale as the product of pressure with length if the temperature, the Mach number, the velocity, the free stream composition and the equivalence ratio were the same. To achieve this while allowing for the necessary difference in pressure the two models were tested with different shock tunnel nozzles. The large was tested in a M = 8 nozzle, with an intake consisting of a pair of opposing wedges preceding the model, which produced shocks to reduce the Mach number to approximately 3.4 before the flow entered the model inlet. It was then expanded to raise the Mach number again. The small model was tested in a M = 4 nozzle, with the nozzle flow passing directly to the inlet of the model. The wedge intake for the large model was adjusted to yield similar combustion chamber Mach number for both models. Then, by matching the stagnation enthalpy, it was possible also to match the temperature and the velocity. The free stream composition was matched by operating at the same nozzle supply pressure. Wall pressure distributions were measured along each of the ducts. The pressure is normalized with respect to the pressure measured at the point opposite to the injector exit, and the distance downstream of the exit is normalized with respect to the height of the duct. It can be seen that, when normalized in this manner, both ducts produce quantitatively similar pressure distributions, confirming the initial hypothesis that the combustion process would scale as the product of pressure with length.

Pulsonetti, M. V.↗
NASA NTRS1985

AOTV bow shock location

Hypersonic bow-shock location and geometry are of central importance to the aerodynamics and aerothermodynamics of aeroassisted orbital transfer vehicles (AOTVs), but they are difficult to predict for a given vehicle configuration. This paper reports experimental measurements of shock standoff distance for the 70 deg cone AOTV configuration in shock-tunnel-test flows at Mach numbers of 3.8 to 7.9 and for angles of attack from 0 deg to 20 deg. The controlling parameter for hypersonic bow-shock standoff distance (for a given forebody shape) is the mean normal-shock density ratio. Values for this parameter in the tests reported are in the same range as those of the drag-brake AOTV perigee regime. Results for standoff distance are compared with those previously reported in the literature for this AOTV configuration. It is concluded that the AOTV shock standoff distance for the conical configuration, based on frustrum (base) radius, is equivalent to that of a sphere with a radius about 35 percent greater than that of the cone; the distance is, therefore, much less than reported in previous studies. Some reasons for the discrepancies between the present and previous are advanced. The smaller standoff distance determined here implies there will be less radiative heat transfer than was previously expected.

Desautel, D.↗
NASA NTRS1997

Transition and Turbulence Modeling for Blunt-Body Wake Flows

Aerobraking has been proposed as an efficient means of decelerating spacecraft for planetary missions. Most current aerobrake designs feature a blunt forebody shielding the payload from the intense heat generated during atmospheric entry. Although this forebody will absorb the largest portion of the heat pulse, accurate prediction of heating in the near wake is of great importance, since large local heating values can occur at points of shear-layer impingement. In order to address the various issues associated with these blunt-body wake flowfields, the Advisory Group for Aerospace Research and Development (AGARD) formed Working Group 18 in 1992. One of the objectives of this activity was to examine real-gas effects in high-speed flow fields around a 70 deg. blunted cone. To date, many researchers have conducted experiments using this geometry in various facilities, such as the Large Energy National Shock (LENS) tunnel at Cubric/Calspan and the HEG shock tunnel at DLR-Goettingen. Several computational studies have also been conducted in concert with these tests. Many of the experimental results have indicated the possible presence of a transitional shear layer through a large increase in heat transfer downstream of the reattachment point. The presence of transition could in fact lead to much higher peak heating than if the separated flow is entirely laminar or turbulent. In the shock-tunnel tests, however, it is difficult to separate such viscous-flow phenomena from real-gas effects. In order to help make this distinction, Horvath et al. recently conducted a set of experiments in the NASA Langley 20-Inch Mach 6 Tunnel, and compared the results to laminar Navier-Stokes calculations. They found heat-transfer distributions similar to those obtained in the high-enthalpy facilities, with the measured peak heating along the sting support markedly greater than that predicted by the laminar computations. These trends point to the need to find transitional and turbulent computational solutions for these flowfields.

Nance, Robert P.↗
NASA NTRS1991

On the scale of surface features in hypersonic swept shock boundary-layer interactions

A parametric study of a Mach 8 fin-induced shock interaction with a turbulent boundary layer was performed in a shock tunnel using surface oil-dot visualization and surface pressure measurements. The study showed that the interaction was separated and secondary separation was detected for the strongest cases studied. Although the inviscid shock wave was close to the fin, the interaction was spread over large angular extents. The interaction showed inception to conical symmetry at the highest shock strengths. Additionally, the surface pressure distribution showed an extensive plateau region, with no distinct dip associated with strongly separated interactions. Between the fin and the inviscid shock, the surface pressure rose rapidly but did not approach the downstream inviscid shock, the surface pressure rose rapidly but did not approach the downstream inviscid value.

Pace, E. G.↗
NASA NTRS1996

Blunt body near wake flow field at Mach 6

Tests were conducted in a Mach 6 flow to examine the reattachment process of an axisymmetric free shear layer associated with the near wake of a 70 deg. half angle, spherically blunted cone with a cylindrical after body. Model angle of incidence was fixed at 0 deg. and free-stream Reynolds numbers based on body diameter ranged from 0.5 x 10(exp 6) to 4 x 10(exp 6). The sensitivity of wake shear layer transition on reattachment heating was investigated. The present perfect gas study was designed to compliment results obtained previously in facilities capable of producing real gas effects. The instrumented blunted cone model was designed primarily for testing in high enthalpy hypervelocity shock tunnels in both this country and abroad but was amenable for testing in conventional hypersonic blowdown wind tunnels as well. Surface heating rates were inferred from temperature - time histories from coaxial surface thermocouples on the model forebody and thin film resistance gages along the model base and cylindrical after body. General flow feature (bow shock, wake shear layer, and recompression shock) locations were visually identified by schlieren photography. Mean shear layer position and growth were determined from intrusive pitot pressure surveys. In addition, wake surveys with a constant temperature hot-wire anemometer were utilized to qualitatively characterize the state of the shear layer prior to reattachment. Experimental results were compared to laminar perfect gas predictions provided by a 3-D Navier Stokes code (NSHYP). Shear layer impingement on the instrumented cylindrical after body resulted in a localized heating maximum that was 21 to 29 percent of the forebody stagnation point heating. Peak heating resulting from the reattaching shear layer was found to be a factor of 2 higher than laminar predictions, which suggested a transitional shear layer. Schlieren flow visualization and fluctuating voltage time histories and spectra from the hot wire surveys across the shear layer substantiate this observation. The sensitivity of surface heating to forebody roughness was characterized for a reattaching shear layer. For example, at R(sub infinity), d = 4 x 10(exp 6), when the shear layer was transitional, the magnitude of peak heating from shear layer impingement was reduced by approximately 24 percent when transition grit was applied to the forebody. The spatial location of the local peak, however, remained unchanged.

Horvath, Thomas J.↗
NASA NTRS1981

An experimental study of massive blowing from a nosetip during Jovian entry

The fluid dynamic structure and stability of the boundary layer and shock layer ahead of a highly blowing heat shield in an environment simulating entry into the Jovian atmosphere were investigated. The experimental studies were conducted in the Calspan 96 in shock tunnel with a freestream of a H2/He mixture at Mach numbers above 10. Measurements of heat transfer and pressure were made on the porous model surface, and high-speed schlieren photography was used to examine the structure and stability of the shock layer. Results are presented which show how the heat transfer and shock layer stability vary for gases of different molecular weights for a range of Reynolds numbers and mass-addition rates.

Holden, M. S.↗
NASA NTRS1995

Hydrogen film cooling with incident and swept-shock interactions in a Mach 6.4 nitrogen free stream

The effectiveness of slot film cooling of a flat plate in a Mach 6.4 flow with and without incident and swept oblique shock interactions was experimentally investigated. Hydrogen was the primary coolant gas, although some tests were conducted using helium as the coolant. Tests were conducted in the Calspan 48-Inch Shock Tunnel with a nitrogen flow field to preclude combustion of the hydrogen coolant gas. A two-dimensional highly instrumented model developed in a previous test series was used. Parameters investigated included coolant mass flow rate, coolant gas, local free-stream Reynolds number, incident oblique shock strength, and a swept oblique shock. Both gases were highly effective coolants in undisturbed flow; however, both incident and swept shocks degraded that effectiveness.

Olsen, George C.↗
NASA NTRS1974

Vibrational relaxation in expanding N2 and air

New N2 vibrational temperature data, obtained in expanding N2 and air using the electron beam technique, are analyzed permitting the vibrational relaxation times to be determined as a function of temperature. In addition, the effects on N2 vibrational relaxation times of direct vibrational energy transfer between N2 and H2O, between N2 and O2, and between N2 and free electrons introduced from arc contaminants are analyzed. The vibrational relaxation times determined from the present measurements agree with those measured in the expanding flows of shock tunnels and impact tubes. These expanding data also agree with relaxation times observed in acoustical resonant cavities where alternating compressions and expansions take place. The relaxation times in expanding flows (vib-tran exchange process) are found to be approximately 50 times faster than those measured in the compressing flow of shock tubes (tran-vib exchange process). This evidence strongly supports the concept that one relaxation time distribution cannot be applied to both exchange processes.

Sebacher, D. I.↗
NASA NTRS1972

A review of the Grumman orbiter wind tunnel heat transfer tests

Tests were conducted in the NASA Langley continuous flow, variable density and Mach 20 helium tunnels. The orbiter was tested alone and with various side and tandem mounted tanks. Test conditions spanned a Reynolds number range which resulted in both laminar and turbulent flows. Experimental studies also examined the heat transfer problems associated with integration of the auxiliary propulsion system into the orbiter. Tests in the hypersonic shock tunnel investigated heating to cavities and heating from single and multiple hydrogen-oxygen plumes while tests, run as part of the configuration evaluation, examined the heating to wing pods.

Mendelsohn, A. R.↗
NASA NTRS1992

Experimental studies of hypersonic shock-wave boundary-layer interactions

Two classes of shock-wave boundary-layer interactions were studied experimentally in a shock tunnel in which a low Reynolds number, turbulent flow at Mach 8 was developed on a cold, flat test surface. The two classes of interactions were: (1) a swept interaction generated by a wedge ('fin') mounted perpendicularly on the flat plate; and (2) a two-dimensional, unseparated interaction induced by a shock impinging near an expansion corner. The swept interaction, with wedge angles of 5-20 degrees, was separated and there was also indication that the strongest interactions prossessed secondary separation zones. The interaction spread out extensively from the inviscid shock location although no indication of quasi-conical symmetry was evident. The surface pressure from the upstream influence to the inviscid shock was relatively low compared to the inviscid downstream value but it rose rapidly past the inviscid shock location. However, the surface pressure did not reach the downstream inviscid value and reasons were proposed for this anomalous behavior compared to strongly separated, supersonic interactions. The second class of interactions involved weak shocks impinging near small expansion corners. As a prelude to studying this interaction, a hypersonic similarity parameter was identified for the pure, expansion corner flow. The expansion corner severely damped out surface pressure fluctuations. When a shock impinged upstream of the corner, no significant changes to the surface pressure were found as compared to the case when the shock impinged on a flat plate. But, when the shock impinged downstream of the corner, a close coupling existed between the two wave systems, unlike the supersonic case. This close coupling modified the upstream influence. Regardless of whether the shock impinged ahead or behind the corner, the downstream region was affected by the close coupling between the shock and the expansion. Not only was the mean pressure distribution modified but the unsteadiness in the surface pressure was reduced compared to the flat-plate case.

Lu, Frank K.↗
NASA NTRS1991

Aerothermodynamic environment predictions in support of the Aeroassist Flight Experiment

A computational fluid dynamic (CFD) simulation has been made of the flow past an Aeroassist Flight Experiment (AFE) aerobrake model with a payload and sting. The simulation involves solving the complete Navier-Stokes equations in three dimensions. Comparisons with data taken in a Mach 10 wind tunnel test are made and agreement is shown to be very good. Points of comparison include the aerobrake surface pressure and heat transfer rate, the sting surface streamlines, and the sting heat transfer rate. The dependence of the solution on the grid is also explored. Finally, predictions are made for conditions which correspond to a hypersonic shock tunnel force and moment test to be carried out later this year.

Fay, John F.↗
NASA NTRS1987

Study of non-equilibrium transport phenomena

Nonequilibrium phenomena due to real gas effects are very important features of low density hypersonic flows. The shock shape and emitted nonequilibrium radiation are identified as the bulk flow behavior parameters which are very sensitive to the nonequilibrium phenomena. These parameters can be measured in shock tubes, shock tunnels, and ballistic ranges and used to test the accuracy of computational fluid dynamic (CFD) codes. Since the CDF codes, by necessity, are based on multi-temperature models, it is also desirable to measure various temperatures, most importantly, the vibrational temperature. The CFD codes would require high temperature rate constants, which are not available at present. Experiments conducted at the NASA Electric Arc-driven Shock Tube (EAST) facility reveal that radiation from steel contaminants overwhelm the radiation from the test gas. For the measurement of radiation and the chemical parameters, further investigation and then appropriate modifications of the EAST facility are required.

Sharma, Surendra P.↗
NASA NTRS1992

A database of aerothermal measurements in hypersonic flow for CFD validation

This paper presents an experimental database selected and compiled from aerothermal measurements obtained on basic model configurations on which fundamental flow phenomena could be most easily examined. The experimental studies were conducted in hypersonic flows in 48-inch, 96-inch, and 6-foot shock tunnels. A special computer program was constructed to provide easy access to the measurements in the database as well as the means to plot the measurements and compare them with imported data. The database contains tabulations of model configurations, freestream conditions, and measurements of heat transfer, pressure, and skin friction for each of the studies selected for inclusion. The first segment contains measurements in laminar flow emphasizing shock-wave boundary-layer interaction. In the second segment, measurements in transitional flows over flat plates and cones are given. The third segment comprises measurements in regions of shock-wave/turbulent-boundary-layer interactions. Studies of the effects of surface roughness of nosetips and conical afterbodies are presented in the fourth segment of the database. Detailed measurements in regions of shock/shock boundary layer interaction are contained in the fifth segment. Measurements in regions of wall jet and transpiration cooling are presented in the final two segments.

Holden, M. S.↗
NASA NTRS1971

Sharp flat plate heat transfer in helium at Mach numbers of 22.8 to 86.8 and in corner flow with air at Mach number of 19

Surface heat transfer rates were measured on a sharp flat plate at zero angle of attack in a hypersonic shock tunnel. The density and leading edge Knudsen number were varied to span the continuum to near free molecule regimes. The strong interaction parameter varied from 11 to 16,000 with Knudsen numbers from 0.56 to 17.1 respectively. Local heat transfer rates in the corner flow region produced by the intersection of two perpendicular flat plates with sharp leading edges were determined for various flow densities. The strength of the shock wave from the vertical plate was varied by adjusting the angle of attack from 0 to 5 deg. The unit Reynolds number varied from 1,000 to 17,200 and the Knudsen numbers from 1.6 to 27. The strong interaction parameter varied from 14 to 500.

Nagamatsu, H. T.↗