Search NASA⌕ Search

SEARCH · Search NASA

Results for “STEELS, STAINLESS - REZISTAL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Oxidation of porous stainless steel supports for metal-supported solid oxide electrolysis cells

Oxidation behavior of porous P434L ferritic stainless steel, used for the fabrication of metal-supported solid oxide electrolysis cells (MS-SOEC), is studied under oxygen-side and steam-side conditions. The impact of oxygen content on the oxygen side and steam:hydrogen ratio on the steam side is determined at 700°C for bare, as-sintered samples. For these conditions, oxidation is more aggressive in the steam-side atmosphere. Oxygen with 3% humidification and steam:hydrogen ratio of 90:10 are selected for further assessment with pre-oxidized, catalyst-coated, and CuMn1·8O4-coated samples. The rapid oxidation at 700°C and breakaway oxidation at 600 °C observed for bare stainless steel in 90:10 steam:hydrogen is mitigated by pre-oxidizing the sample in air before exposure. In oxygen, addition of the catalyst or CuMn 1·8 O 4 coatings moderately increases the oxidation rate, due to consumption of Cr via reaction between the coatings and Cr-oxide scale. In conclusion, the results for ex-situ controlled oxidation are similar to oxidation observed after 1000h operation of a full MS-SOEC. In general, the oxidation behavior at 700°C is found to be acceptable.

08 HYDROGEN↗
DOE OSTI2020

Oxidation of porous stainless steel supports for metal-supported solid oxide fuel cells

Here, oxidation behavior of porous P434L ferritic stainless steel, used for the fabrication of metal-supported solid oxide fuel cells (MS-SOFC), is studied under anodic and cathodic atmospheres. Temperature- and atmosphere-dependence is determined for as-sintered and pre-oxidized stainless steel. Pre-oxidation reduced the long-term oxidation rate. For pre-oxidized samples, the oxidation rate in air exceeds that in humid hydrogen for temperatures above 700 °C. The influence of PrOx, LSCF-SDC, and Ni-SDC coatings is also examined. The coatings do not dramatically impact oxide scale growth. Oxidation in C-free and C-containing anodic atmospheres is similar. Addition of CO 2 , CH 4 , and CO to humidified hydrogen to simulate ethanol reformate does not significantly impact oxidation behavior. Cr transpiration in humid air is greatly reduced by the PrOx coating, and a PrCrO 3 reaction product is observed throughout the porous structure. A dense and protective chromia-based scale forms on steel samples during oxidation in all conditions. A thin silica enriched oxide layer also forms at the metal-scale interface. In general, the oxidation behavior at 700 °C is found to be acceptable.

25 ENERGY STORAGE↗
DOE OSTI2024

Stress relaxation cracking susceptibility evaluation in 347H stainless steel welds

Abstract Stress relaxation cracking (SRC) has been reported as a dominant failure mechanism for 347H stainless steel welds at elevated service temperatures, occurring in either the heat-affected zone (HAZ) or fusion zone (FZ). In this study, SRC susceptibility of physically simulated HAZ and cross-welded E347-347H stainless steel welds was studied using a four-step accelerated SRC test with a thermomechanical physical simulator. The stress and temperature range studied represents weld-induced residual stress at 150–600 MPa and post-weld heat treatment temperatures between 800 and 1050 °C. For all temperature conditions, the cross-welded samples failed at a lower critical stress threshold than the simulated HAZ. A finite element model of a 50.8-mm-thick single-V groove weld was used to generate the residual stress maps induced by a 40-pass welding procedure, which in combination with the experimental threshold stress map predicted potential SRC failure locations. Postmortem microstructural evaluations were performed to identify contributing characteristics to SRC. It was found that HAZ samples exhibited a combination of creep void development, secondary cracks with intergranular fracture near grain boundary carbides, and eutectic phases. FZ samples showed brittle fracture with cracks propagating along straight, non-tortuous interdendritic grain boundaries.

42 ENGINEERING↗
NASA NTRS1985

Corrosion behavior of surface films on boron-implanted high purity iron and stainless steels

Boron (dose, 2 x 10 to the 17th ions/sq cm) was implanted into high purity iron, AISI 316 austenitic stainless steel, and AISI 440C martensitic stainless steel, at 40 keV. The film structure of implanted samples was examined and characterized by contrast and diffraction analyses utilizing transmission electron microscopy. The effect of B(+) ion implantation on the corrosion behavior was studied using the potentiodynamic polarization technique. Tests were performed in deaerated 1 N H2SO4 and 0.1 M NaCl solutions. Scanning electron microscopy was used to examine the morphology of the corroded surfaces after testing.

Kim, H. J.↗
NASA NTRS1970

Optimum outgassing cycles for aluminum and stainless steel

Outgassing rates were measured for a modified 7075T6 aluminum and 304L stainless steel, for two degrees of finish, at temperatures of 285 deg F to 392 deg F, for times of 0.5 to 72 hours. The results were analyzed to determine optimum time and temperature cycles for outgassing. Optimum cycles were determined with and without the limitations of a graph. The graph related allowable time at temperature to a 5 percent or less reduction in room temperature properties of 7075T6 aluminum. For aluminum, within the limits set by reduction in mechanical properties, the optimum cycle tested was 40 hours at 285 deg F. Disregarding the limits, optimum outgassing was achieved at the highest temperatures and longest times tested, for both aluminum and stainless steel.

Garrison, R. L.↗
NASA NTRS2009

Citric Acid Passivation of Stainless Steel

Passivation is a process for cleaning and providing corrosion protection for stainless steel. Currently, on Kennedy Space Center (KSC), only parts passivated with nitric acid are acceptable for use. KSC disposes of approximately 125gal of concentrated nitric acid per year, and receives many parts from vendors who must also dispose of used nitric acid. Unfortunately, nitric acid presents health and environmental hazards. As a result, several recent industry studies have examined citric acid as an alternative. Implementing a citric acid-based passivation procedure would improve the health and environmental safety aspects of passivation process. However although there is a lack of published studies that conclusively prove citric acid is a technically sound passivation agent. In 2007, NASA's KSC Materials Advisory Working Group requested the evaluation of citric acid in place of nitric acid for passivation of parts at KSC. United Space Alliance Materials & Processes engineers have developed a three-phase test plan to evaluate citric acid as an alternative to nitric acid on three stainless steels commonly used at KSC: UNS S30400, S41000, and S17400. Phases 1 and 2 will produce an optimized citric acid treatment based on results from atmospheric exposure at NASA's Beach Corrosion Facility. Phase 3 will compare the optimized solution(s) with nitric acid treatments. If the results indicate that citric acid passivates as well or better than nitric acid, NASA intends to approve this method for parts used at the Kennedy Space Center.

Yasensky, David↗
DOE OSTI2026

Model Parameter Development for Complex Materials: Species-Specific Diffusion Barriers in 316 Stainless Steel from Systematic DFT Calculations

Vacancy-mediated diffusion barriers in 316 stainless steel have been systematically calculated using density functional theory to provide essential parameters for mesoscale microstructure evolution models. A statistical sampling approach employing 210 nudged elastic band calculations across multiple special quasi-random structures captures the effects of local chemical environments in this concentrated alloy. The computational methodology addresses challenges specific to chemically disordered systems, including proper magnetic treatment throughout multi-step calculations and validation against experimental structural properties. The calculated activation barriers reveal clear species-dependent diffusion behavior with the hierarchy Ni >> Fe ˜ Cr >> Mo. Nickel exhibits the highest barriers (0.74–1.31 eV, mean 1.045 eV), confirming its role as the slowest-diffusing major component. Iron and chromium show similar moderate barriers averaging 0.587 eV and 0.522 eV, respectively. Remarkably, molybdenum demonstrates exceptionally low barriers (0.12–0.28 eV, mean 0.194 eV), suggesting much higher mobility than previously recognized and potentially significant implications for precipitation kinetics and microstructure evolution. The barrier ranges remain consistent across different 316 SS compositions, supporting parameter transferability for modeling applications. The overall mean barrier of 0.64 eV provides a practical approximation for phase field simulations, while species-specific values enable detailed treatments of diffusion-controlled processes. This systematic approach establishes a validated framework for generating diffusion parameters in other concentrated alloys where experimental data are limited, while providing the first systematic set of species-specific barriers for predictive modeling of 316 stainless steel microstructure evolution.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Investigation of Microstructures and Tensile Properties of 316L Stainless Steel Fabricated via Laser Powder Bed Fusion

In this study, a thorough investigation of the microstructures and tensile properties of 316L stainless steel fabricated via laser powder bed fusion (L-PBF) was done. 316L stainless steel specimens with two different thicknesses of 1.5 mm and 4.0 mm fabricated under similar conditions were utilized. Microstructural characterization was performed using optical microscopy (OM) and scanning electron microscopy (SEM) equipped with electron backscatter diffraction (EBSD). Melt pools and cellular structures were observed using OM, whereas EBSD was utilized to obtain the grain size, grain boundary characteristics, and crystallographic texture. The 1.5 mm thick sample demonstrated a yield strength (YS) of 538.42 MPa, ultimate tensile strength (UTS) of 606.47 MPa, and elongation to failure of 69.88%, whereas the 4.0 mm thick sample had a YS of 551.21 MPa, UTS of 619.58 MPa, and elongation to failure of 73.66%. These results demonstrated a slight decrease in mechanical properties with decreasing thickness, with a 2.4% reduction in YS, 2.1% reduction in UTS, and 5.8% reduction in elongation to failure. In addition to other microstructural features, the cellular structures were observed to be the major contributors to the high mechanical properties. Using the inverse pole figure (IPF) maps, both thicknesses depicted a crystallographic texture of {001} <101> in their as-built state. However, when subjected to tensile loads, texture transitions to {111} <001> and {111} <011> were observed for the 1.5 mm and 4.0 mm samples, respectively. Additionally, EBSD analysis revealed the pre-existence of high-density dislocation networks and a high fraction of low-angle grain boundaries. Interestingly, twinning was observed, suggesting that the plastic deformation occurred through dislocation gliding and deformation twinning.

316L stainless steel↗
DOE OSTI2024

Monte Carlo Simulations of 347H Stainless Steel Aging for the Synthetic Generation of Microstructures Under Creep Conditions

Here, a Monte Carlo simulation method capable of replicating the kinetics of M 23 C 6 precipitation in 347H stainless steels was developed for the purpose of producing synthetic microstructures that approximate its microstructural evolution under aging periods of up to 10,000 hours at temperatures between 600 °C and 750 °C. To accomplish this, experimental data from the literature was used to parameterize simulations and replicate the nucleation and growth kinetics of M 23 C 6 particles within 347H and similar austenitic stainless steel alloys. These simulations were found to have considerable fidelity to previous efforts to study the precipitation of M 23 C 6 in other 300 series stainless steel alloys. Synthetic 347H microstructures were then generated that accounted the effects of aging temperature, duration, dislocation density, and the presence of boron within the microstructure. These simulations predict several key trends, those being that (1) the size of M 23 C 6 precipitates decreased with aging temperature and (2) the growth rate of M 23 C 6 particles decreased with aging temperature. Further, while (3) the addition of dislocation density due to creep conditions resulted in increasing intragranular nucleation of M 23 C 6 precipitates with increasing dislocation density and (4) B additions within the microstructure led to modest increases in precipitate size above 700 °C, which indicates that more complex physics are necessary to account for the presence of B.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Fabrication and Testing of a Stainless Steel Quartz Coaxial Cable Structure for High Temperature Measurement

This paper presents a stainless-steel quartz coaxial cable structure for distributed sensing of high temperatures. The coaxial cable sensor uses stainless steel as the inner and outer conductors and quartz as the insulator in order to achieve mechanical strength and temperature resilience. Girdle-shaped reflectors are fabricated on the quartz tubing by CNC grinding and CO 2 laser resurfacing. The sensor operates by measuring the temperature dependent change in the effective electromagnetic length between the two adjacent reflectors on the quartz tubing. A retaining collar is fabricated at the tip of the quartz tubing by 3D printing and laser resurfacing to secure the connection between the sensor and the signal cable. The prototype sensor was tested for high temperature measurements up to 600°C, and the performance characteristics of the sensor such as sensitivity, resolution uncertainty, repeatability, and stability were estimated based on the test results.

Jiao, Xinyu↗
DOE OSTI2022

Enhanced crevice corrosion of stainless steel 316 by degradation of Cr-containing hollandite crevice former

This study explores the corrosion interactions between stainless steel 316 (SS316), a candidate nuclear waste canister material, and Cr-containing hollandite (Ba 1.15 Cr 2.3 Ti 5.7 O 16 ), a model ceramic nuclear waste form. The two materials were corroded in close proximity in 0.6 M NaCl solution at 90 °C for 28 days. Severe crevice corrosion was observed on the stainless steel surface after the corrosion experiment, which is likely associated with the rapid accumulation of Cr 3+ cations originating from both SS316 and the Cr-containing hollandite. Furthermore, the enhanced corrosion of SS316 by the corrosion products of hollandite is quantitatively explained using a classical crevice corrosion model.

36 MATERIALS SCIENCE↗
NASA NTRS1976

Low-cycle fatigue of Type 347 stainless steel and Hastelloy alloy X in hydrogen gas and in air at elevated temperatures

An investigation was conducted to assess the low-cycle fatigue resistance of two alloys, Type 347 stainless steel and Hastelloy Alloy X, that were under consideration for use in nuclear-powered rocket vehicles. Constant-amplitude, strain-controlled fatigue tests were conducted under compressive strain cycling at a constant strain rate of 0.001/sec and at total axial strain ranges of 1.5, 3.0, and 5.0 %, in both laboratory-air and low-pressure hydrogen-gas environments at temperatures from 538 to 871 C. Specimens were obtained from three heats of Type 347 stainless steel bar and two heats of Hastelloy Alloy X. The tensile properties of each heat were determined at 21, 538, 649, and 760 C. The continuous cycling fatigue resistance was determined for each heat at temperatures of 538, 760, and 871 C. The Type 347 stainless steel exhibited equal or superior fatigue resistance to the Hastelloy Alloy X at all conditions of this study.

Jaske, C. E.↗
DOE OSTI2021

Impact of neutron irradiation on the thermophysical properties of additively manufactured stainless steel and inconel

The deployment of additive manufacturing (AM) technologies to support the nuclear energy industry is limited by the current lack of data related to the irradiation performance of AM parts. The Colorado School of Mines is conducting a multi-year irradiation and post irradiation examination project to study the impacts of neutron irradiation on stainless steel 316L and Inconel 718 and 625 specimens produced by several commercially available AM techniques and irradiated in the Advanced Test Reactor (ATR) at the Idaho National Laboratory (INL). This paper presents initial results on the impact of neutron irradiation on the heat capacity, the thermal diffusivity, and the thermal conductivity of the specimens at temperatures between 100 oC and 400 oC. The unirradiated AM specimens have heat capacity values similar to, or lower than, the reference values, regardless of manufacturing method or material. The irradiated AM specimens have average heat capacities greater than the unirradiated specimens and reference values in every case. Additionally, the thermal diffusivities of the unirradiated AM specimens are either larger or statistically similar to the reference values. The irradiated AM specimens exhibit lower thermal diffusivities compared to the reference thermal diffusivity values. One of the stainless steel 316L laser powder bed fusion samples exhibited thermal diffusivity values with statistically significant anisotropy prior to and after irradiation. The thermal conductivities of the unirradiated AM stainless steel 316L specimens and the unirradiated Inconel 718 specimens are lower or statistically similar to the reference values. The unirradiated Inconel 625 specimens exhibit slightly higher thermal conductivity values than the reference values. The irradiated specimens show a significant increase in thermal conductivity compared to the unirradiated specimens and the reference values for all materials.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Electrochemical Corrosion Analysis of Stainless Steels in LALM Pyrolysis Bio-Oil with Organic Corrodents

Pyrolysis bio-oils are corrosive to low alloy steels, e.g., 2.25Cr-1Mo, 5Cr-1Mo, and 9Cr-1Mo grades. To identify the alloys with sufficient bio-oil compatibility, several commercial stainless steels were examined in bio-oil using electrochemical impedance spectroscopy to semi quantitatively assess their corrosion resistance. Low-Ash Low-Moisture (LALM) bio-oil, produced from a forest residue feedstock by the National Renewable Energy Laboratory in Golden, CO, was used as a test liquid for electrochemical impedance spectroscopy measurements. Three organic corrodents, formic acid, catechol, and lactobionic acid, were added into LALM bio-oil to produce test liquids with intentionally increased corrosivity. Corrosion reaction resistance, determined from the impedance data, was used to evaluate the corrosion compatibility of each stainless steel in LALM bio-oil and LALM bio-oil + organic corrodent(s). The results from corrosion reaction resistance indicated that the critical Cr content of stainless steels for corrosion resistance would be greater than 14 wt % if Ni and Mo contents are low but can be as low as 12–13 wt % with appreciable amounts of Ni and Mo.

Jun, Jiheon↗
DOE OSTI2026

Effect of deposition rate on microstructure and mechanical properties of 17-4 PH stainless steel fabricated by laser engineered net shaping

Laser engineered net shaping (LENS) is an additive manufacturing technique for fabricating and repairing metallic components. However, the relationships between its process parameters and the resulting mechanical properties of alloys such as 17-4 precipitation-hardening (PH) stainless steel require further investigation to enable reliable application. This study examines the specific effect of LENS deposition rate on the microstructure and mechanical properties of 17-4 PH stainless steel. Specimens were fabricated at two different deposition rates (8.47 and 9.31 mm s−1), subjected to subsequent solution and H900 aging treatment, and then evaluated via tensile testing, hardness measurements, and microscopy. A higher deposition rate results in a finer grain structure but increased porosity, leading to greater ultimate tensile strength (∼1294 MPa) yet lower ductility (strain at failure ∼5.8%) compared to the slower deposition rate (∼1266 MPa, ∼9.0% strain). Hardness follows the same trend as tensile strength. Tensile fracture surfaces for both conditions exhibited a mixed mode of ductile dimples and brittle quasi-cleavage regions, with chromium/silicon oxide particles identified within dimples. Complementary finite element modeling indicates that small void fractions primarily reduce ductility by enhancing localized plasticity, with only a marginal decrease in tensile strength. These integrated experimental and numerical results elucidate the mechanical properties linked to deposition rate, providing insight into tailoring LENS processes to achieve desired properties of 17-4 PH stainless steel.

17-4 PH stainlesssteel↗