Search NASA⌕ Search

SEARCH · Search NASA

Results for “STEELS, STAINLESS - WELDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Surface integrity and fatigue behaviour of electric discharged machined and milled austenitic stainless steel

Machining of austenitic stainless steels can result in different surface integrities and different machining process parameters will have a great impact on the component fatigue life. Understanding how machining processes affect the cyclic behaviour and microstructure are of outmost importance in order to improve existing and new life estimation models. Milling and electrical discharge machining (EDM) have been used to manufacture rectangular four-point bend fatigue test samples; subjected to high cycle fatigue. Before fatigue testing, surface integrity characterisation of the two surface conditions was conducted using scanning electron microscopy, surface roughness, residual stress profiles, and hardness profiles. Differences in cyclic behaviour were observed between the two surface conditions by the fatigue testing. The milled samples exhibited a fatigue limit. EDM samples did not show the same behaviour due to ratcheting. Recrystallized nano sized grains were identified at the severely plastically deformed surface of the milled samples. Large amounts of bent mechanical twins were observed ~ 5 μm below the surface. Grain shearing and subsequent grain rotation from milling bent the mechanical twins. EDM samples showed much less plastic deformation at the surface. Surface tensile residual stresses of ~ 500 MPa and ~ 200 MPa for the milled and EDM samples respectively were measured. - Highlights: •Milled samples exhibit fatigue behaviour, but not EDM samples. •Four-point bending is not suitable for materials exhibiting pronounced ratcheting. •LAGB density can be used to quantitatively measure plastic deformation. •Grain shearing and rotation result in bent mechanical twins. •Nano sized grains evolve due to the heat of the operation.

36 MATERIALS SCIENCE↗

Properties of Austenitic Stainless Steels for Nuclear Reactor Applications

Austenitic stainless steels are widely used in current commercial BWR and PWR systems as in-core and surrounding structural materials. These versatile steels have also been the main materials considered and applied for many advanced reactor technologies, including fast-breeder reactors and magnetic fusion reactors. For advanced reactors for higher-temperatures or high lifetime damage levels, modified versions of the standard commercial stainless steel grades have been developed to provide improved properties performance and radiation-resistance in specific reactor environments. An overview of the unirradiated properties and a summary of some important radiation-induced properties changes are presented. Highlights of several alloys developed for more radiation-resistance or better performance in specific reactor environments are highlighted.

Maziasz, Philip J↗

THE EFFECTS OF HYDROGEN, TRITIUM, AND HEAT TREATMENT ON THE DEFORMATION AND FRACTURE TOUGHNESS PROPERTIES OF STAINLESS STEEL

The deformation and fracture toughness properties of forged stainless steels pre-charged with tritium were compared to the deformation and fracture toughness properties of the same steels heat treated at 773 K or 873 K and precharged with hydrogen. Forged stainless steels pre-charged with tritium exhibit an aging effect: Fracture toughness values decrease with aging time after precharging because of the increase in concentration of helium from tritium decay. This study shows that forged stainless steels given a prior heat treatment and then pre-charged with hydrogen also exhibit an aging effect: Fracture toughness values decrease with increasing time at temperature. A microstructural analysis showed that the fracture toughness reduction in the heat-treated steels was due to patches of recrystallized grains that form within the forged matrix during the heat treatment. The combination of hydrogen and the patches of recrystallized grains resulted in more deformation twinning. Heavy deformation twinning on multiple slip planes was typical for the hydrogen-charged samples; whereas, in the non-charged samples, less twinning was observed and was generally limited to one slip plane. Similar effects occur in tritium pre-charged steels, but the deformation twinning is brought on by the hardening associated with decay helium bubbles in the microstructure.

36 MATERIALS SCIENCE↗

Effects of scan rate on the corrosion behavior SS 304 stainless steel in the nanofluid measured by Tafel polarization methods

The Effects of scan rate on the Tafel polarization curve that is obtained to determine corrosion rate are conducted. The tafel polarization curves are obtained at different scan rates for Stainless Steel 304 in nanofluids contain 0.01 gpl nano particle ZrO{sub 2}. The corrosion stainless steel in nanofluid contains adm+0.01 gpl ZrO{sub 2} nanoparticles at different scan rate was performed by Tafel polarization. The results show that according corrosion potential examination of the stainless steel in nanofluid media 0.01gpl ZrO{sub 2} nanoparticle was actively corroded. The value of cathodic Tafel slope stainless steel in nanofluid at different scan rate relatively unchanged after polarization testing. Mean while the value of anodic Tafel slope stainless steel in nanofluid increase at different scan rate. The results of Tafel polarization technique show that corrosion rate of stainless steel in nanofluid increase with increasing scan rate. X ray diffraction examination of stainless steel after Tafel polarization depict that γ Fe phase is major phase in the surface of alloy.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Crush Strengths of Stainless Steel Honeycomb for Packaging

Honeycomb structures are used as energy absorbers to dissipate kinetic energy. Their low density to high axial strength and inexpensive cost make them ideal for the energy absorption application. Mechanical properties of lightweight materials are well known compared to more dense materials like stainless steel. Determines the viability of using 304 Stainless Steel honeycomb in future SRNL radioactive material packages. Using a combination of the material properties and testing procedures both static and dynamic crush strength of stainless steel honeycomb will be determined. Both static and dynamic crush strengths of stainless steel honeycomb need to be quantified because strain rate plays a role in the material strength. The stainless steel honeycomb being tested will be cut into sections of about 2.0 inches in width, 2.3 inches in length and 2.5 inches in height. The cell size of the material is 0.25 in and the ribbon thickness 0.003 in. The material has a yield strength of 48 ksi and an ultimate strength of 103.2 ksi, with an elastic modulus of 29,300 ksi. Compression testing to determine the static crush strength will use an Instron compression test machine. This Instron machine uses a 20 ksi capacity load cell, while recording data at varying low strain rates. Dynamic impact testing will involve dropping a 43.8 lb impactor from a height around 5 feet onto the stainless steel honeycomb. The honeycomb structure will be on a rigid surface and the impactor will be dropped via a quick release hook. Dynamic crush strength is determined from the weight of the impactor, height of the drop and difference in height of the honeycomb after the drop.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

2017 Status report-Tritium aging studies on stainless steel: Effect of hydrogen, tritium and decay helium on the fracture-toughness properties of stem, cup and block forgings

The materials of construction of tritium reservoirs are forged stainless steels. During service, the structural properties of the stainless steel change over time because of the diffusion of tritium into the reservoir wall and its radioactive decay to helium-3. This aging effect can cause cracks to initiate and grow which could result in a tritium leak or delayed failure of a tritium reservoir. Numerous factors affect the tendency for crack formation and propagation and are being investigated in this program. The goal of the research is to provide relevant fracture mechanics data that can be used by the design agencies in their assessments of tritium reservoir structural integrity. In this status report, new experimental results are presented on the effects of tritium and decay helium on the cracking properties of specimens taken from actual tritium reservoir forgings instead of the experimental forgings of past programs. The properties measured are more representative of actual reservoir properties because the microstructure of the specimens tested are more like that of the actual tritium reservoirs. The program was designed to measure the effects of material variables on tritium compatibility and includes two stainless steels (Type 304L and 316L stainless steel), multiple yield strengths (360-500 MPa), and multiple forging shapes (Stem, Cup, and Block).

36 MATERIALS SCIENCE↗

High temperature oxidation behavior of austenitic stainless steel AISI 304 in steam of nanofluids contain nanoparticle ZrO2

The objective of this study is to evaluate high temperature oxidation behavior of austenitic stainless steel SS 304 in steam of nanofluids contain nanoparticle ZrO{sub 2}. The oxidation was performed at high temperatures ranging from 600 to 800°C. The oxidation time was 60 minutes. After oxidation the surface of the samples was analyzed by different methods including, optical microscope, scanning electron microscope (SEM) and X-ray diffraction (XRD). X-ray diffraction examination show that the oxide scale formed during oxidation of stainless steel AISI 304 alloys is dominated by iron oxide, Fe{sub 2}O{sub 3}. Minor element such as Cr{sub 2}O{sub 3} is also appeared in the diffraction pattern. Characterization by optical microscope showed that cross section microstructure of stainless steel changed after oxidized with the oxide scale on the surface stainless steels. SEM and x-ray diffraction examination show that the oxide of ZrO{sub 2} appeared on the surface of stainless steel. Kinetic rate of oxidation of austenite stainless steel AISI 304 showed that increasing oxidation temperature and time will increase oxidation rate.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Influence of differential speed rolling ratio on the ridging behavior of ultra purified 17%Cr ferritic stainless steel

Highlights: • Differential rolling process improves ridging resistance of ferritic stainless steel. • Texture orientation inhomogeneity were attributed to non-uniform deformation. • Shear bands results in homogeneous deformation and recrystallization nucleation. • Uniform recrystallization grains and random orientation grains were obtained. - Abstract: The effect of the differential speed rolling on the ridging resistance and the crystallographic texture evolution of ultra purified 17%Cr ferritic stainless steel was investigated in order to select the optimal procedure for improving the surface quality. In the present study, the three different cold rolling processes were carried out: a conventional cold rolling and two different speed ratios asymmetric rolling. In the conventional cold rolling, the ridging of ferritic stainless steel was pronounced due to the band-like clusters of grains with similar crystallographic orientations. For differential speed rolling, ridging depth decreased and ridging was less pronounced when a higher different speed ratio was applied. The results show that severe ridging is attributed to the presence of band-like clusters of γ-fiber (<111>//ND) oriented grains. The shear bands introduced by differential speed rolling can enhance the nucleation for recrystallization both in grain interiors and grain boundaries, which can fragment the band-like clusters of similar orientation effectively, promoting the random grain orientation and improving surface quality.

36 MATERIALS SCIENCE↗

Wear and Corrosion Resistances of Active Screen Plasma-Nitrided Duplex Stainless Steels

Two grades of duplex stainless steel, SAF 2205 and SAF 2507, were nitrided using an active screen plasma process carried out at 380 °C for 10 h and were characterized in terms of microstructure and hardness. Wear resistance was assessed by means of linear scratch tests, using loads below and above the critical load. Potentiodynamic polarization was used to analyze corrosion behavior in 0.6 M NaCl solution. X-ray diffractometry showed expanded austenite formation in all nitrided samples. The super duplex steel SAF 2507 showed much better scratch resistance, with low friction coefficient and greater toughness, as judged by the pattern of superficial cracks when it was tested above the critical load. The corrosion behavior of steels was also different, mainly in the active region, and nitriding had a more beneficial effect upon SAF 2507. The potential relative to the transpassive region was practically unaffected by the nitriding.

36 MATERIALS SCIENCE↗

Cracking behavior and microstructure of austenitic stainless steels and alloy 690 irradiated in BOR-60 reactor, phase I.

Cracking behavior of stainless steels specimens irradiated in the BOR-60 at about 320 C is studied. The primary objective of this research is to improve the mechanistic understanding of irradiation-assisted stress corrosion cracking (IASCC) of core internal components under conditions relevant to pressurized water reactors. The current report covers several baseline tests in air, a comparison study in high-dissolved-oxygen environment, and TEM characterization of irradiation defect structure. Slow strain rate tensile (SSRT) tests were conducted in air and in high-dissolved-oxygen (DO) water with selected 5- and 10-dpa specimens. The results in high-DO water were compared with those from earlier tests with identical materials irradiated in the Halden reactor to a similar dose. The SSRT tests produced similar results among different materials irradiated in the Halden and BOR-60 reactors. However, the post-irradiation strength for the BOR-60 specimens was consistently lower than that of the corresponding Halden specimens. The elongation of the BOR-60 specimens was also greater than that of their Halden specimens. Intergranular cracking in high-DO water was consistent for most of the tested materials in the Halden and BOR-60 irradiations. Nonetheless, the BOR-60 irradiation was somewhat less effective in stimulating IG fracture among the tested materials. Microstructural characterization was also carried out using transmission electron microscopy on selected BOR-60 specimens irradiated to {approx}25 dpa. No voids were observed in irradiated austenitic stainless steels and cast stainless steels, while a few voids were found in base and grain-boundary-engineered Alloy 690. All the irradiated microstructures were dominated by a high density of Frank loops, which varied in mean size and density for different alloys.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Characterization of in-situ and ex-situ ion-irradiated additively manufactured 316L and 316H stainless steels

Additively manufactured (AM) 316 stainless steel (SS) differs from its wrought counterpart in its unique dislocation cell structure and the presence of segregation and oxide particles at the cell walls. This work investigated the evolution of the microstructure in laser powder bed fusion (LPBF) 316L and 316H SS under in-situ 1 MeV Kr ion irradiation at 600 °C to 5 dpa, and ex-situ 4 MeV Ni ion irradiation at 300 °C and 600 °C from 0.2 dpa to 10 dpa, with a dose rate for all experiments of 10 -3 dpa/s. The results reveal that the dislocation cell structure results in heterogeneous formation of dislocation loops and voids, particularly at 600 °C, where loops tend to form within the cell interiors while voids form at the cell boundaries. LPBF 316H has a reduced level of swelling compared to LPBF 316L due to prolonged incubation. Energy Dispersive X-ray Spectroscopy (EDS) mapping indicates Ni and Si segregation at void surfaces due to radiation-induced segregation. At 300 °C, where voids are absent, the distribution of dislocation loops and stacking fault tetrahedra appears to be uniform. Dislocation cell structures mostly disappeared by 2 dpa for all conditions in this work. M 23 C 6 carbides were observed in LPBF 316H at 600 °C as early as 0.2 dpa, but not in LPBF 316L. Nanoindentation was performed to obtain the hardness of irradiated materials. In conclusion, this work illustrated the influence of additive manufacturing processes on microstructure evolution under irradiation, revealing the differences as well as the similarities as compared with wrought 316 SS, and the AM-related phenomenon that can potentially occur under neutron irradiation in nuclear reactors.

36 - MATERIALS SCIENCE↗

Comparison of Short-Term Oxidation Behavior of Model and Commercial Chromia-Forming Ferritic Stainless Steels in Air with Water Vapor

A high-purity Fe-20Cr and commercial type 430 ferritic stainless steel were exposed at 700 and 800 C in dry air and air with 10% water vapor (wet air) and characterized by SEM, XRD, STEM, SIMS, and EPMA. The Fe-20Cr alloy formed a fast growing Fe-rich oxide scale at 700 C in wet air after 24 h exposure, but formed a thin chromia scale at 700 C in dry air and at 800 C in both dry air and wet air. In contrast, thin spinel + chromia base scales with a discontinuous silica subscale were formed on 430 stainless steel under all conditions studied. Extensive void formation was observed at the alloy-oxide interface for the Fe-20Cr in both dry and wet conditions, but not for the 430 stainless steel. The Fe-20Cr alloy was found to exhibit a greater relative extent of subsurface Cr depletion than the 430 stainless steel, despite the former's higher Cr content. Depletion of Cr in the Fe-20Cr after 24 h exposure was also greater at 700 C than 800 C. The relative differences in oxidation behavior are discussed in terms of the coarse alloy grain size of the high-purity Fe-20Cr material, and the effects of Mn, Si, and C on the oxide scale formed on the 430 stainless steel.

08 HYDROGEN↗

Relationship Between Microstructure and Marine Corrosion Resistance of Martensitic Stainless Steels: A Multiscale Approach

The electrochemical properties of martensitic stainless steels may depend on complex aspects of their microstructure. Three alloys were considered in this study: X30Cr13 (AISI 420), a martensitic stainless steel with a low content of alloying elements; X17CrNi16-2 (AISI 431), chosen for its strong resistance to corrosion; and X5CrNiCu15-5 (AISI 630), chosen for its good mechanical resistance. Voltammetry tests have shown the influence of carbon and chromium content on corrosion resistance. Resistance to pitting appears equivalent for the both. However, heterogeneous corrosion, in relation to δ-ferrite precipitation and chromium carbides at the lath boundaries, appears in the case of X17CrNi16-2. Conversely, non-preferential corrosion occurs in the case of the X5CrNiCu15-5, and a superior passive film stability during immersion in artificial seawater. This counterbalance negative effect of the microstructure. Thus, it achieves an equivalent “macroscopically” corrosion behavior between the two steels.

36 MATERIALS SCIENCE↗

Experimental Investigation of Friction and Wear Behavior of 304L Stainless Steel Sliding Against Different Counterface in Dry Contact

In this study, friction and wear behavior of 304L stainless steel sliding against different ball counterface under dry contact was investigated. Tests were conducted using a ball-on-flat contact configuration in reciprocating sliding with 440C stainless steel, Al alloy (2017) and bronze ball counterfaces under different loads. Detailed surface analysis was also done using 3-D profilometry technique and optical microscopy in order to determine wear mechanism and dimension. All the pairs exhibited initial rapid increase in coefficient of friction after which a variety of friction behavior, depending on the ball counterface, was observed. The flat and the ball counterface in 304L stainless steel-440C stainless steel pair showed wear that was proportional to applied load. In both 304L stainless steel-Al alloy (2017) and 304L stainless steel-bronze pairs, ball samples showed severe wear that was proportional to the applied load while material transfer from the different balls occurred in the flat. The study concluded that friction and wear were not material properties but a kind of responses that characterize a pair of surfaces in contact undergoing relative motion.

Olofinjana, Bolutife↗

Accelerated corrosion of stainless steel in thiocyanate-containing solutions

It is known that reduced sulfur compounds (such as thiocyanate and thiosulfate) can accelerate active corrosion of austenitic stainless steel in acid solutions, but before we started this project the mechanism of acceleration was largely unclear. This work combined electrochemical measurements and analysis using scanning electron microscopy (SEM) and X-ray photo-electron spectroscopy (XPS), which provided a comprehensive understanding of the catalytic effect of reduced sulfur species on the active corrosion of stainless steel. Both the behavior of the pure elements and the steel were studied and the work focused on the interaction between the pure elements of the steel, which is the least understood area. Upon completion of this work, several aspects are now much clearer. The main results from this work can be summarized as follows: The presence of low concentrations (around 0.1 mM) of thiocyanate or tetrathionate in dilute sulfuric acid greatly accelerates the anodic dissolution of chromium and nickel, but has an even stronger effect on stainless steels (iron-chromium-nickel alloys). Electrochemical measurements and surface analyses are in agreement with the suggestion that accelerated dissolution really results from suppressed passivation. Even well below the passivation potential, the electrochemical signature of passivation is evident in the electrode impedance; the electrode impedance shows clearly that this pre-passivation is suppressed in the presence of thiocyanate. For the stainless steels, remarkable changes in the morphology of the corroded metal surface and in the surface concentration of chromium support the suggestion that pre-passivation of stainless steels is suppressed because dissolution of chromium is accelerated. Surface analysis confirmed that adsorbed sulfur / sulfide forms on the metal surfaces upon exposure to solutions containing thiocyanate or thiosulfate. For pure nickel, and steels containing nickel (and residual copper), bulk sulfide (visible as a black corrosion product) forms during anodic dissolution. The sulfide is electronically conductive, and gives an increase of several orders of magnitude in the electrode capacitance; the sulfide also causes anodic activation to persist after the pure metals and steels were removed from the thiocyanate-containing electrolyte and transferred to a thiocyanate-free electrolyte. The main practical implications of this work are that low concentrations of reduced sulfur compounds strongly affect anodic dissolution of stainless steels, and that selecting steels with elevated concentrations of chromium, nickel or molybdenum would serve to limit the anodic dissolution rate in the presence of reduced sulfur compounds.

36 MATERIALS SCIENCE↗

Corrosion Kinetics of Stainless Steel by Hydrogen Measurement under Deep Geological Repository Condition - 16047

Spent fuel assemblies consisting of stainless steels are expected to be disposed of in a deep underground repository. The radionuclides release and gas generation from activated metallic wastes in a disposal system will be controlled by the corrosion reaction. Most studies on stainless steel corrosion have been investigated under corrosion rates around several μm.a{sup -1}. A recent study has revealed that the corrosion rate of stainless steel is extremely slow-less than nm.a{sup -1} at 303 K. In the present study, corrosion kinetics at different temperatures up to 353 K were evaluated from the oxidation reaction by hydrogen gas measurement using 18Cr-8Ni austenitic stainless steel in a deoxygenated glass ampoule filled with a dilute NaOH solution of pH 12.5 for 24 months. Uniform corrosion and a reaction of 3Fe + 4H{sub 2}O → Fe{sub 3}O{sub 4} + 4H{sub 2} were assumed. After 24 months, the corrosion rates, which decreased with time but increased with rising temperature, were on average 7.80 x 10{sup -4}, 2.65 x 10{sup -3}, and 7.62 x 10{sup -3} μm.a{sup -1} at 303 K, 323 K, and 353 K, respectively. The corrosion kinetics were found to follow a parabolic rate law, which suggests the corrosion process is under diffusion control. The activation energy evaluated by the Arrhenius relationship of the parabolic rate constants has been determined to be 82.5 ± 6.2 kJ/mol, which corresponds to the values at high temperatures down to 423 K. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Effect of surface polishing and vacuum firing on electron stimulated desorption from 316LN stainless steel

The reduction of thermal outgassing from stainless steel by surface polishing or vacuum firing is well-known in vacuum technology, and the consequent use of both techniques allows an even further reduction of outgassing. The aim of this study was to identify the effectiveness of surface polishing and vacuum firing for reducing electron-stimulated desorption (ESD) from 316LN stainless steel, which is a frequently used material for particle accelerator vacuum chambers and components. It was found that, unlike for thermal outgassing, surface polishing does not reduce the ESD yield and may even increase it, while vacuum firing of nonpolished sample reduces only the H{sub 2} ESD yield by a factor 2.

36 MATERIALS SCIENCE↗

The High-Temperature Mechanical Properties of EN 1.4509 Stainless Steel Cast Using Investment Casting

The high-temperature (600-900 °C) mechanical properties of EN 1.4509 stainless steel made by investment casting were studied by changing the Nb content based on this stainless steel composition standard. The results indicate that with an increase in tensile temperature, the high-temperature strength shows a downward trend and the high-temperature plasticity increases. The results also indicate that with an increase in Nb content, the high-temperature strength rises continually and the high-temperature plasticity decreases; for example, the tensile strengths at 900 °C of Steel A, Steel B and Steel C are 21, 25 and 31 MPa, respectively, and the yield strengths are 15, 20 and 22 MPa, respectively, and the elongations are 97.7, 85.3 and 73.7%, respectively. The high-temperature tensile strength of the investment casting EN 1.4509 stainless steel sample is closely related to the bulk (Ti, Nb) (C, N) and the Laves phase (Fe{sub 2}Nb) at the ferritic grain boundaries and in the ferritic grains. These are the main factors for improvement in the high-temperature strength of the tested steels; additionally, the coarse ferritic grains also play a certain role in improving the mechanical properties. The Nb content of the investment casting EN 1.4509 stainless steel can be reduced to 0.25 wt.%, and at this content, a combination of good high-temperature mechanical properties and higher room-temperature plasticity is obtained.

36 MATERIALS SCIENCE↗