Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS CYCLE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Blade Mistuning Analysis for Boundary Layer Inlet Flow Distortion-Tolerant Fan Blades

NASA Glenn Research Center has tested the BLI2DTF propulsor including the fan rotor. BLI2DTF stands for Boundary Layer Ingesting Inlet/Distortion-Tolerant Fan. A comparison of the vibratory response between analysis results and experimental wind tunnel test results yielded reasonable agreement, yet some differences were noted. Blade mistuning effects have been identified as a potential cause for these differences. A tuned forced response analysis in a turbomachinery engine rotor system assumes that all of the blades are identical, so that the natural frequencies of individual blades are the same. In contrast to this assumption, the wind tunnel tests of the BLI2DTF rotor system revealed that the individual blade response frequencies varied. These variations in individual blade frequencies may be attributed to blade mistuning due to potential differences in the structural and material properties of individual blades. For an understanding of these variations, it is necessary to analyze the influence of blade mistuning on the BLI2DTF rotor system, which will provide a more precise assessment of its vibratory stresses and high cycle fatigue life. The purpose of the study was to investigate the influence of blade mistuning on the dynamic characteristics of this rotor system. At the same fan operation condition, a comparative forced response analysis was performed for both tuned and mistuned BLI2DTF rotor systems. A comparison of the results from these analyses found that the mistuning effects on the present BLI2DTF rotor system are notable. As a result, fan blade mistuning is to be considered a contributor to the levels of vibratory dynamic stresses observed during the wind tunnel experiment.

Blade mistuning↗
NASA NTRS1941

Effect of alternately high and low repeated stresses upon the fatigue strength of 25S-T aluminum alloy

Fatigue tests were made on one lot of 3/4 inch diameter rolled-and-drawn 25S-T aluminum-alloy rod normal in composition and tensile properties. The specimens were tested at 3500 cycles per second in a rotating-beam fatigue test machine. Tests were made for three ratios (20:1, 50:1, and 200:1) of the number of cycles applied at low stress to the number applied at high stress. In general, failure occurred when the number of cycles at either the low or the high stress approached the ordinary fatigue curve for the material, regardless of the sequence in which the stresses were applied.

Stickley, G W↗
NASA NTRS1977

A Directionally Solidified Iron-chromium-aluminum-tantalum Carbide Eutectic Alloy

A eutectic alloy, Fe-13.6CR-3.7Al+9TaC, was directionally solidified in a high gradient furnace, producing a microstructure of alined TaC fibers in an oxidation resistant alpha-iron matrix. Tensile and stress rupture properties, thermal cycling resistance, and microstructures were evaluated. The alloy displays at 1000 C an ultimate tensile strength of 58 MPa and a 100-hour rupture life at a stress of 21 MPa. Thermal cycling to 1100 C induces faceting in the TaC fibers.

Harf, F. H.↗
NASA NTRS1971

Generation of Finite Life Distributional Goodman Diagrams for Reliability Prediction

The methodology of developing finite life distributional Goodman diagrams and surfaces is described for presenting allowable combinations of alternating stress and mean stress to the design engineer. The combined stress condition is that of an alternating bending stress and a constant shear stress. The finite life Goodman diagrams and surfaces are created from strength distributions developed at various ratios of alternating to mean stress at particular cycle life values. The conclusions indicate that the Von Mises-Hencky ellipse, for cycle life values above 1000 cycles, is an adequate model of the finite life Goodman diagram. In addition, suggestions are made which reduce the number of experimental data points required in a fatigue data acquisition program.

Kececioglu, D.↗
NASA NTRS1973

High gas velocity burner tests on silicon carbide and silicon nitride at 1200 C

Specimens of silicon carbide and silicon nitride were exposed to a Mach one gas velocity burner simulating a turbine engine environment. Cyclic tests up to 100 hour duration were conducted at specimen temperatures of 1200 C. A specimen geometry was used that develops thermal stresses during thermal cycling in a manner similar to blades and vanes of a gas turbine engine. Materials were compared on a basis of weight change, dimensional reductions, metallography, fluorescent penetrant inspection, X-ray diffraction analyses, failure mode, and general appearance. One hot pressed SiC, one reaction sintered SiC, and three hot pressed Si3N4 specimens survived the program goal of 100 one-hour cycle exposures. Of the materials that failed to meet the program goal, thermal fatigue was identified as the exclusive failure mode.

Sanders, W. A.↗
NASA NTRS1974

High gas velocity burner tests on silicon carbide and silicon nitride at 1200 C

Ten SiC materials and five Si3N4 materials were exposed in a Mach 1-gas-velocity burner simulating a gas-turbine engine environment. All materials studied are commercially available. Cyclic tests up to 100 hours' duration were conducted at specimen temperatures of 1200 C. A specimen geometry was used that develops thermal stresses during thermal cycling in a manner similar to blades and vanes of a gas turbine engine. Materials were compared on a basis of weight change, dimensional reductions, metallography, fluorescent-penetrant inspection, X-ray diffraction analyses, failure mode, and general appearance. One hot-pressed SiC, one reaction-sintered SiC, and three hot-pressed Si3N4 materials survived the program goal of 100 one-hour cycles of exposures. Of the materials that failed to meet the program goal, thermal fatigue was identified as the exclusive failure mode.

Sanders, W. A.↗
NASA NTRS1981

Room temperature shear properties of the strain isolator pad for the shuttle thermal protection system

Tests were conducted at room temperature to determine the shear properties of the strain isolator pad (SIP) material used in the thermal protection system of the space shuttle. Tests were conducted on both the .23 cm and .41 cm thick SIP material in the virgin state and after fifty fully reversed shear cycles. The shear stress displacement relationships are highly nonlinear, exhibit large hysteresis effects, are dependent on material orientation, and have a large low modulus region near the zero stress level where small changes in stress can result in large displacements. The values at the higher stress levels generally increase with normal and shear force load conditioning. Normal forces applied during the shear tests reduces the low modulus region for the material. Shear test techniques which restrict the normal movement of the material give erroneous stress displacement results. However, small normal forces do not significantly effect the shear modulus for a given shear stress. Poisson's ratio values for the material are within the range of values for many common materials. The values are not constant but vary as a function of the stress level and the previous stress history of the material. Ultimate shear strengths of the .23 cm thick SIP are significantly higher than those obtained for the .41 cm thick SIP.

Sawyer, J. W.↗
NASA NTRS1980

Internal coating of air-cooled gas turbine blades

Four modified aluminide coatings were developed for IN-792 + Hf alloy using a powder pack method applicable to internal surfaces of air-cooled blades. The coating compositions are Ni-19Al-1Cb, Ni-19Al-3Cb, Ni-17Al-20Cr, and Ni-12Al-20Cr. Cyclic burner rig hot corrosion (900 C) and oxidation (1050 C) tests indicated that Ni-Al-Cb coatings provided better overall resistance than Ni-Al-Cr coatings. Tensile properties of Ni-19Al-1Cb and Ni-12Al-20Cr coated test bars were fully retained at room temperature and 649 C. Stress rupture results exhibited wide scatter around uncoated IN-792 baseline, especially at high stress levels. High cycle fatigue lives of Ni-19Al-1Cb and Ni-12Al-20Cr coated bars (as well as RT-22B coated IN-792) suffered approximately 30 percent decrease at 649 C. Since all test bars were fully heat treated after coating, the effects of coating/processing on IN-792 alloy were not recoverable. Internally coated Ni-19Al-1Cb, Ni-19Al-3Cb, and Ni-12Al-20Cr blades were included in 500-hour endurance engine test and the results were similar to those obtained in burner rig oxidation testing.

Hsu, L. L.↗
NASA NTRS1984

Performance of thermal barrier coatings in high heat flux environments

Thermal barrier coatings were exposed to the high temperature and high heat flux produced by a 30 kW plasma torch. Analysis of the specimen heating rates indicates that the temperature drop across the thickness of the 0.038 cm ceramic layer was about 1100 C after 0.5 sec in the flame. An as-sprayed ZrO2-8%Y2O3 specimens survived 3000 of the 0.5 sec cycles with failing. Surface spalling was observed when 2.5 sec cycles were employed but this was attributed to uneven heating caused by surface roughness. This surface spalling was prevented by smoothing the surface with silicon carbide paper or by laser glazing. A coated specimen with no surface modification but which was heat treated in argon also did not surface spall. Heat treatment in air led to spalling in as early as 2 cycle from heating stresses. Failures at edges were investigated and shown to be a minor source of concern. Ceramic coatings formed from ZrO2-12%Y2O3 or ZrO2-20%Y2O3 were shown to be unsuited for use under the high heat flux conditions of this study.

Miller, R. A.↗
NASA NTRS1984

Performance of thermal barrier coatings in high heat flux environments

Thermal barrier coatings were exposed to the high temperature and high heat flux produced by a 30 kW plasma torch. Analysis of the specimen heating rates indicates that the temperature drop across the thickness of the 0.038 cm ceramic layer was about 1100 C after 0.5 sec in the flame. An as-sprayed ZrO2-8 percent Y2O3 specimens survived 3000 of the 0.5 sec cycles with falling. Surface spalling was observed when 2.5 sec cycles were employed but this was attributed to uneven heating caused by surface roughness. This surface spalling was prevented by smoothing the surface with silicon carbide paper or by laser glazing. A coated specimen with no surface modification but which was heat treated in argon also did not surface spall. Heat treatment in air led to spalling in as early as 1 cycle from heating stresses. Failures at edges were investigated and shown to be a minor source of concern. Ceramic coatings formed from ZrO2-12 percent Y2O3 or ZrO2-2O percent Y2O3 were shown to be unsuited for use under the high heat flux conditions of this study.

Miller, R. A.↗
NASA NTRS1984

Performance of thermal barrier coatings in high heat flux environments

Thermal barrier coatings were exposed to the high temperature and high heat flux produced by a 30 kW plasma torch. Analysis of the specimen heating rates indicates that the temperature drop across the thickness of the 0.038 cm ceramic layer was about 1100 C after 0.5 sec in the flame. An as-sprayed ZrO2-8 percent Y203 specimens survived 3000 of the 0.5 sec cycles with failing. Surface spalling was observed when 2.5 sec cycles were employed but this was attributed to uneven heating caused by surface roughness. This surface spalling was prevented by smoothing the surface with silicon carbide paper or by laser glazing. A coated specimen with no surface modification but which was heat treated in argon also did not surface spall. Heat treatment in air led to spalling in as early as 2 cycle from heating stresses. Failures at edges were investigated and shown to be a minor source of concern. Ceramic coatings formed from ZrO2-12 percent Y2O3 or ZrO2-20 percent Y2O3 were shown to be unsuited for use under the high heat flux conditions of this study.

Miller, R. A.↗
NASA NTRS1987

Distributed computer system enhances productivity for SRB joint optimization

The Programming System for Structural Synthesis software package, which couples structural analysis and optimization, has been distributed over a network of work stations for use in Space Shuttle Solid Rocket Booster joint redesign optimization. Finite difference computing techniques were applied to the optimization gradients in parallel execution, allowing several work stations to simultaneously contribute to the problem's solution. An optimal joint shape was obtained which achieves minimum weight while keeping the gap between joints well closed and limiting structural stresses. The optimization cycle was reduced from two hours to one-half hour.

Rogers, James L., Jr.↗
NASA NTRS1985

Creep-fatigue behavior of NiCoCrAlY coated PWA 1480

This study of high-temperature fatigue and creep-fatigue behavior is part of a program to identify the basic features of the effects of temperature, creep, fatigue, and environment on the behavior of a single crystal superalloy, a bulk coating alloy, and a coated alloy system. A system was selected which has had considerable production experience: the Ni-base superalloy, PWA 1480, and the NiCoCrAlY coating, PWA 276. Isothermal behavior was studied first. A series of fatigue and creep fatigue tests of the types commonly designated as pp, cp, pc and cc were conducted. These tests were conducted at various constant total strain ranges. The creep-fatigue cycles employed constant stress dwells at the maximum and/or minimum load. Test results are given.

Miner, R. V.↗
NASA NTRS1952

Effects of Cyclic Loading on Mechanical Behavior of 24S-T4 and 75S-T6 Aluminum Alloys and SAE 4130 Steel

An investigation was conducted to determine the effects of cyclic loading on the mechanical behavior of 24S-T4 and 75S-T6 aluminum alloys and SAE 4130 steel. Specimens of the three materials were subjected to various numbers of prior fatigue cycles both below and above the fatigue limits. Special slow-bend tests were employed to show the effects of prior cycles of fatigue stressing on the transition temperature to brittle fracture for SAE 4130 steel and on the energy-absorption capacity of the aluminum alloys. Micrographic studies were made to observe and measure crack formation and propagation and additional special tests were conducted to supplement the results of the slow-bend tests. These included Charpy impact tests, mirohardness surveys, tension tests, and fretting-corrosion studies.

STEELS↗