Search NASA⌕ Search

SEARCH · Search NASA

Results for “Single point correction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

A correlated ab initio study of the A2 pi <-- X2 sigma+ transition in MgCCH

The A2 pi <-- X2 sigma+ transition in MgCCH was studied with correlation consistent basis sets and single- and multireference correlation methods. The A2 pi excited state was characterized in detail; the x2 sigma+ ground state has been described elsewhere recently. The estimated complete basis set (CBS) limits for valence correlation, including zero-point energy corrections, are 22668, 23191, and 22795 for the RCCSD(T), MRCI, and MRCI + Q methods, respectively. A core-valence correction of +162 cm-1 shifts the RCCSD(T) value to 22830 cm-1, in good agreement with the experimental result of 22807 cm-1.

Non-NASA Center↗

Errata Sheet for the Closure Report for Corrective Action Unit 538: Spill Sites, Nevada Test Site, Nevada with ROTC-1, Revision 0

This Erratum is being issued to DOE/NV--1185 ROTC-1 for the CAU 538 Closure Report to correct three items. The original ROTC which was issued on November 30, 2011 corrected the Use Restriction for CAS 12-29-06 to remove a coordinate point from the Use Restriction. However, the ROTC contained three errors as follows: 1. The number of digits after the decimal place on the UR form was one while the map displayed two digits after the decimal place. The UR form and map were aligned as part of this Erratum so that only a single digit was shown after the decimal place. 2. On the figure (Figure 1) included with the UR form issued as part of ROTC-1, CAU 538 was incorrectly called out as CAU 583. This error was corrected as part of this Erratum. 3. The coordinates on the UR form were developed from NAD 27 while the coordinate system stated on the form was UTM, Zone 11, NAD 83 meters. The coordinates were corrected on the UR form, developed as part of this Erratum, to reflect the UTM, Zone 11, NAD 83 meters system.

54 ENVIRONMENTAL SCIENCES↗

Mitigating challenges in aberration-corrected electron-beam lithography on electron-opaque substrates

Aberration-corrected electron-beam lithography (AC-EBL) using ultra-thin electron transparent membranes has achieved single-digit nanometer resolution in two widely used electron-beam resists: poly (methyl methacrylate) (PMMA) and hydrogen silsesquioxane. On the other hand, AC-EBL implementation on thick, electron-opaque substrates is appealing for conventional top-down fabrication of quantum devices with nanometer-scale features. To investigate the performance of AC-EBL on thick substrates, we measured the lithographic point spread function of a 200 keV aberration-corrected scanning transmission electron microscope by defining both positive and negative patterns in PMMA thin films, spin-cast on thick SiO 2 /Si substrates. We present the problems encountered during pre-exposure beam focusing and discuss methods to overcome them. In addition, applying some of these methods using commercial 50 nm thick SiN X membranes with thick Si support frames, we printed arrays of holes in PMMA with pitches around 26 nm on SiN X /Si substrates with increasing Si thickness. Here, our results show that proximity effects from even 50 nm thick SiN X membranes limit hole arrays to 20 nm pitch; however, down to this limit, the effect of the substrate thickness on the pattern quality is minimal. These results highlight the need for novel resists less susceptible to proximity effects, or resists which can be used directly, after development, as the dielectric material in periodic gates in 2D quantum devices.

2D quantum devices↗

High-level theoretical characterization of the vinoxy radical ( • CH 2 CHO) + O 2 reaction

Numerous processes in atmospheric and combustion chemistry produce the vinoxy radical ( • CH 2 CHO). To understand the fate of this radical and to provide reliable energies needed for kinetic modeling of such processes, we have examined its reaction with O 2 using highly reliable theoretical methods. Utilizing the focal point approach, the energetics of this reaction and subsequent reactions were obtained using coupled-cluster theory with single, double, and perturbative triple excitations [CCSD(T)] extrapolated to the complete basis set limit. These extrapolated energies were appended with several corrections including a treatment of full triples and connected quadruple excitations, i.e., CCSDT(Q). In addition, this study models the initial vinoxy radical + O 2 reaction for the first time with multireference methods. We predict a barrier for this reaction of approximately 0.4 kcal mol –1 . This result agrees with experimental findings but is in disagreement with previous theoretical studies. The vinoxy radical + O 2 reaction produces a 2-oxoethylperoxy radical which can undergo a number of unimolecular reactions. Abstraction of a β-hydrogen (a 1,4-hydrogen shift) and dissociation back to reactants are predicted to be competitive to each other due to their similar barriers of 21.2 and 22.3 kcal mol –1 , respectively. The minimum-energy β-hydrogen abstraction pathway produces a hydroperoxy radical (QOOH) that eventually decomposes to formaldehyde, CO, and • OH. Two other unimolecular reactions of the peroxy radical are α-hydrogen abstraction (38.7 kcal mol –1 barrier) and HO 2 • elimination (43.5 kcal mol –1 barrier). Furthermore, these pathways lead to glyoxal + • OH and ketene + HO 2 • formation, respectively, but they are expected to be uncompetitive due to their high barriers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Neutral-Point Expansion of the Ideal Magnetosphere

The idealized model of the geomagnetic field-solar wind interaction yields a singular (neutral) point on the magnetopause at which the magnetic field vanishes. If we expand the fields in a power series around this point, including quadratic terms, we can derive an approximate equation of the magnetopause in a small neighborhood of the neutral point which is consistent with the idealized boundary conditions to fourth order. We then consider the additional pressure due to multiple reflections of particles in this neighborhood and show that less than a 4 per cent correction to the single-reflection pressure condition is necessary.

MATHEMATICAL MODEL↗

FPGA-Based, Self-Checking, Fault-Tolerant Computers

A proposed computer architecture would exploit the capabilities of commercially available field-programmable gate arrays (FPGAs) to enable computers to detect and recover from bit errors. The main purpose of the proposed architecture is to enable fault-tolerant computing in the presence of single-event upsets (SEUs). [An SEU is a spurious bit flip (also called a soft error) caused by a single impact of ionizing radiation.] The architecture would also enable recovery from some soft errors caused by electrical transients and, to some extent, from intermittent and permanent (hard) errors caused by aging of electronic components. A typical FPGA of the current generation contains one or more complete processor cores, memories, and highspeed serial input/output (I/O) channels, making it possible to shrink a board-level processor node to a single integrated-circuit chip. Custom, highly efficient microcontrollers, general-purpose computers, custom I/O processors, and signal processors can be rapidly and efficiently implemented by use of FPGAs. Unfortunately, FPGAs are susceptible to SEUs. Prior efforts to mitigate the effects of SEUs have yielded solutions that degrade performance of the system and require support from external hardware and software. In comparison with other fault-tolerant- computing architectures (e.g., triple modular redundancy), the proposed architecture could be implemented with less circuitry and lower power demand. Moreover, the fault-tolerant computing functions would require only minimal support from circuitry outside the central processing units (CPUs) of computers, would not require any software support, and would be largely transparent to software and to other computer hardware. There would be two types of modules: a self-checking processor module and a memory system (see figure). The self-checking processor module would be implemented on a single FPGA and would be capable of detecting its own internal errors. It would contain two CPUs executing identical programs in lock step, with comparison of their outputs to detect errors. It would also contain various cache local memory circuits, communication circuits, and configurable special-purpose processors that would use self-checking checkers. (The basic principle of the self-checking checker method is to utilize logic circuitry that generates error signals whenever there is an error in either the checker or the circuit being checked.) The memory system would comprise a main memory and a hardware-controlled check-pointing system (CPS) based on a buffer memory denoted the recovery cache. The main memory would contain random-access memory (RAM) chips and FPGAs that would, in addition to everything else, implement double-error-detecting and single-error-correcting memory functions to enable recovery from single-bit errors.

Some, Raphael↗

PLATFORM DEFORMATION PHASE CORRECTION FOR THE AMiBA-13 COPLANAR INTERFEROMETER

We present a new way to solve the platform deformation problem of coplanar interferometers. The platform of a coplanar interferometer can be deformed due to driving forces and gravity. A deformed platform will induce extra components into the geometric delay of each baseline and change the phases of observed visibilities. The reconstructed images will also be diluted due to the errors of the phases. The platform deformations of The Yuan-Tseh Lee Array for Microwave Background Anisotropy (AMiBA) were modeled based on photogrammetry data with about 20 mount pointing positions. We then used the differential optical pointing error between two optical telescopes to fit the model parameters in the entire horizontal coordinate space. With the platform deformation model, we can predict the errors of the geometric phase delays due to platform deformation with a given azimuth and elevation of the targets and calibrators. After correcting the phases of the radio point sources in the AMiBA interferometric data, we recover 50%-70% flux loss due to phase errors. This allows us to restore more than 90% of a source flux. The method outlined in this work is not only applicable to the correction of deformation for other coplanar telescopes but also to single-dish telescopes with deformation problems. This work also forms the basis of the upcoming science results of AMiBA-13.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Spin-free formulation of the multireference driven similarity renormalization group: A benchmark study of first-row diatomic molecules and spin-crossover energetics

We report a spin-free formulation of the multireference (MR) driven similarity renormalization group (DSRG) based on the ensemble normal ordering of Mukherjee and Kutzelnigg (1997). This ensemble averages over all microstates of a given total spin quantum number, and therefore, it is invariant with respect to SU(2) transformations. As such, all equations may be reformulated in terms of spin-free quantities and they closely resemble those of spin-adapted closed-shell coupled cluster (CC) theory. The current implementation is used to assess the accuracy of various truncated MR-DSRG methods (perturbation theory up to third order and iterative methods with single and double excitations) in computing the constants of 33 first-row diatomic molecules. The accuracy trends for these first-row diatomics are consistent with our previous benchmark on a small subset of closed-shell diatomic molecules. We then present the first MR-DSRG application on transition-metal complexes by computing the spin splittings of the [Fe(H 2 O) 6 ] 2+ and [Fe(NH 3 ) 6 ] 2+ molecules. A focal point analysis (FPA) shows that third-order perturbative corrections are essential to achieve reasonably converged energetics. The FPA based on the linearized MR-DSRG theory with one- and two-body operators and up to a quintuple- ζ basis set predicts the spin splittings of [Fe(H 2 O) 6 ] 2+ and [Fe(NH 3 ) 6 ] 2+ to be –35.7 and –17.1 kcal mol –1 , respectively, showing good agreement with the results of local CC theory with singles, doubles, and perturbative triples.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Noise correction of turbulent spectra obtained from Acoustic Doppler Velocimeters

Accurately estimated auto-spectral density functions are essential for characterization of turbulent flows, and they also have applications in computational fluid dynamics modeling, site and inflow characterization for hydrokinetic turbines, and inflow turbulence generation. The Acoustic Doppler Velocimeter (ADV) provides single-point temporally resolved data, that are used to characterize turbulent flows in rivers, seas, and oceans. However, ADV data are susceptible to contamination from various sources, including instrument noise, which is the intrinsic limit to the accuracy of acoustic velocity measurements. Due to the presence of instrument noise, the spectra obtained are altered at high frequencies. The focus of this study is to develop a robust and effective method for accurately estimating auto-spectral density functions from ADV data by reducing or removing the spectral contribution derived from instrument noise. For this purpose, the “Noise Auto-Correlation” (NAC) approach was developed, which exploits the correlation properties of instrument noise to identify and remove its contribution from spectra. The spectra estimated using the NAC approach exhibit increased fidelity and a slope of -5/3 in the inertial range, which is typically observed for turbulent flows. Finally, this study also compares the effectiveness of low-pass Gaussian filters in removing instrument noise with that of the NAC approach. For the data used in this study, both the NAC and Gaussian filter approaches are observed to be capable of removing instrument noise at higher frequencies from the spectra. However, the NAC results are closer to the expected frequency power of -5/3 in the inertial sub-range.

Acoustic Doppler Velocimeter↗

Pyrolysis of the Simplest Carbohydrate, Glycolaldehyde (CHO-CH 2 OH), and Glyoxal in a Heated Microreactor

Both glycolaldehyde and glyoxal were pyrolyzed in a set of flash-pyrolysis microreactors. The pyrolysis products resulting from CHO-CH 2 OH and HCO-CHO were detected and identified by vacuum ultraviolet (VUV) photoionization mass spectrometry. Complementary product identification was provided by argon matrix infrared absorption spectroscopy. Pyrolysis pressures in the microreactor were about 100 Torr, and contact times with the microreactors were roughly 100 μs. At 1200 K, the products of glycolaldehyde pyrolysis are H atoms, CO, CH 2 =O, CH 2 =C=O, and HCO-CHO. Thermal decomposition of HCO-CHO was studied with pulsed 118.2 nm photoionization mass spectrometry and matrix infrared absorption. Under these conditions, glyoxal undergoes pyrolysis to H atoms and CO. Tunable VUV photoionization mass spectrometry provides a lower bound for the ionization energy IE (CHO-CH 2 OH) ≥ 9.95 ± 0.05 eV. The gas-phase heat of formation of glycolaldehyde was established by a sequence of calorimetric experiments. The experimental result is Δ f H 298 (CHO-CH 2 OH) = -75.8 ± 1.3 kcal mol -1 . Fully ab initio , coupled cluster calculations predict Δ f H 0 (CHO-CH 2 OH) of -73.1 ± 0.5 kcal mol -1 and Δ f H 298 (CHO-CH 2 OH) of -76.1 ± 0.5 kcal mol -1 . The coupled-cluster singles doubles and noniterative triples correction calculations also lead to a revision of the geometry of CHO-CH 2 OH. We have found that the O-H bond length differs substantially from earlier experimental estimates, due to unusual zero-point contributions to the moments of inertia.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Analysis and Review of NASA Earth Science Metadata: How Automation Plays a Role

The Analysis and Review of the Common Metadata Repository (CMR ARC) Team reviews all EOSDIS metadata. The team’s objective is to achieve consistency, correctness, and completeness for all metadata records in the CMR, as well as improve the discoverability of NASA's Earth Science data within the CMR framework. This work is currently being completed at Marshall Space Flight Center. CMR makes a single discovery point possible for NASA's Earth Science data users. The CMR team, in collaboration with three other core metadata teams, contributes to the stewardship of NASA's Earth Science data through a process of continual curation and the ongoing development of the Unified Metadata Model (UMM). A key tool now used in the curation process, referred to as the NASA CMR Dashboard, is an online curation dashboard developed in collaboration with software development company, Element 84. This tool facilitates the review of Earth Science metadata records and subsequent stakeholder collaboration on the resolution of identified issues. A key capability of the new tool is a suite of automated compliance checks written in Python 3.6 that verify the integrity of various metadata elements across multiple standards.

Staton, Patrick↗

A Chromaticity Analysis and PSF Subtraction Techniques for SCExAO/CHARIS Data

We present an analysis of instrument performance using new observations taken with the Coronagraphic High Angular Resolution Imaging Spectrograph (CHARIS) instrument and the Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) system. In a correlation analysis of our data sets (which use the broadband mode covering the J band through the K band in a single spectrum), we find that chromaticity in the SCExAO/CHARIS system is generally worse than temporal stability. We also develop a point-spread function (PSF) subtraction pipeline optimized for the CHARIS broadband mode, including a forward modeling-based exoplanet algorithmic throughput correction scheme. We then present contrast curves using this newly developed pipeline. An analogous subtraction of the same data sets using only the H-band slices yields the same final contrasts as the full JHK sequences; this result is consistent with our chromaticity analysis, illustrating that PSF subtraction using spectral differential imaging (SDI) in this broadband mode is generally not more effective than SDI in the individual J, H, or K bands. In the future, the data processing framework and analysis developed in this paper will be important to consider for additional SCExAO/CHARIS broadband observations and other ExAO instruments which plan to implement a similar integral field spectrograph broadband mode.

Benjamin L. Gerard↗

Electromagnetic Transient Modeling of Large Data Centers for Grid-Level Studies

The magnitude and complexity of electricity usage patterns from large data centers are having significant impacts on the operation and dynamics of the power grid; grid operators and planners require a range of specialized data center models to properly evaluate these impacts and specify technical solutions as needed. Towards addressing this need, Pacific Northwest National Laboratory (PNNL) has developed a library of electromagnetic transient (EMT) models for grid-level studies of data centers called the data center model library (DML). This report describes how the DML was created and how it may properly be used. The models present in the DML are generic models; subject matter expertise and additional technical data are needed to modify these models before they can represent any real data center. However, they will significantly reduce the level of effort required to develop site-specific models and can serve as a common starting point to guide industry towards a more refined consensus. Most of the models within DML are dedicated to representing the power electronics interfaces commonly used in modern data centers, such as double-conversion uninterruptible power supplies and single-phase power factor correction converters. These models are intended for use in grid-level studies and are a simplified aggregation of many small components. That said, background material on the physical and electrical design of large data centers is provided as companion material so that users can be aware of many of the details which have been omitted or streamlined as a matter of practical necessity. Additionally, guidance on the application of EMT analysis for data center interconnection studies is provided, which aids users in identifying when the DML is necessary and what sort of additional model development may be necessary for conducting real-world studies.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Electromagnetic Transient Modeling of Large Data Centers for Grid-Level Studies: Beta Release

The magnitude and complexity of electricity usage patterns from large data centers are having significant impacts on the operation and dynamics of the power grid; grid operators and planners require a range of specialized data center models to properly evaluate these impacts and specify technical solutions as needed. Towards addressing this need, Pacific Northwest National Laboratory (PNNL) has developed a library of electromagnetic transient (EMT) models for grid-level studies of data centers called the data center model library (DML). This report describes how the DML was created and how it may properly be used. This report details the DML’s beta release, completed in July 2026. This is a revision and expansion of the alpha release, which was made available in January 2026 The models present in the DML are generic models; subject matter expertise and additional technical data are needed to modify these models before they can represent any real data center. However, they will significantly reduce the level of effort required to develop site-specific models and can serve as a common starting point to guide industry towards a more refined consensus. Most of the models within DML are dedicated to representing the power electronics interfaces commonly used in modern data centers, such as double-conversion uninterruptible power supplies and single-phase power factor correction converters. These models are intended for use in grid-level studies and are a simplified aggregation of many small components. That said, background material on the physical and electrical design of large data centers is provided as companion material so that users can be aware of many of the details which have been omitted or streamlined as a matter of practical necessity. Additionally, guidance on the application of EMT analysis for data center interconnection studies is provided, which aids users in identifying when the DML is necessary and what sort of additional model development may be necessary for conducting real-world studies.

electromagnetic transients↗

Custom Turnkey Time and Frequency Systems: A structured, expandable approach

Radiocode Clocks Ltd. have developed a Turnkey Time and Frequency Generation and Distribution, System strategy based upon a bus of three, 'core' signals from which any Time code, Pulse rate or Frequency can be produced. The heart of the system is a ruggedized 19 inch, 3U Single Eurocard chassis constructed from machined 10mm aluminum alloy plate and designed to meet stringent Military, Security and Telecommunications specifications. The chassis is fitted with an advanced multilayer backplane with separate ground planes for analog and digital signals ensuring no degradation of low noise frequency references in the proximity of high speed digital pulse transmissions. The system has been designed to be used in three possible configurations: 1) As a stand alone generation and distribution instrument; 2) As a primary distribution unit in a turnkey Time and Frequency system; and 3) As a secondary distribution unit at a remote location from the Turnkey Time and Frequency System providing regeneration of core signals and correction for transmission delays. When configured as a secondary distribution unit the system will continue to provide usable outputs when one, two or even all three of the 'core' signals are lost. The instrument's placement within a system as a possible single point of system failure has required the development of very high reliability translator, synthesizer, phase locked loop and distribution modules together with a comprehensive alarm and monitoring strategy.

Wright, David F.↗

Factors governing Yb magnetism in Yb{sub 0.95}PtIn{sub 2} and other MgCuAl{sub 2}-type structures

The ternary compound 'YbPtIn{sub 2}' has been synthesized and its crystal structure determined using single crystal X-ray diffraction techniques. The compound crystallizes in the MgCuAl{sub 2} structure, a ternary structure type often formed when rare earth metals, Group 10 transition metals, and indium are present in a 1:1:2 ratio. The unit cell is C-centered orthorhombic, space group Cmcm (no. 63) with lattice parameters of a=4.3410(1) A, b=10.3230(2) A, and c=7.8510(2) A. Evidence is found for a substantial non-stoichiometry on the Yb site, in contrast to the Pt and In sites which behave as expected, and it is believed that the stoichiometry of this compound is more properly described as Yb{sub 0.95}PtIn{sub 2}. Magnetic and resistivity measurements reveal that 'YbPtIn{sub 2}' is a weakly interacting, non-magnetic metal exclusively containing Yb{sup 2+}, and with a resistivity ({rho}) varying from 34 {mu}{Omega} cm at room temperature to a residual resistivity {rho}{sub 0} of 23 {mu}{Omega} cm at 1.8 K. Density functional theory calculations suggest that the observed diamagnetic Yb behavior is expected for this compound, but that certain substitutions on the Pt or In site could help stabilize magnetic Yb{sup 3+} and potentially induce heavy fermion behavior. - Graphical abstract: The crystal structure, magnetic behavior, and temperature-dependent resistivity of the new ternary compound Yb{sub 0.95}PtIn{sub 2.} Highlights: Black-Right-Pointing-Pointer Flux growth method used to produce Yb{sub 0.95}PtIn{sub 2} single crystals. Black-Right-Pointing-Pointer Found rare example of non-stoichiometry in a MgCuAl{sub 2}-type structure. Black-Right-Pointing-Pointer The resistivity and diamagnetic response of Yb{sub 0.95}PtIn{sub 2} were modeled. Black-Right-Pointing-Pointer DFT correctly predicts presence of Yb{sup 2+} in Yb{sub 0.95}PtIn{sub 2}. Black-Right-Pointing-Pointer COHP results suggest other MgCuAl{sub 2}-type indides that may contain paramagnetic Yb{sup 3+}.

36 MATERIALS SCIENCE↗

Using Principal Component Analysis (PCA) to Speed up Radiative Transfer (RT) Computations

Multiple scattering RT calculations time-consuming. Need a speed improvement of about 1000 (for OCO)! Solution: Make use of redundancies in spectra. Correlated-k (Lacis and Wang, Lacis and Oinas, Goody et al, Fu and Liou) Problem: Assume that spectral variation of atmospheric optical properties spatially correlated at all points along optical path. High accuracy (HI) and 2-stream (2S) calculations have high correlation. Single scattering (SS) computations highly scenario-dependent, but not time consuming. Perform SS and 2S calculations at every wavelength. Perform small number of HI computations. Need to compute correction factor B at every wavelength.

data sets↗

Challenge data set for macromolecular multi-microcrystallography

A synthetic data set demonstrating a particularly challenging case of indexing ambiguity in the context of radiation damage was generated. This set shall serve as a standard benchmark and reference point for the ongoing development of new methods and new approaches to robust structure solution when single-crystal methods are insufficient. Of the 100 short wedges of data, only the first 36 are currently necessary to solve the structure by `cheating', or using the correct reference structure as a guide. The total wall-clock time and number of crystals required to solve the structure without cheating is proposed as a metric for the efficacy and efficiency of a given multi-crystal automation pipeline.

36 MATERIALS SCIENCE↗