Search NASA⌕ Search

SEARCH · Search NASA

Results for “Strain calculation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Neutron Characterization of 3D Printed Gas Turbine Alloy With Internal Cooling Structure

The objective of this research work is to investigate the residual strains induced by the presence of a exit hole and internal hollow geometry present in a 3D printed IN718 similar to that seen in a gas turbine blade. The specimens were manufactured with an internal hollow structure that ended with an exit hole, and fabricated by direct metal laser sintering additive manufacturing technique. Using this technique, metal powder was melted by a laser source and rapidly cooled to form the part layer by layer. Rapid heating and cooling generate large thermal gradients and residual stresses in the 3D printed material. To be aligned with industry standards, specimens were heat-treated to relieve most of the residual stresses as well as to investigate whether IN718 still preserved a nonhomogeneous stress state after the thermal treatment. Roughness and microstructure analysis was performed to understand the heat-treated sample properties. To investigate the volumetric residual strain, the neutron diffraction technique was used with a definite neutron wavelength. Bragg’s law was used to determine lattice spacing. Interplanar lattice spacing and stress-free state lattice spacings were measured to calculate the strains. Residual strains were measured in the x and y direction to understand the impact of the presence of a exit hole and internal hollow geometry. The results of volumetric residual strain in the x and y directions showed no significant variations in the distribution of the strain due to the presence of a hollow structure as well as the exit hole. Overall, no significant stress concentration was observed in the heat treated sample. Sample geometry, instrumentation for neutron diffraction, and material properties are discussed in detail in this paper.

Raju, Nandhini↗

Towards Using Eshelby Calculations to Enhance Kinetic Model for Zirconium Hydride Precipitation

A C++ library (called Eshelby ) was implemented in fiscal year 2015 based upon the formulas documented in this report. The library implements a generalized version of Eshelby's inclusion problem. The library was written as a set of functions which can be called from another program; the principle intended use cases are kinetic models of precipitate formation in zirconium claddings where use of the Eshelby library provides needed elastic energy density calculations, as well as calculations of stress and strain in and around precipitates; it is intended that the library will be made open source. For isotropic inclusions in the form of oblate and prolate ellipsoids, the Eshelby library can be used for nearly any relevant/appropriate shape parameters to calculate strains, stresses and energy density at interior and exterior points. The Eshelby library uses a combination of analytical formulas and numerical routines making it very extensible. For example, the library can can easily be extended to include inclusions such as spheres since analytical expressions exist for the required elliptic integrals; similarly, general ellipsoids do not have analytical results for the required elliptic integrals but those integrals can be numerically evaluated and thus fit naturally into the Eshelby library. This report documents all formulas implemented in the Eshelby library and presents some demonstration calculations relevant to the intended application.

97 MATHEMATICS AND COMPUTING↗

Gas tungsten arc welding and friction stir welding of ultrafine grained AISI 304L stainless steel: Microstructural and mechanical behavior characterization

In the present study, an ultrafine grained (UFG) AISI 304L stainless steel with the average grain size of 650 nm was successfully welded by both gas tungsten arc welding (GTAW) and friction stir welding (FSW). GTAW was applied without any filler metal. FSW was also performed at a constant rotational speed of 630 rpm and different welding speeds from 20 to 80 mm/min. Microstructural characterization was carried out by High Resolution Scanning Electron Microscopy (HRSEM) with Electron Backscattered Diffraction (EBSD) and Transmission Electron Microscopy (TEM). Nanoindentation, microhardness measurements and tensile tests were also performed to study the mechanical properties of the base metal and weldments. The results showed that the solidification mode in the GTAW welded sample is FA (ferrite–austenite) type with the microstructure consisting of an austenite matrix embedded with lath type and skeletal type ferrite. The nugget zone microstructure in the FSW welded samples consisted of equiaxed dynamically recrystallized austenite grains with some amount of elongated delta ferrite. Sigma phase precipitates were formed in the region ahead the rotating tool during the heating cycle of FSW, which were finally fragmented into nanometric particles and distributed in the weld nugget. Also there is a high possibility that the existing delta ferrite in the microstructure rapidly transforms into sigma phase particles during the short thermal cycle of FSW. These suggest that high strain and deformation during FSW can promote sigma phase formation. The final austenite grain size in the nugget zone was found to decrease with increasing Zener–Hollomon parameter, which was obtained quantitatively by measuring the peak temperature, calculating the strain rate during FSW and exact examination of hot deformation activation energy by considering the actual grain size before the occurrence of dynamic recrystallization. Mechanical properties observations showed that the welding efficiency of the FSW welded sample is around 70%, which is more than 20% higher than the GTAW welded sample. - Highlights: • Microstructure and mechanical properties of UFG 304L stainless steel were studied during GTAW and FSW. • Sigma phase formation mechanism was studied during FSW of 304L stainless steel. • THERMOCALC analysis was performed to obtain possible formation temperatures for sigma phase. • Nano-mechanical twins were found in the TMAZ region.

36 MATERIALS SCIENCE↗

Structure and good piezoelectric performance in the complex system of Pb[(Zn,Ni)Nb]O 3 –Pb[(In,Yb)Nb]O 3 –Pb(Zr,Hf,Ti)O 3

High-performance piezoelectrics are always demanded for the high-end application. In this study, a complex piezoelectric system of 0.49Pb(Zn 1/2 Ni 1/2 ) 1/3 Nb 2/3 O 3 – x Pb(In 1/2 Yb 1/2 ) 1/2 Nb 1/2 O 3 –(0.51 – x )Pb(Zr 1/2 Hf 1/2 ) 0.1 Ti 0.9 O 3 (0.16 ≤ x ≤ 0.23) was fabricated through the solid-state method. The structure, ferroelectric, piezoelectric, and dielectric properties were investigated. The optimum piezoelectric coefficient d 33 of 761 pC/N, high Curie temperature of 169 °C, dielectric permittivity ( ε r ) of 4557, and electromechanical coupling coefficient ( k p ) of 63% were found at the morphotropic phase boundary composition of x = 0.19, which are superior to other complex piezoelectric materials. In particular, a significant large-signal d 33 * of 913 pm/V and low strain hysteresis (6%) was obtained in the temperature range of 20–170 °C. Temperature-dependent x-ray diffraction (XRD) has demonstrated that good temperature stability is put down to the structure stability. The agreement between the calculated lattice strain from in situ high-energy synchrotron XRD data and the macroscopic measurements suggests that the large lattice strain has a dominant contribution to the high piezoelectric response. The high piezoelectric performance and good temperature stability makes it potential for application.

36 MATERIALS SCIENCE↗

Three dimensional finite-element analysis of finite-thickness fracture specimens

The stress-intensity factors for most of the commonly used fracture specimens (center-crack tension, single and double edge-crack tension, and compact), those that have a through-the-thickness crack, were calculated using a three dimensional finite-element elastic stress analysis. Three-dimensional singularity elements were used around the crack front. The stress intensity factors along the crack front were evaluated by using a force method, developed herein, that requires no prior assumption of either plane stress or plane strain. The calculated stress-intensity factors from the present analysis were compared with those from the literature whenever possible and were generally found to be in good agreement. The stress-intensity factors at the midplane for all specimens analyzed were within 3 percent of the two dimensional plane strain values. The stress intensity factors at the specimen surfaces were considerably lower than at the midplanes. For the center-crack tension specimens with large thickness to crack-length ratios, the stress-intensity factor reached a maximum near the surface of the specimen. In all other specimens considered the maximum stress intensity occurred at the midplane.

Raju, I. S.↗

Hydride effects on discharged fuel clad related to accident conditions during dry storage and handling - 2016-0043

Safe handling of nuclear reactor discharged fuel requires an understanding of how the fuel (cladding) will perform under the various encountered conditions, including off-normal events, such as drop events in handling the storage canister. Clad failures under two distinct loading modes are considered: a diametrical pinch mode and an axial-bend mode. The mechanical response to the pinch mode and the bend mode loading are evaluated with ring compression testing (RCT) and three-point bend (TPB) testing, respectively. ZIRLO{sup R} clad samples were hydrogen charged to levels from 100 ppm to 800 ppm and then subjected to a hydride reorientation treatment involving heating to 400 deg. C and cooling while under hoop stresses ranging from 90 MPa to 170 MPa. Radial hydride reorientations were characterized and RCT and TPB tests were performed over a temperature range of ambient to 200 deg. C. Ductile-to-brittle transition temperatures (DBTT) were determined. Using finite element analysis (FEA), true stresses and strains are calculated and comparisons made between the RCT and TPB test modes. Because of the anisotropic properties of the clad and the relative orientation and generic effects of the hydrides, the DBTT was observed to be strongly dependent on the mode of strain application such that a DBTT associated with an RCT test is different from a DBTT obtained using an axial-bend test. Although the degree of radial hydriding strongly affected the pinch-mode RCT test, the same radial hydride impact was not observed for the axial-bend TPB test, which was affected strongly by the bulk hydride levels and not by the fraction of radial hydrides. (authors)

36 MATERIALS SCIENCE↗

Nonlinear behavior of circular plates with work hardening

Tests were performed on two simply supported plates of aluminum alloy 2024-0, under a central concentrated load, with peak deflections up to 2.6 times the thickness. The load was provided by a small-diameter hard-steel rod. The plates had diameter-to-thickness ratios (D/h) of 20 and 41. Measurements were made of load, deflections and strains; membrane and bending strains were calculated from the test data. The test data are presented in comparison with theoretical predictions generated by the finite-element-computer code PLANS, which includes material and geometric nonlinearities. The theoretical prediction was excellent for deflections, and generally good for strains, when the central force was represented by a line load around the loading rod's contact circle.

Winter, R.↗

Validation of Numerical Models of the Offshore Wind Turbine From the Alpha Ventus Wind Farm Against Full-Scale Measurements Within OC5 Phase III

The main objective of the Offshore Code Comparison Collaboration Continuation, with Correlation (OC5) project is validation of aero-hydro-servo-elastic simulation tools for offshore wind turbines (OWTs) through comparison of simulated results to the response data of physical systems. Phase III of the OC5 project validates OWT models against the measurements recorded on a Senvion 5M wind turbine supported by the OWEC Quattropod from the alpha ventus offshore wind farm. The following operating conditions of the wind turbine were chosen for the validation: (1) idling below the cut-in wind speed, (2) rotor-nacelle assembly (RNA) rotation maneuver below the cut-in wind speed, (3) power production below and above the rated wind speed, and (4) shutdown. A number of validation load cases were defined based on these operating conditions. The following measurements were used for validation: (1) strains and accelerations recorded on the support structure and (2) pitch, yaw, and azimuth angles, generator speed, and electrical power recorded from the RNA. Strains were not directly available from the majority of the OWT simulation tools; therefore, strains were calculated based on out-of-plane bending moments, axial forces, and cross-sectional properties of the structural members. The simulation results and measurements were compared in terms of time series, discrete Fourier transforms, power spectral densities, and probability density functions of strains and accelerometers. A good match was achieved between the measurements and models setup by OC5 Phase III participants.

17 WIND ENERGY↗

Compressive Tests of a Monocoque Box

A monocoque box specimen of aluminum alloy was subjected to end compression and the strains in the stringers were measured up to loads at which permanent set became noticeable. The stringer strains at low loads agreed closely with those computed from the assumption of uniform stress distribution. Buckling of the 0.026-inch sheet between stringers and of the 0.075-inch shear web took place at stresses in accord with theoretical values. Permanent set became noticeable at a load of 115,200 pounds, corresponding to an average stringer stress of about 16,000 pounds per square inch. The measured average strain above the first buckling load was within 2 percent of the theoretical strain as calculated from the dimensions of the box and effective width formulas due to Marguerre and to Cox.

BOXES, MONOCOQUE - STRENGTH, COMPRESSIVE↗

Two simplified procedures for predicting cyclic material response from a strain history

Simplified inelastic analysis procedures were developed at NASA Lewis and Pratt & Whitney Aircraft for predicting the stress-strain response at the critical location of a thermomechanically cycled structure. These procedures are intended primarily for use as economical structural analysis tools in the early design stages of aircraft engine hot section components where nonlinear finite-element analyses would be prohibitively expensive. Both simplified methods use as input the total strain history calculated from a linear elastic analysis. The elastic results are modified to approximate the characteristics of the inelastic cycle by incremental solution techniques. A von Mises yield criterion is used to determine the onset of active plasticity. The fundamental assumption of these methods is that the inelastic strain is local and constrained from redistribution by the surrounding elastic material.

Kaufman, A.↗

Elastic-plastic deformation of a metal-matrix composite coupon with a center slot

A comprehensive experimental analysis of deformations of the surface of a metal-matrix specimen is reported. The specimen is a 6-ply 0 + or - 45 sub s boron-aluminum tensile coupon with a central slot. Moire interferometry is used for high-sensitivity whole-field measurements of in-plane displacements. Normal and shear strains are calculated from displacement gradients. Displacement fields are analyzed at various load levels from 15% to 95% of the failure load. Deformations of the boron fibers could be distinguished from those of the matrix. Highly localized plastic slip zones occur tangent to the ends of the slot. Shear strains and concurrent transverse compressive strains in the slip zones reach approximately 10% and 1%, respectively. Upon unloading, elastic recovery in surrounding regions causes a reverse plastic shear strain in the slip zone of about 4%. Longitudinal normal strains on the unslotted ligament peak at the slot boundary at about 1% strain. The strain concentration factor at the end of the slot decreases with load level and the advance of plasticity.

Post, D.↗

Geodetic Measurement of Deformation East of the San Andreas Fault in Central California

Triangulation and trilateration data from two geodetic networks located between the western edge of the Great Valley and the San Andreas fault have been used to calculate shear strain rates in the Diablo Range and to estimate the slip rate along the Calaveras and Paicines faults in Central California. Within the Diablo Range the average shear strain rate was determined for the time period between 1962 and 1982 to be 0.15 + or - 0.08 microrad/yr, with the orientation of the most compressive strain at N 16 deg E + or - 14 deg. The orientation of the principal compressive strain predicted from the azimuth of the major structures in the region is N 25 deg E. It is inferred that the measured strain is due to compression across the folds of this area: the average shear straining corresponds to a relative shortening rate of 4.5 + or - 2.4 mm/yr. From an examination of wellbore breakout orientations and the azimuths of P-axes from earthquake focal mechanisms the inferred orientation of maximum compressive stress was found to be similar to the direction of maximum compressive strain implied by the trend of local fold structures. Results do not support the hypothesis of uniform fault-normal compression within the Coast Ranges. From trilateration measurements made between 1972 and 1987 on lines that are within 10 km of the San Andreas fault, a slip rate of 10 to 12 mm/yr was calculated for the Calaveras-Paicines fault south of Hollister. The slip rate of the Paicines fault decreases to 4 mm/yr near Bitter.

Sauber, Jeanne M.↗

Compact Simultaneous-beam Optical Strain Measurement System, Phase 5

Recent advances on the laser speckle strain measurement system under development at NASA Lewis Research Center have resulted in a compact, easy-to-use measurement package having many performance improvements over previous systems. NASA has developed this high performance optical strain measurement system for high temperature material testing applications. The system is based on I. Yamaguchi's two-beam speckle-shift strain measurement theory, and uses a new optical design that allows simultaneous recording of laser speckle patterns. This design greatly improves system response over previous implementations of the two-beam speckle-shift technique. The degree of immunity to transient rigid body motions is no longer dependent on the data transfer rate. The system automatically calculates surface strains at a frequency of about 5 Hz using a high speed digital signal processor in a personal computer. This system is fully automated, and can be operated remotely. This report describes the designs and methods used by the system, and shows low temperature strain test results obtained from small diameter tungsten-rhenium and palladium-chrome wires.

Lant, Christian T.↗

Growth and characterization of undoped and Mn doped lead-free piezoelectric NBT–KBT single crystals

Highlights: • Single crystals of undoped and Mn doped NKBT crystals are grown by spontaneous nucleation. • Temperature and frequency dependent dielectric constant and loss are measured. • Dielectric constant has increased and the loss has reduced on Mn doped NKBT. • Concentration of oxygen vacancies has been reduced in Mn doped NKBT. • The activation energy for undoped and Mn doped NKBT are calculated. - Abstract: Lead-free piezoelectric single crystals of undoped and 1 wt% Mn doped 0.80 Na{sub 0.5}Bi{sub 0.5}TiO{sub 3}–0.20 K{sub 0.5}Bi{sub 0.5}TiO{sub 3} (NKBT) was grown using self-flux. Powder X-ray diffraction analysis revealed that the grown crystals belong to tetragonal system at room temperature. The lattice strain was calculated from Williamson Hall relation for undoped and Mn doped NKBT crystals. A significant change is observed in dielectric behavior of Mn doped NKBT when compared to undoped sample. The diffuseness increased substantially on Mn doped NKBT which masked the ferroelectric to antiferroelectric transition in the dielectric constant plot. The AC impedance study revealed that the conduction is governed by the singly ionized oxygen vacancy. Further, the decrease in the conductivity on Mn doping suggests that Mn replaces the Bi vacancy, which reduces the oxygen vacancy.

36 MATERIALS SCIENCE↗

HolT Hunter: Software for Identifying and Characterizing Low-Strain DNA Holliday Triangles

Synthetic DNA nanostructures are most commonly held together via Holliday junctions. These junctions allow for a wide variety of different angles between the double helices they connect. Nevertheless, only constructs with a very limited selection of angles have been built, to date, because of the computational complexity of identifying structures that fit together with low strain at odd angles. I have developed an algorithm that finds over 95% of the possible solutions by breaking the problem down into two portions. First, there is a problem of how smooth rods can form triangles by lying across one another. This problem is easily handled by numerical computation. Second, there is the question of how distorted DNA double helices would need to be to fit onto the rod structure. This strain is calculated directly. The algorithm has been implemented in a Mathematica 8 notebook called Holliday Triangle Hunter. A large database of solutions has been identified. Additional interface software is available to facilitate drawing and viewing models.

59 BASIC BIOLOGICAL SCIENCES↗

Dynamic High-Temperature Tensile Characterization of an Iridium Alloy with Kolsky Tension Bar Techniques

In this study, conventional Kolsky tension bar techniques were modified to characterize an iridium alloy in tension at elevated strain rates and temperatures. The specimen was heated to elevated temperatures with an induction coil heater before dynamic loading; whereas, a cooling system was applied to keep the bars at room temperature during heating. A preload system was developed to generate a small pretension load in the bar system during heating in order to compensate for the effect of thermal expansion generated in the high-temperature tensile specimen. A laser system was applied to directly measure the displacements at both ends of the tensile specimen in order to calculate the strain in the specimen. A pair of high-sensitivity semiconductor strain gages was used to measure the weak transmitted force due to the low flow stress in the thin specimen at elevated temperatures. The dynamic high-temperature tensile stress–strain curves of a DOP-26 iridium alloy were experimentally obtained at two different strain rates (~1000 and 3000 s -1 ) and temperatures (~750 and 1030°C). The effects of strain rate and temperature on the tensile stress–strain response of the iridium alloy were determined. Finally, the iridium alloy exhibited high ductility in stress–strain response that strongly depended on strain-rate and temperature.

36 MATERIALS SCIENCE↗

X-Ray Studies of GaN Film Grown on Si Using Electrochemical Deposition Techniques

This paper reports on the X-ray studies of GaN thin films deposited on Si (111) substrate at different current density using electrochemical deposition technique. The structural properties of GaN films were studied by X-ray diffraction (XRD). XRD analysis showed that hexagonal wurtzite and cubic zinc blende GaN phases were both deposited on Si (111). The lattice constants, the average size of h-GaN crystals and the in-plane (along a-axis) and out of plane (along c-axis) strains were calculated from XRD analysis.

36 MATERIALS SCIENCE↗

Structural characterization of InSb thin films grown by electrodeposition

In the present work we have grown InSb thin films on brass substrates, using the electrodeposition technique. The electrochemical baths used in the growth were made up of aqueous solutions of InCl{sub 3} and SbCl{sub 3} mixed together in various proportions. The films grown were characterized by X-Ray diffraction (XRD), Scanning Electron Microscopy (SEM), and Energy Dispersive Analysis of X-rays (EDAX). Compositional studies show that stoichiometric InSb films can be prepared from a bath containing 0.05M InCl{sub 3} and 0.04M SbCl{sub 3}. XRD studies reveal that the films grown are polycrystalline having the zinc blende structure with (111) orientation. Crystallite size, dislocation density and strain were calculated using the XRD results. Optical transmission spectra were recorded using an FTIR spectrophotometer. The value of direct band gap was found to be around 0.20 eV for the thin films having the best stoichiometry.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗