Search NASA⌕ Search

SEARCH · Search NASA

Results for “TEST PARTICLES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Microstructure effects on high velocity microparticle impacts of copper

Constitutive models can fail to predict high-rate deformation behavior due to their inability to account for microstructural effects. In part, this is because of a dearth of experimental benchmarking data in the high strain-rate, low pressure regime, since many high-rate experiments also probe a region of strong shockwaves, at which point microstructure effects no longer play a primary role. This work uses laser-induced particle impact testing to quantitatively study high velocity impacts of small, rigid alumina microspheres on flat copper substrates with varying amounts of initial cold work in the weak shock regime, but at very high strain rates up to ~10 7 s –1 . Through paired experiments and numerical simulations, this work shows that the initial microstructure condition can have significant influence on dynamical mechanical properties in this range. Specifically, prior work hardening of the copper substrate leads to increased rebounding of the microparticles (i.e., less plastic dissipation in the impact) as well as smaller craters. Each of these experimental measurables can be converted into a strength measure, i.e., the dynamic yield strength or dynamic hardness, respectively, neither of which is well predicted consistently by existing constitutive laws. The general trend of hardening can be captured by such models by incorporating an existing “pre-strain,” suggesting that future calibration of the materials parameters may yield a good fit over a broader range of conditions. Our results emphasize the importance of reporting the microstructural condition in dynamic studies, as well as the necessity of accounting for these factors when formulating and optimizing constitutive models.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Development of an ab initio learned model of electron deposition range in deuterium-tritium plasmas through time-dependent density functional theory calculations and machine learning

Accurate hydrodynamic modeling for laser-direct-drive (LDD) inertial-confinement-fusion (ICF) relies on precise calculations of the electron thermal conduction in all target materials. The nonlocal stopping range of electrons in ICF plasmas directly influences thermal conduction; yet, no first principles model exists for the electron mean free path in the conduction-zone regime. This work utilized time-dependent stochastic density-functional theory (TD-sDFT) to calculate the electron stopping power in deuterium-tritium (DT) plasmas at (ρ, T) conditions relevant to the conduction zone and the compressed shell in ICF. Using a combination of our TD-sDFT data and already established analytical models, we developed and trained an artificial neural network to create a global model for the nonlocal electron deposition range, λ E . We compared our machine-learning (ML) based model for λ E to the currently-used modified-Lee-More model in LDD radiation-hydrodynamic codes, such as lilac, and saw an overall decrease in the deposition range. To understand the effects of λ E on LDD ICF implosion dynamics, we implemented the ML-based model into lilac; specifically, we looked at designs consistent with a current experiment on the OMEGA laser and for a newly designed LDD-ICF target for the future OMEGA-Next facility. In both cases, we saw an overall drop in predicted ablation pressure, peak areal density, and neutron yield due to the reduced thermal conduction (smaller λ E ) in DT plasmas. Comparisons with the experiment on OMEGA are also made.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Measurements of the time-dependent cosmic-ray Sun shadow with seven years of IceCube data: Comparison with the Solar cycle and magnetic field models

Observations of the time-dependent cosmic-ray Sun shadow have been proven as a valuable diagnostic for the assessment of solar magnetic field models. Here, seven years of IceCube data are compared to solar activity and solar magnetic field models. A quantitative comparison of solar magnetic field models with IceCube data on the event rate level is performed for the first time. Additionally, a first energy-dependent analysis is presented and compared to recent predictions. We use seven years of IceCube data for the moon and the Sun and compare them to simulations on data rate level. The simulations are performed for the geometrical shadow hypothesis for the moon and the Sun and for a cosmic-ray propagation model governed by the solar magnetic field for the case of the Sun. We find that a linearly decreasing relationship between Sun shadow strength and solar activity is preferred over a constant relationship at the 6.4σ level. We test two commonly used models of the coronal magnetic field, both combined with a Parker spiral, by modeling cosmic-ray propagation in the solar magnetic field. Both models predict a weakening of the shadow in times of high solar activity as it is also visible in the data. We find tensions with the data on the order of 3σ for both models, assuming only statistical uncertainties. The magnetic field model CSSS fits the data slightly better than the PFSS model. This is generally consistent with what is found previously by the Tibet AS-γ Experiment; a deviation of the data from the two models is, however, not significant at this point. Regarding the energy dependence of the Sun shadow, we find indications that the shadowing effect increases with energy during times of high solar activity, in agreement with theoretical predictions.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Absorption and Transport Effects Induced in Plasmas by the Interaction of Electrons with Laser Speckles

Here, we show that the ponderomotive force associated with laser speckles can scatter electrons in a laser-produced plasma in a manner similar to Coulomb scattering. Analytic expressions for the effective collision rates are given. The electron-speckle collisions become important at high laser intensity or during filamentation, affecting both long- and short-pulse laser intensity regimes. As an example, we find that the effective collision rate in the laser-overlap region of hohlraums on the National Ignition Facility is expected to exceed the Coulomb collision rate by 1 order of magnitude, leading to a fundamental change to the electron transport properties. At the high intensities characteristic of short-pulse laser-plasma interactions (I ≳ 10 17 W cm –2 ), the scattering is strong enough to cause the direct absorption of laser energy, generating hot electrons with energy scaling as E ≈ 1.44 (I/10 18 W cm –2 ) 1/2 MeV , close to experimentally observed results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Redistribution of radionuclides in irradiated AGR-1 UCO TRISO fuel after 1800 °C safety testing

Release of radionuclides from intact tristructural-isotropic (TRISO) coated particle fuel at normal and accident conditions is a primary metric of fuel performance. The distribution of fission products and actinides in the TRISO layers of individual particles provides insight on radionuclide transport and release behavior and was determined using scanning electron microscopy analysis. Particles were isolated from an irradiated fuel compact (AGR-1 Compact 4-4-2) and analyzed as-irradiated or after individual particle safety-testing at 1800 °C for 650 h. Particles were selected for comparison based on their remaining 110mAg fission product inventory. These comparisons corroborated the observation that the 110m Ag inventory is a marker for relative irradiation temperature based on observed radionuclide distribution in the SiC layer. The comparison also indicated that the in-pile behavior influences the fission product and actinide species interactions with the TRISO layers during high temperature exposure after irradiation. The analysis confirms both palladium and uranium diffusion, as well as other species, are active in the UCO TRISO fuel system at 1800 °C and that palladium transport is active at lower temperatures relative to uranium. While diffusion across the SiC layer was observed, the intact nature of the SiC layer after the 1800 °C, 650-h exposure indicates the SiC layer maintained its functionality as a fission product barrier by mitigating release of radionuclides at beyond accident margin temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Carbon and Hydrocarbon Particle Seeding in Air-Breathing Rotating Detonation Engine

Within the power generation community, the rotating detonation engine (RDE) is only growing in popularity with its increased performance, simple mechanism, and operation. Although significant testing is underway to characterize the RDE for integration with conventional gas turbines, this entire system is still at a relatively low technology readiness level. In the midst of RDE research, there is an initiative to understand solid particle seeding effects in the detonation performance. Under investigation at the University of Central Florida is a Department of Energy (DOE) 15.24 cm (6 in.) RDE, with a solid particle seeder in parallel with its H2 and air flow lines. Previous work on this system involved carbon particle detonation; however, the tested particles were taken one step further to include more sustainable, greener hydrocarbon particles. Testing of powdered sugar, peanut flour, and cornstarch, along with previous carbon black tests have shown not only successful detonability, but a noticeable effect on the detonation wave dynamics. Side-by-side with a particle burning model being developed, an operational map can be determined for the hydrocarbon particles particularly, which can be tuned with the local flow conditions to achieve peak operability while replacing fuels with sustainable alternatives that could even be grown.

Engineering↗
DOE OSTI2021

Scalable fabrication of high activity nanoporous copper powders for electrochemical CO 2 reduction via ball milling and dealloying

Electrochemical CO 2 reduction (ECR) is a promising technology to close the anthropic CO 2 circle using renewable energy to achieve carbon neutrality. Future commercialization of ECR will require the development of new catalyst synthesis routes that will allow significant upscaling of catalyst production from current research-level milligram quantities to the kilogram scale and beyond while maintaining the activity and selectivity demonstrated at the research level. Here, we report on generating and testing submicron-sized nanoporous copper (npCu) particles by using a scalable approach consisting of ball milling brittle Cu-based intermetallics followed by dealloying to add nanoporosity for high surface area. The resulting npCu particles have been tested in an industry-relevant large area (25 cm 2 ) electrolyzer platform and showed Faraday efficiencies (FE) for ethylene up to 34 % at current densities of 75–100 mA/cm 2 while keeping FE for hydrogen less than 30 %. Our results demonstrate that a combination of ball milling and dealloying is a promising approach to generate large quantities of high activity and high surface area npCu particles for ECR at an industry-relevant scale.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Improved Particle Heat Transfer by way of Bimodal Particle Distributions for High Temperature Solar Thermal Energy

High temperature solar thermal facilities are looking to increase operating temperatures through novel heat transfer media, one such being solid particles. These particles operating at high temperatures will require transferring their thermal energy into another working fluid like supercritical carbon dioxide which can be used in advanced power cycles. Achieving high heat transfer between the particles and supercritical carbon dioxide is essential to high efficiency and low-cost operation. Therefore, optimizing the thermal conductivity of these particles is one potential way to ensure high performance. Traditionally, unimodal particle distributions have been employed in high temperature particle solar power plants. However, ambient temperature testing of bimodal particle distributions has revealed a superior thermal conductivity when compared to its unimodal counterpart at the same temperature. This data was obtained by certified, off-the-shelf instruments that can effectively simulate the conditions a particle would be exposed to in a high temperature solar thermal system. Data obtained in this way suggests that the increased thermal conductively imputed by a bimodal particle distribution is significant at working temperatures in solar facilities. Furthermore, the thermal conductivity of these bimodal particle distributions peaks when the best combination of large and small particles is applied. At high temperatures, binary particle distributions are compared to monodispersed distributions of larger particles where heat transfer is more prolific due to the increased surface radiation. Various thermal conductivity, porosity and heat exchanger models are explored in conjunction with data acquired up to 700 C.

Stout, Dallin (ORCID:0009000294586091)↗
DOE OSTI2023

Investigation of Best-Practices and Computationally Inexpensive Radiative Exchange Models for Discrete Element Method Modeling of Aluminosilicate Particles in Concentrating Solar Power Environments

Chemically inert, aluminosilicate based particles have been investigated as both a thermal transport and sensible energy storage medium for concentrating solar power facilities. These particles will experience a wide range of operating temperatures (300-1000 K) and handling conditions (dense to dilute falling particle curtains, dense granular flows, or dense structures), requiring specially-designed and optimized infrastructures. The relative influence of collisional and frictional interactions between particles varies based on temperature-dependent particulate properties and greatly impacts the bulk, granular flow behavior. These underlying physics are captured using discrete element method modeling tools. However, this modeling method is computationally expensive as each particle position and interaction is tracked during the simulation. These modeling methods are further complicated by introducing temperature-dependent particle properties, high-temperature radiative exchange, and directional irradiation sources experienced by granular flows in concentrating solar power environments. In this study, coupled experimental and numerical slump testing of aluminosilicate particles was performed and computationally efficient radiative exchange models were evaluated to establish best-practices for discrete element method models for concentrating solar power environments. The three particle types investigated included Carbobead HSP 30 /60, Carbobead CP 30/60, and Granusil 4030. Existing modeling limitations and computationally-efficient multi-modal heat transfer models were evaluated using Aspherix®, a commercial discrete element method software. High-temperature (< 1073 K) slump testing of aluminosilicate particles was performed to investigate the deviation between experimentally-observed and numerically-predicted angles of repose introduced by computation-time reduction practices including the relaxation of the particle elastic modulus and coarse-graining. Coarse-graining is used to use a single modeled particle that is representative of a collection of smaller particles, decreasing the computational cost at the expense of geometric accuracy. Additionally, relaxation of the elastic modulus is used to reduce computational time at the expense of an increased, modeled particle overlap. Prior studies have determined that aluminosilicate particles retain a high elastic modulus at high temperatures (< 1073 K), requiring small simulation timesteps to ensure resolved contact forces resemble appropriate solid mechanics. A parametric study was performed to evaluate the influence of computation time improvements on the deviation between experimental and modeled angle of repose across high temperatures < 1073 K. Additionally, numerical case studies were performed on candidate particle systems at varying porosities and temperatures. These studies were performed to investigate the influence of computationally-efficient radiative-exchange modeling methods coupled to Aspherix® on modeled accuracy and computation time. The recently-developed distance-based approximation was evaluated in estimating radiative exchange between particles and participating surfaces located in close proximity. The distance based approximation was developed to use tabulated estimates of the radiative distribution factor between individual particles and surfaces in close proximity (< 40 particle radii). These methods were expanded to the aluminosilicate particles of interest, including the influence of particle size distributions. To capture radiative exchange between particles and surfaces not in close proximity (> 40 particle radii) and to capture the absorption of directional irradiation from concentrating solar resources, a volumetrically-averaged radiative distribution factor was calculated between the modeled granular flow and surfaces using Monte Carlo ray-tracing for participating media. Volume-averaged absorption and scattering coefficients were predicted using a volumetric discretization of the modeled domain with monodisperse approximations based on geometric optics and experimentally-determined scattering phase functions for aluminosilicate particles.

14 SOLAR ENERGY↗
DOE OSTI2022

Shock-driven dispersal of a corrugated finite-thickness particle layer

A research area emerging in the multiphase flow community is the study of shock-driven multiphase instability (SDMI), a gas–particle analog of the traditional fluid-fluid Richtmyer–Meshkov instability (RMI). In this work, we study the interaction of planar air shocks with corrugated glass particle curtains through the use of numerical simulations with an Eulerian–Lagrangian approach. One objective of this study is to compare the simulated particle curtains to a comparable set of shock tube experiments performed to analyze traditional RMI of a gas curtain. The simulations are set to match the experimental shock Mach numbers and perturbation wavelengths (3.6 and 7.2 mm) while also matching the Atwood number of the experiments to the multiphase Atwood number of the simulations. Varying particle diameters are tested in the simulations to explore the impact of particle diameter on the evolution of the particle curtain. This simulation setup allows for a one-to-one comparison between RMI and SDMI under comparable conditions while also allowing for a separate study into the validity of the use of the multiphase Atwood number to compare the single-phase and multiphase instabilities. In particular, we show that the comparison depends on the diameter of the particles (thus, dependent on the Stokes number of the flow). A second objective of this study is to analyze the effect of the initial particle volume fraction on the evolution of the curtain and the behavior of the instability. This is done through analyzing the effect of the multiphase terms of the vorticity evolution equation on the vorticity deposition in SDMI. Also discussed is the effect of the particle diameter on the multiphase generation terms as well as in the baroclinic vorticity generation term in SDMI as the shock passes over the curtain.

42 ENGINEERING↗
DOE OSTI2022

Multiscale Shear Properties and Flow Performance of Milled Woody Biomass

One dominant challenge facing the development of biorefineries is achieving consistent system throughput with highly variant biomass feedstock quality and handling performance. Current handling unit operations are adapted from other sectors (primarily agriculture), where some simplifying assumptions about granular mechanics and flow performance do not translate well to a highly compressible and anisotropic material with nonlinear time- and stress-dependent properties. This work explores the shear and frictional properties of loblolly pine at multiple experimental test apparatus and particle scales to elucidate a property window that defines the shear behavior over a range of material attributes (particle size, size distribution, moisture content, etc.). In general, it was observed that the bulk internal friction and apparent cohesion depend strongly on both the stress state of the sample in granular shear testers and the overall particle size and distribution span. For equipment designed to characterize the quasi-static shear stress failure of bulk materials ranging from 50 to 1,000 ml in test volume, similar test results were observed for finely milled particles (50% passing size of 1.4 mm) with a narrow size distribution (span between 10 and 90% passing size of 0.9 mm), while stress chaining and over-torque issues persisted for the bench-scale test apparatus for larger particle sizes or widely dispersed sample sizes. Measurement of the anisotropic particle–particle friction ranged from coefficients of approximately 0.20 to 0.45 and resulted in significantly higher and more variable friction measurements for larger particle sizes and in perpendicular alignment orientations. To supplement these laboratory-scale properties, this work explores the flow of loblolly pine and Douglas fir through a pilot-scale wedge-shaped hopper and a screw feeder. For the gravity-driven hopper flow, the critical arching distance and mass discharge rate ranged from approximately 10 to 30 mm and 2 to 16 tons/hour, respectively, for both materials, where the arching distance depends strongly on the overall particle size and depends less on the hopper inclination angle. Comparatively, the auger feeder was found to be much more impacted by the size of the particles, where smaller particles had a more consistent and stable flow while consuming less power.

09 BIOMASS FUELS↗
DOE OSTI2025

Reirradiation and Post-reirradiation Heating Tests of Loose AGR-2 TRISO Particles and AGR-3/4 Fuel Compacts

To address the lack of data on the behavior of short-lived fission products I-131 (t1/2 = 8.02 d) and Xe-133 (t1/2 = 5.24 d) in the TRISO fuel system, loose AGR-2 particles and kernels were reirradiated in NRAD and subjected to post-reirradiation heating in the FACS furnace. This provided data on the release of fission products from exposed kernels, and the results were used to establish FACS condensation plate collection efficiencies for temperatures of 1000, 1200, and 1400°C where previously, the only collection efficiencies were for 1600°C tests. These new collection efficiencies were then applied to the NRAD-FACS tests of entire AGR-3/4 fuel compacts. Understanding the relative behavior of short-lived I-131, for example, is important because it is a significant contributor to offsite dose during postulated accidents, and Xe-133 has previously been used as a conservative indicator of I-131 behavior. These data will be used to support refinement of fission product transport models and HTGR source-term analyses.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗