Search NASA⌕ Search

SEARCH · Search NASA

Results for “TURBINES, GAS - PERFORMANCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Evaluating steam oxidation kinetics of environmental barrier coatings

Environmental barrier coatings (EBCs) are a commercially proven means of protecting SiC-based materials in gas turbine environments. However, there are little specific data in the literature on the impact of coatings like Yb 2 Si 2 O 7 on preventing accelerated SiO 2 growth in the presence of H 2 O. Quantification of reduced rates are necessary for evaluating and comparing EBC effectiveness and incorporation of silica growth rates into future EBC lifetime models. In this study, baseline kinetics of silica formation on bare Si and chemically vapor deposited (CVD) SiC in the 1250–1425 °C range were obtained via 100 h isothermal exposures in dry air and steam environments utilizing a SiC reaction tube to mitigate specimen volatility. An Arrhenius plot of the resulting rates was constructed, representing baseline minimum and maximum rates for Si and SiC oxidation at ambient pressure. Various EBC systems on CVD SiC substrates including air plasma sprayed (APS) EBCs with and without a Si bond coating and with surface roughening to enhance Yb 2 Si 2 O 7 adhesion were subjected to 1-h furnace cycle testing in air with 90vol%H 2 O at 1250–1350°C for up to 500 cycles. After exposure, silica formation rates were measured and compared to the baseline rates to assess EBC effectiveness, where EBC effectiveness is gauged as the propensity to reduce underlying rates of silica formation. With a Si bond coating, a ~180 µm Yb 2 Si 2 O 7 (YbDS) top coating reduced rates over the entire 1250°-1350°C range. Without a Si bond coating, ~60 µm (YbDS) coatings deposited directly onto CVD SiC exhibited poor adhesion, and had to be deposited onto substrates with enhanced roughness at 1350°C. Finally, while exhibiting good adhesion at 1350°C, overall the single layer YbDS coating exhibited a decreasing effectiveness from 1250° to 1350°C.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Accelerated oxidation during 1350°C cycling of ytterbium silicate environmental barrier coatings

We report environmental barrier coatings (EBCs) will be needed to protect SiC-based ceramic matrix composite components for the next generation of high-efficiency industrial gas turbines (IGTs). The IGT application will require ≥25 kh lifetimes, and little data are available on EBC failure mechanisms, particularly at ≥1300°C. Initial 1-h furnace cycle testing at 1350°C in 90 vol% H 2 O/10 vol% air was conducted ≥1000 cycles on thermally sprayed ytterbium disilicate (YbDS) coatings with and without an Si bond coating. By ≥1000 h, both EBCs formed thick, highly cracked, and fully crystalline cristobalite scales. Comparison of thermally grown oxide (TGO) microstructure and kinetics to isothermal rates of Si and SiC steam oxidation indicated a departure from slow-growing parabolic growth to more rapid rates of silica formation. Possible mechanisms and implications for this acceleration are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Phase stability and tensorial thermal expansion properties of single to high-entropy rare-earth disilicates

Temperature limitations in nickel-base superalloys have resulted in the emergence of SiC-based ceramic matrix composites as a viable replacement for gas turbine components in aviation applications. Higher operating temperatures allow for reduced fuel consumption but present a materials design challenge related to environmental degradation. Rare-earth disilicates (RE 2 Si 2 O 7 ) have been identified as coatings that can function as environmental barriers and minimize hot component degradation. In this work, single- and multiple-component rare-earth disilicate powders were synthesized via a sol-gel method with compositions selected to exist in the monoclinic C 2/m phase (β phase). Phase stability in multiple cation compositions was shown to follow a rule of mixtures and the C 2/m phase could be realized for compositions that contained up to 25% dysprosium, which typically only exists in a triclinic, P $\bar1$, phase. All compositions exhibited phase stability from room temperature to 1200°C as assessed by X-ray diffraction. The thermal expansion tensors for each composition were determined from high-temperature synchrotron X-ray diffraction and accompanying Rietveld refinements. It was observed that ytterbium-containing compositions had larger changes in the α 31 shear component with increasing temperature that led to a rotation of the principal axes. Principal axes rotation of up to 47° were observed for ytterbium disilicate. The results suggest that microstructure design and crystallographic texture may be essential future avenues of investigation to ensure thermo-mechanical robustness of rare-earth disilicate environmental barrier coatings.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The Effect of the Degree of Premixedness on Self-Excited Combustion Instability

The use of lean, premixed fuel and air mixtures is a common strategy to reduce NO x emissions in gas turbine combustors. However, this strategy causes an increased susceptibility to self-excited instability, which manifests as fluctuations in heat release rate, flow velocity, and combustor acoustics that oscillate in-phase in a feedback loop. Here, this study considers the effect of the level of premixedness on the self-excited instability in a single-nozzle combustor. In this system, the fuel can be injected inside the nozzle to create a partially-premixed mixture or far upstream to create a fully-premixed mixture, varying the level of premixedness of the fuel and air entering the combustor. When global equivalence ratio is held constant, the cases with higher levels of premixing have higher instability amplitudes. High-speed CH* chemiluminescence imaging shows that the flame for these cases is more compact and the distribution of the heat release rate oscillations is more concentrated near the corner of the combustor in the outer recirculation zones. Rayleigh index images, which are a metric for the relative phase of pressure and heat release rate oscillations, suggest that vortex rollup in the corner region is primarily responsible for determining instability characteristics when premixedness is varied. This finding is further supported through analysis of local flame edge dynamics.

42 ENGINEERING↗
DOE OSTI2021

Impact of Additive Manufacturing on Internal Cooling Channels With Varying Diameters and Build Directions

Abstract The use of additive manufacturing (AM) processes, such as direct metal laser sintering, provides the design freedom required to incorporate complex cooling schemes in gas turbine components. Additively manufactured turbine components have a range of cooling feature sizes and, because of the inherent three-dimensionality, a wide range of build angles. Previous studies have shown that AM built directions influence internal channel surface roughness that, in turn, augment heat transfer and pressure loss. This study investigates the impact of AM on channel feature size and builds direction relative to tolerance, surface roughness, pressure losses, and convective cooling. Multiple AM coupons were built from Inconel 718 consisting of channels with different diameters and a variety of build directions. An experimental rig was used to measure pressure drop to calculate friction factor and was used to impose a constant surface temperature boundary condition to collect Nusselt number over a range of Reynolds numbers. Significant variations in surface roughness and geometric deviations from the design intent were observed for distinct build directions and channel sizes. These differences led to notable impacts in friction factor and Nusselt number augmentations, which were a strong function of build angle.

Engineering↗
DOE OSTI2021

Ultra-High Temperature Thermal Conductivity Measurements of a Reactive Magnesium Manganese Oxide Porous Bed Using a Transient Hot Wire Method

Pelletized magnesium manganese oxide shows promise for high temperature thermochemical energy storage. It can be thermally reduced in the temperature range between 1250 °C and 1500 °C and re-oxidized with air at typical gas-turbine inlet pressures (1–25 bar) in the temperature range between 600 °C and 1500 °C. The combined thermal and chemical volumetric energy density is approximately 2300 MJ/m3. The rate at which a thermochemical storage module can be charged is limited by heat transfer inside the solid packed bed. Hence, the effective thermal conductivity of packed beds of magnesium-manganese oxide pellets is a crucial parameter for engineering Mg-Mn-O redox storage devices. We have measured the effective thermal conductivity of a packed bed of 3.66 ± 0.516 mm sized magnesium manganese oxide (Mn to Mg molar ratio of 1:1) pellets in the temperature range of 300–1400 °C. Since the material is electrically conductive at temperatures above 600 °C, the sheathed transient hot wire method is used for measurements. Raw data is analyzed using the Blackwell solution to extract the bed thermal conductivity. The effective thermal conductivity standard deviation is less than 10% for a minimum of three repeat measurements at each temperature. Experimental results show an increase in the effective thermal conductivity with temperature from 0.50 W/m °C around 300 °C to 1.81 W/m °C close to 1400 °C. We propose a dual porosity model to express the effective thermal conductivity as a function of temperature. This model also considers the effect of radiation within the bed, as this is the dominant heat transfer mode at high temperatures. The proposed model accounts for microscale pellet porosity, macroscale bed porosity, pellet size, solid thermal conductivity (phonon transport), and radiation (photon transport). The coefficient of determination between the proposed model and the experimental results is greater than 0.90.

Engineering↗
DOE OSTI2021

Accelerated Creep Test Qualification of Creep-Resistance Using the Wilshire–Cano–Stewart Constitutive Model and Stepped Isostress Method

In this paper, a qualification of accelerated creep-resistance of Inconel 718 is assessed using the novel Wilshire–Cano–Stewart (WCS) model and the stepped isostress method (SSM) and predictions are made to conventional creep data. Conventional creep testing is a long-term continuous process; in fact, the ASME B&PV III requires that 10,000+ h of experiments must be conducted to each heat for materials employed in boilers and/or pressure vessel components. This process is costly and not feasible for rapid development of new materials. As an alternative, accelerated creep testing techniques have been developed to reduce the time needed to characterize the creep resistance of materials. Most techniques are based upon the time-temperature-stress superposition principle that predicts minimum-creep-strain-rate (MCSR) and stress-rupture behaviors but lack the ability to predict creep deformation and consider deformation mechanisms that occur for experiments of longer duration. The SSM has been developed, which enables the prediction of creep deformation response as well as reduce the time needed for qualification of materials. The SSM approach has been successful for polymer, polymeric composites, and recently has been introduced for metals. In this study, the WCS constitutive model, calibrated to SSM test data, qualifies the creep resistance of Inconel 718 at 750 °C and predictions are compared to conventional creep testing data. The WCS model has proven to make long-term predictions for stress-rupture, MCSR, creep deformation, and damage in metallic materials. The SSM varies stress levels after time interval adding damage to the material, which can be tracked by the WCS model. The SSM data is calibrated into the model and the WCS model generates realistic predictions of stress-rupture, MSCR, damage, and creep deformation. The calibrated material constants are used to generate predictions of stress-rupture and are postaudit validated using the National Institute of Material Science database. Similarly, the MCSR predictions are compared from previous studies. Finally, the creep deformation predictions are compared with real data and is determined that the results are well in between the expected boundaries. Material characterization and mechanical properties can be determined at a faster rate and with a more cost-effective method. This is beneficial for multiple applications such as in additive manufacturing, composites, spacecraft, and industrial gas turbines.

42 ENGINEERING↗
DOE OSTI2021

Energy demand reduction in the built environment using shallow geothermal integrated energy systems: Part II – Hybrid ground source heat pump for building heating

The research collection aims at finding the various possible opportunities for the effective integration of shallow geothermal energy (SGE) to decrease the energy demand in the built environment and to reduce emission associated with it. The direct utilization of SGE using a ground source heat pump (GSHP) has been reviewed in comprehensive review part I and part II. From the extensive review, we have found that the hybrid GSHP is needed to avoid ground thermal imbalance and peak demand. Hybrid GSHP can adopt various supplemental heat sources and sinks according to the local climatic conditions and the balance of energy demands. The primary focus on the integration of subsystems such as biomass, solar energy (PV, PVT, and collector), phase change material, micro gas turbine, and absorption heat pump with GSHP is presented for heating application. This comprehensive review part III highlights the recent research findings and a potential gap in hybrid GSHP for further research and developments

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Identification of High-Frequency Transverse Acoustic Modes in Multi-Nozzle Can Combustors

Abstract High frequency thermoacoustic instabilities are problematic for lean-premixed gas turbines. Identifying which acoustic mode is being excited is important, in that it provides insight into potential mitigation measures and mechanical stress/life. However, the frequency spacing between modes becomes quite close for high frequency instabilities in a can combustor. This makes it difficult to distinguish between the modes (e.g., the first transverse mode vs. a higher order axial/mixed mode) based upon frequency calculations alone, which inevitably have uncertainties in boundary conditions, temperature profiles, and combustion response. This paper presents a methodology to simultaneously identify the acoustic mode shapes in the axial and azimuthal directions from acoustic pressure measurements. Multiple high temperature pressure transducers, located at distinct axial and azimuthal positions, are flush mounted in the combustor wall. The measured pressure oscillations from each sensor are then used to reconstruct the pressure distributions by using a least squares method in conjunction with a solution of a three dimensional wave equation. In order to validate the methodology, finite element method (FEM) calculations with estimated post-flame temperature is used to provide the candidate frequencies and corresponding mode shapes. The results demonstrate the reconstructed mode shapes and standing/spinning character of transverse waves, as well as the associated frequencies, both of which are consistent with the FEM predictions. Nodal line location was also extracted from the experimental data during the instabilities in the pressure data.

Kim, J.↗
DOE OSTI2023

Flashback of Hydrogen-Methane Mixtures in a Fixed-Vane, Low-Swirl Burner at Atmospheric Pressure

Equivalence ratio at flashback, 𝜙FB, of low swirl injectors for 60% – 95% (H2, by mole) hydrogen-methane mixtures was determined experimentally in a < 100 kW atmospheric pressure burner. Pre-mixer velocities equaled 5, 7.5, and 10 m/s, with the reactants entering the burner at 294 K. The swirler design was selected following a literature review, and the test articles were additively manufactured. The test articles had two turning angles, 26° and 33°, with center-body hole diameters equaling 1.08 and 1.16 mm. A test article was built with each parameter combination, which yielded four test articles with measured swirl numbers varying from 0.43 to 0.49. The results showed agreement with prior work. 𝜙FB increased with increasing pre-mixer velocity and decreasing percent hydrogen. 𝜙FB was also observed to increase with swirl angle and decrease with increasing center-body hole diameter. The data was correlated using a semi-empirical quenching approach, with 𝐶quench=0.01, where the chemical time scale was calculated using a perfectly stirred reactor (PSR) model. Two different chemical kinetics mechanisms independently yielded the same results. The correlation makes the present small-scale laboratory results relevant to large, high-pressure gas turbines. The flashback data set is available for computational fluid dynamics (CFD) validation.

Searle, Matthew↗
DOE OSTI2022

Task Information Presentation System

Demonstrate a novel computer-based procedure solution for a multi-unit power plant. TIPS is developed to demonstrate a way to operate a highly automated plant. Currently, there are no plants (nuclear or non-nuclear) that can support this high level of automation. The purpose of TIPS is to help the industries think beyond the current conduct of operations. TIPS is designed to work with the GSE Systems' Combine-cycle gas turbine power plant simulator. TIPS uses the plant data from the simulator to make the user experience of the computer-based procedure more realistic.

Oxstrand, Johanna↗
DOE OSTI2020

Separating Nuclear Reactors from the Power Block with Heat Storage: A New Power Plant Design Paradigm

The Massachusetts Institute of Technology (MIT), Idaho National Laboratory (INL) and the Electric Power Research Institute (EPRI) conducted a workshop on Separating Nuclear Reactors from the Power Block with Heat Storage: A New Power Plant Design Paradigm. The workshop was held as three webinars (July 29, August 12 and August 26, 2020). These proceedings include this abstract, an executive summary, the main report and presentations. There are two reasons to consider a new design paradigm. First, the market is changing with (1) the addition of variable wind and solar that results in highly volatile electricity prices and (2) the goal of a low-carbon economy that requires (a) economic dispatchable electricity that is now provided by natural gas turbines in the United States and (b) heat for industry and commerce. Second, nuclear plant requirements have changed in the last 50 years suggesting that a lower-cost plant layout may be to separate the nuclear island from the power block with a clear separation of the nuclear island with nuclear requirements and the power block built to industrial standards.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Theory-guided Design of Refractory MPEAs for High-Temperature, Harsh-Service Conditions

Focusing on novel materials for harsh-service environments (oxidation, corrosion, and load), durability, higher operational temperature, and direct impact on power-generation technology, the goal was, using a quantitative theory-guided design approach integrated with high-throughput synthesis and characterization for validation, to accelerate by 50% the development of high temperature, refractory-based multi-principal element alloys (MPEAs) materials platforms (with co-designed oxidation-resistant, self-healing coatings) that demonstrate phase-stable operation with desired properties at 10-20% higher temperatures in oxidizing environments over state-ofthe- art systems (like Ni-stainless steels, i.e., Haynes 282 – used in critical gas turbine applications, and refractory TZM, i.e., molybdenum-rich Mo99.4-Ti0.5-Zr0.08-C0.02 in wt%). Notably, refractory MPEAs may achieve higher operational temperatures with superior creep strength and offer 50-100% larger thermal conductivity (140-170 W/m-K) than Ni-based systems, potentially eliminating active cooling, reducing system weight, complexity, and cost. Achieving this goal addresses DOE material challenges in energy generation and efficiency (higher-temperature operation), reduced lifecycle energy (waste-heat recovery), and accelerating materials development in support of AMO’s Strategic Plan and QTR goals. DOE’s Advanced Manufacturing Office (AMO) goal of reducing industrial energy intensity and GHG emissions is addressed by development of coated refractory MPEAs exhibiting 20%+ higher operational temperature (direct increase of Carnot efficiency), higher melting temperatures (better phase stability), superior creep strength (better lifetime with creep rate lower by factor of 10), larger (50-100%) thermal conductivity (improved cooling without active cooling), reduced complexity (single-phase alloys), self-healing coating (reliable oxidation-resistance) and cost.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Cooperative Research and Development Agreement among Ames Laboratory; NexTech Materials, Ltd. dba Nexceris; and National Energy Technology Laboratory [Abstract]

The CRADA focuses on pressurized testing of Nexceris solid oxide fuel cell (SOFC) stacks in a hybrid configuration with a recuperated gas turbine with the ultimate goal of demonstrating efficiencies in excess of 70% (LHV NG). NETL’s cyber-physical approach will be used to develop and test control strategies before installing the Nexceris SOFC stacks to maximize the chances of success. A successful test will represent a demonstration of the Nexceris stack to endure pressures associated with hybrid operation and the first public demonstration of automated hybrid SOFC/GT technology.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Creation of Multiple Effect Evaporator and Combined Cycle Modelica Modules, and Optimization of Potable Water Generation from Saltwater Sources (Final Technical Report)

Modelica models for a Heat Recovery Steam Generator (HRSG) and Multiple Effect Evaporator have been developed. These models have been validated against results from literature and from an actual cogeneration system on the campus of NC State University. The models are capable of connecting to other components to create multi-input, multi-output energy systems with storage, also known as integrated energy systems. An existing 35 MW gas turbine model is connected to the HRSG model created for this project to produce 9 bar steam. The high pressure steam feeds a backpressure steam turbine from the library to generate additional electric power. 2 bar steam leaves the turbine to supply an 8 effect MEE to generate water for a community. As part of the effort, three research papers were submitted (two published in ANS Proceedings and one submitted to Applied Energy).

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2024

Abstract for CRADA between National Energy Technology Laboratory and TOPTICA Photonics, Inc.

The National Energy Technology Laboratory (NETL) and Toptica Photonics (Participant) will collaborate to demonstrate the application of a frequency-comb laser (dual-comb spectroscopy) in an optically accessible rotating detonation engine (RDE). RDEs are a next-generation energy conversion technology which are well-suited to hydrogen usage and have the potential to significantly increase the efficiency of gas turbine engine power cycles. However, critical information is needed about the high temperature and pressure detonation wave, which represents an extremely challenging diagnostic environment. Dual-comb spectroscopy can be used to characterize the pressure-broadened IR absorption features at MHz rates, providing information not possible with conventional tunable diode laser (TDL) technologies. This collaboration will, for the first time, demonstrate application of dual-comb spectroscopy within the combustion annulus of a hydrogen-air RDE. If successful, the data generated will help to accelerate commercialization of RDE technologies in support of decarbonizing our nation’s energy sector.

08 HYDROGEN↗
DOE OSTI2023

High‐Throughput Computational Guided Development of Refractory Complex Concentrated Alloys‐based Composite

ULTIMATE is a leading-edge DOE program to develop ultrahigh temperature materials for gas turbine use in the aviation and power generation industries. This team, headquartered at West Virginia University and including collaborators from the National Energy Technology Laboratory and Advanced Manufacturing LLC, has developed a new class of ultra-high temperature Refractory Complex Concentrated Alloys-based Composites (RCCC) for high temperature applications such as combustion turbines used in the aerospace and energy industries. The RCCC consist of Refractory Complex Concentrated Alloys (RCCA) mixed with particles of Refractory High Entropy Carbides, to increase RCCA strength to withstand extreme conditions. These new materials optimize the balance among strength, creep (deformation), density, and stability at 1300 °C (2372 °F), while maintaining ductility once the alloy cools to room temperature. The research team has developed advanced manufacturing processes using the pulsed electric current and laser 3D printing to produce test coupons of these materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

IMPACT: Design of Integrated Multiphysics Producible Additive Components for Turbomachinery

The overall objective of the IMPACT program was to enable a dramatic reduction in design maturation time for an additive hot-section turbomachinery component through the following: • A fast crack-risk producibility surrogate model generated from machine learning applied to additive process simulation data generated via exascale computing, • Linking this surrogate model to multi-physics topology optimization (TO) to enable the creation of producible, near-optimal structural/thermal designs for additive hot-section components, • Maturing this toolset to reduce hot-section component design-for-manufacturing iterations by a large fraction, and eventually, • Using these tools to develop more efficient gas turbines in much shorter design cycle times.

42 ENGINEERING↗