Search NASA⌕ Search

SEARCH · Search NASA

Results for “TWO-DIMENSIONAL SYSTEMS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1955

Full-scale-wind-tunnel Tests of a 35 Degree Sweptback Wing Airplane with High-velocity Blowing over the Training-edge Flaps

A wind-tunnel investigation was made to determine the effects of ejecting high-velocity air near the leading edge of plain trailing-edge flaps on a 35 degree sweptback wing. The tests were made with flap deflections from 45 degrees to 85 degrees and with pressure ratios across the flap nozzles from sub-critical up to 2.9. A limited study of the effects of nozzle location and configuration on the efficiency of the flap was made. Measurements of the lift, drag, and pitching moment were made for Reynolds numbers from 5.8 to 10.1x10(6). Measurements were also made of the weight rate of flow, pressure, and temperature of the air supplied to the flap nozzles.The results show that blowing on the deflected flap produced large flap lift increments. The amount of air required to prevent flow separation on the flap was significantly less than that estimated from published two-dimensional data. When the amount of air ejected over the flap was just sufficient to prevent flow separation, the lift increment obtained agreed well with linear inviscid fluid theory up to flap deflections of 60 degrees. The flap lift increment at 85 degrees flap deflection was about 80 percent of that predicted theoretically.With larger amounts of air blown over the flap, these lift increments could be significantly increased. It was found that the performance of the flap was relatively insensitive to the location of the flap nozzle, to spacers in the nozzle, and to flow disturbances such as those caused by leading-edge slats or discontinuities on the wing or flap surfaces. Analysis of the results indicated that installation of this system on an F-86 airplane is feasible.

Kelley, Mark W↗
NASA NTRS1973

Study of exothermic processes in shock ignited gases by the use of laser shear interferometry

Report on measurements of maximum exothermic power pulses attainable from a given chemical system. Experimental tests involved the use of a shock tube technique whereby the exothermic process of combustion was controlled by reflected shock, so that it occurred under virtually inviscid flow conditions, while the measurements were performed at a resolution commensurate with the actual rate of chemical reaction. Experimental observations were made by means of a novel method of laser shear interferometry - a cross-breed between holography and the conventional means for measuring refractive index fields, in that, on one hand, it was based on the exploitation of the phase coherence of the laser light beam, recording first a diffraction image of the wave fronts which, for the desired final result, had to be optically reconstructed, and, on the other, it yielded eventually either two-dimensional interferograms or schlieren photographs of the observed phenomena.

Meyer, J. W.↗
NASA NTRS1975

Advances in Application of Fast Semidirect Computational Methods in Transonic Flow

This paper is intended as a review and summary of the advances made in a recently developed approach for rapid numerical solution of the equations of inviscid transonic aerodynamics. The investigation has been limited to two-dimensional, steady, inviscid flow over airfoils in a subsonic free stream, with emphasis on development of a rapid computational technique, rather than on generality of application. The approach uses finite-difference algorithms called "fast direct elliptic solvers" within an iteration scheme. "Direct" means that the entire computation field is solved at once, rather than in successive traverses over the field as in a point- or line-relaxation method. Such an iterative method is referred to as "semidirect." The iterative convergence can be faster than in other relaxation methods because changes are felt simultaneously at all points in each succeeding iteration. Direct elliptic solvers and semidirect methods have restrictions, but these are gradually being removed. Direct solvers were first developed for solving Poisson's equation on a rectangle without interior boundaries. A method to treat first-order systems, a direct Cauchy-Riemann solver has also been developed. Numerical treatment of part of a system of nonlinear equations by a Poisson solver has been reported. Also Poisson solvers in semidirect methods were used for nonseparable elliptic equations. The semidirect method was extended to the solution of a problem of mixed type, where the improved Murman-Cole transonic small-disturbance difference equations were solved. A slightly supercritical flow over a biconvex airfoil was treated successfully, but the iterations did not converge for more strongly supercritical conditions In another work the addition of terms ot both sides of the difference equations stabilized the iteration for supercritical conditions with large supersonic zones. For this, the Cauchy-Riemann solver was revised to incl,ude the needed terms. Most recently, the evaluation of parameters for rapid convergence and comparisons, with Murman's line-relaxation method was described. The method was extended to full second order accuracy in a fully conservative formulation in another work.

Martin, E. Dale↗
NASA NTRS1972

Automated cloud tracking using precisely aligned digital ATS pictures.

Discussion of the interactive man-computer system (WIMDCO) for measuring cloud motion from ATS pictures. The multipicture model of ATS navigation is used for consecutive ATS digital picture alignment to provide the required precision in cloud motion measurements by automated tracking techniques. Cloud motion is measured by tracking clouds between two digital pictures with the aid of two-dimensional cross correlation analysis. The fast Fourier transform method and other programming techniques are used for time and cost minimization. Cloud motion vectors were computed over three time intervals in July, 1969. The EW and NS components were reproducible within roughly 2 knots.

Smith, E. A.↗
NASA NTRS1972

Optimization of thermal protection systems for the space shuttle vehicle. Volume 1: Final report

A study performed to continue development of computational techniques for the Space Shuttle Thermal Protection System is reported. The resulting computer code was used to perform some additional optimization studies on several TPS configurations. The program was developed in Fortran 4 for the CDC 6400, and it was converted to Fortran 5 to be used for the Univac 1108. The computational methodology is developed in modular fashion to facilitate changes and updating of the techniques and to allow overlaying the computer code to fit into approximately 131,000 octal words of core storage. The program logic involves subroutines which handle input and output of information between computer and user, thermodynamic stress, dynamic, and weight/estimate analyses of a variety of panel configurations. These include metallic, ablative, RSI (with and without an underlying phase change material), and a thermodynamic analysis only of carbon-carbon systems applied to the leading edge and flat cover panels. Two different thermodynamic analyses are used. The first is a two-dimensional, explicit precedure with variable time steps which is used to describe the behavior of metallic and carbon-carbon leading edges. The second is a one-dimensional implicity technique used to predict temperature in the charring ablator and the noncharring RSI. The latter analysis is performed simply by suppressing the chemical reactions and pyrolysis of the TPS material.

Source record↗
NASA NTRS1975

Recent developments in density, temperature and momentum fluctuation measurement

Attention is drawn to recent advancements in the fluctuating line-reversal temperature measurement, the development of the two-dimensional drag-sensing probe into a three-dimensional drag-sensing probe, and the fluctuating density gradient cross beam Schlieren technique. An experimental apparatus is explained whereby the temperature fluctuation in a pulsating air-fuel ratio Bunsen burner is measured by means of sodium D-line reversal methods with a new photoelectric circuit to obtain both fluctuating and mean temperature data. The three-D drag probe is made possible by a newly invented differential and total magnetic sensing system that separates signals due to three orthogonal movements so that the vectorial momentum fluctuation can be measured. In the case of the Schlieren technique, the effect of anisotropic density gradients with respect to the angle between the polarization plane and the knife edge of a laser Schlieren system is studied.

Battle, T. M.↗
NASA NTRS1975

Structure of turbulent jets and wakes

The structure of two-dimensional turbulent jets and wakes is studied using two eddy viscosity models. The turbulent energy equation is used together with the mean momentum equations, and the system is closed by introducing eddy coefficients. The fine structure turbulence is obtained by applying proper boundary conditions at the mean turbulent interface position. The results, after a second averaging process, are compared with available experimental data.

Wang, F. C.↗
NASA NTRS1975

Calculation of three-dimensional compressible laminar and turbulent boundary layers. Calculation of three-dimensional compressible boundary layers on arbitrary wings

A very general method for calculating compressible three-dimensional laminar and turbulent boundary layers on arbitrary wings is described. The method utilizes a nonorthogonal coordinate system for the boundary-layer calculations and includes a geometry package that represents the wing analytically. In the calculations all the geometric parameters of the coordinate system are accounted for. The Reynolds shear-stress terms are modeled by an eddy-viscosity formulation developed by Cebeci. The governing equations are solved by a very efficient two-point finite-difference method used earlier by Keller and Cebeci for two-dimensional flows and later by Cebeci for three-dimensional flows.

Cebeci, T.↗
NASA NTRS1975

STOL aircraft transient ground effects. Part 1: Fundamental analytical study

The first phases of a fundamental analytical study of STOL ground effects were presented. Ground effects were studied in two dimensions to establish the importance of nonlinear effects, to examine transient aspects of ascent and descent near the ground, and to study the modelling of the jet impingement on the ground. Powered lift system effects were treated using the jet-flap analogy. The status of a three-dimensional jet-wing ground effect method was presented. It was shown, for two-dimensional unblown airfoils, that the transient effects are small and are primarily due to airfoil/freestream/ground orientation rather than to unsteady effects. The three-dimensional study showed phenomena similar to the two-dimensional results. For unblown wings, the wing/freestream/ground orientation effects were shown to be of the same order of magnitude as for unblown airfoils. This may be used to study the nonplanar, nonlinear, jet-wing ground effect.

Goldhammer, M. I.↗
NASA NTRS1975

Flutter analysis of two parallel elastically coupled flat plates

Flutter of two parallel elastically coupled flat plates was investigated analytically. A closed-form solution including both aerodynamic and structural damping is presented for flutter of flat orthotropic plates coupled by an elastic medium. Both plates are simply supported along the side edges but are supported by deflectional, rotational, and torsional springs of arbitrary stiffness at the leading and trailing edges. Two-dimensional quasi-steady aerodynamics was utilized in the solution. Since the large number of variables present in the problem precludes extensive parametric studies, results are presented to indicate the basic flutter characteristics of coupled two-plate systems and to assess the validity of previously published modal solutions for similar problems.

Shore, C. P.↗
NASA NTRS1975

Silica heat shield sizing

The sensitivity of silica heat shield requirements to gap width, tile edge radius, and heat transfer distribution within tile gaps was investigated. A two-dimensional thermal model was modified and used to determine the effect of two dimensional heat transfer distributions at high temperature reusable surface insulation edges on shuttle thermal protection system (TPS) requirements. The sensitivity of TPS requirements to coating thickness, emissivity, substructure thickness, and changes in gap heating for several locations on shuttle was also studied. An inverse solution technique was applied to temperature data obtained in the Ames 20 MW turbulent duct in order to examine the effect of tile edge radius on TPS requirements. The derived heating values were then used to predict TPS requirements. Results show that increasing tile radius reduces TPS requirements.

Ebbesmeyer, L. H.↗
NASA NTRS1976

Improved interactive calculation procedure for supersonic flows

An interactive numerical procedure has been developed for supersonic viscous flows (either two-dimensional or axisymmetric configurations). The flow field is divided into two regions: (1) an inner region which is highly viscous and mostly subsonic, and (2) an outer region where the flow is supersonic and in which viscous effects are small, but not negligible. This paper presents a detailed description of: I. Outer Region - numerical solution obtained by applying the method of characteristics to a system of equations which includes viscous and conduction transport terms only normal to the streamlines; II. Inner Region - treated by a system of equations of the boundary-layer type that includes higher order effects, such as longitudinal and transverse curvature and normal pressure gradients (equations are coupled and solved simultaneously in physical coordinates, using an implicit finite-difference scheme); III. Interactive Procedure - in the interaction mode, the two regions are coupled iteratively along a matching line, where the Mach number is of the order of 1.2.

Tassa, Y.↗
NASA NTRS1956

Performance of variable two-dimensional inlet designed for engine-inlet matching I : performance at design Mach number of 3.07

The inlet was investigated with both a two-oblique-shock and an isentropic compression ramp. Provisions for a variety of bypass systems were incorporated and none decreased pressure recovery by more than about 1 percent. By utilizing throat boundary-layer control, critical pressure recoveries of 64 and 70 percent were obtained with the two-shock and isentropic ramps, respectively. Diffuser-exit air distortion was about 5 percent at critical operation Theoretical cowl pressure drag was equal to about 10 percent of the net thrust of an assumed engine.

Beheim, M A↗
NASA NTRS1939

A theoretical study of the moment on a body in a compressible fluid

The extension to a compressible fluid of Lagally's theorem on the moment on a body in an incompressible fluid and Poggi's method of treating the flow of compressible fluids are employed for the determination of the effect of compressibility on the moment of an arbitrary body. Only the case of the two-dimensional subsonic flow of an ideal compressible fluid is considered. As examples of the application of the general theory, two well-known systems of profiles are treated; namely the elliptic profile and the symmetrical Joukowski profiles with sharp trailing edges. The effect of compressibility on the position of the center of pressure is also discussed. Several numerical examples of both the elliptic and the Joukowski profiles are given.

Kaplan, Carl↗
NASA NTRS1938

Wind-tunnel Investigations on Flexural-torsional Wing Flutter

For the purpose of testing the theory of an oscillating airfoil of two degrees of freedom, a wing was mounted in the wind tunnel between two walls in such a manner that it could execute vertical (flexural) oscillations as well as torsional oscillations about an arbitrary axis parallel to the span. It was possible to vary the inertia and elasticity parameters and also to increase artificially the negligibly small natural damping of the system. The oscillations were recorded to a strongly magnified scale. The experimentally determined critical (or flutter) velocities fully agree with the theoretical ones of Wagner and Kussner within the limits of computational and measuring accuracy. An extremely narrow wing without end walls (three dimensional problem) showed the same oscillations as one with end walls (two-dimensional problem).

Voigt, H↗
NASA NTRS1973

On Lidar Sounding of the Atmosphere to Estimate Static and Dynamic Characteristics of Aerosol Inhomogeneities

1. A possible application of intensity fluctuations of a pulse light signal reflected by atmospheric aerosols is analyzed by the correlation method to evaluate static (medium sizes, shape) and dynamic (speed and direction of movement, lifetime) characteristics of aerosol inhomogeneities. The aerosol inhomogeneities are assumed to be expanded, pressed, disintegrated and originated constantly in accordance with random laws, the set of inhomogeneities as a whole traveling together with air masses and having predominant movement in wind direction. It is shown that the characteristics of aerosol inhomogeneities considered can be expressed by the coefficients of the correlation function expansion of the reflected signal fluctuation intensity in Tailor series. 2/ Correlation systems for evaluating static and dynamic characteristics of driving objects can be divided into two types according to the kind and quantity of used information: the systems with coordinates of the information removal "points" to be fixed in space, and the systems with a parallel simultaneous information removal at discrete moments of time. The systems for determination of wind direction considered in are the examples of the first type system. However, the operating information removal for two points is insufficient to estimate completely static and dynamic characteristics of inhomogenities, their quantity ought to be increased up to three of them for two-dimensional problem and up to four of them for three-dimensional problem as it is usually done in the ionospheric studies. The second type systems are used for the investigation of a medium shape and speed of the clouds according to photographs made from satellites. These systems are also used for solution of navigation problems. The use of optical quantum generators with a scanning beam is seen to increase greatly the working information removal in comparison with the first type systems. Nevertheless, scanning rate is not sufficient sometimes in order· to consider a general picture of aerosol inhomogeneities to be stationary. In this connection the use of the systems of second type treatment becomes a matter of essential difficulty. 3. Aerosol inhomogeneities simulation has been carried out on the basis of the digital computer experiments with the aim of estimating static and dynamic characteristics of inhomogeneities by an optical beam in the atmosphere at different scanning procedures. The dependence of determination accuracy of these characteristics on the type of chosen laws of aerosol particle distribution in the atmosphere, the parameters of inhomogeneities geometry, their speed and the law of scanning have been obtained.

Zuev, V. E.↗