Search NASA⌕ Search

SEARCH · Search NASA

Results for “Tabulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

ECAR-1943 AGC-1 INDIVIDUAL SPECIMEN FLUENCE, TEMPERATURE, AND LOAD CALCULATION AND TABULATION

This ECAR calculates the fluence and temperature of the AGC-1 specimens as they change elevation through the course of the experiment. The specimen elevation varies as the specimen stack shrinks due to irradiation and load induced creep. The compressed specimen stacks (S-1 thru S-6) have a graphite pushrod that applies a gas cylinder load. The top of the pushrod position is measured and recorded in the NGNP Data Management and Analysis System (NDMAS). The bottom of each of these compressed stacks is supported by the lower specimen holder which also shrinks as a result of irradiation and load. The specimen holder post-irradiation length was recorded during post-irradiation examination (PIE). Assuming the specimen holder shrinkage is linear with respect to the fluence received, the position of the top of the specimen holder can be calculated with respect to reactor integrated power. Assuming that individual specimen shrinkage is proportional to the fluence received, and that the shrinkage behavior is similar in all the specimens, the individual specimen position can be calculated.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

An equivalent dissipation rate model for capturing history effects in non-premixed flames

The effects of strain rate history on turbulent flames have been studied in the. past decades with 1D counter flow diffusion flame (CFDF) configurations subjected to oscillating strain rates. In this work, these unsteady effects are studied for complex hydrocarbon fuel surrogates at engine relevant conditions with unsteady strain rates experienced by flamelets in a typical spray flame. Tabulated combustion models are based on a steady scalar dissipation rate (SDR) assumption and hence cannot capture these unsteady strain effects; even though they can capture the unsteady chemistry. In this work, 1D CFDF with varying strain rates are simulated using two different modeling approaches: steady SDR assumption and unsteady flamelet model. Comparative studies show that the history effects due to unsteady SDR are directly proportional to the temporal gradient of the SDR. A new equivalent SDR model based on the history of a flamelet is proposed. An averaging procedure is constructed such that the most recent histories are given higher weights. This equivalent SDR is then used with the steady SDR assumption in 1D flamelets. Results show a good agreement between tabulated flamelet solution and the unsteady flamelet results. This equivalent SDR concept is further implemented and compared against 3D spray flames (Engine Combustion Network Spray A). Tabulated models based on steady SDR assumption under-predict autoignition and flame lift-off when compared with an unsteady Representative Interactive Flamelet (RIF) model. However, equivalent SDR model coupled with the tabulated model predicted autoignition and flame lift-off very close to those reported by the RIF model. This model is further validated for a range of injection pressures for Spray A flames. The new modeling framework now enables tabulated models with significantly lower computational cost to account for unsteady history effects. (C) 2016 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Kundu, Prithwish↗

Standard States for Adsorption on Solid Surfaces: 2D Gases, Surface Liquids, and Langmuir Adsorbates

Standard states are utilized to compare thermodynamic data obtained from different experiments and calculations, and this ability to compare thermodynamic data plays an important role in science and society. For molecules adsorbed on surfaces, there are currently no universally accepted standard states. Here, standard states are proposed for the different types of molecular adsorbate phases, with the intent to enable physical insight to be gained by tabulating experimental/calculated values, such that comparison between different systems and existing societal tabulations of chemical standard state tabulated values can be done directly. A “density based” standard state is proposed for 2D gases, and a “relative coverage based” standard state is proposed for immobile adsorbates and nonislanding 2D liquids. These units are chosen based upon the units which the activity depends on. The standard states recommended here are chosen due to the entropies associated with them, such that physical insight can be gained by direct comparison to existing tabulated data. For 2D gases adsorbed on solid surfaces, the recommended standard state is σ° = 1.39 × 10 –7 mol m –2 . For immobile adsorbates and nonislanding liquid states on solid surfaces, the recommended standard state is θ A ° = 0.5 (which implies a standard state for the surface sites of of θ S ° = 1 – θ A ° = 0.5). With the standard states recommended here, tabulated values at a common temperature are expected to display the following approximate hierarchy for decreasing entropy: 3D gas > 2D gas > liquid > surface liquid > solid > lattice confined. Lastly, recommended standard states are also provided in the Supporting Information for cases with dissociative adsorption.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Milestones for Selection, Characterization, and Analysis of the Performance of a Repository for Spent Nuclear Fuel and High-Level Radioactive Waste at Yucca Mountain.

This report presents a concise history in tabular form of events leading up to site identification in 1978, site selection in 1987, subsequent characterization, and ongoing analysis through 2009 of the performance of a repository for spent nuclear fuel and high - level radioactive waste at Yucca Mountain in southern Nevada. The tabulated events generally occurred in five periods: (1) commitment to mined geologic disposal and identification of sites; (2) site selection and analysis, based on regional geologic characterization through literature and analogous data; (3) feasibility analysis demonstrating calculation procedures and importance of system components, based on rough measures of performance using surface exploration, waste process knowledge, and general laboratory experiments; (4) suitability analysis demonstrating viability of disposal system, based on environment - specific laboratory experiments, in - situ experiments, and underground disposal system characterization; and (5) compliance analysis, based on completed site - specific characterization . The current sixth period beyond 2010 represents a new effort to set waste management policy in the United States. Because the relationship is important to understanding the evolution of the Yucca Mountain Project , the tabulation also shows the interaction between the policy realm and technical realm using four broad categories of events : (a) Regulatory requirements and related federal policy in laws and court decisions, (c) Presidential and agency directives, (c) technical milestones of implementing institutions, and (d) critiques of the Yucca Mountain Project and pertinent national and world events related to nuclear energy and radioactive waste. Preface The historical progression of technical milestones for the Yucca Mountain Project was originally developed for 10 journal articles in a special issue of Reliability Engineering System Safety on the performance assessment for the Yucca Mountain license application [1-10]. The listing of mile stones, a distinct feature of those articles, has been collected and tabulated here. A lthough a brief description is presented here (based on the summaries in the 10 journal articles), the emphasis remains on the tabulation because of its usefulness in providing a comprehensive but concise history of the Yucca Mountain Project. The tabulation presented here is more elaborate than originally presented in that many of the interactions that occurred between the technical realm and policy realm can be depicted in separate columns. The usefulness of the milestones table is due in part to L.A. Connolly, for editorial and reference support, and S.K. Best, Raytheon, and L. Mays, Sandia National Laboratories (SNL), for illustration support. Reviewers P.N. Swift, SNL, and K. Gupta, University of Oklahoma, helped improve the discussion. The historical perspective presented is that of the author and is not necessarily held by reviewers, Sandia National Laboratories , and the US Department of Energy. As a historic perspective, the author is reporting on the work of others; however, any interpretative error s of the documentation are those of the author alone. The characterization and modeling of the Yucca Mountain disposal system required numerous participants with expertise in many areas of science and technology, as evident from the extensive reference list. Their diligent efforts are generally acknowledged here and through the many references to their impressive work, but the 10 journal articles acknowledge by name many of the numerous participants that contributed to the Yucca Mountain Project .

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A priori filtered chemical source term modeling for LES of high Karlovitz number premixed flames

Assumptions behind closure models for the filtered source term are studied a priori using results from DNS of turbulent n-heptane/air premixed flames at varying Karlovitz numbers. Simulations with both detailed chemistry and tabulated chemistry, as well as unity and non-unity Lewis numbers, are used to determine if finite-rate chemistry and differential diffusion effects affect the filtered chemical source terms. While the unfiltered source term shows large fluctuations, the filtered source terms from detailed chemistry and tabulated chemistry are in good agreement at sufficiently large filter widths (Δ ≳ l F ). Using the concept of optimal estimators, it is shown that a tabulation approach using the filtered progress variable and its variance can predict accurately the filtered chemical source terms. Finally, the filtered source terms from the DNS are compared to predictions from two commonly assumed sub-filter probability density function models. Both models show deviations from the filtered DNS source terms but predict accurately the mean turbulent flame speed. In conclusion, the results illustrate the potential of using simple tabulated chemistry approaches based on presumed PDFs for LES of premixed flames in the thin and distributed reaction zones regimes.

33 ADVANCED PROPULSION SYSTEMS↗

Application of deep artificial neural networks to multi-dimensional flamelet libraries and spray flames

The “curse of dimensionality” has limited the applicability and expansion of tabulated combustion models. While the tabulated flamelet model and other multi-dimensional manifold approaches have shown predictive capability, the associated tabulation involves the storage of large lookup tables, requiring large memory as well as multi-dimensional interpolation subroutines, all implemented during runtime. As such, this work investigates the use of deep artificial neural networks to replace lookup tables in order to reduce the memory footprint and increase the computational speed of tabulated flamelets and related approaches. Specifically, different strategic approaches to training the artificial neural network models are explored and a grouped multi-target artificial neural network is introduced, which takes advantage of the ability of artificial neural networks to map an input space to multiple targets by classifying the species based on their correlation to one another. The grouped multi-target artificial neural network approach is validated by applying it to an n-dodecane spray flame using conditions of the Spray A flame from the Engine Combustion Network and comparing global flame characteristics for different ambient conditions using a well-established large-eddy simulation framework. The same framework is then extended to the simulations of methyl decanoate combustion in a compression ignition engine. The validation studies show that the grouped multi-target artificial neural networks are able to accurately capture flame liftoff, autoignition, two-stage heat release and other quantitative trends over a range of conditions. The use of neural networks in conjunction with the grouping mechanism as performed in the grouped multi-target artificial neural network produces a significant reduction in the memory footprint and computational costs for the code and, thus, widens the operating envelope for higher fidelity engine simulations with detailed mechanisms.

97 MATHEMATICS AND COMPUTING↗

The generation of arbitrary order, non-classical, Gauss-type quadrature for transport applications

A method is presented, based upon the Stieltjes method (1884), for the determination of non-classical Gauss-type quadrature rules, and the associated sets of abscissae and weights. The method is then used to generate a number of quadrature sets, to arbitrary order, which are primarily aimed at deterministic transport calculations. The quadrature rules and sets detailed include arbitrary order reproductions of those presented by Abu-Shumays in [4,8] (known as the QR sets, but labelled QRA here), in addition to a number of new rules and associated sets; these are generated in a similar way, and we label them the QRS quadrature sets. The method presented here shifts the inherent difficulty (encountered by Abu-Shumays) associated with solving the non-linear moment equations, particular to the required quadrature rule, to one of the determination of non-classical weight functions and the subsequent calculation of various associated inner products. Once a quadrature rule has been written in a standard form, with an associated weight function having been identified, the calculation of the required inner products is achieved using specific variable transformations, in addition to the use of rapid, highly accurate quadrature suited to this purpose. The associated non-classical Gauss quadrature sets can then be determined, and this can be done to any order very rapidly. In this paper, instead of listing weights and abscissae for the different quadrature sets detailed (of which there are a number), the MATLAB code written to generate them is included as Appendix D. The accuracy and efficacy (in a transport setting) of the quadrature sets presented is not tested in this paper (although the accuracy of the QRA quadrature sets has been studied in [12,13]), but comparisons to tabulated results listed in [8] are made. When comparisons are made with one of the azimuthal QRA sets detailed in [8], the inherent difficulty in the method of generation, used there, becomes apparent, with the highest order tabulated sets showing unexpected anomalies. Although not in an actual transport setting, the accuracy of the sets presented here is assessed to some extent, by using them to approximate integrals (over an octant of the unit sphere) of various high order spherical harmonics. When this is done, errors in the tabulated QRA sets present themselves at the highest tabulated orders, whilst combinations of the new QRS quadrature sets offer some improvements in accuracy over the original QRA sets. Finally, in order to offer a quick, visual understanding of the various quadrature sets presented, when combined to give product sets for the purposes of integrating functions confined to the surface of a sphere, three-dimensional representations of points located on an octant of the unit sphere (as in [8,12]) are shown.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

An a priori evaluation of a principal component and artificial neural network based combustion model in diesel engine conditions

A principal component analysis (PCA) and artificial neural network (ANN) based chemistry tabulation approach is presented. ANNs are used to map the thermochemical state onto a low-dimensional manifold consisting of five control variables that have been identified using PCA. Three canonical configurations are considered to train the PCA-ANN model: a series of homogeneous reactors, a nonpremixed flamelet, and a two-dimensional lifted flame. The performance of the model in predicting the thermochemical manifold of a spatially-developing turbulent jet flame in diesel engine thermochemical conditions is a priori evaluated using direct numerical simulation (DNS) data. The PCA-ANN approach is compared with a conventional tabulation approach (tabulation using ad hoc defined control variables and linear interpolation). The PCA-ANN model provides higher accuracy and requires several orders of magnitude less memory. Here, these observations indicate that the PCA-ANN model is superior for chemistry tabulation, especially for modelling complex chemistries that present multiple combustion modes as observed in diesel combustion. The performance of the PCA-ANN model is then compared to the optimal estimator, i.e. the conditional mean from the DNS. The results indicate that the PCA-ANN model gives high prediction accuracy, comparable to the optimal estimator, especially for major species and the thermophysical properties. Higher errors are observed for the minor species and reaction rate predictions when compared to the optimal estimator. It is shown that the prediction of minor species and reaction rates can be improved by using training data that exhibits a variation of parameters as observed in the turbulent flame. The output of the ANN is analysed to assess mass conservation. It is observed that the ANN incurs a mean absolute error of 0.05% in mass conservation. Furthermore, it is demonstrated that this error can be reduced by modifying the cost function of the ANN to penalise for deviation from mass conservation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

How negative feedback and the ambient environment limit the influence of recombination in common envelope evolution

ABSTRACT We perform 3D hydrodynamical simulations to study recombination and ionization during the common envelope (CE) phase of binary evolution, and develop techniques to track the ionic transitions in time and space. We simulate the interaction of a $2\, \mathrm{M_\odot }$ red giant branch primary and a $1\, \mathrm{M_\odot }$ companion modelled as a particle. We compare a run employing a tabulated equation of state (EOS) that accounts for ionization and recombination, with a run employing an ideal gas EOS. During the first half of the simulations, ∼15 per cent more mass is unbound in the tabulated EOS run due to the release of recombination energy, but by simulation end the difference has become negligible. We explain this as being a consequence of (i) the tabulated EOS run experiences a shallower inspiral and hence smaller orbital energy release at late times because recombination energy release expands the envelope and reduces drag, and (ii) collision and mixing between expanding envelope gas, ejecta and circumstellar ambient gas assists in unbinding the envelope, but does so less efficiently in the tabulated EOS run where some of the energy transferred to bound envelope gas is used for ionization. The rate of mass unbinding is approximately constant in the last half of the simulations and the orbital separation steadily decreases at late times. A simple linear extrapolation predicts a CE phase duration of ${\sim}2\, {\rm yr}$, after which the envelope would be unbound.

79 ASTRONOMY AND ASTROPHYSICS↗

Oak Ridge National Laboratory Technical Input for the Nuclear Regulatory Commission Review of the 2017 Edition of ASME Section III, Division 5, ‘High Temperature Reactors’

To assist the Nuclear Regulatory Commission in its decision making on endorsement of the American Society for Mechanical Engineers Boiler and Pressure Vessel Code Section III, Division 5 (2017 Edition) for development of advanced non-light water reactors, the following Division 5 portions were reviewed: Article HBB-2000 Material; Article HCB-2000 Material; Article HGB-2000 Material; Mandatory Appendix HBB-I-14 Tables and Figures; and, Nonmandatory Appendix HBB-U Guidelines for Restricted Material Specifications to Improve Performance in Certain Service Applications. In addition to the 2017 Edition, the same parts of the 2019 Edition have also been reviewed as indicated in various sections of the report. This review was conducted by a collaboration of national laboratory and private sector participants with significant industrial experience, including some heavy lifting and deep diving from Clarus Consulting, LLC., all intended to achieve an objective, independent, and practical perspective. The report provides recommendations, descriptions of the evaluation methods, and the source references for the data used. To build confidence required for endorsement of the Code, this review was conducted as a verification and validation of the above Code contents. The objective of verification is to ensure that the Code is free of error – direct or implied; contains the information needed for its use, including proper coverage of the Code-specified materials for the intended application, and completeness and adequacy of references to other portions of the Code. The objective of validation is to authenticate that the Code tabulations and graphs represent design inputs consistent with what are determined using rules and methods specified by the Code. The authentication process used data that were assembled and/or generated independent of Code development, while the methods of analysis followed Code-specified methods where appropriate. The designated portions for this review cover the five alloys codified for high temperature reactor applications in Division 5, i.e. 316 SS, 304 SS, 800H, 2¼Cr-1Mo, and 9Cr-1Mo-V, regarding their general requirements, permitted specifications and design stress intensity values for pressure-retaining applications, deterioration in service, fatigue acceptance test, permissible weld materials, tensile and yield strength, expected minimum stress-to-rupture values (including for Alloy 718), weld stress rupture factors, permissible materials for bolting use, and restricted specifications in certain service applications. Additionally, stress intensity values for bolting materials including 316 SS, 304 SS and alloy 718 were reviewed. Analysis and discussion are also provided on contents outside of these designated Code portions where it was deemed relevant and necessary to develop a technically sound understanding of issues relating to the designated portions. Due to unavailability of sufficient test data on welds during the review period, the weld stress rupture factors in Tables HBB-I-10.14A to E, which cover a total of ten tables for the five alloys welded with twenty-eight different weld metals (some with similar properties), have been deferred to a future review effort. The review identified mainly two types of issues. The first type includes instances where the Code is found factually incomplete or incorrect, such as obsolete materials specifications listings, missing tabulation of stresses for bolting. Changes to the Code are recommended in these cases. The second type of issue includes instances where the Code tabulations and graphs are found to be less conservative than the review analysis results. In these cases, recommendations are made for further review and consideration where the difference in conservatism exceeds 10%, which is our threshold for questioning technical adequacy, meriting a risk assessment by the Nuclear Regulatory Commission and/or reactor designers. It is noted that this effort has been executed using all available data and established methods of analysis, including methods and criteria specified and used by the Code. As such, the findings that are presented in quantitative detail, in a format for convenient comparison with the Code, and with identification of where further review is recommended, should provide a sound technical basis for decisions about quantifying the implications of the reduced design margins and technical adequacy/inadequacy to form a basis for conditioning specific Code tabulation values on endorsement. Recommendations for specific changes to the Code, however, entail design conservatism considerations beyond the scope of this review effort, and are not made in this report.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Thermodynamic data for fifty reference elements

This report is a compilation of thermodynamic functions of 50 elements in their standard reference state. The functions are C(sub p)(sup 0), (H(sup 0)(T) - H(sup 0)(0)), S(sup 0)(T), and -(G(sup 0)(T) - H(sup 0)(O)) for the elements Ag, Al, Ar, B, Ba, Be, Br2, C, Ca, Cd, Cl2, Co, Cr, Cs, Cu, F2, Fe, Ge, H2, He, Hg, I2, K, Kr, Li, Mg, Mn, Mo, N2, Na, Nb, Ne, Ni, O2, P, Pb, Rb, S, Si, Sn, Sr, Ta, Th, Ti, U, V, W, Xe, Zn, and Zr. Deuterium D2 and electron gas e(sup -) are also included. The data are tabulated as functions of temperature as well as given in the form of least-squares coefficients for two functional forms for C(sub p)(sup 0) with integration constants for enthalpy and entropy. One functional form for C(sub p)(sup 0) is a fourth-order polynomial and the other has two additional terms, one with T(exp -1) and the other with T(exp -2). The gases Ar, D2, e(sup -), H2, He, Kr, N2, Ne, O2, and Xe are tabulated for temperatures from 100 to 20,000 K. The remaining gases Cl2 and F2 are tabulated from 100 to 6000 K and 1000 to 6000 K. The second functional form for C(sub p)(sup 0) has an additional interval from 6000 to 20,000 K for the gases tabulated to 20,000 K. The fits are constrained so that the match at the common temperature endpoints. The temperature ranges for the condensed species vary with range of the data, phase changes, and shapes of the C(sub p)(sup 0) curves.

Mcbride, Bonnie J.↗

Thermodynamic Data for Fifty Reference Elements

This report is a compilation of thermodynamic functions of 50 elements in their reference state. The functions are: C(sup 0, sub p), {H(T)-H(sup 0)(0)}, S(sup 0)(T), and - {G(sup 0)(T) - H(sup 0)(0)} for the elements Ag, Al, Ar, B, Ba, Be, Br2, C, Ca, Cd, Cl2, Co, Cr, Cs, Cu, F2, Fe, Ge, H2, He, Hg, I2, K, Kr, Li, Mg, Mn, Mo, N2, Na, Nb, Ne, Ni, O2, P, Pb, Rb, S, Si, Sn, Sr, Th, Th, Ti, U, V, W, Xe, Zn, and Zr. Deuterium D, and electron gas e(sup -) are also included. The data are tabulated as functions of temperature as well as given in the form of least-squares coefficients for two functional forms for C(sup 0, sub p) with integration constants for enthalpy and entropy. One functional form for C(sup 0, sub p) is a fourth-order polynomial and the other has two additional terms, one with T(sup -1) and the other with T(sup -2). The gases Ar, D2, e(sup -), H2, He, Kr, N2, Ne, O2, and Xe are tabulated for temperatures from 100 to 20 000 K. The remaining gases Cl2 and F2 are tabulated from 100 to 6000 K. The polynomial functional form for C(sup 0, sub p) for all these gases is split into two temperature intervals of 200 to 1000 K and 1000 to 6000 K. The second functional form for (sup 0, sub p) has an additional interval from 6000 to 20 000 K for the gases tabulated to 20 000 K. The fits are constrained so that the properties match at the common temperature endpoints. The temperature ranges for the condensed species vary with range of the data, phase changes, and shapes of the C(sup 0, sub p) curves.

McBride, Bonnie J.↗

Computationally efficient implementation of combustion chemistry in parallel PDF calculations

In parallel calculations of combustion processes with realistic chemistry, the serial in situ adaptive tabulation (ISAT) algorithm [S.B. Pope, Computationally efficient implementation of combustion chemistry using in situ adaptive tabulation, Combustion Theory and Modelling, 1 (1997) 41-63; L. Lu, S.B. Pope, An improved algorithm for in situ adaptive tabulation, Journal of Computational Physics 228 (2009) 361-386] substantially speeds up the chemistry calculations on each processor. To improve the parallel efficiency of large ensembles of such calculations in parallel computations, in this work, the ISAT algorithm is extended to the multi-processor environment, with the aim of minimizing the wall clock time required for the whole ensemble. Parallel ISAT strategies are developed by combining the existing serial ISAT algorithm with different distribution strategies, namely purely local processing (PLP), uniformly random distribution (URAN), and preferential distribution (PREF). The distribution strategies enable the queued load redistribution of chemistry calculations among processors using message passing. They are implemented in the software x2f{sub m}pi, which is a Fortran 95 library for facilitating many parallel evaluations of a general vector function. The relative performance of the parallel ISAT strategies is investigated in different computational regimes via the PDF calculations of multiple partially stirred reactors burning methane/air mixtures. The results show that the performance of ISAT with a fixed distribution strategy strongly depends on certain computational regimes, based on how much memory is available and how much overlap exists between tabulated information on different processors. No one fixed strategy consistently achieves good performance in all the regimes. Therefore, an adaptive distribution strategy, which blends PLP, URAN and PREF, is devised and implemented. It yields consistently good performance in all regimes. In the adaptive parallel ISAT strategy, the type and extent of redistribution is determined 'on the fly' based on the prediction of future simulation time. Compared to the PLP/ISAT strategy where chemistry calculations are essentially serial, a speed-up factor of up to 30 is achieved. The study also demonstrates that the adaptive strategy has acceptable parallel scalability.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A two-equation soot-in-flamelet modeling approach applied under Spray A conditions

Soot production (including formation and oxidation) is studied in the transient, high-pressure and turbulent n-dodecane Spray A flames from the Engine Combustion Network (ECN) using computational fluid dynamics (CFD) simulations. A two-equation soot-in-flamelet modeling approach is applied within the framework of the Unsteady Flamelet Progress Variable (UFPV) model and results are validated against experimental data. Equations for soot mass fraction and soot number density derived in the mixture fraction space are solved in the context of detailed flamelet calculations. Source terms for the different steps in the soot chemistry are tabulated and incorporated in the flamelet manifold. For the reference condition, the modeling approach based on the tabulated flamelet manifold reduces the computational cost of a CFD calculation by approximately 40 times compared to a non-tabulated well-mixed (WM) modeling approach. The soot-in-flamelet approach is then extended to study the effect of ambient oxygen concentration, ambient mixture composition and ambient temperature on soot production. Results show that the modeling approach is able to capture the experimental trends for the soot volume fraction (SVF) with good quantitative agreement, especially in the soot ramp-up region.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Assessment of flamelet/progress variable methods for supersonic combustion

Tabulated chemistry models, including the flamelet/progress variable approach, have been successfully used for a variety of turbulent flame simulations. The progress variable describes the progress of reactions in a system and parameterizes a lookup table of thermochemical variables. This approach reduces the cost of simulations, transporting only one scalar (progress variable) instead of the many species mass fractions required for detailed chemistry. Originally developed for low Mach number flame simulations, recent works have focused on extensions of this approach to compressible flames, supersonic combustion, and detonations, with applications such as scramjet combustors and rotating detonation engines. Unlike low Mach simulations, compressible flow simulations require solving the energy transport equation, which is coupled to the equation of state. This leads to additional modeling challenges regarding the thermodynamics and its impact on the chemistry. The validity of modeling assumptions, for example the relationship between energy and temperature, also varies with the combustion regime. The present work provides a detailed assessment of the existing strategies for chemistry tabulation for compressible/supersonic combustion, including detonations. A priori analysis indicates that approximations which are reasonable for weakly compressible flames may break down for shock-induced combustion. Furthermore, the analysis identifies specific assumptions and approximations that do not hold for detonations, emphasizing that care must be taken when applying tabulated chemistry models outside their intended combustion regimes.

Detonations↗

Dependence of nuclear quadrupole resonance transitions on the electric field gradient asymmetry parameter for nuclides with half-integer spins

Allowed transition energies and eigenstate expansions have been calculated and tabulated in numerical form as functions of the electric field gradient asymmetry parameter for the zero field Hamiltonian of quadrupolar nuclides with I=3/2,5/2,7/2, and 9/2. These results are essential to interpret nuclear quadrupole resonance (NQR) spectra and extract accurate values of the electric field gradient tensors. Applications of NQR methods to studies of electronic structure in heavy element systems are proposed.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

SU-F-18C-10: Clinical Implementation of Radiochromic Film Based CTDI Measurements

Purpose: To evaluate accuracy and reproducibility of a radiochromic film-based protocol to measure computer tomography dose index (CTDI) as a part of annual QA on CT scanners and kV CBCT systems attached to linear accelerators. Methods: Energy dependence of Gafchromic XR-QA2(R) film model was tested over imaging beam qualities (50 – 140 kVp). Film pieces were irradiated in air to known values of air kerma in air (up to 10 cGy). Change in film reflectance was determined with an in-house written code using images produced by a flatbed document scanner. Calibration curves for each beam quality were created, and film responses for same air-kerma values were compared.Sets of film strips were placed into holes of a CTDI phantom and irradiated for several clinical scanning protocols on CT-simulators and CBCT systems. Film reflectance change was converted into dose to water and used to calculate CTDIvol values. Measured CTDIvol values were compared to tabulated CTDIvol values. Results: Average variations of ±5.2% in the mean film reflectance change were observed in the energy range of 80 to 140 keV, and 11.1% between 50 and 140 keV. The averaged measured CTDI values presented a mean variation for the same machine and protocol of 2.6%. However, measured CTDI values were in average 10% lower than tabulated CTDI values for CT-simulators, and 44% higher for CBCT systems. Conclusion: We found that in relatively broad range of beam qualities used in diagnostic radiology variation of film response is within ±5% resulting in ±15% systematic error in dose estimates if a single calibration curve is used. Relatively large discrepancy between measured and tabulated CTDI values for different protocols and imaging systems used within radiotherapy department strongly support the trend towards replacing CTDI value with equilibrium dose measurement in the center of cylindrical phantom as suggested by TG-111. This work was supported by the Natural Sciences and Engineering Research Council of Canada, Contract No. 386009; Partial support by CREATE, Medical Physics Research Training Network grant of the Natural Science and Engineering Research Council, Contract No. 432290.

07 ISOTOPE AND RADIATION SOURCES↗