Search NASA⌕ Search

SEARCH · Search NASA

Results for “UO2 Fuel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Integral Experiment Request 523 CED-2 Report

This report documents the final design phase of the Critical Experiment Design (CED-2) conducted as part of integral experiment request (IER) 523. The purpose of IER 523 is to determine critical configurations of 35 weight percent (wt%) enriched uranium dioxide beryllium oxide (UO 2 -BeO) material driven by an annular ring of Seven Percent Critical Experiment (7uPCX) fuel rods at Sandia National Laboratories (Sandia). The experiments will provide benchmark data on water moderated, intermediately enriched UO2 systems as well as Be nuclear data. The experiment will also provide partial validation for the beryllium oxide (BeO) thermal neutron scattering law (TSL) in the thermal energy range. Experiment design concepts, neutronic analysis results, and proposed paths for continuing the CED process are presented. This report builds on the feasibility and justification of experimental need report (CED-0) and preliminary experiment design report (CED-1) completed in December 2021 and September 2023, respectively [1, 2].

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

MECHANISTIC MULTIPHYSICS MODELING OF CLADDING RUPTURE IN NUCLEAR FUEL RODS DURING LOSS-OF-COOLANT ACCIDENT CONDITIONS

The Loss of Coolant Accident (LOCA) is a design basis accident that is included as part of the safety analysis of nuclear power plants. As the nuclear industry desires to increase the cycle length and discharge burnup of existing nuclear power plants they must demonstrate safe operation during a LOCA on high burnup fuel. During a LOCA transient on high burnup fuel rods, the rods may undergo a process known as fuel fragmentation, relocation, and dispersal (FFRD). To permit dispersal, the cladding encapsulating the fuel must rupture with an opening size large enough to allow the fragmented fuel particles to release. Current licensing tools used by industry and the United States Nuclear Regulatory Commission are limited in geometric fidelity and materials that can be analyzed. These simulation tools generally employ a quasi-two-dimensional (1.5D or Layered1D) or 2D-RZ axisymmetric geometric representations exclusively. While a valid approach under some instances, there are times when important physics have an asymmetric behavior in the fuel rod. Examples include fuel fragmentation, thermal-hydraulic boundary conditions, and cladding rupture, all of which are important for LOCA analysis. As industry pursues burnup extensions it must be demonstrated that fuel dispersal can be mitigated or eliminated. To do this, an understanding of the rupture opening after cladding failure is required. This work presents the development of a model for predicting the size and location of the rupture opening in failed fuel rods during LOCA conditions using advanced modeling and simulation tools. In order to supply the rupture model with appropriate boundary conditions, improvements to fuel fragmentation, axial relocation and oxidation modeling were required. First, the eXtended Finite Element Method (XFEM) is used to mechanistically predict the number of fuel fragments that form due to material strength randomization, criteria for strength randomization, mesh density, power ramping rates and irradiation effects. These predictions with associated uncertainty were compared to empirical correlations developed for UO2 verifying that they can be used with increased confidence in subsequent axial relocation analyses. Secondly, a new first-of-its-kind Layered2D computational framework was developed that provides the ability to apply azimuthally varying boundary conditions while providing discrete layers to track fuel movement during the LOCA. An existing fuel axial relocation model developed for Layered1D was extended to work within the Layered2D framework. A large sensitivity study was performed on the initial version of the model to identify modeling parameters of particular importance, with the emissivity used for radiation after blowdown being the primary source of uncertainty. Then, a simplistic approach to incorporate mechanical degradation of the cladding due to oxidation was also developed to investigate the impact of reduced cladding thickness on predictions of the time to failure of cladding tubes. It was found that the cladding will typically rupture prior to a reduction in thickness that is sufficient to impact the rupture behavior. A model was then developed for predicting cladding rupture that transfers the cladding surface temperatures, rod internal and external pressures, fast neutron fluence, and fast neutron flux from a more detailed Layered1D, Layered2D, or 2D-RZ analysis to a 3D cladding only analysis. Comparisons of the rupture model to a few experiments indicate reasonable predictions. The rupture model was then applied to two accident tolerant fuel concepts (FeCrAl and Cr-coated Zircaloy) where it predicted that both ATF concepts would have smaller rupture openings and delayed rupture times than the standard Zircaloy-4 cladding material under identical loading conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Characterization of high thermal conductivity fuel surrogates before and after ion irradiation

High thermal conductivity nuclear fuels offer important potential advantages over traditional oxide-based fuels such as higher burnup, reduction in fission gas release, and better overall safety of the system. One proposed approach to high thermal conductivity fuels utilizes high thermal conductivity nonfissile additives with UO 2 fuel to lower the fuel operating temperature and thereby take advantage of the highly favorable radiation resistance of UO 2 at lower operating temperatures. However, differential swelling in the matrix and high conductivity additive phases during high dose irradiation could lead to internal cracking and poor performance. In the current study, ceria (CeO 2 ) and zirconia (ZrO 2 ) surrogate matrices were used to model UO2 behavior. Additives of 10 vol. % Al 2 O 3 or SiC in the form of short fibers or platelets were used for the high conductivity second phase. The nuclear fuel surrogates were sintered to achieve densities greater than 93% of the ideal values. Scanning electron microscopy (SEM) imaging and X-ray diffraction confirmed the uniform distribution of the second phase and that no intermetallic second phase was formed during sintering. The thermal conductivity of the sintered samples was measured from 50 °C to 900 °C and confirmed the desirable increase compared to pure CeO 2 /ZrO 2 pellets. Samples were irradiated with 20 MeV Ni 6+ ions at midrange doses ranging from 1 to 15 displacements per atom (dpa) and temperatures from 300 °C to 700 °C. Post irradiation characterization revealed a good stability of the samples at low to medium doses with matrix lattice parameter swelling of < 0.14 % but showed a significant microstructural deterioration and decrease of the mechanical properties at 15 dpa.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Modeling of fission gas diffusion and release for Gd 2 O 3 doped UO 2

Uranium dioxide (UO 2 ) is the primary nuclear fuel in light water reactors, and its excess neutronic reactivity can be controlled by adding burnable absorbers, such as Gd 2 O 3 . This burnable absorber has a large neutron absorption cross-section, lowering the high reactivity of the reactor's initial fuel load. However, there needs to be more understanding of how added Gd 2 O 3 influences the properties of UO 2 under irradiation. To understand the behavior of defects and fission gas in the UO 2 /Gd 2 O 3 system under irradiation, we use cluster dynamics modeling supported by density functional theory calculations. First, we calculate the formation energies of Gd point and cluster defects, and evaluate the temperature-dependent defect concentrations using the defect formation energies and entropies. We show that Gd is soluble in UO 2 , introducing a negative charge in the system. Using this information, we adapted the cluster dynamics code Centipede to model the influence of Gd on U self-diffusion and Xe diffusion in UO 2 with 10 wt% Gd 2 O 3 . Also, we analyzed the Xe diffusion as a function of Gd 2 O 3 concentration, showing that the Xe diffusivity is decreased, which means that the athermal diffusivity due to electronic stopping persists at higher temperatures. In conclusion, the decrease in Xe diffusion means that more Xe stays in the matrix, decreasing the Xe release, and lowering its influence of fission gas release on the thermomechanical properties of UO 2 .

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Cluster Dynamics Simulations of Intra-Granular Fission Gas Bubble Size and Pressure Evolution in UO 2

Fission gases such as xenon (Xe) play a critical role in determining the behavior and response of nuclear fuel. Given that Xe has little solubility in UO 2 , it accumulates and forms bubbles, which significantly impact fuel performance. Intra- and inter-granular bubble nucleation and growth can lead to fuel swelling, and once bubbles interconnect at grain boundaries, fission gas can be released into the plenum. At low temperatures, limited uranium vacancy mobility can restrict swelling, therefore causing the bubbles to become highly pressurized. Consequently, this can induce micro-cracking, promote fission gas release (increasing the likelihood of cladding failure), and even lead to fuel pulverization under accident conditions such as a loss of coolant accident. As bubble evolution is strongly influenced by local temperature and fission rate, markedly different behavior occurs across the radial profile of the fuel pellet. Capturing the mechanisms that underpin bubble evolution is therefore important to predict these behaviors in the fuel. Previous models describing important mechanisms informed by lower length scale simulations have been developed under the NEAMS program. These can describe the evolution of a single bubble type (i.e., single value for radius and pressure) at each position in the pellet, for instance using the Centipede cluster dynamic code. However, in reality, a full distribution in bubble sizes and pressures exists within the microstructure at a given position in the pellet. To address this the cluster dynamics code Xolotl, which can predict Xe and vacancy phase space (i.e., bubble distributions) for intra-granular bubbles, has been used before. Prior work benchmarked the Xolotl code against the Centipede cluster dynamics code to ensure compatibility and to verify that mobile defect properties are adequately transferred between the two codes, along with some physics improvements. In this work, we go further by introducing a physics-based set of improvements that will allow us to accurately predict bubble size distributions and internal bubble pressures under representative UO 2 irradiation conditions. The improvements include (i) coupling bubble-defect reaction energies to a virial equation of state (EOS), (ii) including a bubble surface tension contribution, (iii) incorporating radiation-induced re-solution of Xe and vacancies, (iv) enabling pressure-driven dislocation loop punching through an effective emission of interstitial clusters informed by interstitial loop energetics, (v) accounting for radiation induced athermal diffusion of Xe, and (vi) implementing a Booth-type grain boundary sink representation for all mobile defects and defect clusters. After these modifications, we observe good agreement of Xolotl fission gas bubble size and concentration predictions with legacy experimental measurements. Additionally, it allows the distribution of Xe bubble pressures and radius to also be predicted and compared to data produced through the Advanced Fuels Campaign (AFC) program. Here, we have done this by running simulations under conditions similar to the AFC post-irradiation examination (PIE) samples irradiated at North Anna 2 light water reactor (LWR). Our results shows excellent agreement with these experimental measurements.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Microstructural and Oxidation Effects of Nb Additions to U3Si2

U3Si2 is a long term, accident-tolerant nuclear fuel candidate for light-water reactors because of its superior thermal conductivity and increased uranium density when compared to traditional uranium dioxide (UO2). While reducing internal thermal stresses and increasing efficiency, U3Si2 exhibits energetic oxidation during certain off-normal and accident scenarios, which include coolant or steam exposure. To mitigate this, Nb is investigated as an alloy constituent to enhance corrosion resistance and increase mechanical strength. The work presented investigates the response of Nb-alloyed U3Si2 to steam atmospheres. A thermogravimetric analysis is conducted in flowing steam to T > 1000 °C to assess oxidation resistance. The phase characterization of as-melted, thermally annealed and post-oxidation compositions with up to 12 vol% Nb by powder X-ray diffraction, scanning electron microscopy, and energy dispersive spectroscopy is reported.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2019

Postirradiation Examination of the ATF-1 Experiments - 2019 Status

A collaborative effort of the Advanced Fuels Campaign together with industry consortia is focused on the development of enhanced accident tolerant fuels for Light Water Reactors (LWRs). The scoping studies, referred to as ATF-1 irradiations, are being performed in the Advanced Test Reactor of Idaho National Laboratory using drop-in style irradiations. The Post-Irradiation Examinations (PIEs) of ATF-1 began in 2017 and continued in 2019. This report describes the results of examinations on ATF-1 irradiations designed to test the performance of advanced iron-based cladding, including compatibility of FeCrAl with UO2, and ATF-1 irradiation of U3Si5. Two rodlets with commercial iron-based cladding and UO2 pellets have been irradiated to low burnup (i.e., < 20 GWd/tHM). The first rodlet had an Alloy33 cladding, while the other had a Kanthal APMT® cladding. The performed PIEs were focused on the determination of fuel microstructure, evaluation of fuel-cladding interaction and irradiation-induced variations of cladding mechanical properties. For both rodlets, no significant changes in the cladding hardness were measured, and the cladding hoop strain remained limited. Gamma tomography revealed no Cs axial migration as expected for LWR fuel, but significant cesium radial migration, which was induced by thermal migration consequent to high irradiation temperatures. Microstructure analyses revealed formation of secondary phases along the pellet rim of samples from both rodlets. No wastage or extensive chemical interaction between the fuel and the internal wall of the cladding was observed, suggesting that the secondary phases accumulated at the pellet rim might be due to formation of Cs-U-O compounds. However, further advanced PIEs are necessary to finally confirm this hypothesis. Optical microscopy analysis of the rodlet designed by Oak Ridge National Laboratory to evaluate the interaction between UO2 and various FeCrAl alloys revealed no extensive interaction in all the samples irradiated in the rodlet. Localized defects, namely circular pitting and cracks of a few tents of microns, were observed on the FeCrAl disc surfaces in some of the diffusion couples. These defects might be surface fabrication defects rather than irradiation-induced localized corrosion, but chemical analyses are needed to determine whether accumulation of corrosive fission products are causing enhanced interaction. Both non-destructive and destructive PIEs were collected on a rodlet containing U3Si5 fuel. The rodlet had extremely low fission gas release, similar to previously analyzed U3Si2 rodlets. Gamma tomography revealed thermo-migration of fission product ruthenium toward the center of the fuel pellet. The fuel microstructure resembles the as-fabricated microstructure, showing extensive microcracking related to the phase transition at 450°C. Two types of secondary phases were observed, which could either be due to segregation and precipitation of fission products or to UN impurities from fabrication. Finally, the current status of PIE on other ATF-1 irradiations will be discussed. These irradiations include UN-U3Si5 rodlets, UN-U3Si2 rodlets and an additional test with U3Si2 fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Grain subdivision and structural modifications by high-energy heavy ions in UO 2 with different initial grain size

Irradiation with 84 MeV Xe ions at peak fluence above 7 × 10 17 ions/cm 2 has been carried out on two UO 2 samples with different initial grain sizes at 300 °C and 500 °C. Characterization of both grain structure and bubble morphology has been performed using transmission electron microscopy, image analysis and precession electron diffraction. The bubble size in the large-grained sample was smaller than that in the standard-grain sample, confirming fission gas precipitation resistance in the former. The ion irradiation in the high electronic energy deposition range has caused formation of a large density of dislocations which resulted in grain polygonization for the sample with standard grain size, which was observed in multiple lamellas extracted next to each other at peak dose. The sample with large grains showed inconsistent behavior. In one case, dislocation pile-up occurred, but no sub-grain formation was observed. An adjacent location showed sub-grain formation, even if to less extent compared to the standard grain-size sample. Furthermore, these findings suggest a limited polygonization resistance in large-grained UO 2 compared to standard-grain UO 2 . Recrystallization of both sample surfaces was present, leaving unclear if this is a surface effect or a consequence of the highest energy deposition rate in this area.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2018

Summary Technical Report for Conceptual Design of MARCH-SERTTA

The Transient Reactor Test facility (TREAT) was constructed in the late 1950’s, provided thousands of transient irradiations before being placed in standby in 1994, and resumed reactor operations in 2017 in order to reclaim its crucial role in nuclear-heated safety research [1]. Starting in September of 2018, TREAT performed its first series of new fueled transient experiments using a novel modular irradiation vehicle, termed the Minimal Activation Retrievable Capsule Holder (MARCH) system. The MARCH system was developed to support high throughput testing and post transient examination by using fresh fuel samples arranged in low-activation hardware materials. Deployment of this irradiation vehicle system was supported by the Accident Tolerant Fuels (ATF) program. These initial experiments used inert gas atmosphere capsules (referred to as the Separate Effects Test Holder, SETH) containing small rodlets composed of UO2 pellets in zirconium alloy cladding with temperature measurement instruments. The initial SETH campaign was conducted in order to commission irradiation capabilities and deepen the understanding of specimen to core energy coupling. Building upon the successes of the initial SETH campaign, an evolution of the capsule design has been conceptualized in order to support the same kind of high throughput, cost effective, rodlet scale testing, but with the notable improvement of being able to immerse specimens in liquid water for testing conditions better representing Light Water Reactors (LWR). This capsule is referred to as the MARCH system Static Environment Rodlet Transient Test Apparatus (MARCH-SERTTA).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2019

TREAT Fuel Motion Summary Report. SETH A-E Experiments

In support of the Accident Tolerant Fuels program, experiment devices are being developed to enable transient testing of pressurized water reactor (PWR) type fuel specimens. In fiscal year 2019 several fueled tests were conducted in the Transient Reactor Test Facility (TREAT) using the Separate Effects Test Holder (SETH). Five different SETH capsules (SETH A-E) were assembled, each holding a 10-pellet rodlet with 4.9% enriched, commercially-produced fresh UO2 pellets in zirconium alloy cladding with pellet dimensions having typical PWR radial dimensions and a total pellet stack length measuring 10.16 cm. The rodlet’s length allows the specimen to be axially positioned in the center of the core with minimal flux variation over the height of the rodlet. The fuel motion monitoring system (FMMS) is located on the north side of the TREAT reactor. Having direct line-of-sight of the core enables the FMMS to collect spatially-resolved data for fast neutrons generated due to fission occurring in experiment specimens. The FMMS contains 360 channels that make up a 10 (horizontal) by 36 (vertical) array of viewing slots; for the SETH A-E test series 96 proton-recoil scintillator (PRS) detectors were installed in the system. The fast neutrons are detected in the PRS detectors from light produced by the recoil of protons interacting with ZnS(Ag) grains in each detector's scintillator button. This report focuses on the FMMS data captured in the SETH A-E experiments, with multiple transients varying in reactivity addition and length. The first three experiments had a total reactor energy of 101 MJ each and were critical in understanding the FMMS field of view, lead shielding, and other TREAT data acquisition systems. SETH-B2 and C had a reactivity addition of almost double the previous transients and served as a demonstration of the detector array behavior under increased reactor energy. The final two SETH experiments (D and E) were aimed at reaching cladding melting temperatures with a reactor energy over 500 MJ for each test. In preparation for the higher energy transients, the FMMS lead shielding was reduced to 0.5 inches from the 6 inches used in SETH A-C. This was expected to saturate the detectors at the peak of the transient in exchange for higher sensitivity at lower energies after the peak, when the motion was expected. SETH-D was clipped at approximately 3 seconds, which was too early for the FMMS to capture any rodlet motion. SETH-E had the same reactivity addition as SETH-D but the transient time was extended to 18 seconds. The FMMS captured the downward motion of the rodlet in SETH-E as the count rate significantly changed for the detectors viewing the specimen. Snapshots taken throughout the transient helped identify the approximate time at which the motion initiated. Further analysis of the individual detector data captured on a per-millisecond time basis resulted in a determination that the approximate time for the onset of the downward motion was 2.84 ± 0.02 seconds. Neutron radiographs confirmed that downward motion occurred for SETH-D and SETH-E. Motion in SETH-D could also have been captured by the FMMS if the transient time had been longer for SETH-D. Ultimately, these final two tests served to demonstrate the FMMS's ability to track fuel motion during transient experiments at TREAT.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Destructive Examination of a FeCrAl-UO 2 Irradiation Test

Several destructive postirradiation examinations were performed on an irradiation specimen that coupled an early iron-chromium-aluminum (FeCrAl) candidate alloy cladding with UO2 pellets. This irradiation test was designed to investigate the early life performance and compatibility of the FeCrAl-UO 2 cladding-fuel system under prototypic light water reactor neutronic conditions. Additionally, these tests were expected to provide neutron irradiated samples for severe accident testing of this fuel system. The irradiation studied in this work was part of the ATF-1 series of drop-in style irradiations performed in the Idaho National Laboratory Advanced Test Reactor. The rodlet studied in this work is one of three similar rodlets irradiated in ATF-1 that had approximately 7.6 cm of cladding machined from a wrought FeCrAl alloy and fueled with a 6.1 cm stack of UO 2 pellets. The outer diameter of the cladding was ~0.94 cm and the inner diameter was ~0.83 cm. After irradiation and non-destructive examination in Idaho this rodlet was shipped to the Oak Ridge National Laboratory hot-cells for further examination. The irradiated rodlet was sectioned into several samples for microstructural, micromechanical, and severe accident testing. During sectioning, it was noted that the fuel was not firmly bonded to the cladding and could be readily removed from small cladding slices. Microstructural characterization of fuel cross sections also revealed no significant interaction between the fuel and the cladding. Samples were also prepared for microhardness testing. To prepare for high temperature oxidation testing, the fuel was dissolved from segments of the cladding. High temperature oxidation testing of cladding segments was performed at 1200°C and 1300°C in a steam environment. Comparisons between the oxidation of this FeCrAl alloy in its neutron irradiated state, as-fabricated state, and the oxidation of Zircaloy-2 are made. The oxidation testing will be followed by ring compression testing to evaluate ductility. The microstructure of the samples after oxidation and ring compression testing will also be analyzed.

Harp, Jason↗
DOE OSTI2022

Measuring the Electrochemical Corrosion of 233U-doped UO2 in a Microfluidic Device

We have developed a microfluidic, ‘particle-attached microfluidic electrochemical’ device, or PAMEC, that uses microgram quantities of radioactive materials, such as uranium dioxide (UO2), rather than bulk specimens to both observe electrochemical changes and measure spectroscopic properties. The PAMEC device reduces the need for running experiments in a shielded facility and allows for in-operando, real-time investigations of electrochemical properties and morphological changes of micrograms of particles. This novel design offers a promising platform to investigate spent nuclear fuel (SNF) and other nuclear materials under various controlled condition, and to provide insights to nuclear waste management, and fuel performance

Electrochemistry↗
DOE OSTI2021

BISON microstructure-based pulverization criterion in high burnup structure

To improve the economics of commercial nuclear power production, utilities are seeking to increase the allowable burnup limit of UO$_2$ fuel. One of the main factors that contributes to the current burnup limit of 62 GWd/MTU in commercial light water reactors (LWRs) is the risk of fine fragmentation or pulverization during a loss of coolant accident (LOCA). Pulverization primarily occurs at high burnups, especially when the high burnup structure (HBS) has formed. To allow the industry to pursue increased burnup and develop mitigation strategies, it is essential to have improved capability to predict the onset of pulverization. However, the mechanism of pulverization is not well understood, and the existing predictive capabilities implemented in the BISON fuel performance code are empirical in nature. In this report, mesoscale simulations are used to improve understanding of the formation mechanism of the HBS and how it responds during a LOCA transient, and inform development of a BISON pulverization criterion. A phase-field model was used to simulate the evolution of bubble pressure as a result of HBS formation. The simulations showed that gas atoms diffuse from grain interiors to the new grain boundaries created during HBS formation, and diffuse rapidly along these grain boundaries to reach existing bubbles. This causes an increase in bubble pressure in existing bubbles, leading to bubble growth during steady-state operation. To simulate the response of HBS bubbles to a LOCA transient, a newly developed phase-field model was used; in agreement with preliminary results from FY20, bubble size did not change significantly during the duration of the transient. A phase-field fracture model was used to study fragmentation patterns in the HBS, including using input from the phase-field model as initial conditions. Phase-field fracture simulations were used to determine a pulverization criterion for BISON. A function for the critical pressure for pulverization to occur was fit to data from the phase-field fracture simulations, and this function was implemented as a material property in BISON. For comparison, an analytical criterion for pulverization was developed and implemented within the same material property.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2019

In Situ Electrochemical Testing of Uranium Dioxide under Anoxic Conditions (FY19 Report)

Prediction of the corrosion behavior of spent uranium oxide (UO 2 ) fuel is needed for developing predictive performance assessment models for a geologic repository. Currently, the Fuel Matrix Dissolution Model (FMDM) is being used for modeling UO 2 chemistry in the Engineered Barrier System (EBS) and includes the effects of oxidants, oxygen and hydrogen peroxide generated from radiolysis of the fuel in contact with water as well as the role of hydrogen on limiting corrosion. The aim of this work is to investigate the corrosion of UO 2 in-situ in the Scanning Electron Microscope (SEM). The corrosion potential (E corr ) is measured using an electrochemical workstation and a unique microfluidic reactor containing three-electrodes and compatible for multiple analytical platforms, termed System for Analysis at the Vacuum Liquid Interface (SALVI) electrochemical cell (E-cell) which has been developed at PNNL. This approach aims to provide real-time and in operando monitoring of UO 2 electrode stability and morphological change and to study the UO 2 corrosion process at the microscale. The results will be utilized to support the Mixed Potential Model (MPM) that has been developed for the repository program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2018

Alternative Crucible Materials

This is a presentation for the JFCS joint ERWG/SSWG meeting to be held next week (May 15-17). It is a presentation on alternative materials for crucibles including BeO, HfN coated Nb, and UO2. It will be presented at the INL with South Korean foreign nationals present.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2019

Post-irradiation Examinations of Accident Tolerant Fuel Candidates with Iron-alloy Cladding

A collaborative effort of the Advanced Fuels Campaign together with industry consortia is focused on the development of enhanced Accident Tolerant Fuels (ATF) for Light Water Reactors (LWRs). The scoping studies, referred to as ATF 1 irradiations, are being performed in the Advanced Test Reactor of Idaho National Laboratory using drop-in style irradiations. The Post Irradiation Examinations (PIEs) of ATF-1 began in 2017 and continued in 2019. This report describes the results of examinations on ATF-1 irradiations designed to test the performance of iron-based cladding. Two rodlets with commercial iron-based cladding and UO2 pellets have been irradiated to low burnup (i.e., < 20 GWd/tHM). The first rodlet had an Alloy33® cladding, while the other had a Kanthal APMT® cladding. The performed PIEs were focused on the determination of fuel microstructure, evaluation of fuel cladding interaction and irradiation-induced variations of cladding mechanical properties. For both rodlets, no significant changes in the cladding hardness were measured, and the cladding hoop strain remained limited. Gamma tomography revealed no Cs axial migration as expected for LWR fuel, but significant cesium radial migration, which was induced by thermal migration consequent to high irradiation temperatures compared to standard LWR irradiation temperatures. Microstructure analyses revealed formation of secondary phases along the pellet rim of samples from both rodlets. No wastage or extensive chemical interaction between the fuel and the internal wall of the cladding was observed, suggesting that the secondary phases accumulated at the pellet rim might be due to formation of Cs-U-O compounds. However, further advanced PIEs are necessary to confirm this hypothesis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Structure and Process of Managing the UO2 Dry In-Pile Fracture Test Irradiation Experiment

The management and structure of a novel research and development (R&D) project can be hard to navigate. This is especially true when it involves nuclear fuel. Familiarity with institutional safety and procedural requirements, a well defined scope, and accurate cost estimates can all help ensure successful project management from start to finish. The Dry In-Pile Fracture Test (DRIFT) experiments performed at the Transient Test Reactor Facility are an excellent example of managing an R&D project within its scope and budget constraints. The objective of the DRIFT test was to develop fracture propagation data in a manner consistent with light-water reactors to validate and improve the fracture propagation models of uranium oxide fuels in the MOOSE (Multiphysics Object-Oriented Simulation Environment)-BISON-Marmot code framework [1].

99 GENERAL AND MISCELLANEOUS↗