SEARCH · Search NASA

Results for “Unsteady flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

NASA NTRS2004

Measurements With a Split-Fiber Probe in Complex Unsteady Flows

A split-fiber probe was used to acquire unsteady data in a research compressor. A calibration method was devised for a split-fiber probe, and a new algorithm was developed to decompose split-fiber probe signals into velocity magnitude and direction. The algorithm is based on the minimum value of a merit function that is built over the entire range of flow velocities for which the probe was calibrated. The split-fiber probe performance and signal decomposition was first verified in a free-jet facility by comparing the data from three thermo-anemometric probes, namely a single-wire, a single-fiber, and the split-fiber probe. All three probes performed extremely well as far as the velocity magnitude was concerned. However, there are differences in the peak values of measured velocity unsteadiness in the jet shear layer. The single-wire probe indicates the highest unsteadiness level, followed closely by the split-fiber probe. The single-fiber probe indicates a noticeably lower level of velocity unsteadiness. Experiments in the NASA Low Speed Axial Compressor facility revealed similar results. The mean velocities agreed well, and differences in the velocity unsteadiness are similar to the case of a free jet. A reason for these discrepancies is in the different frequency response characteristics of probes used. It follows that the single-fiber probe has the slowest frequency response. In summary, the split-fiber probe worked reliably during the entire program. The acquired data averaged in time followed closely data acquired by conventional pneumatic probes.

Lepicovsky, Jan↗

NASA NTRS1997

Unsteady Flow Field in a Multistage Axial Flow Compressor

The flow field in a multistage compressor is three-dimensional, unsteady, and turbulent with substantial viscous effects. Some of the specific phenomena that has eluded designers include the effects of rotor-stator and rotor-rotor interactions and the physics of mixing of velocity, pressure, temperature and velocity fields. An attempt was made, to resolve experimentally, the unsteady pressure and temperature fields downstream of the second stator of a multistage axial flow compressor which will provide information on rotor-stator interaction effects and the nature of the unsteadiness in an embedded stator of a three stage axial flow compressor. Detailed area traverse measurements using pneumatic five hole probe, thermocouple probe, semi-conductor total pressure probe (Kulite) and an aspirating probe downstream of the second stator were conducted at the peak efficiency operating condition. The unsteady data was then reduced through an ensemble averaging technique which splits the signal into deterministic and unresolved components. Auto and cross correlation techniques were used to correlate the deterministic total temperature and velocity components (acquired using a slanted hot-film probe at the same measurement locations) and the gradients, distributions and relative weights of each of the terms of the average passage equation were then determined. Based on these measurements it was observed that the stator wakes, hub leakage flow region, casing endwall suction surface corner region, and the casing endwall region away from the blade surfaces were the regions of highest losses in total pressure, lowest efficiency and highest levels of unresolved unsteadiness. The deterministic unsteadiness was found to be high in the hub and casing endwall regions as well as on the pressure side of the stator wake. The spectral distribution of hot-wire and kulite voltages shows that at least eight harmonics of all three rotor blade passing frequencies are present at this measurement location. In addition to the basic three rotor blade passing frequencies (R1, R2 and R3) and their harmonics, various difference frequencies such as (2R1 -R2) and (2R3-R2) and their harmonics are also observed. These difference frequencies are due to viscous and potential interactions between rotors 1, 2 and 3 which are sensed by both the total pressure and aspirating probes at this location. Significant changes occur to the stator exit flow features with passage of the rotor upstream of the stator. Because of higher convection speeds of the rotor wake on the suction surface of the downstream stator than on the pressure side, the chopped rotor wake was found to be arriving at different times on either side of the stator wake. As the rotor passes across the stator.

Suryavamshi, N.↗

NASA NTRS1979

Unsteady flow and dynamic response analyses for helicopter rotor blades

Research is presented on helicopter rotor blade vibration and on two and three dimensional analyses of unsteady incompressible viscous flow past oscillating helicopter rotor blades. A summary is presented of the two international research collaborations which resulted from the NASA project: the collaboration under the auspices of NATO between the University of Wisconsin-Milwaukee, University of Brussels, Belgium and the Aerodynamics Research Establishment in Goettingen, West Germany, and the collaboration under the auspices of the National Science Foundation between UWM and the University of Hamburg and the Ship Research Establishment in Hamburg, West Germany. A summary is given of the benefits from the NASA project to UWM, the College of Engineering and Applied Science, and the participants on the project.

Bratanow, T.↗

NASA NTRS1979

Unsteady flow model for circulation-control airfoils

An analysis and a numerical lifting surface method are developed for predicting the unsteady airloads on two-dimensional circulation control airfoils in incompressible flow. The analysis and the computer program are validated by correlating the computed unsteady airloads with test data and also with other theoretical solutions. Additionally, a mathematical model for predicting the bending-torsion flutter of a two-dimensional airfoil (a reference section of a wing or rotor blade) and a computer program using an iterative scheme are developed. The flutter program has a provision for using the CC airfoil airloads program or the Theodorsen hard flap solution to compute the unsteady lift and moment used in the flutter equations. The adopted mathematical model and the iterative scheme are used to perform a flutter analysis of a typical CC rotor blade reference section. The program seems to work well within the basic assumption of the incompressible flow.

Rao, B. M.↗

NASA NTRS1997

Computational Aeroservoelastic Analysis with an Euler-Based Unsteady Flow Solver

The effectiveness of transpiration for simulation of structural deformations in steady and unsteady aeroelastic applications is examined. The majority of the investigations were performed using a highly integrated, finite-element code for the multidisciplinary analysis of flight vehicles. A supplement to this code, which allows for the generation of deflected meshes using modal superposition, was developed in this study. This research demonstrated that the transpiration boundary condition has strong potential for applications in unsteady aeroelastic analysis, such as in the prediction of flutter boundaries.

Arena, Andrew S., Jr.↗

NASA NTRS1996

Experimental investigation of unsteady flows at large incidence angles in a linear oscillating cascade

The aerodynamics of a cascade of airfoils oscillating in torsion about the midchord is investigated experimentally at a large mean incidence angle and, for reference, at a low mean incidence angle. The airfoil section is representative of a modern, low aspect ratio, fan blade tip section. Time-dependent airfoil surface pressure measurements were made for reduced frequencies up to 0.8 for out-of-phase oscillations at Mach numbers up to 0.8 and chordal incidence angles of 0 deg and 10 deg. For the 10 deg chordal incidence angle, a separation bubble formed at the leading edge of the suction surface. The separated flow field was found to have a dramatic effect on the chordwise distribution of the unsteady pressure. In this region, substantial deviations from the attached flow data were found with the deviations becoming less apparent in the aft region of the airfoil for all reduced frequencies. In particular, near the leading edge the separated flow had a strong destabilizing influence while the attached flow had a strong stabilizing influence.

Buffum, Daniel H.↗

NASA NTRS1997

An Experimental Investigation of Steady and Unsteady Flow Field in an Axial Flow Turbine

Measurements were made in a large scale single stage turbine facility. Within the nozzle passage measurements were made using a five hole probe, a two-component Laser Doppler Velocimeter (LDV), and a single sensor hot wire probe. These measurements showed weak secondary flows at midchord, and two secondary flow loss cores at the nozzle exit. The casing vortex loss core was the larger of the two. At the exit radial inward flow was found over the entire passage, and was more pronounced in the wake. Nozzle wake decay was found to be more rapid than for an isolated vane row due to the rotor's presence. The midspan rotor flow field was measured using a two-component LDV. Measurements were made from upstream of the rotor to a chord behind the rotor. The distortion of the nozzle wake as it passed through the rotor blade row was determined. The unsteadiness in the rotor flow field was determined. The decay of the rotor wake was also characterized.

Zaccaria, M.↗

NASA NTRS1984

Mass transfer from a circular cylinder: Effects of flow unsteadiness and slight nonuniformities

Experiments were performed to determine the effect of periodic variations in the angle of the flow incident to a turbine blade on its leading edge heat load. To model this situation, measurements were made on a circular cylinder oscillating rotationally in a uniform steady flow. A naphthalene mass transfer technique was developed and used in the experiments and heat transfer rates are inferred from the results. The investigation consisted of two parts. In the first, a stationary cylinder was used and the transfer rate was measured for Re = 75,000 to 110,000 and turbulence levels from .34 percent to 4.9 percent. Comparisons with both theory and the results of others demonstrate that the accuracy and repeatability of the developed mass transfer technique is about + or - 2 percent, a large improvement over similar methods. In the second part identical flow conditions were used but the cylinder was oscillated. A Strouhal number range from .0071 to .1406 was covered. Comparisons of the unsteady and steady results indicate that the magnitude of the effect of oscillation is small and dependent on the incident turbulence conditions.

Marziale, M. L.↗

NASA NTRS2004

Characterization of Unsteady Flow Structures Near Landing-Edge Slat: 2D Computations - Part 2

In our previous computational studies of a generic high-lift configuration, quasi-laminar (as opposed to fully turbulent) treatment of the slat cove region proved to be an effective approach for capturing the unsteady dynamics of the cove flow field. Combined with acoustic propagation via Ffowes Williams and Hawkings formulation, the quasi-laminar simulations captured some important features of the slat cove noise measured with microphone array techniques. However. a direct assessment of the computed cove flow field was not feasible due to the unavailability of off-surface flow measurements. To remedy this shortcoming, we have undertaken a combined experiment and computational study aimed at characterizing the flow structures and fluid mechanical processes within the slat cove region. Part I of this paper outlines the experimental aspects of this investigation focused on the 30P30N high-lift configuration; the present paper describes the accompanying computational results including a comparison between computation and experiment at various angles of attack. Even through predictions of the time-averaged flow field agree well with the measured data, the study indicates the need for further refinement of the zonal turbulence approach in order to capture the full dynamics of the cove's fluctuating flow field.

Khorrami, Mehdi↗

NASA NTRS2019

Numerical analysis of unsteady flow in a converging-diverging nozzle

This study investigates the physics of jet noise by the numerical solution of the three dimensional unsteady Navier-Stokes equations for a low-supersonic jet (Mach numbers on the order of 1.4) from a converging-diverging (C-D) nozzle and mixing with a subsonic surrounding flow. The numerical method used for the solution of these equations is the second order accurate MacCormack explicit predictor-corrector scheme. The numerical results are compared to the experimental results of Yamamoto for the same C-D nozzle geometry and similar operating conditions. The goal of the study is to use numerical simulation techniques to resolve accurately physical processes which contribute to jet noise, and to assess whether performing these simulations in a three dimensional geometry is worth the additional cost in computing resources as compared to a comparable simulation on a two dimensional planar or axisymmetric geometry. Scientific visualization is used to observe the spreading characteristics of the jet, as well as to examine the structure of the shocks within the jet core. The time average velocity and turbulence intensity level at various locations are computed and compared with experimental results. A two point space-time cross correlation is used to compute the mean convection speed through the shear layer, and these predictions are compared with results from theory.

James N Scott↗

NASA NTRS1988

Unsteady Flow In A Supersonic Cascade With Shocks

Operating range of turbomachinery for which stability calculated extended. TIPS (Two In-Passage Shocks) calculates unsteady lifts and moments on compressor blade if relative mach number supersonic and if two shock waves in blade passage. Written in FORTRAN IV and run on IBM 3033 with 370TSS operating system.

Molls, Frank B.↗

NASA NTRS1983

Application of laser velocimetry to unsteady flows in large scale, high speed tunnels

The optical, seeding, and data reduction procedures which have been used in the successful application of laser velocimetry to large-scale, unsteady, transonic wind-tunnel testing are described. Flowfield measurements obtained at several facilities are presented. These results include vortex flow measurements and ensemble-averaged data obtained under conditions of vortex-shedding, dynamic stall airfoil oscillation, oscillating trailing-edge control flaps, and helicopter rotor flow fields.

Owen, F. K.↗

NASA NTRS2009

Re-evaluation of an Optimized Second Order Backward Difference (BDF2OPT) Scheme for Unsteady Flow Applications

Recent experience in the application of an optimized, second-order, backward-difference (BDF2OPT) temporal scheme is reported. The primary focus of the work is on obtaining accurate solutions of the unsteady Reynolds-averaged Navier-Stokes equations over long periods of time for aerodynamic problems of interest. The baseline flow solver under consideration uses a particular BDF2OPT temporal scheme with a dual-time-stepping algorithm for advancing the flow solutions in time. Numerical difficulties are encountered with this scheme when the flow code is run for a large number of time steps, a behavior not seen with the standard second-order, backward-difference, temporal scheme. Based on a stability analysis, slight modifications to the BDF2OPT scheme are suggested. The performance and accuracy of this modified scheme is assessed by comparing the computational results with other numerical schemes and experimental data.

Vatsa, Veer N.↗

NASA NTRS1992

Viscous simulation method for unsteady flows past multicomponent configurations

The present algorithm for the numerical simulation of flows about complex configurations (whose multiple and nonsimilar components have arbitraty geometries) employs a hybridization of the domain decomposition techniques for grid generation as well as to reduce computer-memory requirements. A fully vectorized, finite-volume, upwind-biased, approximately factored multigrid method is used to solve 3D Reynolds-averaged unsteady and compressible Navier-Stokes equations simulating supersonic flows past an ogive-nose-cylinder near or within a cavity. The time-averaged surface pressures obtained compare favorably with the wind tunnel data.

Fouladi, Kamran↗

NASA NTRS1985

Unsteady Flow in Multistage Turbines

The development of an efficient model for the response of a multistage turbine to either a total pressure or total temperature distortion is discussed. Each turbine blade row is modeled as an actuator disk and is often used to describe the flow through turbine and compressor blade rows. The flow approaching the blade row is assumed to be subsonic and inviscid. The distortion occurs at upstream infinity and is in the form of total pressure or total temperature. A solution was found to unsteady Euler equations by using a finite volume method. With prescribed inlet and boundary conditions flow variables such as density, pressure, and velocities can be calculated at cell centers in the entire flow region. The inlet and exit of the blade row coincide with lines of constant.

Surampudi, S. P.↗

NASA NTRS1979

A note on the interaction of unsteady flow with an acoustic liner

The effects of a mean grazing flow on the energy exchanges involved in the interaction of a bias-flow acoustic liner with, respectively, incident sound and boundary layer turbulence are contrasted. The analysis of model problems which make use of a line vortex to simulate large scale, unsteady boundary layer structures indicates that, whereas acoustic waves may be effectively attenuated, dissipation caused by 'jetting' in the apertures of the liner can result in a net transfer of energy from the mean flow to the turbulence in the boundary layer.

Howe, M. S.↗

NASA NTRS1992

Computed unsteady flows of airfoils at high incidence

The flow over an airfoil at an angle of attack above the static stall angle would ordinarily be massively separated. Under dynamic conditions, the onset of stall can be delayed to an angle, depending on the type of unsteadiness, much higher than that for static stall. The stall onset mechanisms under dynamic conditions are unclear. Due to extreme difficulties involved, experimental investigations, so far, have provided insufficient information about the flow field for the identification of the onset mechanisms. A course of classical boundary layer analysis augmented with numerical experiments and measured data is chosen here instead, with the hope that the identification of onset mechanisms can be more systematic and quantitative.

Fung, K.-Y.↗

NASA NTRS1985

An implicit time-marching method for studying unsteady flow with massive separation

A fully implicit time-marching method is developed such that all spatial derivatives are approximated using central differences, but no use is made of any artificial dissipation. The numerical method solves the discretized equations using Alternating Direction Implicit-Block Gaussian Elimination technique. The method is implemented in the unsteady analysis, which solves the incompressible Navier-Stokes equations in terms of vorticity and stream function in generalized orthogonal coordinates. A clustered conformal C-grid is employed, and every effort is made to resolve the various length scales in the flow problem. The metric discontinuity at the branch-cut is treated appropriately using analytic continuation. Introduction of the BGE reordering permits implicit treatment of the branch cut in the numerical method. The vorticity singularity at the cusped trailing edge is also appropriately treated. This accurate and efficient implicit method is used to study flow at Re = 1000, past a 12-percent thick symmetric Joukowski airfoil at high angle of attack 30 and 53 deg.

Osswald, G. A.↗