Search NASA⌕ Search

SEARCH · Search NASA

Results for “VELOCITY PROBE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Plasma filaments in the scrape-off layer of Wendelstein 7-X

Plasma filaments have been observed by reciprocating electric probes in the Scrape-Off Layer (SOL) of the Wendelstein 7-X stellarator. Comparison with target probes indicates that a filament observed in the W7-X SOL extends to the sheath. Two-dimensional simulations of seeded filaments exhibit good quantitative agreement with experimental measurements in filament velocity scalings, despite an assumption of constant field line curvature. Both experiment and simulation show a slow radial propagation of filaments, indicating that filaments are essentially bound to their flux surface and do not perform ballistic radial motion. In contrast, the poloidal propagation along flux surfaces is much faster than the radial motion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Simultaneous 10 kHz three-dimensional CH 2 O and tomographic PIV measurements in a lifted partially-premixed jet flame

High-speed, three-dimensional (3D) scalar-velocity field measurements are demonstrated in a lifted partially-premixed dimethyl-ether/air jet flame using simultaneous laser-induced fluorescence (LIF) of formaldehyde (CH 2 O) and tomographic particle image velocimetry (TPIV). The 3D LIF measurements are performed by raster scanning the laser beam from a 100 kHz pulse-burst laser across the probe volume using an acousto-optic deflector. The volumetric reconstruction of the LIF signal from ten parallel planes provides quasi-instantaneous 3D LIF measurements that are synchronized with 10 kHz TPIV measurements. Here, the temporally resolved CH 2 O-LIF and velocity field data are used to analyze Lagrangian particle trajectories and displacement speeds at the base of the lifted flame. The particle trajectories reveal flow structures that are difficult to observe in an Eulerian reference frame. Positive and negative displacement speeds are observed at the CH 2 O-LIF surfaces at the inner and outer regions of the jet flame with a maximum displacement speed of approximately eight times the laminar flame speed of a stoichiometric dimethyl-ether/air mixture. The observations in present study support formation of lean premixed flames near the flame base whose role in flame stabilization should be investigated in more detail.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Development of a Comprehensive Two-Phase Flow Database for the Validation of NEK-2P

Three-dimensional (3-D) two-phase Computational Fluid Dynamics (CFD) codes are emerging as a powerful and potentially practical tool for applications in which detailed local flow information is needed. However, two-phase flow models and associated closure relations are not well established for CFD applications, which is partly due to the lack of high-quality validation data. The main objective of this work is to develop a comprehensive database of two-phase flows that can be used to validate two-phase CFD codes such as NEK-2P. In this project, four advanced local measurement systems, including Particle Image Velocimetry and Planar Laser-Induced Fluorescence (PIV-PLIF), high-speed imaging, x-ray densitometry, and multi-sensor conductivity probe are employed to measure the local two-phase flow parameters of both gas and liquid phases. By combining these techniques, the local void fraction, bubble velocity, interfacial area concentration, bubble frequency, liquid velocity, turbulence intensity, etc., in various two-phase flow regimes can be obtained. These local measurement techniques are first used in a 25.4 mm circular pipe test section. Seven air-water two-phase flow conditions spanning the bubbly, slug, churn-turbulent, and annular flow regimes are measured in this facility. The obtained database contains the radial profiles of both gas- and liquid-phase parameters at three axial locations along the test section. The second facility used in this work contains a 30 mm × 10 mm rectangular test section, in which three two-phase flow and two single-phase flow conditions are measured. Two-dimensional distributions of local two-phase flow parameters in the cross-sectional plane are measured in this facility at three axial locations as well. A facility featuring a 3×3 electrically heated rod bundle is also designed and being constructed in this project. This facility is specially designed for optical measurements and is expected to provide high-quality boiling data in the future. Preliminary analyses have been performed for the data taken in the 25.4 mm circular pipe. Both center-peaked and wall-peaked void fraction profiles have been observed in the data depending on the two-phase flow conditions and/or developing lengths. The 1-D drift-flux model was evaluated with the newly obtained datasets, in which both gas- and liquid-phases data were directly measured. The distribution parameter model has been optimized based on a new void-profile classification method proposed in this study. The optimized drift-flux model shows a significant improvement in predicting both gas velocity and void fraction. The measured liquid-phase turbulence was used to benchmark Sato’s turbulence model considering the bubble-induced shear stress for the three tested bubbly flows. The benchmark results showed good agreement between the PIV measurements and model predictions. In the bubbly flows tested that have low void fractions less than 3%, the effect of the bubble-induced turbulence was found not significant. However, the bubble-induced shear stress becomes important with the increase of the void fraction. The Conjugate Heat Transfer (CHT) model was developed and implemented in NEK-2P. This model allows the coupled simulation of the solid domain and two-phase fluid domain, allowing the specification of realistic boundary conditions. The CHT implementation was verified first with non-boiling simulations. The predicted temperatures in the fluid domain were shown to be identical in simulations with or without the CHT model. The CHT model was then validated through simulations of three Becker benchmark CHF tests performed under both Dryout (DO) and Departure from Nucleate Boiling (DNB) conditions. Reasonably good agreement was obtained between calculated wall temperatures and corresponding experimental data.

42 ENGINEERING↗
DOE OSTI2021

Bispectral analysis of broadband turbulence and geodesic acoustic modes in the T-10 tokamak

Local fluctuations of electrostatic potential, poloidal electric field, magnetic potential and electron density are simultaneously measured in the T-10 tokamak by a heavy ion beam probe (HIBP) having a five-slit energy analyser, which allows an estimate of the turbulent particle flux and $\boldsymbol {E}\times \boldsymbol {B}$ rotation velocity in the off-minor-axis gradient zone of the toroidal plasma column. The high spatial and temporal resolution of the modern multichannel HIBP makes it an effective tool to study plasma oscillations. Motivated by previous work that has documented time-resolved interactions between measured plasma parameters using correlation analysis (coherence of $E_{\textrm {pol}}$ and density $n_e$ , and cross-phase), a new result from bicorrelation analysis (bicoherence of magnetic potential $A_\zeta$ and density $n_e$ , and biphase) is reported for documenting the evidence of wave–wave coupling and energy transfer associated with the interaction between geodesic acoustic modes (GAM) and broadband, quasi-coherent modes.

Physics↗
DOE OSTI2022

The Signatures of Self-interacting Dark Matter and Subhalo Disruption on Cluster Substructure

The abundance, distribution, and inner structure of satellites of galaxy clusters can be sensitive probes of the properties of dark matter. We run 30 cosmological zoom-in simulations with self-interacting dark matter (SIDM), with a velocity-dependent cross section, to study the properties of subhalos within cluster-mass hosts. We find that the abundance of subhalos that survive in the SIDM simulations are suppressed relative to their cold dark matter (CDM) counterparts. Once the population of disrupted subhalos—which may host orphan galaxies—is taken into account, satellite galaxy populations in CDM and SIDM models can be reconciled. However, even in this case, the inner structures of subhalos are significantly different in the two dark matter models. We study the feasibility of using the weak-lensing signal from the subhalo density profiles to distinguish between the cold and self-interacting dark matter while accounting for the potential contribution of orphan galaxies. We find that the effects of self-interactions on the density profile of subhalos can appear degenerate with subhalo disruption in CDM, when orphans are accounted for. With current error bars from the Subaru Hyper Suprime-Cam Strategic Program, we find that subhalos in the outskirts of clusters (where disruption is less prevalent) can be used to constrain dark matter physics. In the future, the Vera C. Rubin Observatory Legacy Survey of Space and Time will give precise measurements of the weak-lensing profile and can be used to constrain σ $_{T}$/m at the ∼1 cm$^{2}$ g$^{−1}$ level at v ∼ 2000 km s$^{−1}$.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

Probing the nature of dark matter with accreted globular cluster streams

ABSTRACT The steepness of the central density profiles of dark matter (DM) in low-mass galaxy haloes (e.g. dwarf galaxies) is a powerful probe of the nature of DM. We propose a novel scheme to probe the inner profiles of galaxy subhaloes using stellar streams. We show that the present-day morphological and dynamical properties of accreted globular cluster (GC) streams – those produced from tidal stripping of GCs that initially evolved within satellite galaxies and later merged with the Milky Way (MW) – are sensitive to the central DM density profile and mass of their parent satellites. GCs that accrete within cuspy cold dark matter (CDM) subhaloes produce streams that are physically wider and dynamically hotter than streams that accrete inside cored subhaloes. A first comparison of MW streams ‘GD-1’ and ‘Jhelum’ (likely of accreted GC origin) with our simulations indicates a preference for cored subhaloes. If these results hold up in future data, the implication is that either the DM cusps were erased by baryonic feedback, or their subhaloes naturally possessed cored density profiles implying particle physics models beyond CDM. Moreover, accreted GC streams are highly structured and exhibit complex morphological features (e.g. parallel structures and ‘spurs’). This implies that the accretion scenario can naturally explain the recently observed peculiarities in some of the MW streams. We also propose a novel mechanism for forming ‘gaps’ in stellar streams when the remnant of the parent subhalo (which hosted the GC) later passes through the GC stream. This encounter can last a longer time (and have more of an impact) than the random encounters with DM subhaloes previously considered, because the GC stream and its parent subhalo are on similar orbits with small relative velocities. Current and future surveys of the MW halo will uncover numerous faint stellar streams and provide the data needed to substantiate our preliminary tests with this new probe of DM.

(Galaxy:) globular clusters: individual↗
DOE OSTI2021

Probing early-time longitudinal dynamics with the Λ hyperon's spin polarization in relativistic heavy-ion collisions

Here, we systematically study the hyperon global polarization's sensitivity to the collision systems' initial longitudinal flow velocity in hydrodynamic simulations. By explicitly imposing local energy-momentum conservation when mapping the initial collision geometry to macroscopic hydrodynamic fields, we study the evolution of systems' orbital angular momentum (OAM) and fluid vorticity. We find that a simultaneous description of the $\Lambda$ hyperons' global polarization and the slope of pion's directed flow can strongly constrain the size of longitudinal flow at the beginning of hydrodynamic evolution. We extract the size of the initial longitudinal flow and the fraction of orbital angular momentum in the produced QGP fluid as a function of collision energy with the STAR measurements in the RHIC Beam Energy Scan program. We find that there is about 100-200 $\hbar$ OAM that remains in the mid-rapidity fluid at the beginning of hydrodynamic evolution. We further exam the effects of different hydrodynamic gradients on the spin polarization of $\Lambda$ and $\bar{\Lambda}$. The gradients of $\mu_B/T$ can change the ordering between $\Lambda$'s and $\bar{\Lambda}$'s polarization.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Injection, confinement, and diagnosis of electrons and positrons in a permanent magnet dipole trap

Abstract Prerequisites for the goal of studying long-lived, magnetically confined, electron–positron pair plasmas in the laboratory include the injection of both species into the trap, long trapping times, and suitable diagnostic methods. Here we report recent progress on these tasks achieved in a simple dipole trap based on a supported permanent magnet. For the injection of electrons, both an $$\textbf{E}\times B$$ E × B drift technique (of a $$\sim $$ ∼ 2– $$\upmu $$ μ A, 6-eV beam) and “edge injection” (from a filament emitting a few mA and biased to some tens of volts) have been demonstrated; the former is suitable for low-density beams with smaller spatial and velocity spreads, while the latter employs fluctuations arising from collective behavior. To diagnose the edge-injected electrons, image potentials and currents induced on a wall probe, the magnet case, and wall electrodes were measured. Confinement of drift-injected positrons, measured experimentally, exhibited at least two well-separated timescales. Simulations reproduced this qualitatively, using a simple model of elastic collisions with residual background gas, and point to small adjustments for increasing trapping times. In a major upgrade to diagnostic capabilities, 25 bismuth germanate detectors, placed in three reentrant ports, are able to localize annihilation gammas, which will be used in future experiments to distinguish between different loss channels. Graphical abstract

von der Linden, J. (ORCID:0000000327477813)↗
DOE OSTI2023

Measurement of ion temperature and toroidal flow during magnetic reconnection with a large guide field

Here, ion temperature and toroidal flow along the guide field direction are measured using a new ion tomographic diagnostic on the Magnetic Reconnection eXperiment (MRX) during magnetic reconnection with a guide field strength of about 1.4 and 2.1 times the strength of the reconnecting component. Strong toroidal flows, beyond what has been measured in anti-parallel and lower guide field conditions on MRX, are observed. Sustained ion heating with no discernible structure within the measurement region is also observed. Probe measurements including Langmuir and Mach probe measurements are made to support the tomographic inversion of line-integrated measurements, as well as to provide local measurements of plasma parameters. Measurements of toroidal velocity and ion temperature are supported with time series data. Energy flow into and out of the X-line region is estimated using a guiding center framework and presented in the Appendix of this manuscript, suggesting an outsized role played by parallel electric field in energizing ions. The guiding center approximation is not well satisfied in the region of interest; however, the estimates provide a springboard for future, further experimentation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Four Channel Time Multiplexed Photonic Doppler Velocimetry using an Optical Switch

Photonic Doppler Velocimetry (PDV) is a diagnostic commonly used in shock physics and dynamic compression experiments to reliably get velocity information from experiments. In PDV systems, a common method of reducing experimental cost is to use time and frequency multiplexing to increase the number of PDV probes. With time multiplexing, interference between probes is a frequent problem. In this report, we look at using a high-speed optical switch to reduce this interference, including measuring the amount of interference generated to determine if it has the potential to affect experiments and integrating a time multiplexing system into an experiment. We find that, when applied to PDV systems, there is approximately (-23.4 ± 0.9) dB of interference measured in the short time Fourier transform between switch inputs. When an optical switch based time multiplexing system was integrated into a dynamic compression experiment, the system was able to successfully combine the signals from four different PDV probes onto a single optical cable without unacceptable levels of interference in the spectrogram. An optical switch based time multiplexing system appears to be a promising method for reducing the cost of fielding larger numbers of PDV probes in an experiment.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Enhanced electro-osmosis in propylene carbonate salt solutions

Properties of solid–liquid interfaces and surface charge characteristics mediate ionic and molecular transport through porous systems, affecting many processes such as separations. Herein, we report experiments designed to probe the electrochemical properties of solid–liquid interfaces using a model system of a single polyethylene terephthalate (PET) pore in contact with aqueous and propylene carbonate solutions of LiClO 4 . First, the existence and polarity of surface charges were inferred from current–voltage curves recorded when a pore was placed in contact with a LiClO4 concentration gradient. Second, the electro-osmotic transport of uncharged polystyrene particles through the PET pore provided information on the polarity and the magnitude of the pore walls’ zeta potential. Our experiments show that the PET pores become effectively positively charged when in contact with LiClO 4 solutions in propylene carbonate, even though in aqueous LiClO 4 , the same pores are negatively charged. Additionally, the electro-osmotic velocity of the particles revealed a significantly higher magnitude of the positive zeta potential of the pores in propylene carbonate compared to the magnitude of the negative zeta potential in water. The presented methods of probing the properties of solid–liquid interfaces are expected to be applicable to a wide variety of solid and liquid systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Tracking nanoparticle growth in pulsed carbon arc discharge

The dynamics of nanoparticle growth in pulsed anodic arc discharge has been studied in time-resolved mode. To this end, a fast moving probe was employed to extract the material generated in a pulsed arc plasma held between two graphite electrodes. The probe motion was synchronized with the pulse phase and the exposure time to the plasma was set to 10 ms. The graphite anode was eroded in a helium atmosphere (300 Torr) by an arc plasma pulsed at 1 Hz with a 10% duty cycle and showing 250 A of peak current. The structure and morphology of the probe depositions were characterized by Raman spectroscopy, scanning electron microscopy, and focused ion beam. A maximal deposition rate of 260 μm/s was measured 5 mm away from the arc core during the active 0.1 s of the pulse. Such a rate yields a growth flux of 1.3 × 10 21 cm –2 s –1 , rich in carbon nanostructures (graphene platelets, nanotubes) with a characteristic aggregate size within 1–10 μm. The deposition during the inactive 0.9 s of the pulse was several orders of magnitude slower and consisted of amorphous carbon traces. Furthermore, the nanoparticle distribution along the collecting probe is correlated with the pulse phase, thereby providing information on particle transport. Pulsed nanosynthesis can be modeled as a periodical growth process, where the volume and propagation velocity of the growth region can be adjusted through modulation of the pulse signal waveform. The proposed model constitutes a suitable framework to investigate the pulsed arc synthesis of nanomaterials with tailored physical and chemical properties.

42 ENGINEERING↗
DOE OSTI2025

Transonic Turbulence and Density Fluctuations in the Near-Sun Solar Wind

We use in situ measurements from the first 19 encounters of Parker Solar Probe and the most recent five encounters of Solar Orbiter to study the evolution of the turbulent sonic Mach number M t (the ratio of the amplitude of velocity fluctuations to the sound speed) with radial distance and its relationship to density fluctuations. We focus on the near-Sun region with radial distances ranging from about 11 to 80 R ⊙ . Our results show that (1) the turbulent sonic Mach number M t gradually moves toward larger values as it approaches the Sun, until at least 11 R ⊙ , where M t is much larger than the previously observed value of 0.1 at and above 0.3 au; (2) transonic turbulence with M t ∼ 1 is observed in situ for the first time and is found mostly near the Alfvén critical surface; (3) Alfvén Mach number of the bulk flow M A shows a strong correlation with the plasma beta, indicating that most of the observed sub-Alfvénic intervals correspond to a low-beta plasma; (4) the scaling relation between density fluctuations and M t gradually changes from a linear scaling at larger radial distances to a quadratic scaling at smaller radial distances; and (5) transonic turbulence is more compressible than subsonic turbulence, with enhanced density fluctuations and slightly flatter spectra than subsonic turbulence. A systematic understanding of compressible turbulence near the Sun is necessary for future solar wind modeling efforts.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

Origin of Electron Boomerang Stripes: Statistical Study

In the outer radiation belt, localized ultralow frequency (ULF) waves can interact with energetic electrons by drift resonance, leading to quasiperiodic oscillations. The oscillations in the pitch angle spectrum can be characterized by either boomerang-shaped or straight stripes. Previous studies have shown that boomerang-shaped stripes evolve from straight ones when electrons drift away from the localized wave interaction region. Based on the time-of-flight technique on the pitch angle-dependent drift velocity, the origin can be remotely identified from the pitch angle dispersion. Here, we report 27 straight stripe events and 86 boomerang-shaped events observed by Van Allen Probes from January 1, 2013, to December 31, 2017. Statistical study shows a good coincidence between the locations of straight ones and traceback regions from boomerang-shaped ones. These locations, mainly located in noon-to-dusk region, coincide well with the plasmaspheric plumes. Thus, localized ULF waves trapped in the plume may result in the preference of localized ULF wave-electron interactions at noon-to-dusk region.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

Synchronization of nonsolitonic Kerr combs

Synchronization is a ubiquitous phenomenon in nature that manifests as the spectral or temporal locking of coupled nonlinear oscillators. In the field of photonics, synchronization has been implemented in various laser and oscillator systems, enabling applications including coherent beam combining and high-precision pump-probe measurements. Recent experiments have also shown time-domain synchronization of Kerr frequency combs via coupling of two separate oscillators operating in the dissipative soliton [i.e., anomalous group velocity dispersion (GVD)] regime. Here, we demonstrate all-optical synchronization of Kerr combs in the nonsolitonic, normal GVD regime in which phase-locked combs with high pump-to-comb conversion efficiencies and relatively flat spectral profiles are generated. Our results reveal the universality of Kerr comb synchronization and extend its scope beyond the soliton regime, opening a promising path toward coherently combined normal GVD Kerr combs with spectrally flat profiles and high comb-line powers in an efficient microresonator platform.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

XRISM Spectroscopy of the Fe Kα Emission Line in the Seyfert Active Galactic Nucleus NGC 4151 Reveals the Disk, Broad-line Region, and Torus

Abstract We present an analysis of the first two XRISM/Resolve spectra of the well-known Seyfert-1.5 active galactic nucleus (AGN) in NGC 4151, obtained in 2023 December. Our work focuses on the nature of the narrow Fe K α emission line at 6.4 keV, the strongest and most common X-ray line observed in AGN. The total line is found to consist of three components. Even the narrowest component of the line is resolved with evident Fe K α ,1 (6.404 keV) and K α ,2 (6.391 keV) contributions in a 2:1 flux ratio, fully consistent with neutral gas with negligible bulk velocity. Subject to the limitations of our models, the narrowest and intermediate-width components are consistent with emission from optically thin gas, suggesting that they arise in a disk atmosphere and/or wind. Modeling the three line components in terms of Keplerian broadening, they are readily associated with (1) the inner wall of the “torus,” (2) the innermost optical “broad-line region” (or “X-ray BLR”), and (3) a region with a radius of r ≃ 100 GM / c 2 that may signal a warp in the accretion disk. Viable alternative explanations of the broadest component include a fast-wind component and/or scattering; however, we find evidence of variability in the narrow Fe K α line complex on timescales consistent with small radii. The best-fit models are statistically superior to simple Voigt functions, but when fit with Voigt profiles the time-averaged lines are consistent with a projected velocity broadening of FWHM = 1600 − 200 + 400 km s − 1 . Overall, the resolution and sensitivity of XRISM show that the narrow Fe K line in AGN is an effective probe of all key parts of the accretion flow, as it is currently understood. We discuss the implications of these findings for our understanding of AGN accretion, future studies with XRISM, and X-ray-based black hole mass measurements.

Audard, Marc (ORCID:000000034721034X)↗
DOE OSTI2022

The Lick AGN Monitoring Project 2016: Velocity-resolved Hβ Lags in Luminous Seyfert Galaxies

We carried out spectroscopic monitoring of 21 low-redshift Seyfert 1 galaxies using the Kast double spectrograph on the 3 m Shane telescope at Lick Observatory from 2016 April to 2017 May. Targeting active galactic nuclei (AGNs) with luminosities of λL$_{λ}$(5100 Å) ≈ 10$^{44}$ erg s$^{-1}$ and predicted Hβ lags of ~20–30 days or black hole masses of 10$^{7}$–10$^{8.5}$M$_{⊙}$, our campaign probes luminosity-dependent trends in broad-line region (BLR) structure and dynamics as well as to improve calibrations for single-epoch estimates of quasar black hole masses. Here we present the first results from the campaign, including Hβ emission-line light curves, integrated Hβ lag times (8–30 days) measured against V-band continuum light curves, velocity-resolved reverberation lags, line widths of the broad Hβ components, and virial black hole mass estimates (10$^{7.1}$–10$^{8.1}$M$_{⊙}$). Our results add significantly to the number of existing velocity-resolved lag measurements and reveal a diversity of BLR gas kinematics at moderately high AGN luminosities. AGN continuum luminosity appears not to be correlated with the type of kinematics that its BLR gas may exhibit. Follow-up direct modeling of this data set will elucidate the detailed kinematics and provide robust dynamical black hole masses for several objects in this sample.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

Shock-induced kinetics and cellular structures of liquid nitromethane detonation

Using a combination of high-speed diagnostics, optical pyrometry, velocimetry and video photography, we examine the spatiotemporal reaction kinetics of a prototypical high-energy explosive, liquid nitromethane (NM), as we drive this high explosive into detonation. The detonations were initiated by powerful shock waves whose durations (4 ns) were shorter than the characteristic time associated with the reaction (7 ns). Simple optical spectroscopy alone cannot characterize the kinetics with high time resolution because the reactants and products are flowing at a high velocity of ~6 km/s (6 µm/ns). Additionally, every detection volume behind the shock front contains material initiated over a range of times. High spatial resolution can be obtained by probing interfaces where the shock enters or breaks out of the NM. In addition, we obtain cellular patterns imprinted on the luminous shock front by the two-stage explosion in NM. These spatiotemporal patterns arise naturally as a result of the asymmetry produced by the moving shock front. In this way the shock front serves as a thin moving intrinsic optical gauge that reports and characterizes the two-stage NM explosion behind the front.

42 ENGINEERING↗