Search NASA⌕ Search

SEARCH · Search NASA

Results for “VTOL AIRCRAFT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS2021

The Causes of Propeller Pitching Moment and the Conditions for its Significance

Recent development of vertical takeoff and landing (VTOL) aircraft has renewed interest in the study of propellers. One metric in particular, the propeller pitching moment, has been observed to be important to VTOL aircraft stability and control in the past. Propellers at angles of attack could not be accurately modeled in generations past due to a lack of computational power, but even with advances in computer technology, modern designers seem to possess insufficient knowledge in this area. In this dissertation, we study the physics behind propeller pitching moment in the context of an isolated propeller and a propeller upstream of a wing. An unsteady 3D vortex lattice method is developed specifically to model propellers at angles of attack and is validated by comparing to high-fidelity CFD analyses. We then use the model to isolate velocity influences to show that the propeller pitching moment is largely caused by two effects: a skewed wake and the presence of wing circulation. Generated maps of propeller pitching moment over a range of operational parameters corresponding to VTOL transition show that the low flight speeds and high angles of attack encountered during transition lead to significant magnitudes of propeller pitching moment that would be difficult to trim using passive methods. Also, derivation of a generalizable metric of significance shows that the peak contribution of propeller pitching moment to aircraft stability is comparable to a longitudinal displacement of the center of gravity by several percent of the wing chord. Finally, we give a concluding discussion on the impact of propeller pitching moment on VTOL aircraft design.

Xiaofan Fei↗
NASA NTRS1972

Pilot/vehicle control optimization using averaged operational mode and subsystem relative performance index sensitivities

A method is presented for designing optimal feedback controllers for systems having subsystem sensitivity constraints. Such constraints reflect the presence of subsystem performance indices which are in conflict with the performance index of the overall system. The key to the approach is the use of relative performance index sensitivity (a measure of the deviation of a performance index from its optimum value). The weighted sum of subsystem and/or operational mode relative performance index sensitivies is defined as an overall performance index. A method is developed to handle linear systems with quadratic performance indices and either full or partial state feedback. The usefulness of this method is demonstrated by applying it to the design of a stability augmentation system (SAS) for a VTOL aircraft. A desirable VTOL SAS design is one that produces good VTOL transient response both with and without active pilot control. The system designed using this method is shown to effect a satisfactory compromise solution to this problem.

Leininger, G. G.↗
NASA NTRS1977

Capabilities of the Navy variable stability X-22A for V/STOL flying qualities R and D

The X-22A V/STOL Flight Research Facility which provides in-flight simulation capability applicable to hover, low speed, and transition flight investigation of fixed wing V/STOL flying is described. The variable stability system, the guidance and display equipment, the data acquisition and processing system, and the ground simulator are included. Research programs involving the STOL flying qualities for landing approach, the control system, display, and guidance requirements for VTOL aircraft instrument approach and landing, and the expansion of the adverse weather operation capabilities of the Navy's VTOL aircraft are briefly summarized.

Aiken, E. W.↗
NASA NTRS1981

Analysis of selected VTOL concepts for a civil transportation mission

As part of defining the needs and technology requirements for VTOL aircraft research and development, the objective of this paper is to study the application of two tilt propulsion concept VTOL aircraft to the business/executive transport mission. The two concepts selected for study are the tilt jet concept utilizing rotating turbofan engines for both vertical lift and cruise thrust, and the tilt rotor concept using relatively low disc loading propellers for hover and cruise. Overall mission costs, including the time-value cost of the executives, was computed for a selected range of mission distances, up to the design mission range of 750 nm (1400 km). The total trip cost was also compared to that of a conventional helicopter/business jet combination for a typical executive transport mission.

Wilson, S. B., III↗
NASA NTRSDate not supplied

Developing Urban Air Mobility Vehicle Models to Support Air Traffic Management Concept Development

To support Urban Air Mobility (UAM) research efforts at NASA, the Airspace Target Generator (ATG) software used in the FutureFlight Central (FFC) air traffic control tower simulator is undergoing updates to support physics-based UAM vehicle models. A process was developed to integrate UAM vertical takeoff and landing (VTOL) aircraft into the fixed-wing ATG modeling environment without significant change to the underlying equations of motion and vehicle model database. The VTOL aircraft models were converted from a six degrees-of-freedom (6-DOF) representation into a four degrees-of-freedom (4-DOF) representation for integration within ATG. Three vehicle designs from the NASA Revolutionary Vertical-Lift Technologies (RVLT) project were selected: a lift-plus-cruise (LPC) aircraft model and quadrotor, electric-powered (QEP) 1-seater and 6-seater models. With the LPC model comprised of a nonlinear force and moment build-up, and the QEP models comprised of linearized stability derivatives, two separate processes were developed to convert the lift, drag, and propulsion characteristics of each model into the ATG model database. Key aircraft performance characteristics including climb, cruise, and descent performance were preserved during the conversion process. Because ATG simulates fixed-wing aircraft through ground taxi and takeoff to approach and landing, acceleration command algorithms were developed to model the vertical takeoff and vertical landing phase of UAM operations. A strategy was then developed to transition the aircraft model to- and from- the new control mode.

urban air mobility↗
NASA NTRS2024

An Annoyance Model for Urban Air Mobility Vehicle Noise in the Presence of a Masker

Proposed Urban Air Mobility (UAM) operations offer an alternative to road and rail traffic for local and regional movement of people and goods. To allow for large-scale adoption of UAM vertical takeoff and landing (VTOL) aircraft, it is critical to predict human annoyance response to the acoustic noise generated by these vehicles. We propose a model that predicts an individual’s perceived level of annoyance when presented with UAM VTOL aircraft noise in the context of a representative masking noise. The annoyance model is based on the psychoacoustic annoyance model of Fastl and Zwicker (Zwicker and Fastl, 1999), with an additional tonality term based on subjective testing of UAM sound quality (Boucher, et al., 2023). The model also predicts changes in annoyance when UAM noise is masked by a background sound, based on subjective evaluation of detection, noticeability, and annoyance of noise in the presence of a masker.

Noise↗
NASA NTRS2018

Adventures in Low Disc Loading VTOL Design

This memoir covers the first eight years of my 37 year career in VTOL aircraft design. It starts with family and how I came to be an engineer with a passion for aviation and a desire to make a difference. At MIT I acquired a solid understanding of basic physics, learned the basics of the various engineering disciplines and gained design experience. After over a decade on the East Coast I was homesick for Northern California. I decided to take a chance on working for the government instead of industry in order to return home. I was hired by Dr. Richard M. Carlson in March 1975 and joined a wonderful Army/NASA technical environment. The Interservice Helicopter Commonality Study was an important introduction to Joint Service aircraft design. The Advanced Attack Helicopter Source Selection Evaluation Board was an opportunity to learn acquisition system fundamentals and to lead a small team in a major technical evaluation. The Advanced Scout Helicopter Concept Formulation was an opportunity to learn how an aircraft development program is created and it formed a partnership between Dr. Carlson's Labs and Charlie Crawford's Development and Qualification directorate. The Army was Executive Service for the first year (1982) of the Joint Services Advanced Vertical Lift Aircraft (JVX) program. The JVX Joint Technology Assessment concluded that there was at least one design configuration, the tilt rotor, which could satisfy all JVX mission requirements with a high degree of inter-service commonality. The Navy became Executive Service at the end of the year and promptly released a JVX RFP to industry. This RFP resulted in the V-22 Osprey tilt rotor as the third type of VTOL aircraft to enter production and service. I was very lucky to have a useful role early in this program.

VTOL Design↗
NASA NTRS1982

Lateral control system design for VTOL landing on a DD963 in high sea states

The problem of designing lateral control systems for the safe landing of VTOL aircraft on small ships is addressed. A ship model is derived. The issues of estimation and prediction of ship motions are discussed, using optimal linear linear estimation techniques. The roll motion is the most important of the lateral motions, and it is found that it can be predicted for up to 10 seconds in perfect conditions. The automatic landing of the VTOL aircraft is considered, and a lateral controller, defined as a ship motion tracker, is designed, using optimal control techniqes. The tradeoffs between the tracking errors and the control authority are obtained. The important couplings between the lateral motions and controls are demonstrated, and it is shown that the adverse couplings between the sway and the roll motion at the landing pad are significant constraints in the tracking of the lateral ship motions. The robustness of the control system, including the optimal estimator, is studied, using the singular values analysis. Through a robustification procedure, a robust control system is obtained, and the usefulness of the singular values to define stability margins that take into account general types of unstructured modelling errors is demonstrated. The minimal destabilizing perturbations indicated by the singular values analysis are interpreted and related to the multivariable Nyquist diagrams.

Bodson, M.↗
NASA NTRS2016

Range and Endurance Tradeoffs on Personal Rotorcraft Design

Rotorcraft design has always been a challenging tradeoff among overall size, capabilities, complexity, and other factors based on available technology and customer requirements. Advancements in propulsion, energy systems and other technologies have enabled new vehicles and missions; complementary advances in analysis methods and tools enable exploration of these enhanced vehicles and the evolving mission design space. A system study was performed to better understand the interdependency between vehicle design and propulsion system capabilities versus hover / loiter requirements and range capability. Three representative vertical lift vehicles were developed to explore the tradeoff in capability between hover efficiency versus range and endurance capability. The vehicles were a single-main rotor helicopter, a tilt rotor, and a vertical take-off and landing (VTOL) aircraft. Vehicle capability was limited to two or three people (including pilot or crew) and maximum range within one hour of flight (100-200 miles, depending on vehicle). Two types of propulsion and energy storage systems were used in this study. First was traditional hydrocarbon-fueled cycles (such as Otto, diesel or gas turbine cycles). Second was an all-electric system using electric motors, power management and distribution, assuming batteries for energy storage, with the possibility of hydrocarbon-fueled range extenders. The high power requirements for hover significantly reduced mission radius capability. Loiter was less power intensive, resulting in about 1/2 the equivalent mission radius penalty. With so many design variables, the VTOL aircraft has the potential to perform well for a variety of missions. This vehicle is a good candidate for additional study; component model development is also required to adequately assess performance over the design space of interest.

systems analysis↗
NASA NTRS2016

Range and Endurance Tradeoffs on Personal Rotorcraft Design

Rotorcraft design has always been a challenging tradeoff among overall size, capabilities, complexity, and other factors based on available technology and customer requirements. Advancements in propulsion, energy systems and other technologies have enabled new vehicles and missions; complementary advances in analysis methods and tools enable exploration of these enhanced vehicles and the evolving mission design space. A system study was performed to better understand the interdependency between vehicle design and propulsion system capabilities versus hover loiter requirements and range capability. Three representative vertical lift vehicles were developed to explore the tradeoff in capability between hover efficiency versus range and endurance capability. The vehicles were a single-main rotor helicopter, a tilt rotor, and a vertical take-off and landing (VTOL) aircraft. Vehicle capability was limited to two or three people (including pilot or crew) and maximum range within one hour of flight (100-200 miles, depending on vehicle). Two types of propulsion and energy storage systems were used in this study. First was traditional hydrocarbon-fueled cycles (such as Otto, diesel or gas turbine cycles). Second was an all-electric system using electric motors, power management and distribution, assuming batteries for energy storage, with the possibility of hydrocarbon-fueled range extenders. The high power requirements for hover significantly reduced mission radius capability. Loiter was less power intensive, resulting in about 12 the equivalent mission radius penalty. With so many design variables, the VTOL aircraft has the potential to perform well for a variety of missions. This vehicle is a good candidate for additional study; component model development is also required to adequately assess performance over the design space of interest.

systems analysis↗
NASA NTRS1960

Thrust Characteristics of Multiple Lifting Jets in Ground Proximity

An investigation has been made to determine the thrust characteristics within ground proximity of a series of models which might represent vertical take-off-and-landing (VTOL) aircraft with multiple exit jet engines exhausting vertically downward beneath a lifting surface. Variations in simulated engine configurations were provided by a series of nozzle insert plugs in which the number of jet exits, located symmetrically on a fixed circle, was varied, or the diameter of the circle was varied for a given number of jet exits. represent lifting surfaces, and high-pressure air was used to simulate jet-engine exhaust. Plywood plates were used to The results of the investigation showed that increasing the number of exits, such that an annular jet configuration was approached, provided more favorable thrust characteristics within ground proximity than any other variation in the geometry of these multiple jets. Tests of a configuration with two nozzles approximating a fan-in-wing VTOL aircraft with fans located at different spanwise locations indicated that the augmentation in thrust within ground proximity was greater for the arrangement with the more inboard location of the nozzles.

Davenport, Edwin E.↗
NASA NTRS1979

Evaluation of the navigation performance of shipboard-VTOL-landing guidance systems

The objective of this study was to explore the performance of a VTOL aircraft landing approach navigation system that receives data (1) from either a microwave scanning beam (MSB) or a radar-transponder (R-T) landing guidance system, and (2) information data-linked from an aviation facility ship. State-of-the-art low-cost-aided inertial techniques and variable gain filters were used in the assumed navigation system. Compensation for ship motion was accomplished by a landing pad deviation vector concept that is a measure of the landing pad's deviation from its calm sea location. The results show that the landing guidance concepts were successful in meeting all of the current Navy navigation error specifications, provided that vector magnitude of the allowable error, rather than the error in each axis, is a permissible interpretation of acceptable performance. The success of these concepts, however, is strongly dependent on the distance measuring equipment bias. In addition, the 'best possible' closed-loop tracking performance achievable with the assumed point-mass VTOL aircraft guidance concept is demonstrated.

Mcgee, L. A.↗
NASA NTRS1962

Linearized Theory of Wind-tunnel Jet-boundary Corrections and Ground Effect for VTOL-STOL Aircraft

A linearized theory is developed to obtain interference factors for wind tunnels and ground effect. The calculated results, presented in tabular form in NASA Technical Notes D-933, D-934, D-935, and D-936, indicate that the degree to which the wake is deflected downward has a primary effect on the magnitude of the interference. When the wake is undeflected the corrections are essentially the same as those of classical theory. When the wake is deflected severely downward, the corrections are primarily determined by the floor of the wind tunnel. Under these conditions, the corrections are, in general, much larger than those given by previously available results. Because of deformations at the lower boundary of the jet, the corrections for an open wind tunnel are uncertain. Testing at low speeds and high lift coefficients in open wind tunnels, therefore, is not recommended. Although the theory is developed expressly for single-element, vanishingly small models, methods, with sample calculations, are given for extending the results to multielement and finite span models. The theory is at least partially verified by available test data; however, complete verification would require a substantially more detailed experimental study.

V/STOL aircraft↗
NASA NTRS2010

Converting a C-130 Hercules into a Compound Helicopter: A Conceptual Design Study

This study presents the performance and weight changes for a Compound C-130 as compared to the Baseline C-130H Hercules, using NDARC as the primary analysis tool. First, the C-130H was modeled within NDARC, from which performance at various conditions and a parametric weight statement were generated. Then, the C-130H NDARC file was modified to represent the Compound C-130, which was then put through the same performance analysis as the C-130H. A parametric weight statement was also calculated for the Compound C-130, which allowed for comparison to the C-130H. As part of the modeling of the Compound C-130, a Rotor Design Spreadsheet was created that would allow the direct calculation of the weight of the main rotors being added. Using composite materials led to considerable weight savings for both the rotor system and the hub weights. These weight savings are reflected in the NDARC Technology Factors which were determined to be 0.71 and 0.5 for the rotor blades and the hub/hinge system, respectively. Such Technology Factors suggest that using composites for other components could drastically lighten the Operating Empty Weight of the aircraft. The weight statements show the weights for each of the components on each aircraft. It is quite evident that the Compound C-130 has a higher Operating Empty Weight due to the addition of the two main rotors and a drive system to connect each engine group on the wing tips. Upon further analysis, the main weight driver is the drive system. While the main rotor/hub/hinge weight increase is to be expected, the weight increase due to the transmission drive and gear boxes are cause for concern. Unless a method can be found of reducing the weight of the drive system, the weight penalty makes the Compound a C-130 an inefficient aircraft in terms of payload/fuel capacity. Possible solutions are either off-loading some of the power requirements through the drive system or using composite materials in the construction of the drive system. The performance of the Compound C-130 versus the C-130H shows a clear need for more powerful engines than are currently present on the C-130H. This would also adversely affect the Operating Empty Weight since a larger power plant requires more weight. However, one advantage that the Compound C-130 presents is the ability to hover and operate at low speeds in Helicopter Mode. While the C-130H is unable to travel at speeds lower than its stall speed, the Compound C-130 is able to hover using the main rotors. Thus, the Compound C-130 is able to operate independent of runways, let alone the condition of the nearest runway. Ultimately, the Compound C-130 is an effective aircraft in theaters requiring VTOL aircraft due to geographical considerations in terms or performance. Unfortunately, the weight penalty associated with converting the C-130H to a Compound C-130 suggests that further work in the area of the drive systems is required.

Kottapalli, Anjaney P.↗