Search NASA⌕ Search

SEARCH · Search NASA

Results for “Welding Simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

USAMP Low-Cost Mg Sheet Component Development and Demonstration Project

The overarching objective of this USAMP project was to develop and demonstrate door panels made from magnesium (Mg) sheet with a cost penalty over conventional steel stampings of no more than $\$5.50$/kg saved. The technical approach integrated experiments with advanced computational tools based on Integrated Computational Materials Engineering (ICME) methods to develop new alloy chemistries and their thermomechanical processing that promise improved formability and lower forming temperatures. A penultimate task before finally forming the stampings was to incorporate actual microstructure into models that would enable formability simulations. This approach would, for the first time, account for individual magnesium grains moving in an anisotropic fashion unlike that for aluminum or steel that have isotropic properties upon which the current simulation tools are based. In separate activities, new coatings and lubricants to facilitate forming and improved corrosion protection and joining strategies, were developed to ensure that the door could be produced with stated product requirements. A technical cost model, which included parts production, assembly, and paint for a door specifically designed for Mg sheet, showed the cost penalty to be between $\$4.26$ to $\$6.60$/kg saved, which enveloped the project’s cost targets. The cost of the coated Mg sheet was identified as the key driver for the cost penalty. The mass of the Mg-intensive door was 7.9 kg, which was 54% less than the baseline steel door.

36 MATERIALS SCIENCE↗

Low-Cost Magnesium Alloy Sheet Component Development and Demonstration Project

The overarching objective of this USAMP project was to develop and demonstrate door panels made from magnesium (Mg) sheet with a cost penalty over conventional steel stampings of no more than $5.50/kg saved. The technical approach integrated experiments with advanced computational tools based on Integrated Computational Materials Engineering (ICME) methods to develop new alloy chemistries and their thermomechanical processing that promise improved formability and lower forming temperatures. A penultimate task before finally forming the stampings was to incorporate actual microstructure into models that would enable formability simulations. This approach would, for the first time, account for individual magnesium grains moving in an anisotropic fashion unlike that for aluminum or steel that have isotropic properties upon which the current simulation tools are based. In separate activities, new coatings and lubricants to facilitate forming and improved corrosion protection and joining strategies, were developed to ensure that the door could be produced with stated product requirements. A technical cost model, which included parts production, assembly, and paint for a door specifically designed for Mg sheet, showed the cost penalty to be between 4.26 USD to 6.60 USD/kg saved, which enveloped the project’s cost targets. The cost of the coated Mg sheet was identified as the key driver for the cost penalty. The mass of the Mg-intensive door was 7.9 kg, which was 54% less than the baseline steel door.

36 MATERIALS SCIENCE↗

Characterization of the Fusion Zone in Laser Beam Welds on SS304L

Designing a welded joint requires consideration of the welding process, component/assembly structure and weld geometry, material composition, properties, and desired joint performance. The designer must also specify a set of acceptance criteria used to evaluate the welds. This study was conducted to support the design team responsible for specifying the spot weld profile by investigating the relationship between weld process parameters and the weld geometry and properties to further inform design optimization. The subjects of this study are two thin stainless steel 304L (SS304L) components joined by Laser Beam Welding (LBW). The components are the Housing, which contains flexible circuitry, and the Cover that protects the circuitry during handling, installation, and under service loads. Figure 1 illustrates coupon versions of the Cover and Housing used to simulate the interface between these components for weld testing. These coupon representations of assembly components were designed to match the material and relevant geometry related to the welded joint while other features not relevant to the welded joint are excluded.The objective of this study was to characterize the sensitivity of the weld geometry and mechanical properties to the input weld parameters to inform further Finite Element Analysis (FEA) efforts in balancing joint strength against assembly deformation caused by the welding process. Characterization was accomplished by varying laser welding parameters around the current design values and measuring weld geometry on the cross-sections. Nanoindentation with a spherical and flat-ended tip was used on polished section cuts of the weld to obtain direct estimates of the stress-strain response of the Fusion Zone (FZ) for comparison to the Base Metal (BM).

42 ENGINEERING↗

Develop a Fast Analysis Solver for Welding Sequence Optimization

During the shipbuilding manufacturing process, materials are exposed to significant stresses, as induced both thermally and mechanically, that alter the intended design and significantly affect the production schedule, labor hours (fitting, welding, rework, etc.), and material structural performance. The type and magnitude of deformation of a given structure depends on many factors such as the material, thickness and quality of components, the process heat input, preheat and inter-pass temperatures, type and size of welds, welding sequence and direction, location, sequence, and degree of fixturing. Numerical simulations using finite element analysis (FEA) have long been used to analyze welding-induced structural distortion. For large assemblies, transient thermal elastic-plastic analysis (TEPA) can take days or weeks to run, and optimization of welding sequence is not feasible. Simplified analysis methods were developed to reduce computational time. However, it is challenging to use these techniques to fully optimize welding sequencing because of their applied simplifications in modeling weld details. A fast analysis solver that could be used by the shipbuilding industry is being developed for optimizing welding sequences by taking full advantage of modern GPU-based HPC hardware and incorporating patented acceleration schemes. The accelerated processing factors are up to 2200 times greater for large, multi-pass welded structures.

Yang, Yu-Ping↗

Optimization of Tensile and Corrosion Properties of Dissimilar Friction Stir Welded AA2024-7075 Joints

In this work, we performed some joining experiments of dissimilar aluminum alloys AA2024-T351 and AA7075-T651 using friction stir welding (FSW) technique with different process parameters (rotational speed, welding speed and plunge depth). Response surface methodology based on a central composite rotatable design was used to establish the mathematical models predicting the tensile properties and corrosion rate of dissimilar FSW joints with some high confidence level. Analysis of variance method was employed to verify the developed models. Besides, the influences of FSW process parameters on tensile and corrosion properties of joints were analyzed. In order to obtain a desirable combination property of the dissimilar FSW joints, the optimum process parameters after experimental verification were proposed as: rotational speed 1495 rev/min, welding speed 187 mm/min and plunge depth 0.03 mm. This verification illustrated that the developed models are appropriate for the modeling and optimization of process.

36 MATERIALS SCIENCE↗

Quarterly Management Document – FY22, 1st Quarter, Multi-pass Hybrid Laser Arc Welding of Alloy 740H

This report summarizes the progress made on the project during the first quarter of FY22. The model for deep penetration laser welding continues to be developed to understand and mitigate cracking issues associated with laser welding Alloy 740H. The effects of laser wobble on laser welding of this alloy are also being developed. Additionally, the short-term creep behavior of welds made by various hybrid laser arc parameters has been obtained and the results indicate they are comparable to welds made by conventional gas tungsten arc welding which is a factor 2 slower than the hybrid welds. Additionally, the creep behavior of laser-only welds is also consistent with conventional gas tungsten arc welds as well as the hybrid laser arc welds made under this project. However, the creep rate of the laser-only welds is much higher than that observed in the hybrid laser arc welded specimens. This is most likely due to the narrower weld produced by laser-only welding compared to hybrid laser arc welding and, thus, the higher creep rate of laser-only welded creep specimens is likely a result of the increased fraction of base metal (which exhibits a higher creep rate than weld metal) contained within the gage section of the creep specimen. Creep rupture lifetimes were all about the same for both laser-only and hybrid laser arc welded specimens and consistent with the creep rupture lifetime of conventional gas tungsten arc welded creep specimens.

36 MATERIALS SCIENCE↗

On residual stress analysis and microstructural evolution for stainless steel type 304 spent nuclear fuel canisters weld joint: Numerical and experimental studies

Chloride-induced stress corrosion cracking (CISCC) in the weldments of austenitic stainless steel canisters is one of the primary safety concerns during the dry storage of used nuclear fuel at Independent Spent Fuel Storage Installations in coastal areas. In order to evaluate the CISCC behavior in the canister, a 3D sequentially coupled thermo-mechanical finite element model was built to simulate the residual stresses induced by two intersecting longitudinal and circumferential multi-pass welds in austenitic stainless steel mockup canister. Weld-induced residual stresses from simulation were in good agreement with the experimental measurement results by deep-hole drilling and contour methods. Through-wall high tensile axial and hoop stresses were observed in both the fusion zone and heat affected zone (HAZ) in the longitudinal and circumferential weld, respectively. On the other hand, the microstructure within the weldments of 304 stainless steel mockup was characterized using optical microscopy, scanning electron microscopy, electron back-scattered diffraction and energy dispersive X-ray spectroscopy methods. A few amount of MnS inclusions in both the base metal and HAZ, and a lot of (Mn,Si) x O y inclusions in the fusion zone were found. Meanwhile, there is some α'-martensite in the base metal, while the martensite was reversed in the HAZ. In the fusion zone, there is a lot of δ-ferrite. The martensite reversion phenomenon was also verified by the combination of Feritscope test and thermal simulation, which could predict a martensite reversion temperature as 400C°. The welding residual stresses and microstructure analysis results could offer the instructive information for the prediction of CISCC behavior of the spent nuclear fuel canisters.

36 MATERIALS SCIENCE↗

Effect of thermal and thermo-mechanical cycling on the boron segregation behavior in the coarse-grained heat-affected zone of low-alloy steel

The boron segregation behavior in the coarse-grained heat-affected zone (CGHAZ) of 10 ppm boron-added low-alloy steel during the welding cycle was investigated by taking the changes in the microstructure and hardness into account. Various CGHAZs were simulated with a Gleeble system as a function of the heat input and external stress, and the boron segregation behavior was analyzed by secondary ion mass spectrometry (SIMS) and particle tracking autoradiography (PTA). The segregation of boron was found to initially increase, and then decrease with an increase in the heat input. This is believed to be due to the back-diffusion of boron with an increase in the exposure time at high temperature after non-equilibrium grain boundary segregation. The grain boundary segregation of boron could be decreased by an external stress applied during the welding cycle. Such behavior may be due to an increase in the grain boundary area as a result of the grain size reduction induced by the external stress. - Highlights: • Boron segregation behavior in the CGHAZ of low-alloy steel during a welding cycle was investigated. • Various CGHAZs were simulated with a Gleeble system as a function of the heat input and external stress. • Boron segregation behavior was analyzed using SIMS and PTA techniques.

36 MATERIALS SCIENCE↗

Accurate modelling of anisotropic effects in austenitic stainless steel welds

The ultrasonic inspection of austenitic steel welds is challenging due to the formation of highly anisotropic and heterogeneous structures post-welding. This is due to the intrinsic crystallographic structure of austenitic steel, driving the formation of dendritic grain structures on cooling. The anisotropy is manifested as both a ‘steering’ of the ultrasonic beam and the back-scatter of energy due to the macroscopic granular structure of the weld. However, the quantitative effects and relative impacts of these phenomena are not well-understood. A semi-analytical simulation framework has been developed to allow the study of anisotropic effects in austenitic stainless steel welds. Frequency-dependent scatterers are allocated to a weld-region to approximate the coarse grain-structures observed within austenitic welds and imaged using a simulated array. The simulated A-scans are compared against an equivalent experimental setup demonstrating excellent agreement of the Signal to Noise (S/N) ratio. Comparison of images of the simulated and experimental data generated using the Total Focusing Method (TFM) indicate a prominent layered effect in the simulated data. A superior grain allocation routine is required to improve upon this.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Influence of the Vapor Channel in Deep Laser Welding

The physical processes associated with deep welding are analyzed. A two-dimensional numerical model is proposed for the interaction of the laser beam with the medium in the vapor channel. The following processes are considered: heat and mass transfer; absorption and reradiation of the beam’s energy by the plasma; interaction of the plasma with the channel walls; and heat transfer to the cold sample. The model establishes a quantitative relation between the welding conditions and the results of butt welding. That decreases the expenditures in the development of laser-welding processes.

42 ENGINEERING↗

Atomistic simulations of nanowelding of single-crystal and amorphous gold nanowires

The mechanism and quality of the welding of single-crystal (SC) and amorphous gold nanowires (NWs) with head-to-head contact are studied using molecular dynamics simulations based on the second-moment approximation of the many-body tight-binding potential. The results are discussed in terms of atomic trajectories, slip vectors, stress, and radial distribution function. Simulation results show that the alignment for the amorphous NWs during welding is easier than that for the SC NWs due to the former's relatively stable geometry. A few dislocations nucleate and propagate on the (111) close-packed plane (slip plane) inside the SC NWs during the welding and stretching processes. During welding, an incomplete jointing area first forms through the interactions of the van der Waals attractive force, and the jointing area increases with increasing extent of contact between the two NWs. A crystallization transition region forms in the jointing area for the welding of SC-amorphous or amorphous-SC NWs. With increasing interference, an amorphous gold NW shortens more than does a SC gold NW due to the former's relatively poor strength. The pressure required for welding decreases with increasing temperature.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Comparative study of microstructure and properties of low-alloy-steel/nickel-based-alloy interfaces in dissimilar metal weld joints prepared by different GTAW methods

Highlights: • Number of type I and type II boundaries: H-DMWJ > C-DMWJ > W-DMWJ. • Width carbon depleted zones and carbon enriched zones: H-DMWJ > C-DMWJ > W-DMWJ. • Type I and type II boundaries are susceptible to SCC and cracked during mechanical bending. • C-DMWJ has the best performance while H-DMWJ has the worst one. - Abstract: Low-alloy-steel/buttering (or welding) metal interfaces in safe-end dissimilar metal weld joints (DMWJs) at nuclear power plants are weak parts. To optimize the quality of the safe-end DMWJs used for the construction of domestic nuclear power plants and to improve the welding productivity, a series of DMWJs in full-size have been manufactured by using different gas tungsten arc welding (GTAW) methods. The microstructure, chemical composition distribution and local properties across the SA508/52(M) interfaces in these DMWJs are studied. The high heat input and long high temperature duration during hot-wire GTAW process promote the carbon diffusion and grain boundary migration and hence the DMWJ by hot-wire GTAW has the largest amount of type I and type II boundaries and the widest carbon depleted zones and carbon enriched zones, which resulting in the worst performance among the DMWJs in simulated primary water. Type I and type II boundaries are high angle random grain boundaries (RGBs) and Cr-depleted zones are found along type II boundaries resulting in their high susceptibility to SCC. In addition, these boundaries are prone to be cracked during mechanical bending process.

36 MATERIALS SCIENCE↗

ExaAM: Metal additive manufacturing simulation at the fidelity of the microstructure

Additive manufacturing (AM), or 3D printing, of metals is transforming the fabrication of components, in part by dramatically expanding the design space, allowing optimization of shape and topology. However, although the physical processes involved in AM are similar to those of welding, a field with decades of experimental, modeling, simulation, and characterization experience, qualification of AM parts remains a challenge. The availability of exascale computational systems, particularly when combined with data-driven approaches such as machine learning, enables topology and shape optimization as well as accelerated qualification by providing process-aware, locally accurate microstructure and mechanical property models. We describe the physics components comprising the Exascale Additive Manufacturing simulation environment and report progress using highly resolved melt pool simulations to inform part-scale finite element thermomechanics simulations, drive microstructure evolution, and determine constitutive mechanical property relationships based on those microstructures using polycrystal plasticity. We report on implementation of these components for exascale computing architectures, as well as the multi-stage simulation workflow that provides a unique high-fidelity model of process–structure–property relationships for AM parts. In addition, we discuss verification and validation through collaboration with efforts such as AM-Bench, a set of benchmark test problems under development by a team led by the National Institute of Standards and Technology.

3D printing↗

A robust process-structure model for predicting the joint interface structure in impact welding

The impact welding is gaining popularity in joining of dissimilar metals as any intermetallics are often very thin or discontinous with little to no heat affected zone resulting from the process. This work focuses on a recently developed impact welding technique, known as the Vaporizing Foil Actuator Welding (VFAW), which uses the pressure created from the electrically driven rapid vaporization of a thin metallic conductor to drive the flyer. A typical characteristic of an impact-welded joint is the wavy weld interface which is attributed to the complex interfacial kinematics resulting from the high-speed oblique impact of the metal plates. A numerical simulation framework based on the finite element method (FEM) with Eulerian formalism is developed to model the high-speed impact between the metal plates. The model accounts for the thermomechanical interactions in the process and captures the complex interfacial deformations. A thorough validation of the model is achieved by comparing the wave characteristics obtained from numerical simulations with the experimental results from vaporizing foil actuator welding. The amplitude and wavelength of the interfacial waves and the resulting joint microstructure is shown to be strongly dependent on the process conditions and the specific material system, which is well captured by the model.

42 ENGINEERING↗

Metal Big Area Additive Manufacturing: Process Modeling and Validation

Metal Big Area Additive Manufacturing (mBAAM) is a new additive manufacturing (AM) technology for printing large-scale 3D objects. mBAAM is based on the gas metal arc welding process and uses a continuous feed of welding wire to manufacture an object. An electric arc forms between the wire and the substrate, which melts the wire and deposits a bead of molten metal along the predetermined path. In general, the welding process parameters and local conditions determine the shape of the deposited bead. The sequence of the bead deposition and the corresponding thermal history of the manufactured object determine the long range effects, such as thermal-induced distortions and residual stresses. Therefore, the resulting performance or final properties of the manufactured object are dependent on its geometry and the deposition path, in addition to depending on the basic welding process parameters. Physical testing is critical for gaining the necessary knowledge for quality prints, but traversing the process parameter space in order to develop an optimized build strategy for each new design is impractical by pure experimental means. Computational modeling and optimization may accelerate development of a build process strategy and saves time and resources. Because computational modeling provides these opportunities, we have developed a physics-based Finite Element Method (FEM) simulation framework and numerical models to support the mBAAM process s development and design. In this paper, we performed a sequentially coupled heat transfer and stress analysis for predicting the final deformation of a small rectangular structure printed using the mild steel welding wire. Using the new simulation technologies, material was progressively added into the FEM simulation as the arc weld traversed the build path. In the sequentially coupled heat transfer and stress analysis, the heat transfer was performed to calculate the temperature evolution, which was used in a stress analysis to evaluate the residual stresses and distortions. In this formulation, we assume that physics is directionally coupled, i.e. the effect of stress of the component on the temperatures is negligible. The experiment instrumentation (measurement types, sensor types, sensor locations, sensor placements, measurement intervals) and the measurements are presented. The temperatures and distortions from the simulations show good correlation with experimental measurements. Ongoing modeling work is also briefly discussed.

Additive Manufacturing↗

Effect of Delta Ferrite on Microstructure and Mechanical Properties of High-Chromium Martensitic Steel

The fusion zone of modified 9Cr-1Mo steel experiencing a peak temperature of 1450 °C and varying cooling rates between 1 and 40 °C/s from the peak temperature is simulated using Gleeble thermal simulator. Mechanical properties of the simulated samples are assessed by ball indentation and impression creep tests. The study evaluates the effect of cooling rate on volume fraction, morphology of retained delta ferrite in the simulated partially melted zone of an autogenous weld, and subsequently its effect on the mechanical properties of this zone. With varying cooling rate, volume fraction of delta ferrite does not change much; however, its morphology changes from polygonal island to grain boundary network in case of excessive slow cooling (1 °C/s). Morphological variation of delta ferrite affects the creep properties of this zone. Partially melted zone, which is cooled at 1 °C/s with delta ferrite present in the interdendritic regions, exhibits maximum creep strain and creep strain rate.

36 MATERIALS SCIENCE↗

Towards Polymer-Free, Femto-Second Laser-Welded Glass/Glass Solar Modules

This project explores the use of femto-second (fs) lasers to form glass-to-glass welds for hermetically sealed, polymer-free solar modules. Low iron solar glass coupons were welded together without the use of glass filler using a fs laser with dedicated optics to elongate the focal plane parallel to the incident beam. The resulting welds were then stress tested to failure to reveal the critical stress intensity factor, KIc. These values were used in a structural mechanics model of a 1 m by 2 m glass/glass module under a simulated static load test. The results show that the fs laser welds are strong enough for a suitably framed module to pass the IEC 61215 static load test with a load of 5400 Pa. Key to this finding is that the module must be framed and braced, and the glass must be ribbed to allow pockets for the cells and welds inside the border of the module. The result is a module design that is completely polymer-free, hermetically sealed, has improved thermal properties, and is easily recycled.

femto-second laser welded↗

Molecular dynamics study on interface formation and bond strength of impact-welded Mg-steel joints

It was recently demonstrated that the vaporizing foil actuator welding (VFAW) method can directly join immiscible magnesium and steel alloys without coating or a third chemical element based intermetallic compound layer. The VFAW Mg/steel joint exhibits a mixed interface layer of up to 200μm thickness consisting of Mg matrix and Fe particles. Computer simulations have suggested the formation of the interlayer is from the high-velocity frictional shearing between the Mg/steel substrates during the oblique impact in the VFAW process. This paper investigates the formation of Mg-Fe interlayer under VFAW condition with different shearing velocities using molecular dynamics (MD) model, and studies the bonding strength under different scenarios. Finally, the results elucidate the critical role of shearing velocity and surface roughness in achieving Mg/Fe joint.

36 MATERIALS SCIENCE↗