Search NASA⌕ Search

SEARCH · Search NASA

Results for “Wing body configuration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

The prediction of pressure distributions on an arrow-wing configuration including the effect of camber, twist, and a wing fin

Wind tunnel tests of an arrow wing body configuration consisting of flat, twisted, and cambered twisted wings were conducted at Mach numbers from 0.40 to 2.50 to provide an experimental data base for comparison with theoretical methods. A variety of leading and trailing edge control surface deflections were included in these tests, and in addition, the cambered twisted wing was tested with an outboard vertical fin to determine its effect on wing and control surface loads. Theory experiment comparisons show that current state of the art linear and nonlinear attached flow methods were adequate at small angles of attack typical of cruise conditions. The incremental effects of outboard fin, wing twist, and wing camber are most accurately predicted by the advanced panel method PANAIR. Results of the advanced panel separated flow method, obtained with an early version of the program, show promise that accurate detailed pressure predictions may soon be possible for an aeroelasticity deformed wing at high angles of attack.

Bobbitt, P. J.↗
NASA NTRS1959

An Investigation of the Pitching-Moment Contribution of a High Horizontal Tail on an Unswept-Wing and Body Combination at Mach Numbers from 0.80 to 1.40

An investigation has been conducted to determine the effects of a high positioned horizontal tail on a wing-body configuration having a thin unswept wing of aspect ratio 3.09. Lift and pitching-moment coefficients were obtained for Mach numbers from 0.80 to 1.40 at Reynolds numbers of 1.0 and 1.5 million and for angles of attack to 20 deg. An experimental study of the pitching-moment contribution of the horizontal tail indicated that the marked destabilizing effect of the horizontal tail at high angles of attack for Mach numbers of 0.80 to 1.00 was associated with the formation of completely separated flow on the upper surface of the wing. Computations of the interference effects of the wing-body combination on the tail for Mach numbers of 0.80 and 0.94 and high angles of attack confirmed this conclusion. For a Mach number of 1.40, and high angles of attack, computations disclosed that the destabilizing effect primarily resulted from the trailing vortices of the wing. Two modifications to the basic wing plan form, which consisted of chord extensions, were generally unsuccessful in reducing the destabilizing contributions of the horizontal tail at high angles of attack.

Lippmann, Garth W.↗
NASA NTRS1972

Numerical computation of multishocked, three-dimensional supersonic flow fields with real gas effects.

A computational procedure is presented which is capable of determining the supersonic flow field surrounding three-dimensional wing-body configurations such as a delta-wing space shuttle. The governing equations in conservation-law form are solved by a finite difference method using a second-order noncentered algorithm between the body and the outermost shock wave, which is treated as a sharp discontinuity. Secondary shocks which form between these boundaries are captured automatically, and the intersection of these shocks with the bow shock posed no difficulty. Resulting flow fields about typical blunt nose shuttle-like configurations at angle of attack are presented. The differences between perfect and real gas effects for high Mach number flows are shown.

Kutler, P.↗
NASA NTRS1983

Aeropropulsive characteristics of twin single-expansion-ramp vectoring nozzles installed with forward-swept wings and canards

The Langley 16 foot transonic tunnel was used to determine the aeropropulsive characteristics of twin single-expansion-ramp vectoring nozzles installed in a wing-body configuration with forward-swept wings. The configuration was tested with and without fixed canards. The test conditions included free-stream Mach numbers of 0.60, 0.90, and 1.20. The model angle of attack ranged from -2 deg to 14 deg; the nozzle pressure ratio ranged from 1.0 (jet off) to 9.0. The Reynolds number based on the wing mean aerodynamic chord varied from 3.0 x 10 to the 6th power to 4.8 x 10 to the 6th power, depending on Mach number. Aerodynamic characteristics were analyzed to determine the effects of thrust vectoring and the canard effects on the wing-afterbody-nozzle and the wing-afterbody portions of the model. Thrust vectoring had no effect on the angle of attack for the onset of flow separation on the wing but resulted in reduced drag at angle-of-attack values above that required for wing flow separation. The canard was found to have little effect on the thrust-induced lift resulting from vectoring, since canard effects occurred primarily on the wing.

Mason, M. L.↗
NASA NTRS1989

Euler code evaluation of a conical vehicle at supersonic speeds

A study has been conducted on a conical wing-body transatmospheric vehicle at Mach numbers from 1.5 to 4.5. The objective of the study was to evaluate the application of a Euler code to a wing-body configuration across the supersonic Mach number range. The baseline wing-body fuselage consisted of a circular 5-deg half-angle conical forebody, a cylindrical midbody, and a 9-deg truncated conical boattail. The wing was a 4-percent-thick diamond airfoil wing of aspect ratio 1. Results show that the Euler code accurately predicted the lift, drag, and pitching moment coefficients as a function of Mach number and angle of attack. The longitudinal stability characteristics were predicted as a function of Mach number. The code also predicted the changes in lift, drag, and pitching moment for forward and rearward shift of the wing from the nominal position.

Mcgrath, Brian E.↗
NASA NTRS1991

Definition of the unsteady vortex flow over a wing/body configuration

A problem of current interest in computational aerodynamics is the prediction of unsteady vortex flows over aircraft at high angles of attack. A six-month experimental effort was conducted at the John H. Harper Wind Tunnel to acquire qualitative and quantitative information on the unsteady vortex flow over a generic wing-body configuration at high angles of attack. A double-delta flat-plate wing with beveled edges was combined with a slender sharp-nosed body-of-revolution fuselage to form the generic configuration. This configuration produces a strong attached leading edge vortex on the wing, as well as sharply-peaked flow velocity spectra above the wing. While it thus produces flows with several well-defined features of current interest, the model was designed for efficiency of representation in computational codes. A moderate number of surface pressure ports and two unsteady pressure sensors were used to study the pressure distribution over the wing and body surface at high angles of attack; the unsteady pressure sensing did not succeed because of inadequate signal-to-noise ratio. A pulsed copper vapor laser sheet was used to visualize the vortex flow over the model, and vortex trajectories, burst locations, mutual induction of vortex systems from the forebody, strake, and wing, were quantified. Laser Doppler velocimetry was used to quantify all 3 components of the time-average velocity in 3 data planes perpendicular to the freestream direction. Statistics of the instantaneous velocity were used to study intermittency and fluctuation intensity. Hot-film anemometry was used to study the fluctuation energy content in the velocity field, and the spectra of these fluctuations. In addition, a successful attempt was made to measure velocity spectra, component by component, using laser velocimetry, and these were compared with spectra measured by hot-film anemometry at several locations.

Liou, S. G.↗
NASA NTRS1971

Hypersonic shock wave interaction and impingement

An experimental investigation was conducted on space shuttle type, body-wing configurations. The purpose of the investigation was to determine the effects of body and wing geometry on the hypersonic shock structure about these vehicles and on the resulting surface impingement of interior flow field shock and expansion waves. Schlieren photographs and thermographic phosphor paint data were obtained on three body cross sections with three wing planforms at 40, 50 and 60 degree angles of attack. Specific configuration data were obtained at 0 and 30 degree angles of attack to develop trends. These data were obtained at a nominal Mach number of 13.5 and a freestream unit Reynolds number of 0.7 million per foot. For comparison with these straight wing configurations, data were also obtained on a model of a point design, high cross-range, delta wing orbiter at 40, 50 and 60 degree angles of attack. As expected, the data on this delta wing orbiter indicated that the shock intersection/impingement phenomena associated with straight wing vehicles are considerably more complex than, and result in both windward and leeward surface heating regions not present on, the delta configuration.

Kessler, W. C.↗
NASA NTRS2004

Investigation of Injector Slot Geometry on Curved-Diffuser Aerodynamic Performance

The Compressor Branch vision is to be recognized as world-class leaders in research for fluid mechanics of compressors. Its mission is to conduct research and develop technology to advance the state of the art of compressors and transfer new technology to U.S. industries. Maintain partnerships with U.S. industries, universities, and other government organizations. Maintain a balance between customers focused and long range research. Flow control comprises enabling technologies to meet compression system performance requirements driven by emissions and fuel reduction goals (e.g., in UEET), missions (e.g., access-to-space), aerodynamically aggressive vehicle configurations (e.g., UAV and future blended wing body configurations with highly distorted inlets), and cost goals (e.g., in VAATE). The compression system requirements include increased efficiency, power-to-weight, and adaptability (i.e., robustness in terms of wide operability, distortion tolerance, and engine system health and reliability). The compressor flow control task comprises efforts to develop, demonstrate, and transfer adaptive flow control technology to industry to increase aerodynamic loading at current blade row loss levels, to enable adaptive1 y wide operability, and to develop plant models for adaptive compression systems. In this context, flow control is the controlled modification of a flow field by a deliberate means beyond the natural (uncontrolled) shaping of the solid surfaces that define the principal flow path. The objective of the compressor flow control task is to develop and apply techniques that control circulation, aerodynamic blockage, and entropy production in order to enhance the performance and operability of compression systems for advanced aero-propulsion applications. This summer I would be working with a curved-diffuser because it simulates what happens with flow in the stator blades in the compressor. With this experiment I will be doing some data analysis and parametric study of the injector slot geometries to get the best aerodynamic performance of it. This includes some data reduction, redesign and fast prototyping of the injector nozzle.

Silva, Odlanier↗
NASA NTRS1982

Calculation of three-dimensional, inviscid supersonic, steady flows

A numerical technique is described for the calculation of three dimensional, inviscid, supersonic, steady flows over wing-body configurations. A high degree of accuracy without increasing the number of computational nodes is obtained by means of a powerful conformal mapping technique. Results are presented for some simple body configurations and for a more complex arrow wing airframe. The numerical results show good agreement with experimental measurements.

Moretti, G.↗
NASA NTRS1992

A study of transonic aerodynamic analysis methods for use with a hypersonic aircraft synthesis code

A means of performing routine transonic lift, drag, and moment analyses on hypersonic all-body and wing-body configurations were studied. The analysis method is to be used in conjunction with the Hypersonic Vehicle Optimization Code (HAVOC). A review of existing techniques is presented, after which three methods, chosen to represent a spectrum of capabilities, are tested and the results are compared with experimental data. The three methods consist of a wave drag code, a full potential code, and a Navier-Stokes code. The wave drag code, representing the empirical approach, has very fast CPU times, but very limited and sporadic results. The full potential code provides results which compare favorably to the wind tunnel data, but with a dramatic increase in computational time. Even more extreme is the Navier-Stokes code, which provides the most favorable and complete results, but with a very large turnaround time. The full potential code, TRANAIR, is used for additional analyses, because of the superior results it can provide over empirical and semi-empirical methods, and because of its automated grid generation. TRANAIR analyses include an all body hypersonic cruise configuration and an oblique flying wing supersonic transport.

Sandlin, Doral R.↗
NASA NTRS1979

An experimental and theoretical investigation of the effect of nonmetric over-the-wing nacelles on wing-body aerodynamics

Drag reduction benefits due to blowing the jet exhausts over the wing for a transport-type wing-body configuration were investigated in the Langley 16-foot transonic tunnel. A combination of a wing-body model and a powered-nacelle test rig was tested at Mach numbers of 0.50 and 0.80 at angles of attack from -2 degrees to 4 degrees and jet total-pressure ratios from jet off to 3 or 4 (depending on Mach number) for a variety of nacelle locations relative to the wing. The experimental results were compared with the predictions obtained from several theoretical techniques. It was concluded that positioning of the nacelles (nonmetric) can have large effects on the wing-body drag. Some positions yielded higher drag than the baseline position, whereas others yielded lower drag than the baseline position. The theoretical method which utilized a quasi-vortex-lattice for the wing and wing-jet interaction in combination with a jet entrainment model gave generally reasonable predictions of the drag increments.

Reubush, D. E.↗
NASA NTRS1992

Numerical investigation of the effects of icing on fixed and rotary wing aircraft

A 2-D multi-element airfoil code was modified to study the effects of icing on the aerodynamic characteristics of high lift systems. In each zone of the flow field, the solver numerically integrates the 2-D compressible Navier-Stokes equations using a time marching scheme. The surface pressure distribution is generated over a GAW 130 airfoil/flap combination for a flap setting of 25 degrees, and an angle of attack equal to 5 degrees, at a freestream Mach number equal to 0.3. A series of calculations were performed to determine the effects of small scale ice build up on the high lift characteristics of this arifoil/flap combination. The appendix summarizes this progress. Joint studies on correlation of a 3-D iced wing code with experimental data reviewed new measured laser Doppler velocimeter data in the separated region behind the leading edge ice shape. A version of the iced wing analysis using the Roe scheme was developed to evaluate the poor correlation between the computed and measured velocities in the separated region. Work on the extension of the wing-alone analysis to wing body configuration began with modifications to the 3-D iced wing analyses to accept externally generated grids and multi-block grids.

Sankar, L. N.↗
NASA NTRS2016

Testing and Analysis of a Composite Non-Cylindrical Aircraft Fuselage Structure: Ultimate Design Loads - Part 1

The Environmentally Responsible Aviation Project aimed to develop aircraft technologies enabling significant fuel burn and community noise reductions. Small incremental changes to the conventional metallic alloy-based 'tube and wing' configuration were not sufficient to achieve the desired metrics. One airframe concept identified by the project as having the potential to dramatically improve aircraft performance was a composite-based hybrid wing body configuration. Such a concept, however, presented inherent challenges stemming from, among other factors, the necessity to transfer wing loads through the entire center fuselage section which accommodates a pressurized cabin confined by flat or nearly flat panels. This paper discusses finite element analysis and testing of a large-scale hybrid wing body center section structure developed and constructed to demonstrate that the Pultruded Rod Stitched Efficient Unitized Structure concept can meet these challenging demands of the next generation airframes. Part I of the paper considers the five most critical load conditions, which are internal pressure only and positive and negative g-loads with and without internal pressure. Analysis results are compared with measurements acquired during testing. Performance of the test article is found to be closely aligned with predictions and, consequently, able to support the hybrid wing body design loads in pristine and barely visible impact damage conditions.

Przekop, Adam↗
NASA NTRS2016

Testing and Analysis of a Composite Non-Cylindrical Aircraft Fuselage Structure : Severe Damage - Part II

The Environmentally Responsible Aviation Project aimed to develop aircraft technologies enabling significant fuel burn and community noise reductions. Small incremental changes to the conventional metallic alloy-based 'tube and wing' configuration were not sufficient to achieve the desired metrics. One airframe concept identified by the project as having the potential to dramatically improve aircraft performance was a composite-based hybrid wing body configuration. Such a concept, however, presented inherent challenges stemming from, among other factors, the necessity to transfer wing loads through the entire center fuselage section which accommodates a pressurized cabin confined by flat or nearly flat panels. This paper discusses a finite element analysis and the testing of a large-scale hybrid wing body center section structure developed and constructed to demonstrate that the Pultruded Rod Stitched Efficient Unitized Structure concept can meet these challenging demands of the next generation airframes. Part II of the paper considers the final test to failure of the test article in the presence of an intentionally inflicted severe discrete source damage under the wing up-bending loading condition. Finite element analysis results are compared with measurements acquired during the test and demonstrate that the hybrid wing body test article was able to redistribute and support the required design loads in a severely damaged condition.

Przekop, Adam↗
NASA NTRS2014

Nonlinear Finite Element Analysis of a Composite Non-Cylindrical Pressurized Aircraft Fuselage Structure

The Environmentally Responsible Aviation Project aims to develop aircraft technologies enabling significant fuel burn and community noise reductions. Small incremental changes to the conventional metallic alloy-based 'tube and wing' configuration are not sufficient to achieve the desired metrics. One of the airframe concepts that might dramatically improve aircraft performance is a composite-based hybrid wing body configuration. Such a concept, however, presents inherent challenges stemming from, among other factors, the necessity to transfer wing loads through the entire center fuselage section which accommodates a pressurized cabin confined by flat or nearly flat panels. This paper discusses a nonlinear finite element analysis of a large-scale test article being developed to demonstrate that the Pultruded Rod Stitched Efficient Unitized Structure concept can meet these challenging demands of the next generation airframes. There are specific reasons why geometrically nonlinear analysis may be warranted for the hybrid wing body flat panel structure. In general, for sufficiently high internal pressure and/or mechanical loading, energy related to the in-plane strain may become significant relative to the bending strain energy, particularly in thin-walled areas such as the minimum gage skin extensively used in the structure under analysis. To account for this effect, a geometrically nonlinear strain-displacement relationship is needed to properly couple large out-of-plane and in-plane deformations. Depending on the loading, this nonlinear coupling mechanism manifests itself in a distinct manner in compression- and tension-dominated sections of the structure. Under significant compression, nonlinear analysis is needed to accurately predict loss of stability and postbuckled deformation. Under significant tension, the nonlinear effects account for suppression of the out-of-plane deformation due to in-plane stretching. By comparing the present results with the previously published preliminary linear analysis, it is demonstrated in the present paper that neglecting nonlinear effects for the structure and loads of interest can lead to appreciable loss in analysis fidelity.

Przekop, Adam↗
NASA NTRS1978

Simulated propeller slipstream effects on a supercritical wing

To quantify the installed performance of high speed (M = 0.8) turboprop propulsion systems, an experimental program designed to assess the magnitude of the aerodynamic interference of a propeller slipstream on a supercritical wing has been conducted. The test was conducted in the NASA Ames 14-foot wind tunnel. An ejector-nacelle propeller slipstream simulator was used to produce a slipstream with characteristics typical of advanced propellers presently being investigated. A supercritical wing-body configuration was used to evaluate the interference effects. A traversing total pressure rake was used to make flow field measurements behind the wing and to calibrate the slipstream simulator. The force results indicated that the interference drag amounted to an increase of ten counts or about 3% of the wing-body drag for a two engine configuration at the nominal propeller operating conditions. However, at the higher swirl angles (11 deg vs. 7 deg nominally) the interference drag was favorable by about the same magnitude.

Welge, H. R.↗
NASA NTRS2022

Technology Maturation Report for Damage Arresting Composites under the Environmentally Responsible Aviation Project

The goal of the NASA Environmentally Responsible Aviation (ERA) Project was to develop technologies that will lead to commercial aircraft that will burn less fuel and produce fewer emissions than the 2010 state of the art. The purpose of this Technology Maturation Report (TMR) is to summarize both the development and lessons learned for the Damage Arresting Composites (DAC) Demonstration and to summarize how the test results were used to predict the impact the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) technology would have on future transport aircraft weights. The TMR includes the technical work plans for the DAC Demonstration for the six-year effort of the NASA ERA Project. System studies indicated that DAC would reduce structural weight by 20% for both hybrid wing body and tube and wing aircraft. A lighter vehicle requires less energy to fly so weight savings becomes reduced fuel burn. Additionally, the hybrid wing body configuration has improved lift-to-drag ratios compared to the tube and wing aircraft, further reducing fuel burn.

carbon-epoxy↗