Search NASA⌕ Search

SEARCH · Search NASA

Results for “acoustic absorption”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Low frequency sound absorption of orifice plates, perforated plates and nozzles

Analyses of impulse time history data from acoustic transmission tests for conical nozzles attached to a pipe show internal reflections from the solid contraction and open area tend to cancel. To gain understanding of the opposing reflections, tests were conducted by replacing the conical nozzles with orifice plates. The primary variable was the open to solid area ratio. Internal reflection coefficient data reveal that, at an area ratio of 10-12%, the low frequency internal reflection is reduced from unity to about 0.2. Based on comparisons of far-field and internal data, acoustic energy is not conserved. Results are presented for complex reflection coefficient and far-field noise for a series of orifice and perforated plate configurations.

Salikuddin, M.↗
NASA NTRS2012

Development and Validation of an Interactive Liner Design and Impedance Modeling Tool

The Interactive Liner Impedance Analysis and Design (ILIAD) tool is a LabVIEW-based software package used to design the composite surface impedance of a series of small-diameter quarter-wavelength resonators incorporating variable depth and sharp bends. Such structures are useful for packaging broadband acoustic liners into constrained spaces for turbofan engine noise control applications. ILIAD s graphical user interface allows the acoustic channel geometry to be drawn in the liner volume while the surface impedance and absorption coefficient calculations are updated in real-time. A one-dimensional transmission line model serves as the basis for the impedance calculation and can be applied to many liner configurations. Experimentally, tonal and broadband acoustic data were acquired in the NASA Langley Normal Incidence Tube over the frequency range of 500 to 3000 Hz at 120 and 140 dB SPL. Normalized impedance spectra were measured using the Two-Microphone Method for the various combinations of channel configurations. Comparisons between the computed and measured impedances show excellent agreement for broadband liners comprised of multiple, variable-depth channels. The software can be used to design arrays of resonators that can be packaged into complex geometries heretofore unsuitable for effective acoustic treatment.

Howerton, Brian M.↗
NASA NTRS1990

Experimental validation study of an analytical model of discrete frequency sound propagation in closed-test-section wind tunnels

The principal objective is to assess the adequacy of linear acoustic theory with an impedence wall boundary condition to model the detailed sound field of an acoustic source in a duct. Measurements and calculations are compared of a simple acoustic source in a rectangular concrete duct lined with foam on the walls and anechoic end terminations. Measurement of acoustic pressure for twelve wave numbers provides variation in frequency and absorption characteristics of the duct walls. Close to the source, where the interference of wall reflections is minimal, correlation is very good. Away from the source, correlation degrades, especially for the lower frequencies. Sensitivity studies show little effect on the predicted results for changes in impedance boundary condition values, source location, measurement location, temperature, and source model for variations spanning the expected measurement error.

Mosher, Marianne↗
NASA NTRS1990

Evaluation of discrete frequency sound in closed-test-section wind tunnels

The principal objective of this study is to assess the adequacy of linear acoustic theory with an impedance wall boundary condition for modeling the detailed sound field of an acoustic source in a duct. This study compares measurements and calculations of a simple acoustic source in a rectangular concrete duct lined with foam on the walls and anechoic end terminations. Measuring acoustic pressure for 12 wave numbers provides variation in frequency and absorption characteristics of the duct walls. The cases in this study contain low frequencies and low wall absorptions corresponding to measurements of low-frequency helicopter noise in a lined wind tunnel. This regime is particularly difficult to measure in wind tunnels due to high levels of the reverberant field relatively close to the source. Close to the source, where the interference of wall reflections is minimal, correlation is very good. Away from the source, correlation degrades, especially for the lower frequencies. Sensitivity studies show little effect on the predicted results for changes in impedance boundary condition values, source location, measurement location, temperature, and source model for variations spanning the expected measurement error.

Mosher, Marianne↗
NASA NTRS1979

Directivity of acoustic radiation from sources

The radiation properties of acoustic monopoles and dipoles are described. The directivity of radiation from these sources in a free field and in the presence of an absorptive surface is described. The kinematic effects on source radiation due to translation and rotation are discussed. Experimental measurements of sound from an acoustic monopole in motion and the characteristics of helicopter rotor and propeller noise are reviewed. An introduction is provided to several essential concepts required by noise control engineers making measurements of noise from moving sources in the proximity of the ground.

Lansing, D. L.↗
NASA NTRS1979

Directivity of acoustic radiation from sources

The radiation properties of acoustic monopoles and dipoles are described, as well as the directivity of radiation from these sources in a free field and in the presence of an absorptive surface. The kinematic effects on source radiation due to translation and rotation are discussed. Experimental measurements of sound from an acoustic monopole in motion and the characteristics of helicopter rotor and propeller noise are reviewed. Several essential concepts required by noise control engineers making measurements of noise from moving sources in the proximity of the ground are introduced.

Lansing, D. L.↗
NASA NTRSDate not supplied

Evaluation of Embedded Windshield Resonators to Reduce Cabin Noise of a UAM Concept Aircraft

High cabin noise levels in UAM vehicles could affect passenger comfort, and thus passenger acceptance of this class of aircraft. As windshields will likely comprise a large percentage of the surface area of a UAM aircraft fuselage, the objective of this work was to develop a noise reduction concept suitable for a windshield. The concept aims to increase interior absorption at targeted frequencies by including a honeycomb-like array of interior facing acoustic resonators within multiple transparent layers that make up the front and side windshields. The vehicle considered was based on the NASA RVLT Lift+Cruise UAM concept, which has 7.2 m2 of front- and side-facing windshields. Statistical Energy Analysis was used to evaluate the noise reduction attributed to the inclusion of various resonator configurations. The predicted noise reduction was dependent on the resonator geometry, the quantity of resonators included, and the assumed baseline interior cabin absorption. Results from a variety of resonator configurations are shown and discussed.

flight noise↗
NASA NTRS1990

Aeroacoustic effects of reduced aft tip speed at constant thrust for a model counterrotation turboprop at takeoff conditions

A model high-speed, advanced counterrotation propeller, F7/A7, was tested in the NASA Lewis Research Center's 9- by 15-foot anechoic wind tunnel at simulated takeoff and approach conditions of Mach 0.2. The propeller was operated in a baseline configuration with the forward and aft rotor blade setting angles (36.2deg and 35.4 deg) and forward and aft rotational speeds essentially equal. Two additional configurations were tested with the aft rotor at increased blade setting angles and the rotational speed reduced to achieve overall performance similar to that of the baseline configuration. The aft rotor blade angles were adjusted such that the thrust and power absorption for each rotor remained the same as for the baseline configuration. Acoustic data were taken with an axially translating microphone probe that was attached to the tunnel floor. Concurrent aerodynamic data were taken to define propeller operating conditions. The aft rotor fundamental tone was about 6 dB lower with the 36.2 deg and 38.4 deg blade setting angles, and about 9 dB lower with the 36.2 and 41.4 deg blade setting angles. Predicted noise reductions based on tip speed considerations were 5 and 9.5 dB, respectively, for the two altered blade setting angles.

Woodward, Richard P.↗
NASA NTRS1994

Microphone Corrections for Accurate In-Flow Acoustic Measurements at High Frequency

Acoustic analysis of aircraft components through small-scale experiments in wind tunnels requires in-flow acoustic measurements at high frequencies. This high frequency information is shifted to lower frequencies during the geometric scaling process. As a result, models of scale one tenth and smaller require frequency information of up to at least 100 kHz to resolve the midpoint of the full-scale equivalent audible range. Farfield acoustic measurements of frequencies higher than 100 kHz are prohibitively difficult to make due to the physical limitations of atmospheric propagation over large distances and the delicacy of the required instruments. Even measurements up to 100 kHz require special corrections and calibration procedures to maintain sufficient accuracy. In-flow microphone measurements at high frequencies require additional consideration due to the presence of the aerodynamic microphone forebody which protects the microphone diaphragm from flow impingement. The screen located at the forebody surface attenuates the high frequency acoustic waves and must be accounted for. The purpose of this paper is to present procedures for calibrating and correcting high frequency acoustic measurements to retain high accuracy. Specifically, this paper gives calibration procedures and examples of typical data for calibrating or correcting for five physical effects. These effects include the frequency response of the entire acoustic data acquisition system, intrusion of the microphone into the acoustic field, forebody screen attenuation, directionality of microphone forebody response and atmospheric absorption.

Allen, Christopher S.↗
NASA NTRS1999

Aerogel Composites: Strong and Waterproof

Aerogels are exotic materials having superior thermal and physical properties with great potential for both space and industrial uses. Although aerogels are excellent low-density insulators with unique acoustic and optical properties, their commercialization potential is currently limited by moisture absorption, fragility, and cost. This paper describes useful, easily scaled-up solutions to the first two of these three problems. The waterproofing and water-repellent method described here is a cheaper and simpler improvement over previous permanent methods.

White, Susan↗
NASA NTRS1973

Theory for radiatively driven harmonic acoustic waves in a confined gas.

A detailed theoretical study is made of radiatively driven acoustic waves inside a closed cylindrical tube. The formulation accounts for all the essential phenomena for a gas in vibrational equilibrium - namely, gas motion, longitudinal and radial viscous dissipation, longitudinal and radial heat conduction, and radiative transfer with spectral detail included. An approximate expression is derived for the pressure response. This solution is applicable to arbitrary spectral distribution of the radiative absorption coefficient, under conditions attainable in the laboratory. The solution includes both tuned and untuned acoustic conditions as well as the spectrophone limit - that is, the condition where the length of the tube is much smaller than the length of the acoustic wave. The influence of spectral detail on the pressure response is illustrated.

Chapman, G. T.↗
NASA NTRS2014

Evaluation of a Variable-Impedance Ceramic Matrix Composite Acoustic Liner

As a result of significant progress in the reduction of fan and jet noise, there is growing concern regarding core noise. One method for achieving core noise reduction is via the use of acoustic liners. However, these liners must be constructed with materials suitable for high temperature environments and should be designed for optimum absorption of the broadband core noise spectrum. This paper presents results of tests conducted in the NASA Langley Liner Technology Facility to evaluate a variable-impedance ceramic matrix composite acoustic liner that offers the potential to achieve each of these goals. One concern is the porosity of the ceramic matrix composite material, and whether this might affect the predictability of liners constructed with this material. Comparisons between two variable-depth liners, one constructed with ceramic matrix composite material and the other constructed via stereolithography, are used to demonstrate this material porosity is not a concern. Also, some interesting observations are noted regarding the orientation of variable-depth liners. Finally, two propagation codes are validated via comparisons of predicted and measured acoustic pressure profiles for a variable-depth liner.

Jones, M. G.↗
NASA NTRS1990

The spatial distribution of p-mode absorption in active regions

The interaction of solar p-mode waves and active regions has been the subject of recent observational and theoretical investigations. Observations show that up to one-half of the power of incident high-degree acoustic may be absorbed in and around sunspots. In this paper the horizontal spatial distribution of high-degree p-mode absorption in solar active regions is explored. An appropriate Fourier-Hankel transform can be used to detect the mean absorption of waves passing through any given point on the solar surface. By repeating the analysis at multiple positions a map of the absorption can be constructed. A technique for optimal computation of absorption maps is developed and applied to observations of several active regions and an area of quiet sun near disk center. By comparing the distribution of p-mode absorption with magnetograms and line-wing intensity images, it is directly observed that the absorption is not limited to the location of the visible sunspots but is also associated with magnetic fields in the surrounding plage. It is estimated that the absorption efficiency scales roughly with the magnetic flux density, although the absorption appears to saturate inside the strongest fields.

Braun, D. C.↗
NASA NTRS2002

Acoustic Quality of the 40- by 80- Foot Wind Tunnel Test Section After Installation of a Deep Acoustic Lining

A recessed, 42-inch deep acoustic lining has been designed and installed in the 40- by 80- Foot Wind Tunnel (40x80) test section to greatly improve the acoustic quality of the facility. This report describes the test section acoustic performance as determined by a detailed static calibration-all data were acquired without wind. Global measurements of sound decay from steady noise sources showed that the facility is suitable for acoustic studies of jet noise or similar randomly generated sound. The wall sound absorption, size of the facility, and averaging effects of wide band random noise all tend to minimize interference effects from wall reflections. The decay of white noise with distance was close to free field above 250 Hz. However, tonal sound data from propellers and fans, for example, will have an error band to be described that is caused by the sensitivity of tones to even weak interference. That error band could be minimized by use of directional instruments such as phased microphone arrays. Above 10 kHz, air absorption began to dominate the sound field in the large test section, reflections became weaker, and the test section tended toward an anechoic environment as frequency increased.

Soderman, Paul T.↗
NASA NTRS1973

Line profiles and turbulence generated by acoustic waves in the solar chromosphere. II - Contours of the Ca II and Mg II K lines

Making use of the time-averaged absorption profiles derived by Oster and Ulmschneider, non-LTE line formation in the context of a two-level atom is investigated for an isothermal atmosphere and for the Ca II and Mg II K lines in the solar chromosphere as represented by the Harvard-Smithsonian Reference Atmosphere. Source functions and emergent line profiles are computed for a variety of assumptions concerning the acoustically broadened profiles and the solar velocity fields.

Shine, R. A.↗
NASA NTRSDate not supplied

Preliminary Design of a Distributed Facesheet Acoustic Liner for Broadband Acoustic Attenuation

The purpose of this study is to investigate the acoustic performance of a liner with a distributed facesheet and a uniform depth core for broadband attenuation. The distributed facesheet is comprised of a cluster of three distinct cell resonators of varying hole diameter and porosity replicated over the active liner treatment area. A target frequency range of 1000 to 2000 Hz and an attenuation metric of 10 dB are chosen. An optimizer is used to determine the optimal facesheet designs for flow conditions of Mach 0.0 and Mach 0.3. The samples are tested in the Grazing Flow Impedance Tube at NASA Langley Research Center. The two liners are shown to achieve at least 10 dB attenuation over frequency ranges of 700 and 400 Hz, respectively, when tested at their respective designed flow speeds. This study demonstrate that a distributed facesheet with a uniform depth core can be successfully used to achieve broadband sound absorption.

acoustic liners↗