Simulating martensitic transformation in NiTi-Hf – effects of alloy composition and aging treatment
Not Available
Yu, Taiwu (ORCID:0000000347329156)↗
SEARCH · Search NASA
Results for “aging effect”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Insights into palladium poisoning of Cu/SSZ-13 selective catalytic reduction catalysts
Here, the impacts of Pd poisoning to the activity, selectivity, and hydrothermal stability of Cu/SSZ-13 selective catalytic reduction (SCR) catalysts are reported. Pd lowers DeNOx efficiency of Cu/SSZ-13 via two mechanisms: (1) displacing SCR active sites in the form of isolated Pd-ions, and (2) catalyzing non-selective NH 3 oxidation in the form of PdO. The first mechanism works by the diffusion of isolated Pd-ions into chabazite cages to displace ZCu II OH SCR active species, and it occurs on Cu/SSZ-13 catalysts with and without external surface CuO clusters in similar fashion. In contrast, the second mechanism works differently with and without external surface CuO clusters. For Cu/SSZ-13 catalyst without external CuO clusters (i.e., primarily isolated Cu-ions), PdO leads to significant decrease of DeNOx efficiency at reaction temperatures above ~400°C due to its non-selective NH 3 oxidation activity at high temperatures. However, this poisoning effect becomes much less impactful on Cu/SSZ-13 catalyst containing CuO clusters. This is due to the formation of CuO-PdO solid solution via interactions between CuO and PdO, which reduces non-selective NH 3 oxidation potential. Furthermore, this solid solution formation even mitigates adverse effects caused by hydrothermal aging. Hence, the poisoning effects of Pd are closely related to Cu speciation and spatial distribution of a Cu/SSZ-13 catalyst. Finally, this study suggests a strategy in eliminating Pd poisoning, that is, the introduction of an oxide phase that effectively traps PdO but does not adversely influence SCR.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
A regional comparison of sub-daily flow variability in regulated and unregulated rivers in the United States
Regulating rivers for hydropower or other purposes can dramatically alter river flow patterns, including creating substantial changes in flow over short, minutes-to-hours-long timespans known as sub-daily flow variability (SDFV). The impacts of flexible hydropower production on flow and aquatic organisms are increasingly documented in research. However, the degree to which flow alteration relates to different hydropower operational modes in distinct geographical regions and seasons is not well understood. This study offers a methodology for regional- and species-appropriate evaluations of potential impacts of flow on fish based on sub-daily flow characteristics of hydropower operational modes. We analyzed 15-min discharge data between 2018 and 2021 from 69 USGS stream gages to compare SDFV in hydropeaking, run-of-river, and unregulated systems in the US Southeast and Pacific Northwest. Regulated systems exhibited significant SDFV downstream from hydropower facilities relative to unregulated systems, but specific impacts differed between regions. Regulated systems in the Southeast were characterized by high flow coefficients of variation and ratios (hydropeaking only) and extended durations of daily upramping flow phases. Regulated systems in the Pacific Northwest were characterized by many short flow phases per day and large portions of the day spent upramping. Pacific Northwest unregulated systems displayed the strongest seasonal flow patterns while Southeastern hydropeaking systems displayed the greatest SDFV. Given that SDFV impacts multiple dimensions of fish ecology, region-specific sub-daily flow signatures have important implications for understanding and mitigating potential community-, species-, and age-specific effects on fish in different parts of the country.
Fish↗
Role of Coatings as Artificial Solid Electrolyte Interphases on Lithium Metal Self-Discharge
Artificial solid electrolyte interphases have provided a path to improved cycle life for high energy density, next-generation anodes like lithium metal. Although long cycle life is necessary for widespread implementation, understanding and mitigating the effects of aging and self-discharge are also required. In this report we investigate several coating materials and their role in calendar life aging of lithium. We find that the oxide coatings are electronically passivating whereas the LiF coating slows charge transfer kinetics. Furthermore, the Coulombic loss during self-discharge measurements improves with the oxide layers and worsens with the LiF layer. It is found that none of the coatings create a continuous conformal, electronically passivating layer on top of the deposited lithium nor are they likely to distribute evenly through a porous deposit, suggesting that none of the materials are acting as an artificial solid electrolyte interphase. Instead, they likely alter performance through modulating lithium nucleation and growth.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Demonstrating resonant ultrasound spectroscopy as a viable technique to characterize thermally conditioned high explosive materials
We present results of resonant ultrasound spectroscopy (RUS) measurements applied to granular high explosive materials at different bulk pressing densities and degree of thermal conditioning. The material chosen in this study is a ubiquitously used explosive material known as pentaerythritol tetranitrate (PETN), which is used commercially in civil and defense applications both as a binderized plastic bonded explosive material and an unbinderized neat material. However, changes in granular PETN bulk elastic properties due to thermal conditioning, which could have implications for better understanding environmental aging-related effects, have not been well studied even though it is believed that elasticity may play an important role in explosive material initiation mechanisms. Furthermore, monitoring elastic property changes in granular explosive pressings has not yet been demonstrated using RUS, which is an appealing non-destructive characterization tool that requires only dry point contact with the explosive material. To this end, we report the first study using RUS to quantify the elastic properties of binderized and neat PETN pressings as well as to quantify changes in elastic properties as a function of both thermal conditioning and bulk pressing density. Elastic stiffness coefficients, sometimes more commonly referred to as elastic constants, calculated from the RUS measurements on the different PETN-based materials show a significant increase for the post-conditioned samples compared to the pre-conditioned samples. This trend of increasing elastic properties with thermal conditioning was consistent for different density pressings, different thermal exposure conditions, and even different neat PETN pressings of differing average crystal sizes and/or specific surface areas.
36 MATERIALS SCIENCE↗
The Abrasion of Photovoltaic Glass: A Comparison of the Effects of Natural and Artificial Aging
Natural soiling and the subsequent requisite cleaning of photovoltaic (PV) modules result in abrasion damage to the cover glass. The durability of the front glass has important economic consequences, including determining the use of antireflective and/or antisoiling coatings as well as the method and frequency of operating maintenance (cleaning). The abrasion of coatings and glass has been explored in a field study, including the soiling-prone locations of Dubai (United Arab Emirates), Kuwait City (Kuwait), Mesa (Arizona), Mumbai (India), and Sacramento (California). Dry-brush-cleaned specimens will be compared to those subjected to artificial-brush testing. The characteristics of material integrity, surface energy, optical transmittance, surface roughness, and scratch size were examined using an optical microscope, contact goniometer (for water), spectrophotometer, interferometer, and atomic force microscope (AFM), respectively. The findings of this study will be used to provide feedback regarding the cleaning equipment, cleaning methods, and coatings used in the PV industry. The study here will also be used to aid in developing an abrasion standard for the PV industry.
14 SOLAR ENERGY↗
Performance of a CO 2 sorbent for indoor air cleaning applications: Effects of environmental conditions, sorbent aging, and adsorption of co-occurring formaldehyde
Indoor air cleaning systems that incorporate CO 2 sorbent materials enable HVAC load shifting and efficiency improvements. This study developed a bench-scale experimental system to evaluate the performance of a sorbent under controlled operation conditions. A thermostatic holder containing 3.15 g sorbent was connected to a manifold that delivered CO 2 -enriched air at a known temperature and relative humidity (RH). The air stream was also enriched with 0.8-2.1 ppm formaldehyde. The CO 2 concentration was monitored in real-time upstream and downstream of the sorbent, and integrated formaldehyde samples were collected at different times using DNPH-coated silica cartridges. Sorbent regeneration was carried out by circulating clean air in countercurrent. Almost 200 loading/regeneration cycles were performed in the span of 17 months, from which 104 were carried out at reference test conditions defined by loading with air at 25°C, 38% RH, and 1000 ppm CO 2 , and regenerating with air at 80°C, 3% RH and 400 ppm CO 2 . The working capacity decreased slightly from 43-44 mg CO 2 per g sorbent to 39-40 mg per g over the 17 months. The capacity increased with lower loading temperature (in the range 15-35°C) and higher regeneration temperature, between 40 and 80°C. The CO 2 capacity was not sensitive to the moisture content in the range 6-9 g/m 3 , and decreased slightly when dry air was used. Loading isothermal breakthrough curves were fitted to three simple adsorption models, verifying that pseudo-first-order kinetics appropriately describes the adsorption process. The model predicted that equilibrium capacities decreased with increasing temperature from 15 to 35°C, while adsorption rate constants slightly increased. The formaldehyde adsorption efficiency was 80%-99% in different cycles, corresponding to an average capacity of 86 ± 36 µg/g. Formaldehyde was not quantitatively released during regeneration, but its accumulation on the sorbent did not affect CO 2 adsorption.
32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
Achieving giant electrostrain of above 1% in (Bi,Na)TiO 3 -based lead-free piezoelectrics via introducing oxygen-defect composition
Piezoelectric ceramics have been extensively used in actuators, where the magnitude of electrostrain is key indicator for large-stroke actuation applications. Here, we propose an innovative strategy based on defect chemistry to form a defect-engineered morphotropic phase boundary and achieve a giant strain of 1.12% in lead-free Bi 0.5 Na 0.5 TiO 3 (BNT)–based ceramics. The incorporation of the hypothetical perovskite BaAlO 2.5 with nominal oxygen defect into BNT will form strongly polarized directional defect dipoles, leading to a strong pinning effect after aging. The large asymmetrical strain is mainly attributed to two factors: The defect dipoles along crystallographic [001] direction destroy the long-range ordering of the ferroelectric and activate a reversible phase transition while promoting polarization rotation when the dipoles are aligned along the applied electric field. Our results not only demonstrate the potential application of BNT-based materials in low-frequency, large-stroke actuators but also provide a general methodology to achieve large strain.
36 MATERIALS SCIENCE↗
Mass Spectrometer Transient Analysis
This software implements a complete preprocessing pipeline for transient mass spectrometry (MS) data collected during TAP (Temporal Analysis of Products) experiments. It is designed to extract chemically meaningful fluxes from overlapping ion signals by applying a calibrated defragmentation matrix and solving the resulting linear system using non-negative least squares (NNLS) regression. The core script, preprocess_mass_spec.py, performs the following operations: Gain correction: Applies amplifier gain scalars derived from inert-packed calibration pulses to normalize signal intensities across AMUs and acquisition settings. Background subtraction: Removes experiment baselines using user-defined time windows, ensuring compatibility with slow-diffusing species and preventing negative values that would interfere with NNLS. Options to subtract before and after defragmentation. Defragmentation: Constructs a fragmentation matrix A from zeroth moments of calibration pulses (equal molar gas:inert mixtures) and solves Ax=b at each time point, where b is the raw MS signal and x is the estimated species flux. The matrix is normalized to inert signals and accounts for instrument-specific fragmentation behavior. Pulse-mode handling: Supports both averaged and individual pulse modes, enabling statistical treatment of fluxes and calculation of standard deviations. Integration and output: Computes zeroth moments (integrated fluxes) and exports time-resolved and integrated data in CSV format, suitable for downstream kinetic modeling. The software is validated using both virtual TAP simulations (VTAP) and experimental data from propane dehydrogenation (PDH) on CrOx/Al2O3 catalysts. It preserves temporal resolution by applying NNLS point-by-point across the pulse duration (typically 6,000+ time slices per pulse), leveraging the linear superposition principle to reconstruct full flux profiles. The defragmented outputs are compatible with kinetic extraction methods such as the G and Y procedures, which are used to derive rate–concentration relationships from TAP data. The details of these validations are discussed in detail in the supporting manuscript and supporting information. Example data and output files are also included. The methodology is robust to experimental noise and drift, with calibration protocols that account for pulse size effects, MS aging, and inert gas normalization. The software is modular, reproducible, and tailored for high-throughput TAP-MS workflows in catalysis research.
Kristy, Stephen [Idaho National Laboratory (INL), ↗
Organic Iodide Sorption from Dilute Gas Streams
Reprocessing used nuclear fuel releases volatile radionuclides, including 129 iodine (I), into the off-gas of a processing plant. Volatile radioiodine could be present in several forms, depending on the chemistry of the process used and the off-gas stream. Inorganic I 2 is expected to be the predominant I species in the dissolver off-gas (DOG), with minor organic iodides present. The bulk of the I is expected to volatilize into the DOG in parts-per-million-level (ppm) concentrations. In contrast, in the vessel off-gas (VOG), most of the volatile I is expected to be found as organic iodides, such as CH 3 I, C 4 H 9 I, and C 12 H 25 I. These species are expected to be present in parts-per-billion-level (ppb) concentrations but require abatement, even at low expected concentrations, to meet regulatory emissions limits in the United States. Historically, studies of I abatement by Ag-functionalized sorbents have focused on inorganic I in the DOG, but in the last few years, more research attention has been given to organic iodides, especially longer chain species, such as C 4 H 9 I, and C 12 H 25 I. This report has three main goals: (1) to present new data generated at Oak Ridge National Laboratory (ORNL) in FY21 on the sorption behavior of organic iodides on AgZ, (2) to summarize and synthesize organic iodide data produced by ORNL and Idaho National Laboratory (INL) over the last 4 years to answer questions on organic iodides behavior outlined in the 2018 joint test plan (Jubin et al. 2018), and (3) to propose a VOG abatement system design that can provide the capture efficiencies required to meet I emission limits. The 2021 ORNL experimental campaign tested the effects of organic iodide speciation and concentration in the off-gas, superficial velocity of the off-gas, and effects of aging on AgZ sorbent capacity. These studies found that the sorption rate of organic iodides by AgZ depends on the hydrocarbon chain length and the concentration in the off-gas. Higher molecular weight organic iodides adsorb to AgZ more slowly than I. At a concentration of 50 ppm concentration in the off-gas, CH 3 I loads 8% slower, C 4 H 9 I loads 20% slower, and C 12 H 25 I loads 40% slower than I. The lowest concentration loading rates calculated were in 5 ppm organic iodide gas streams in which AgZ gained on average 0.14 mg I/g sorbent/hour in the bench scale test system. Thus, longer sorbent beds might be needed to accommodate slower loading rates onto AgZ in lower concentration gas streams. Although sorption rate varies as a function of hydrocarbon chain length, the saturation concentration of the sorbent for these I-bearing species does not vary. Aging AgZ in a humid air stream for 9 months drops the overall sorbent capacity by ~35% for CH 3 I, ~50% for C 4 H 9 I, and ~40% for C 12 H 25 I. This results in a saturation capacity between 35 and 70 mg I/g sorbent for the aged AgZ. In conjunction with recent data produced by INL, these data are used to estimate the mass transfer zone (MTZ) and decontamination factor (DF) for sorbent beds of AgZ. Sorption tests performed with iodide gas concentrations of about 1 ppm and higher at a superficial gas velocity of 10 m/min, indicate that MTZ depths for these conditions tend to range between about 8-20 cm. Tests performed at lower concentrations between 50-90 ppb and at gas superficial velocities of 1, 10, and 20 m/min indicate that the MTZ depth increases with increasing superficial gas velocity. The 20 m/min test indicates that the MTZ for those conditions was at least 22 cm, and doubling the superficial gas velocity from 10 to 20 m/min could roughly double or triple the MTZ depth. Doubling and tripling the bounding MTZ depth of 20 cm for the body of MTZ estimates made at with 10 m/min superficial velocity would extend the MTZ for a superficial velocity of 20 m/min to 40-60 cm. This bounding limit applies to all of the organic iodides that have been tested. These results also indicate that the sorption rate-limiting step is not sensitive to the superficial gas velocity; otherwise the MTZ depth would not have increased approximately in proportion to the increase in the gas superficial velocity. This further suggests that the rate limiting step is not associated with mass transfer of the sorbate to the sorbent surface, or mass transfer of the reaction byproducts from the sorbent surface, but is associated with sorption or chemical reactions on the sorbent surface or in sorbent pores. Deep bed testing at INL has established DFs of >2,000 for I, CH 3 I, and C 4 H 9 I under a range of conditions (Soelberg et al. 2021, Bruffey et al. 2019). DF does not seem to be affected by the concentration of the organic iodide in the gas stream over the range of 1 to 50 ppm. Thus, if the MTZ is accommodated in sorbent bed design for the DOG and VOG, then regulatory DFs will be met. To meet the third objective outlined in this report, these experimental data were used to update an engineering evaluation of the VOG first completed in 2016. The updated VOG design can be found in an accompanying document (Welty et al., 2021; INL- LTD-21-64587). This report finds that the VOG will decrease in both size and complexity, relative to previous designs, and will still meet regulatory requirements for all iodine forms.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
The Dual-Axis Radiographic Hydrodynamic Test Facility Capability eXpansion (DCX) Strategy
The Dual-Axis Radiographic Hydrodynamic Test (DARHT) facility is a vital and important part of the Nation’s nuclear security enterprise. The Department of Energy/National Nuclear Security Administration (DOE/ NNSA) Stockpile Stewardship Management Plan (SSMP) identifies DARHT as a weapons mission critical facility along with the need to modernize DARHT to support weapons modernization efforts. With more than two decades of operations, DARHT has a storied history. Conceived in the 1970s, constructed in the 1990s, and operational since 2000, DARHT has advanced from open-air hydrodynamic experiments (hydros) to foam-confined hydros, to vessel-confined hydros, and in 2022, the 75 th hydro was successfully completed. Radiography has advanced from a single-axis, single-pulse system to a dual-axis, multi-pulse capability to variable fields of view (VFV) on both accelerators. The culmination of these experiences, accomplishments, and advancements has brought us to a very important question: What do the next two decades at DARHT look like? The world is not the same place it was in the 1990s when construction at DARHT was in progress. Evolving threats, an expanding mission, and technology changes necessitate adaptation. The 2018 Nuclear Posture Review (NPR) states that the nuclear weapons infrastructure has suffered the effects of age and underfunding with no margin for further delay in recapitalizing the physical infrastructure. To adapt, the aging facility, accelerators, vessels, and detector systems require improvements to ensure DARHT remains the Nation’s hydrodynamic data foundation for stockpile certification, safety, surety, and global security threats.
98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
2025 Review and Revision of Federal Guidance Report 15
Federal Guidance Report No. 15 (FGR 15), External Exposure to Radionuclides in Air, Water and Soil, published in 2019 and referred to below as FGR 2019, provides age-specific effective dose rate coefficients for reference persons externally exposed to each of 1252 radionuclides homogenously distributed in environmental media. Soon after completion of FGR 2019, the International Commission on Radiological Protection (ICRP) published a similar report (ICRP Publication 144, 2020) addressing the same radionuclides and many of the external exposure scenarios addressed in FGR 2019. In 2023 Argonne National Laboratory (ANL) published a review of dose coefficients in FGR 2019, concluding that “The external effective dose from beta radiation is not appropriately accounted for in FGR 15 for both low- and high-energy beta emitters in air, in soil, and on soil surfaces.” That conclusion was based largely on comparisons of dose coefficients in FGR 2019 with values in ICRP Publication 144 but also on consideration of some unexpected patterns of equivalent dose rate coefficients across tissues and of effective dose rate coefficients across different soil depths, for a selected set of low-energy beta emitters. In response to the ANL report, the Center for Radiation Protection Knowledge (CRPK) at Oak Ridge National Laboratory (ORNL) performed an extensive reexamination of the methods and published values of FGR 2019. CRPK found that coding errors had resulted in inaccurate estimates, primarily overestimates, in many of the dose coefficients tabulated in FGR 2019 but that many of the differences between results in FGR 2019 and ICRP Publication 144 could be traced to differences in methodology. CRPK has corrected all errors in FGR 2019 associated with the coding errors and has taken the opportunity to improve a major portion of the remaining dose coefficients in FGR 2019, primarily through additional Monte Carlo calculations resulting in improved statistics for tissue equivalent dose rate coefficients for exposure to monoenergetic sources. This has eliminated the need for extrapolation of results from high and medium energies to low energies, as was done in FGR 2019. In addition, inconsistencies in the methodology identified in the review, such as computational representation of the adult female, were eliminated. The revised effective dose rate coefficients are consistent with values in ICRP Publication 144 except for differences in values clearly arising from differences in methodology; and differences in values for a relatively small set of very low-energy radionuclides with highly uncertain dose coefficients regardless of methodology.
54 ENVIRONMENTAL SCIENCES↗
White Paper on Case Study of Safe Installation of Second-Life Energy Storage System
This technical report provides for a case study for the safe installation of a second-life, or repurposed, battery, that has been reconfigured for use as a stationary energy storage systems (ESS). Driven by legislative requirements such as California Senate Bill 615 and projections that retired EV batteries could meet a substantial portion of U.S. grid ESS needs beginning in 2035, the repurposing of EV batteries is anticipated to grow significantly. However, safety concerns arise from the effects of aging, unknown prior usage history, and changes in thermal runaway behavior, which may increase failure risks compared to new batteries. NFPA 855, the predominant U.S. standard for ESS installation, mandates that second-life batteries meet all requirements for new batteries, with repurposers complying with UL 1974 in addition to obtaining UL 9540 and UL 1973 listings. These are certifications that few repurposers have achieved and represent a regulatory barrier to entry for the market as a whole.
47 OTHER INSTRUMENTATION↗
Effect of Physical and Chemical Aging on the Yield Stress of the filled Epoxy System 828DEAGMB.
Abstract not provided.
Kropka, Jamie Michael↗
Effects of Surface Roughness and Aging on the Electrical Contact Resistance and Residual Stress in Gold-Nickel-Copper Connector Materials.
Abstract not provided.
Butler, Nan Ellen↗
Hydrolytic Aging in Rubber-Like Materials: A Micro-Mechanical Approach to Modeling
Abstract The effect of hydrolytic aging on mechanical responses of Rubber likes materials, in particular, Mullins effect and the permanent set has been modeled. Hydrolytic aging is considered as the result of the competition between two phenomena (1) chain scission and (2) cross-link scission/reformation. Both phenomena were modeled and thus, the strain energy of the polymer matrix is written with respect to three independent mechanisms; i) the shrinking original matrix which has not been attacked by water, ii) conversion of the first network to a new network due to the reduction of the crosslinks, and iii) energy loss from network degradation due to water attacks to ester groups. The model is validated with respect to a set of experimental data. Besides accuracy, the simplicity and few numbers of fitting parameters make the model a good choice for further implementations.
Bahrololoumi, Amir↗
A Physics-Based Data-Driven Approach for Modeling of Environmental Degradation in Elastomers
Abstract Elastomers are now commonly used in a number of industries, including aerospace, structure, transportation, shipbuilding, and automotive, due to their excellent workability, formability, and flexibility. During their activity, elastomers are subjected to harsh environmental conditions, which decreases their resilience. False predictions made early in their lives can have major financial and environmental implications. Elastomers’ performance and properties, such as strength, durability, and density, are influenced by chemical changes in these materials, known as degradation, which occurs over time. This process can alter the morphology of a polymer matrix as well as cause chain scission and cross-linking, resulting in different behaviors than that of the unaged material. To demonstrate the effect of thermaloxidative aging on the mechanical behavior of elastomers, several experimental and theoretical models have been proposed. In view of the large volume of experimental data available on micro-structural evolution in the course of aging, we propose a physics-based data-driven approach to overcome the shortcomings of both phenomenological and micro-mechanical models. This work presents a novel thermodynamically consistent, multiagent machine-learned model for predicting the constitutive behavior of cross-linked elastomers during environmental aging, such as thermo-oxidative and hydrolytic aging for various states of deformation. Single mechanism degradation changes the polymer matrix over time where it is causing chain scission, reduction of cross-links, and morphology change. To capture the idealized Mullins effect and permanent set due to the effect of single aging mechanisms on nonlinear mechanical responses of elastomers, we propose a data-driven model for simulating inelastic elements in a polymer matrix. By using a sequential order reduction, we were able to reduce the 3D stress-strain tensor mapping problem to a small number of super-constrained 1D mapping problems. To systematically classify such mapping problems into a few categories, an assembly of multiple replicated conditional neural network learning agents (L-agents) is used based on our recent work. Each category is represented by a different type of agent. The effect of deformation history, aging time, and aging temperature is captured by this model. The model is validated using a broad collection of data, ranging from our experimental results to data from the literature. In addition, thermodynamic consistency and frame independence are investigated. The most significant achievements of this model are its precision, simplicity, and prediction of inelasticity under various states of deformation. The model’s accuracy and simplicity make it a good option for commercial and industrial applications. Conveniently, due to the model modular nature, it can be expanded in the future to include viscoelasticity and non-isotropic formation for better precision.
Ghaderi, Aref↗
Relationship between microporous structure and light gas transport through glassy polymeric membranes revealed by molecular simulations
Microporous glassy polymers are attractive materials for gas separation membranes, due to their high permeability and tailorable selectivity, provided physical aging can be delayed. The archetypal microporous glassy polymer, PTMSP, can be blended with a hyper-crosslinked isatin–triptycene porous polymer network (PPN) to delay physical aging. However, while PPN is effective at reducing physical aging, it also affects the permeability of light gases through PTMSP. Molecular dynamics simulations were used here to shed fundamental light on the mechanisms responsible for these effects. Atomistic models are developed that satisfactorily reproduce experimental observations such as matrix density and cavity size distributions for neat PTMSP as well as for PTMSP–PPN blends. Analysis of the simulation results suggests that physical aging is delayed because the PPN inclusions slow down PTMSP relaxation while reducing the connectivity between free volume pockets. To understand how PPN inclusions affect light gas permeability, the atomistic models developed are used to probe CO 2 and CH 4 diffusion and sorption. These simulations are conducted for PTMSP matrices exhibiting varying density, towards reproducing experimental permeability data. Interrogating the simulation trajectories, it is discovered that while CH 4 travels preferentially through the free volume cavities, CO 2 preferentially interacts with the available surfaces, especially in the presence of PPN. These differences help interpret experimental observations. The transport of C 2 H 6 and H 2 S through PTMSP matrices was also investigated. These gases, and in particular H 2 S, were found to absorb within PTMSP, yielding very low diffusion coefficients. The ability to predict differences in diffusion pathways for various natural gas components unveils the possibility of engineering membranes to control permeability and selectivity towards large-scale applications.
Bao Le, Tran Thi [Univ. of Oklahoma, Norman, OK (U↗