Controls of nature: Secondary, tertiary, and quaternary structure of the enamel protein amelogenin in solution and on hydroxyapatite
Not Available
Shaw, Wendy J. (ORCID:0000000246967415)↗
SEARCH · Search NASA
Results for “atomic forces”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Ferroelectrics everywhere: Ferroelectricity in magnesium substituted zinc oxide thin films
We demonstrate ferroelectricity in Mg-substituted ZnO thin films with the wurtzite structure. Zn 1–x Mg x O films are grown by dual-cathode reactive magnetron sputtering on (111)-Pt // (0001)-Al 2 O 3 substrates at temperatures ranging from 26 to 200 °C for compositions spanning from x = 0 to x = 0.37. X-ray diffraction indicates a decrease in the c-lattice parameter and an increase in the a-lattice parameter with increasing Mg content, resulting in a nearly constant c/a axial ratio of 1.595 over this composition range. Transmission electron microscopy studies show abrupt interfaces between Zn 1–x Mg x O films and the Pt electrode. When prepared at pO 2 = 0.025, film surfaces are populated by abnormally oriented grains as measured by atomic force microscopy for Mg concentrations >29%. Raising pO 2 to 0.25 eliminates the misoriented grains. Optical measurements show increasing bandgap values with increasing Mg content. When prepared on a 200 °C substrate, films display ferroelectric switching with remanent polarizations exceeding 100 μC cm –2 and coercive fields below 3 MVcm –1 when the Mg content is between ~30% and ~7%. Substrate temperature can be lowered to ambient conditions, and when doing so, capacitor stacks show only minor sacrifices to crystal orientation and nearly identical remanent polarization values; however, coercive fields drop below 2 MV/cm. Using ambient temperature deposition, we demonstrate ferroelectric capacitor stacks integrated directly with polymer substrate surfaces.
36 MATERIALS SCIENCE↗
Structural and optical properties of cubic GaN on U-grooved Si (100)
Cubic GaN epitaxy on large-area U-grooved silicon (100) dies is demonstrated by metalorganic chemical vapor deposition, and its structural and optical properties are reported. Scanning electron, atomic force, and transmission electron microscopy studies reveal that cubic GaN shows no discernible threading dislocations and a low stacking fault density of 3.27 ± 0.18 × 10 4 cm –1 . Temperature-dependent photoluminescence studies reveal as-grown cubic GaN band edge emission internal quantum efficiency as 25.6% ± 0.9%. Selective etching of the low-temperature AlN buffer layer, SiO 2 sidewalls, and hexagonal-phase GaN is demonstrated, which increases the cubic GaN band edge emission internal quantum efficiency to 31.6% ± 0.8%. This increase is attributed to the decrease in the radiative recombination lifetime via the removal of defective hexagonal-phase GaN. Altogether, cubic GaN on U-grooved silicon with high structural and optical quality is reported, promising its suitability for next-generation devices.
36 MATERIALS SCIENCE↗
Effects of electron beam irradiation on CrMnV and CrMnTiV high entropy alloys: Nano-mechanical, structural, and thermodynamic perspectives
Beam exit windows are crucial components of any particle accelerator as they provide an interface between the beamline vacuum and target material at atmospheric media. For high beam power machines, special materials and designs are required to withstand high radiation and mechanical loads, while minimizing energy loss during transition and maximizing window lifetime. This research investigates the impact of electron beam exposure to bulk CrMnV and CrMnTiV high entropy alloys (HEAs) with the primary goal of identifying suitable candidate materials for the design of robust and durable exit window settings. The selection criteria include intrinsic characteristics, power dissipation, and mechanical responses. According to the thermodynamic calculations, both equiatomic CrMnV and the addition of 7% of Ti with equiatomic CrMnV yield solid-solutions phases. The structural and mechanical properties of CrMnV and CrMnTiV samples were tested using field emission scanning electron microscopy, atomic force microscopy, scanning electron microcopy with energy dispersive x-ray spectroscopy, x-ray diffraction, and nanoindentation before and after exposure to a dose of ~66 kGy from a 10 MeV e-beam accelerator. Despite exhibiting beam transmission characteristics comparable to Cr and V, the indentation hardness of HEAs exceeded that of the Cr and V samples by five to six times. The examination of the CrMnTiV irradiated samples revealed organized deformation patterns depicting new features, which we suspect twinning and twin boundaries due to the addition of Ti to CrMnV. Ti, a hexagonal-close-packed crystal structure, is commonly known for deformation twinning behavior.
36 MATERIALS SCIENCE↗
Scattering-type scanning near-field optical microscopy with Akiyama piezo-probes
Recent developments of the scattering-type scanning near-field optical microscope at cryogenic temperatures (cryogenic s-SNOM or cryo-SNOM) have led to many breakthroughs in the studies of low energy excitations in quantum materials. However, the simultaneous demands on vibration isolation, low base temperature, precise nano-positioning, and optical access make the construction of a cryo-SNOM a daunting task. Adding to the overhead space required for a cryo-SNOM is the atomic force microscopy control, which predominantly utilizes a laser-based detection scheme for determining the cantilever tapping motion. In this work, we provide an alternative and straightforward route to performing s-SNOM using metal-coated Akiyama probes, where the cantilever tapping motion is detected through a piezoelectric signal. We show that the Akiyama-based cryo-SNOM attains high spatial resolution, good near-field contrast, and is able to perform imaging with a significantly more compact system compared to other cryo-SNOM implementations. Our results firmly establish the potential of s-SNOM based on self-sensing piezo-probes, which can easily accommodate far-infrared wavelengths and high magnetic fields in the future.
71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
Low temperature absolute internal quantum efficiency of InGaN-based light-emitting diodes
A method to reveal low temperature absolute internal quantum efficiency of an InGaN-based light-emitting diode (LED) is reported. Structural (via scanning electron and atomic force microscopies, x-ray diffraction, and Raman spectroscopy) and optical (via temperature- and power-dependent photoluminescence) properties of InGaN-based blue LEDs are coupled with a channel-based recombination model, which reveals the low temperature absolute internal quantum efficiency of the LED on traditional sapphire and emerging Si (111) substrates as 27.5% and 71.1%, respectively. High low-temperature absolute internal quantum efficiency of the former is attributed to its lower defect density and less strain. Furthermore, our results show assuming perfect (i.e., 100%) internal quantum efficiency in an InGaN-based LED at low temperatures could be misleading, and using negative thermal quenching properties of defect luminesce bands with a channel-based recombination model can be a method to quantify LED's less than ideal low temperature internal quantum efficiencies.
36 MATERIALS SCIENCE↗
Nanofabrication of silicon surfaces for reduced virus adhesion
Nanofabrication is a remarkably effective technique to create desirable nanoscale patterns. Here, the effect of surface nanofabrication on altering virus adhesion to the substrates was examined. Arrays of nanoholes, 50 nm in diameter, 22 nm deep, and 100 nm in pitch distance, were created on silicon (Si) wafers by electron-beam lithography and reactive ion etching. MS2 coliphage, which is 26 ± 2 nm in diameter and is frequently used as a surrogate for human viruses, was applied to investigate the interaction between the virions and smooth or nanostructured Si surfaces. Scanning electron microscopy and atomic force microscopy along with surface wettability analyses revealed that the nanofabrication had the effect of reducing not only the number of viruses attached but also the strength of virus adhesion. These effects were ascribed to the presence of nanoholes, which were inaccessible to the virions due to the unique surface topographical parameters and the surface chemistry, resulting in the decrease of the overall solid contact area for MS2 attachment. The periodic spacing of the nanoholes also limited the unit landing area for MS2 particles, restricting the formation of MS2 aggregates and leading to the reduced amount of MS2 attachment. We anticipate that smart design of a surface’s chemical composition and nanostructure will offer a feasible solution to improve mitigations for controlling viral adhesion and transmission to and from food contact surfaces.
36 MATERIALS SCIENCE↗
Dynamic Structural Change of Plant Epidermal Cell Walls under Strain
Abstract The molecular foundations of epidermal cell wall mechanics are critical for understanding structure–function relationships of primary cell walls in plants and facilitating the design of bioinspired materials. To uncover the molecular mechanisms regulating the high extensibility and strength of the cell wall, the onion epidermal wall is stretched uniaxially to various strains and cell wall structures from mesoscale to atomic scale are characterized. Upon longitudinal stretching to high strain, epidermal walls contract in the transverse direction, resulting in a reduced area. Atomic force microscopy shows that cellulose microfibrils exhibit orientation‐dependent rearrangements at high strains: longitudinal microfibrils are straightened out and become highly ordered, while transverse microfibrils curve and kink. Small‐angle X‐ray scattering detects a 7.4 nm spacing aligned along the stretch direction at high strain, which is attributed to distances between individual cellulose microfibrils. Furthermore, wide‐angle X‐ray scattering reveals a widening of (004) lattice spacing and contraction of (200) lattice spacing in longitudinally aligned cellulose microfibrils at high strain, which implies longitudinal stretching of the cellulose crystal. These findings provide molecular insights into the ability of the wall to bear additional load after yielding: the aggregation of longitudinal microfibrils impedes sliding and enables further stretching of the cellulose to bear increased loads.
59 BASIC BIOLOGICAL SCIENCES↗
Surviving nanoscale interfacial stability in extreme thermal expansion contrast Zn(CN) 2 -epoxy resin matrix composites
Here, we report the remarkable stability at the nanoscale matrix-filler interface in a series of overall low coefficient of thermal expansion (CTE) zinc cyanide (ZC)/epoxy resin composites. These interfaces demonstrate the stability of highly contrasting materials. These composites are designed to optimize the properties of both materials: epoxy resins are valued for their high strength, superb chemical resistance, low dielectric properties, and adhesive abilities. ZC, a model flexible framework, exhibits negative thermal expansion (NTE) behavior and compensates for the epoxy resin’s detrimentally large thermal expansion values. Filled resins minimize the native 65 ppm/°C CTE values to 19 ppm/° C over a wide temperature range while maintaining linearity, yielding composites compatible with typical metal and ceramic substrates’—commonly bonded to the resin— 0–20 ppm/° C CTE values. Additionally, with significant intrinsic differences in the materials, we use wide-angle X-ray diffraction and atomic force microscopy to elucidate thermal movement. The ZC/epoxy interface is surprisingly resilient over 1,000 cycles between -55° C and 75° C, extremes typical to aerospace applications. Further, we show that the resin viscosity remains less than 21 Pa*s at up to 30 vol% ZC, an important consideration for workability. We also discuss settling distribution, glass transition temperature, flexural strength, and longevity. All results point favorably towards practical implementation in low thermal expansion application needs: filling the gap in component design.
42 ENGINEERING↗
Synchronous RNA conformational changes trigger ordered phase transitions in crystals
Time-resolved studies of biomacromolecular crystals have been limited to systems involving only minute conformational changes within the same lattice. Ligand-induced changes greater than several angstroms, however, are likely to result in solid-solid phase transitions, which require a detailed understanding of the mechanistic interplay between conformational and lattice transitions. Here we report the synchronous behavior of the adenine riboswitch aptamer RNA in crystal during ligand-triggered isothermal phase transitions. Direct visualization using polarized video microscopy and atomic force microscopy shows that the RNA molecules undergo cooperative rearrangements that maintain lattice order, whose cell parameters change distinctly as a function of time. The bulk lattice order throughout the transition is further supported by time-resolved diffraction data from crystals using an X-ray free electron laser. The synchronous molecular rearrangements in crystal provide the physical basis for studying large conformational changes using time-resolved crystallography and micro/nanocrystals.
59 BASIC BIOLOGICAL SCIENCES↗
Properties and device performance of BN thin films grown on GaN by pulsed laser deposition
Wide and ultrawide-bandgap semiconductors lie at the heart of next-generation high-power, high-frequency electronics. Here, in this paper, we report the growth of ultrawide-bandgap boron nitride (BN) thin films on wide-bandgap gallium nitride (GaN) by pulsed laser deposition. Comprehensive spectroscopic (core level and valence band x-ray photoelectron spectroscopy, Fourier-transform infrared spectroscopy, and Raman) and microscopic (atomic force microscopy and scanning transmission electron microscopy) characterizations confirm the growth of BN thin films on GaN. Optically, we observed that the BN/GaN heterostructure is second-harmonic generation active. Moreover, we fabricated the BN/GaN heterostructure-based Schottky diode that demonstrates rectifying characteristics, lower turn-on voltage, and an improved breakdown capability (~234 V) as compared to GaN (~168 V), owing to the higher breakdown electrical field of BN. Our approach is an early step toward bridging the gap between wide and ultrawide-bandgap materials for potential optoelectronics as well as next-generation high-power electronics.
42 ENGINEERING↗
Accelerating Structure–Property Relationship Discovery with Multimodal Machine Learning and Self-Driving Microscopy
Microscopy combined with local spectroscopy is widely used to correlate nanoscale structure with functional properties in materials, but conventional measurements rely heavily on human-selected sampling locations and predefined targets, limiting data set diversity and the potential for discovery. Here, we present a framework that integrates autonomous microscopy with dual-novelty deep kernel learning (DN-DKL) for adaptive data acquisition and a dual variational autoencoder (VAE) for representation learning. DN-DKL actively guides the microscopy toward structurally and spectroscopically novel regions, enabling efficient collection of large spectral data sets. Dual-VAE embeds local structures and spectroscopic responses into a shared latent manifold that serves as a structure–property relationship map. We applied this framework for the investigation of halide perovskite films by using conductive atomic force microscopy. The results reveal distinct hysteresis behaviors that are linked to specific nanoscale structural motifs, including grain boundary junction points that show hysteresis under different bias conditions and asymmetric grain boundaries that suppress the charge transport. This framework establishes a general strategy that leverages the complementary strengths of self-driving microscopy, machine learning, and human expertise to accelerate scientific discovery in functional materials.
atomic force microscopy↗
Structural Mimicry Drives HIV-1 Rev-Mediated HERV-K Expression
Explore the source record for details and available documents.
O'Carroll, Ina P.↗
Direct Multimodal Nanoscale Visualization of Early Phosphorus-Based Antiwear Tribofilm Formation
Understanding the mechanism of antiwear (AW) tribofilm formation and how to tune surface chemistry to control functionality is essential for the development of the next generation of oil lubricants. In particular, understanding and optimizing early AW tribofilm formation can increase the energy efficiency of mechanical systems. However, the mechanism for how these films form is not well understood. The majority of prior work has focused on analyzing only end-of-test surfaces long after the film has formed. In this work, we develop an in situ multimodal chemical imaging methodology to directly visualize the early formation of AW films on steel surfaces. We investigate an oil formulation containing a phosphorus-based additive commonly used to protect surfaces from wear and fatigue processes in machine elements, such as gears, bearings, and sliding contacts. Using nanoscale multimodal chemical imaging on combined platforms of atomic force microscopy (AFM) coupled directly with in situ nano-infrared (nano-IR) spectroscopy, and further combined ex situ with time-of-flight secondary ion mass spectrometry (ToF-SIMS), we demonstrate a direct correlation between changes in friction and local surface chemistry. In these experiments, the AFM probe acts as a single asperity contact to generate the tribofilm as well as a tool to analyze it in situ as it is forming. To verify our in situ measurements, we compare these results to the ex situ ToF-SIMS of macroscale block-on-ring tribometer-formed samples. We report the understanding gained here on how AW films form and how film properties can be modified by tuning the chemistry of the additives will facilitate developing transmission fluids to meet increasing demands for vehicle performance and efficiency.
36 MATERIALS SCIENCE↗
Multiscale Mechanical Characterization of Mineral-Reinforced Wood Cell Walls
Studying the multiscale mechanics of bio-based composites offers unique perspectives on underlying structure–property relations. Cellular materials, such as wood, are highly organized, hierarchical assemblies of load-bearing structural elements that respond to mechanical stimuli at the microscopic, mesoscopic and macroscopic scale. In this study, we modified oak wood with nanocrystalline ferrihydrite, a widespread ferric oxyhydroxide mineral, and characterized the resulting mechanical properties of the composite at various levels of organization. Ferrihydrite nanoparticles were deposited inside the wood cell wall by an in situ chemical reaction, resulting in increased stiffness and hardness of the functionalized secondary cell wall, as evidenced by region-specific nanoindentation tests under an electron microscope. Chemically modified and pristine wood samples were characterized by using atomic force microscopy in the bimodal frequency modulation mode, which produced topographical images from the cellular ultrastructure with high lateral resolution and localized nanomechanical information across distinct cell wall layers. In conclusion, despite mineral reinforcement at the cell wall level, the macroscopic fracture behavior examined through three-point flexural testing remained unchanged upon modification, as cell–cell adhesion could be impaired by harsh chemical conditions.
Cells↗
AFM Slip Length Measurements for Water at Selected Phyllosilicate Surfaces
Most reported slip length measurements have been made at the surfaces of synthetic materials and modified synthetic materials. In contrast, few slip length measurements at the surface of unmodified natural mineral surfaces have been reported. In this regard, flow at the silica face surfaces of the phyllosilicate minerals, talc and mica, was considered. A slip boundary condition was expected at the nonpolar hydrophobic silica surface of talc leading to enhanced flow, and a no-slip boundary condition was expected at the hydrophilic silica surface of mica. Atomic force microscopy (AFM) slip length measurements were made at the talc and mica surfaces. The slip length results for the hydrophobic silica surface of talc were contrasted to the results for the hydrophilic silica surface of mica (no-slip flow). The results are discussed based on molecular dynamics simulations (MDS), as reported in the literature, and AFM images of surface nanobubbles. For nonpolar hydrophobic surfaces (such as talc), it is doubtful that the MDS interfacial water structure and the water exclusion zone (3.2 Å) account for the AFM slip flow with slip lengths as great as 95 nm. Rather, a better explanation for the AFM slip flow condition is based on reduced interfacial viscosity due to the presence of dissolved gas and the accommodation of pancake nanobubbles at the talc surface having a height dimension of magnitude similar to the slip length.
42 ENGINEERING↗
Nanometer Scale Imaging to Develop Quantitative Descriptors of Bipolar Membrane Junction Structure
Swings in pH can be achieved by electrically polarizing a bipolar membrane (BPM) to drive water dissociation at the BPM junction for electrochemical conversion and separation processes. BPM junction design is critical to tailor performance for specific applications; however, characterization techniques capable of resolving the nanometer scale physical structure of the junction are limited. We present sample preparation, imaging, and analysis workflows that are adaptable to a variety of BPM junction architectures. Atomic force microscopy produces BPM junction images with nanometer scale lateral resolution for samples with and without a graphene oxide water dissociation catalyst in the junction. Subsequent image segmentation and analysis quantify line edge roughness and catalyst layer thickness as descriptors of junction structure. Comparison of pre- and post-electrodialysis junctions suggests electric field-induced alignment of catalyst particles during electrodialysis. This characterization workflow can inform manufacturing protocols, computational modeling, and failure mode analysis for next-generation BPMs.
97 MATHEMATICS AND COMPUTING↗
"Soiling, Cleaning, and Abrasion: The Results of the Five-Year Photovoltaic Glass Coating Field Study" [Slides]
External contamination ("soiling") of the incident surface is a major limiting factor for solar technologies. A 5-year field glass coupon study was conducted to better understand external contamination and its effects; compare cleaning methods and the use of preventative coatings; and explore the abrasion resulting from cleaning to advise on accelerated abrasion testing. Test sites included the cities of Dubai (UAE), Kuwait City (Kuwait), Mesa (AZ), Mumbai (India), and Sacramento (CA). Through the 5-year cumulative study, dry brush, water spray, and wet sponge and squeegee cleaning methods were compared to no cleaning. Optical microscopy was used to obtain images, including representative color images, grayscale images for object analysis, and oblique images for coating integrity assessment. A thresholding protocol was developed to analyze and distinguish specimens using the ImageJ software. Optical performance was quantified using a spectrophotometer, including comprehensive optical characterization (transmittance, reflectance, and absorptance in addition to forward- and back-scattering). Atomic force microscopy was used to verify the abrasion damage morphology, including the width and depth of surface scratches. Analysis of the results included correlation of optical performance and particle area coverage, rank order (by coating or location), and the acceleration factor for abrasion damage. The efficacy of external cleaning was more readily distinguished from the effectiveness of antisoiling coatings. The acceleration factor for dry brush cleaning of a porous silica coating was found to be on the order of unity.
14 SOLAR ENERGY↗