Search NASA⌕ Search

SEARCH · Search NASA

Results for “band engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Noise and static performance characteristics of a STOL aircraft jet flap

Static noise and performance tests were conducted on a 1/4-scale jet flap model with a multilobe nozzle of array area ratio of 2.7. The model nozzle and flap tested were a two-dimensional section of a distributed blowing system similar to previously investigated augmentor wing systems without the upper shroud and intake door. Noise data were measured with the nozzle alone and also during attached flow conditions with the flap at two turning angles representing takeoff and approach conditions. The noise data are scaled to a 200,000-lb TOGW four-engine airplane and are presented in terms of perceived noise level and one-third octave band sound pressure level. Comparisons are made with the noise levels produced by an augmentor wing airplane fitted with a three-element acoustically lined augmentor flap. The static performance is presented in terms of thrust recovery and effective turning angle.

Harkonen, D. L.↗
NASA NTRS1981

Static noise tests on modified augmentor wing jet STOL research aircraft

Noise measurements were made to determine if recent modifications made to the bifurcated jetpipe to increase engine thrust had at the same time reduced the noise level. The noise field was measured by a 6-microphone array positioned on a 30.5m (100 ft) sideline between 90 and 150 degrees from the left engine inlet. Noise levels were recorded at three flap angles over a range of engine thrust settings from flight idle to emergency power and plotted in one-third octave band spectra. Little attenuation was observed at maximum power, but significant attenuation was achieved at approach and cruise power levels.

Cook, G. R.↗
NASA NTRS1993

Parallel-Vector Algorithm For Rapid Structural Anlysis

New algorithm developed to overcome deficiency of skyline storage scheme by use of variable-band storage scheme. Exploits both parallel and vector capabilities of modern high-performance computers. Gives engineers and designers opportunity to include more design variables and constraints during optimization of structures. Enables use of more refined finite-element meshes to obtain improved understanding of complex behaviors of aerospace structures leading to better, safer designs. Not only attractive for current supercomputers but also for next generation of shared-memory supercomputers.

Agarwal, Tarun R.↗
NASA NTRS2006

Assessment of Bulk Absorber Properties for Multi-Layer Perforates in Porous Honeycomb Liners

CONTINUING progress in materials technology provides potential for improved acoustic liners for attenuating broadband fan noise emissions from aircraft engine nacelles. Conventional liners (local-reacting perforate-over-honeycomb structures) provide significant narrow-band attenuation, but limited attenuation over wide bandwidths. Two approaches for increasing attenuation bandwidth are to (1) replace the honeycomb structure with bulk material, or (2) cascade multiple layers of perforate/honeycomb structures. Usage of the first approach is limited because of mechanical and maintenance reasons, while multi-layer liners are limited to about three layers because of their additional mechanical complexity, depth and weight. The current research concerns a novel approach reported by the University of Cincinnati, in which a single-layer conventional liner is converted into an extended-reaction, broadband absorber by making the honeycomb core structure porous. This modified single-layer liner requires no increase in depth and weight, and minimal increase in mechanical complexity. Langley has initiated research to identify potential benefits of liner structures with porous cell walls. This research has two complementary goals: (1) develop and validate experimental techniques for treating multi-layer perforates (representative of the internal cells of a liner with porous cell walls) as 1-D bulk materials, and (2) develop analytical approaches to validate this bulk material assumption. If successful, the resultant model can then be used to design optimized porous honeycomb liners. The feasibility of treating an N-layer perforate system (N porous plates separated by uniform air gaps) as a one-dimensional bulk absorber is assessed using the Two-Thickness Method (TTM), which is commonly used to educe bulk material intrinsic acoustic parameters. Tests are conducted with discrete tone and random noise sources, over an SPL range sufficient to determine the nonlinearity of the test specimens, for test specimens consisting of 5, 10 and 15% porous plates. Measured impedances for two liner thicknesses (e.g., 12 and 24 layers) are used as input to the TTM to determine the characteristic impedance and propagation constant that characterize these liners as bulk absorbers. These parameters are then used to calculate the predicted impedance of liners with different thicknesses (e.g., 36 layers), and a comparison of predicted and measured impedances for these other thicknesses is used to determine the efficacy of this approach. Finally, an independent method is used to educe the propagation constant for a single representative sample, and excellent comparison between the results for this method and those for the TTM provides increased confidence in the results achieved with the TTM. In general, the results demonstrate these multi-layer perforates can be acceptably treated as bulk absorbers.

Jones, Michael G.↗
NASA NTRS1956

Near Noise Field of a Jet-engine Exhaust II : Cross Correlation of Sound Pressures

Pressure cross correlations were obtained over a range of jet velocities both longitudinally and laterally for the overall sound pressure and for several frequency bands. The region of positive correlation was found to increase with distance downstream of the nozzle exit and was greater for lateral than for longitudinal correlations. In general, little change in the correlation curves was found as a function of jet velocity or frequency band width. Measurements made with a fixed and a movable microphone in a plate showed correlations similar to the free-field results. The results are interpreted in terms of pressure loads on surfaces.

LOADS, AERODYNAMIC↗
NASA NTRS1972

State of the art in the detection of intelligent extraterrestrial signals.

Recent progress in ideas of how signals that might represent electromagnetic radiations of intelligent civilizations elsewhere in the galaxy is summarized. Project Cyclops, carried out at Ames Research Center under the auspices of NASA and the American Society for Engineering Education, determined that microwaves are superior to lasers for interstellar signalling. It is felt that the band lying between the resonances of the two dissociation products of water, the hydrogen line at 1420 MHz, and the first hydroxyl line at 1662 MHz, is the most suitable. Phased antenna arrays of perhaps 1000 to 10,000 dishes of 100 m diam would be required. It is considered that a list of likely stars should be compiled, and these should be searched one at a time. Procedures for combing the spectrum are outlined.

Oliver, B. M.↗
NASA NTRS1972

Structural evaluation of Marman V-band coupling and flange with conoseal gasket

Results are described of a development test program directed at evaluating the structural capabilities of the Marman V-band coupling and flange with conoseal gasket. The intended end use was for the 75K NERVA flight engine propellant lines. Of major importance in the structural evaluation was the ability to predict stresses throughout the assembly for a variety of loading conditions. Computer finite element analysis was used to predict these stresses but, for the subject configuration, large uncertainties were introduced in modeling the complex geometry and boundary conditions. The purpose of the structural tests was to obtain actual stresses and deflections for correlation with, and updating of the finite element model. Results of the incomplete test program are inconclusive with respect to determining suitability for use on the NERVA engine.

Oates, J. H.↗
NASA NTRS1989

Multiple beam antenna/switch system study

In the study of the Multiple Beam Antenna/Switch for the space to ground link (SGL) uplink and downlink services, several issues related to system engineering, antenna, transmit/receive, and switch systems were addressed and the results are provided. Bandwidth allocation at Ku band is inadequate to serve the data rate requirements for the forward and return services. Rain and depolarization effects at EHF, especially at Ka band, pose a significant threat to the link availabilities at heavy rain areas. Hardware induced effects such as the nonlinear characteristics of the power amplifier may necessitate the use of linearizers and limiters. It is also important to identify the components that are susceptible to the space radiation effects and shield or redesign them with rad-hard technologies for meeting the requirements of the space environment.

Source record↗
NASA NTRS2011

Adding a Second Ku-Band Antenna to the International Space Station

The International Space Station, as originally developed, used the Ku-Band Tracking and Data Relay Satellite System communications link to transmit non-critical data to the ground. Since becoming operational, the use for the link evolved to include additional services that, although also not critical, were deemed to be necessary for the crew. The external Ku-Band Antennas were designed for transport to the ISS in the shuttle cargo bay and thus are not suitable for manifesting on any current cargo vehicle. The original intent was to stow two spare antennas on orbit in a protective container until such time as they were needed to replace a failing unit which is a long and complicated process due to the complexity of the removal and replacement procedure. The Boeing Company proposed manifesting one of those spare antennas in an operable configuration eliminating the need for an Extravehicular Activity (EVA) to correct the first failure and as such minimizing the time to hours rather than weeks required to restore the Ku-Band communications link after failures. After the first failure, an EVA would be scheduled to replace the failed antenna with the stowed spare antenna. Because the hot spare is activated internal to the ISS, the replacement of the failed unit can be done when convenient rather than in haste. This paper describes the methodology used to locate a suitable site to add a new antenna mast to the ISS as well the process followed to fabricate, deliver and install the new interface hardware. Because this was not planned when the ISS was originally designed, structural, power, data and Intermediate Frequency signal connections had to be found for use. With the movement of the P6 solar array element from the initial location in the center zenith location of the ISS to the end of the port side of the truss and concurrent relocation of one string of S-Band communications assets, there were candidate power, data and structural connections available on the Z1 Truss. The engineering team evaluated these residual interfaces for use and designed cabling and structural elements for the candidate interfaces. The antenna was recently installed on ULF-4 and has completed a preliminary checkout. Included in this check out were evaluation of the power level received from the TDRS and evaluation of the gimbal position feedback for consideration in the static bias pointing matrix. This process demonstrates the ability to modify and upgrade manned space vehicles as either need or technology requires.

DuSold, Chuck↗
NASA NTRS2012

First Results from an Airborne Ka-Band SAR Using SweepSAR and Digital Beamforming

SweepSAR is a wide-swath synthetic aperture radar technique that is being studied for application on the future Earth science radar missions. This paper describes the design of an airborne radar demonstration that simulates an 11-m L-band (1.2-1.3 GHz) reflector geometry at Ka-band (35.6 GHz) using a 40-cm reflector. The Ka-band SweepSAR Demonstration system was flown on the NASA DC-8 airborne laboratory and used to study engineering performance trades and array calibration for SweepSAR configurations. We present an instrument and experiment overview, instrument calibration and first results.

instrument calibration↗
NASA NTRS2022

Thermal Imaging of Dust Hiding the Black Hole in NGC 1068

In the widely accepted ‘unified model’1 solution of the classification puzzle of active galactic nuclei, the orientation of a dusty accretion torus around the central black hole dominates their appearance. In ‘type-1’ systems, the bright nucleus is visible at the centre of a face-on torus. In ‘type-2’ systems the thick, nearly edge-on torus hides the central engine. Later studies suggested evolutionary effects2 and added dusty clumps and polar winds3 but left the basic picture intact. However, recent high-resolution images4 of the archetypal type-2 galaxy NGC 10685,6, suggested a more radical revision. The images displayed a ring-like emission feature that was proposed to be hot dust surrounding the black hole at the radius where the radiation from the central engine evaporates the dust. That ring is too thin and too far tilted from edge-on to hide the central engine, and ad hoc foreground extinction is needed to explain the type-2 classification. These images quickly generated reinterpretations of the dichotomy between types 1 and 27,8. Here we present new multi-band mid-infrared images of NGC 1068 that detail the dust temperature distribution and reaffirm the original model. Combined with radio data ( J.F.G. and C.M.V.I., manuscript in preparation), our maps locate the central engine that is below the previously reported ring and obscured by a thick, nearly edge-on disk, as predicted by the unified model. We also identify emission from polar flows and absorbing dust that is mineralogically distinct from that towards the Milky Way centre.

Violeta Gamez Rosas↗
NASA NTRS2011

Engineering Challenges for Active Debris Removal

Recent modeling studies on the instability of the debris population in the low Earth orbit (LEO) region and the collision between Iridium 33 and Cosmos 2251 have underlined the need for active debris removal. A 2009 analysis by the NASA Orbital Debris Program Office shows that, in order to maintain the LEO debris population at a constant level for the next 200 years, an active debris removal of about five objects per year is needed. The targets identified for removal are those with the highest mass and collision probability products in the environment. Many of these objects are spent upper stages with masses ranging from 1 to more than 8 metric tons, residing in several altitude regions and concentrated in about 10 inclination bands. To remove five of those objects on a yearly basis, in a cost-effective manner, represents many challenges in engineering, technology development, and operations. This paper outlines a conceptual end-to-end debris removal operation, including launch, precision tracking, rendezvous, stabilization (of the tumbling targets), capture, and deorbit of the targets; and highlights major challenges associated with the operations. Pros and cons of several proposed removal techniques are also evaluated.

Liou, Jer-Chyi↗
NASA NTRS2020

Detecting differential ground displacements of civil structures in fast-subsiding metropolises with interferometric SAR and band-pass filtering

Ground displacements due to changes in soil conditions represent a threat to the stability of civil structures in many urban areas, worldwide. In fast-subsiding areas, regional subsidence (wavelength ~ 1,000’s m) can be dominantly high and, consequently, mask other signals at local scales (wavelength ~ 10–100’s m). Still, engineering and construction applications require a comprehensive knowledge of local-scale signals, which can threaten the stability of buildings and infrastructure. Here we present a new technique based on band-pass filters for uncovering local-scale signals hidden by regional subsidence as detected by interferometric SAR measurements. We apply our technique to a velocity field calculated from 21 high-resolution COSMO-SkyMed scenes acquired over Mexico City and obtain components of long (> 478 m), intermediate (42–478 m) and short (< 42 m) spatial wavelengths. Our results reveal that long-wavelength velocities exceed − 400 mm/year, whereas intermediate- and short-wavelength velocities are in the order of ± 15 mm/year. We show that intermediate-wavelength velocities are useful for retrieving signals such as uplift along elevated viaducts of Metro lines 4 and B, as well as differential displacements in Pantitlán station’s pedestrian overpass system and across sharp geotechnical boundaries in the piedmont of Sierra de Santa Catarina—where surface faulting occurs.

Darío Solano-Rojas↗
NASA NTRS2019

Evaluation of NOAA-20 VIIRS reflective solar bands calibration performance using vicarious approaches

The newly launched polar-orbiting NOAA-20 satellite is the follow-on mission to the SNPP (Suomi National Polar-orbiting Partnership) satellite. Both satellites are in an afternoon orbit with a close equatorial cross time. The Visible Infrared Imaging Radiometer Suite (VIIRS) is a key sensor onboard NOAA-20 and SNPP. The two VIIRS sensors are within the same engineering design with nearly identical spectral ranges. Its on-board calibration components include a solar diffuser and a solar diffuser stability monitor for the reflective solar bands (RSB), a V-groove blackbody for the thermal emissive bands (TEB), and a space view as background reference. This study evaluates calibration performance of the NOAA-20 VIIRS RSB using the first internally released L1B data product by NASA Land SIPS, which has consistent calibration coefficient look up tables (LUT) throughout the entire mission. Several independent vicarious approaches are used to examine the stability and consistence of reflectance. The first approach is based on a double difference method by comparison with SNPP VIIRS using observations from simultaneous nadir overpasses (SNO) with Aqua MODIS. The second is based on the reflectance trends from 16-day repeatable orbits obtained over the widely used Liby-4 desert site so each data point has the nearly same viewing angles relative to the site. The third approach is to use the frequent overpasses over the Dome C snow site. Results of this study provide NOAA-20 VIIRS post-launch calibration stability performance and radiometric agreement with SNPP for the first 18 months of mission.

VIIRS↗
NASA NTRS1976

Teledyne Continental Motors emissions data and analysis and flight test results

Five different engine models were tested covering combinations of all engine categories in current production in the range from 100 to 435 brake horsepower. Engines were divided into five major types: carbureted, fuel injected, direct drive, geared, and turbocharged. Emissions data were categorized by three separate fuel system schedules: baseline, case 1, and case 2. Baseline was defined as the average fuel flow rate established by the fuel system's production tolerance band when operated with the mixture control at the full-rich position. Case 1 was defined as the minimum allowable fuel flow rate established by the engine certification. Case 2 was defined as the fuel rate corresponding to the leanest fuel-air ratio obtainable before a safety limit occurred with the engine operating on a propeller test stand. Safety limits that developed during testing were cylinder-head overheating or inadequate acceleration from a given mode of operation.

Rezy, B. J.↗
NASA NTRS1981

Failure analysis of a tool steel torque shaft

A low design load drive shaft used to deliver power from an experimental exhaust heat recovery system to the crankshaft of an experimental diesel truck engine failed during highway testing. An independent testing laboratory analyzed the failure by routine metallography and attributed the failure to fatigue induced by a banded microstructure. Visual examination by NASA of the failed shaft plus the knowledge of the torsional load that it carried pointed to a 100 percent ductile failure with no evidence of fatigue. Scanning electron microscopy confirmed this. Torsional test specimens were produced from pieces of the failed shaft and torsional overload testing produced identical failures to that which had occurred in the truck engine. This pointed to a failure caused by a high overload and although the microstructure was defective it was not the cause of the failure.

Reagan, J. R.↗
NASA NTRS2013

Performance Testing of the Engineering Model Astro-H 3-stage ADR

The Japanese Astro-H mission will include the Soft X-ray Spectrometer (SXS) instrument provided by NASA/GSFC. The SXS will perform imaging spectroscopy in the soft x-ray band using a 6x6 array of silicon microcalorimeters operated at 50 mK. The detectors are cooled by a 3-stage adiabatic demagnetization refrigerator (ADR), which is configured to use either a 1.3 K superfluid helium tank or a 4.5 K Joule-Thomson cryocooler as a heat sink. At present, the engineering model SXS, including the detectors and ADR, has been performance tested at GSFC and integrated with the EM dewar in Japan. The flight model SXS is currently being fabricated. This paper presents test results of the EM ADR and changes that will be implemented in the flight version.

Shirron, Peter J.↗