Search NASA⌕ Search

SEARCH · Search NASA

Results for “binders”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Carbon-Binder Optimization for Lithium-Ion Battery Extreme Fast Charge

Battery performance is strongly correlated with electrode microstructure and weight loading of the electrode components. Among them are the carbon-black and binder additives that enhance effective conductivity and provide mechanical integrity. However, these both reduce effective ionic transport in the electrolyte phase and reduce energy density. Therefore, an optimal additive loading is required to maximize performance, especially for fast charging where ionic transport is essential. Such optimization analysis is however challenging due to the nanoscale imaging limitations that prevent characterizing this additive phase and thus quantifying its impact on performance. Herein, an additive-phase generation algorithm has been developed to remedy this limitation and identify percolation threshold used to define a minimal additive loading. Improved ionic transport coefficients from reducing additive loading has been then quantified through homogenization calculation, macroscale model fitting, and experimental symmetric cell measurement, with good agreement between the methods. Rate capability test demonstrates capacity improvement at fast charge at the beginning of life, from 37% to 55%, respectively for high and low additive loading during 6C CC charging, in agreement with macroscale model, and attributed to a combination of lower cathode impedance, reduced electrode tortuosity and cathode thickness.

carbon-binder additives↗
DOE OSTI2020

The Influence of Printing Parameters, Post-Processing, and Testing Conditions on the Properties of Binder Jetting Additive Manufactured Functional Ceramics

This article outlines the current state-of-the-art binder jetting (BJT) additive manufacturing of functional ceramics. The impact of printing parameters, heat treatment processing, and testing conditions on the observed performance of these ceramics is discussed. Additionally, this article discusses the impact of physical properties such as density and mechanical strength on the overall performance of these functional ceramics. Although printing parameters and initial feedstock are crucial for the printability of the desired parts, other factors play an important role in the performance of the ceramic. Thermal post-processing is crucial to achieve optimized functional properties, while the testing orientation is key to obtaining the maximum output from the part. Finally, future research directions for this field are also discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Binder Jet Additive Manufacturing Process and Material Characterization for High Temperature Heat Exchangers Used in Concentrated Solar Power Applications

The U.S. Department of Energy’s (DOE) Sunshot 2030 initiative has a goal of reducing the cost of concentrating solar power (CSP) to 5 cents per kWh for baseload power plants. One of the potential pathways to this goal includes a reduction in the cost of the supercritical CO2 (sCO2) power block to 0.9 cents per kWh. Recuperators—high and low temperatures, used in the sCO2 power cycle, contribute to >50% of the cost of the power cycle. This work studies the feasibility towards a ≥10% cost reduction for High Temperature Recuperators (HTR) used in the sCO2 power cycle. One way to address the cost reduction is by leveraging low-cost additive manufacturing, specifically, Binder Jet Additive Manufacturing (BJAM) to 3D print HTRs at scale. This study focuses on the development of a BJAM process towards 3D printing HTR cores using Stainless Steel alloy 316L (SS316L). To evaluate the suitability of the BJ process towards the HTR, high level specifications of the application are translated to materials capability requirements. Subsequently, at-temperature materials testing is conducted on as-printed and sintered additively manufactured coupons. Data from the coupons are compared against cast and wrought SS316L data obtained from the literature. Results show that the tensile properties from the BJ process compare well against cast properties. Furthermore, a baseline analysis of creep testing data is established for the BJ process, and insights are drawn from the results towards future improvements of the process.

14 SOLAR ENERGY↗
DOE OSTI2026

Powder‐to‐Film Conversion of Nickel Single‐Atom Catalysts into Binder‐Free and Resistant Electrodes

Although a few binder-free and self-supported single-atom electrodes have been reported, achieving mechanically robust, defect-engineered, and reproducible films that preserve atomic dispersion under electrochemical operation remains challenging. This work addresses this limitation by presenting a versatile and generalizable strategy to transform powders into standalone, defect-engineered thin films hosting atomically dispersed Ni centers within conductive 2D frameworks. The physicochemical and electronic properties of these materials are thoroughly characterized using a comprehensive set of spectroscopic and microscopic techniques and confirmed the homogeneous dispersion and monoatomic nature of the Ni centers (0.94 wt.%) on the electrode films. Electrochemical testing via cyclic voltammetry and electrochemical impedance spectroscopy under a range of experimental conditions revealed that integration of Ni single atoms markedly enhanced performance and stability compared to carbon nanotube-only electrodes, maintaining integrity after 15 h of continuous operation. This improvement is accompanied by a notable reduction in charge transfer resistance (30.50 Ω) and an increase in double-layer capacitance (295.45 µF). Post-electrochemical analyses corroborated the structural integrity and robustness of the electrodes. Overall, this work bridges atomically precise catalysis and device-level electrochemistry, opening a route toward reproducible and scalable single-atom electrodes for sensing and energy conversion.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Hydrocarbon Ionomeric Binders for Fuel Cells and Electrolyzers

Abstract Ionomeric binders in catalyst layers, abbreviated as ionomers, play an essential role in the performance of polymer–electrolyte membrane fuel cells and electrolyzers. Due to environmental issues associated with perfluoroalkyl substances, alternative hydrocarbon ionomers have drawn substantial attention over the past few years. This review surveys literature to discuss ionomer requirements for the electrodes of fuel cells and electrolyzers, highlighting design principles of hydrocarbon ionomers to guide the development of advanced hydrocarbon ionomers.

25 ENERGY STORAGE↗
DOE OSTI2020

Metal Powder Recyclability in Binder Jet Additive Manufacturing

The recyclability of 316L stainless steel powder in the binder jetting process has been determined. The powder characterization results demonstrated a 22% increase in the number of coarse particles (> 30 µm) and an 18.2% reduction in the number of small particles (< 10 µm) after recycling up to 16 times. A few elongated and irregular-shaped particles were found after recycling, possibly due to particle agglomeration during handling and sieving. Here, a negligible increase in the oxygen content by 0.036% was detected in the recycled powder. The density of sintered parts produced using recycled powder was approximately 1.5% lower than when using fresh powder due to the changes in the particle size distribution and the flowability of the powder caused by the changes in morphology. Final parts built using fresh and recycled powder showed similar hardness (155 ± 3 HV and 165 ± 9 HV) and yield strength (206 ± 16 MPa and 192 ± 10 MPa), respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Combined DSC/TGA Analysis to Rationalize the As-Sintered Microstructure in Binder Jet Additively Manufactured H13 Tool Steel

In this study, a combined DSC/TGA analysis has been used to rationalize the constant liquid channel width at higher sintering temperatures in H13 tool steel manufactured by binder jet additive manufacturing. Using enthalpy conservation along with coupled DSC + TGA analysis, the phase fractions of liquid and austenite phases during heating and cooling respectively were estimated. The estimates from the DSC/TGA analysis were compared with equilibrium phase fraction predictions from ThermoCalc. The resulting phase evolution was correlated to the as-sintered microstructure to rationalize the unexpected lack of change in liquid channel width at higher sintering temperatures.

Kannan, Rangasayee↗
DOE OSTI2022

Binder jet additive manufacturing of ceramic heat exchangers for concentrating solar power applications with thermal energy storage in molten chlorides

Triply periodic minimal surface (TPMS) geometries can only be fabricated by additive manufacturing methods and are of interest for heat exchangers. Ceramic TPMS heat exchangers can operate at higher temperatures and pressures with superior performance and increased operating efficiencies compared to metal heat exchangers. The properties of ultra-high temperature ceramic (UHTC) materials are also favorable for heat exchangers and potentially suited to concentrated solar power (CSP) systems, such as those based on a molten chloride salt thermal energy storage (TES) medium used to heat CO 2 in a closed-loop Brayton power cycle. We intended to demonstrate binder jet additive manufacturing feasibility of a UHTC-TPMS structure by printing and sintering a null candidate. We aimed to achieve parts with a relative density ≥ 92 % of theoretical and to provide a TPMS part demonstration. The target density indicates the transition from intermediate to final stage sintering, a requirement to inhibit gas permeability and for sintering complex near net shapes to full density with sinter-HIP technology. The goal of the TPMS part demonstration was to determine if printing and sintering parameters developed from test coupons apply to the complex geometries that will eventually be used in a heat exchanger design. Our objective was to print cubic TPMS parts with a 9 cm 3 volume and sinter it without distorting and cracking. We report we were able to sinter ZrB 2 -MoSi 2 composite parts based on the Schwarz-D TPMS and achieve isotropic shrinkage up to 60 % by volume, resulting in densities ranging from 92 % to 96 % of theoretical.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Effect of thermal treatments on electrochemical behavior of binder jetted 17-4 PH stainless steel

Binder jetted 17–4 PH stainless steel was post-processed to relate heat treatment, microstructure, and corrosion in 3.5 wt% NaCl. Specimens were sintered at 1380 or 1400 °C, solution-annealed at 1055 °C for 1 h, and aged at 482 °C for 1 h. Here, as-sintered parts showed α′-martensitic matrix with a δ-ferrite network and Cu-rich precipitates in ferrite; inclusions (MnS, NbC) promoted localized attack. solutionizing redistributed elements and reduced ferrite, while aging generated coherent Cu nano-precipitates. Corrosion resistance was highly sensitive to post-processing in which aged specimens exhibited the lowest corrosion current density and formed a thicker, stable Cr 2 O 3 -rich passive film, whereas sintered specimens degraded most. Pitting potential depended on sintering temperature and microstructure, with 1400 °C sintering yielding more positive pitting potentials and the best overall performance after aging. Although the 1400-solutionized condition showed a relatively noble pitting response versus 1380-solutionized, it displayed unstable corrosion kinetics attributed to an imperfect passive film linked to higher NbC density. XPS depth profiles corroborated these trends, showing thicker, more continuous Cr 2 O 3 in aged states and discontinuous/thinning oxides in less resistant conditions. Practically, high-temperature sintering (∼1400 °C) followed by solutionizing and aging is recommended, with further gains expected from reducing NbC/MnS populations and porosity via powder and process control.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Binder-free thin graphite fiber mat sandwich electrode architectures for energy-efficient vanadium redox flow batteries

Vanadium redox flow batteries (VRFB) are emerging as the preferred energy storage solution for long-duration energy storage (LDES) and grid-scale load levelling. In this study, we report a novel binder-free sandwich electrode architecture consisting of a thin layer (6–12 mg cm –2 ) of thermally activated graphite felt mat (TGFM) sandwiched between thin carbon papers (TCP-TGFM-TCP). This electrode architecture substantially reduced the polarization (I-V) resistance of the VRFB by 23 %, resulting in a current density increase from 340 mA cm –2 at 1 V for the thermally activated graphite felt (TGF) electrode to 470 mA cm –2 at 1 V, and an energy efficiency of 80 % at 100 mA cm –2 is realized.

25 ENERGY STORAGE↗
DOE OSTI2021

Effect of PCEs with different structures on hydration and properties of cementitious materials with low water-to-binder ratio

Polycarboxylate ethers (PCEs) with different structures and densities of anchor groups in the backbone were synthesized and characterized. The surface tension of their solutions, their adsorption on cementitious particles and zeta potential of cement-silica fume pastes with PCEs were measured. Their effects on hydration and properties of cement-silica fume paste with low water-to-binder ratio were examined. Results indicated that the adsorption kinetics of theses PCEs on cementitious particles are fitted the pseudo-second-order model. The introduction of long silane chain on PCE decreased its electrostatic adsorption, while PCE was adsorbed onto the surface of particles via both chemical and electrostatic adsorption, when silicon hydroxyl is directly connected to its backbone. In the presence of PCE with higher adsorbed amount, pastes exhibited lower yield stress and higher flowability, and higher strength at 7 d and 28 d. The low plastic viscosity, autogenous and drying shrinkage were related to the low surface tension of PCE solution.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Understanding geopolymer binder-aggregate interfacial characteristics at molecular level

The interfacial characteristics of geopolymer binder to aggregate composites are poorly understood, especially at molecular level. Herein, molecular models are developed to study, for the first time, the geopolymer-aggregate interface. Chemically, various forms of interfacial bonding are characterized, including Al-O-Si bonding through condensation reactions, NaO and H-bonding. An atomic-level interfacial transition zone (ITZ) is identified, attributed to the concentration of –OH groups. Increasing the Si/Al ratio of geopolymer is found to decrease the ITZ density, but have limited effect on the ITZ width. A heterogeneous diffusion characteristic occurs in geopolymer, due to the weak interfacial interaction. Mechanically, lowering the Si/Al ratio promotes the interfacial strength due to the stronger interfacial interaction and higher cross-linking degree in geopolymer. Under loading the interfacial fracture undergoes three stages: crack propagation, chain bridging (including aluminosilicate and ionic bridging) and breakage. The above atomic-level findings may facilitate a better design of geopolymer concrete in engineering.

36 MATERIALS SCIENCE↗