SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
To achieve high thermal-to-electric energy conversion efficiency, it is desirable to operate thermoelectric generator devices over large temperature gradients and also to maximize the performance of the thermoelectric materials used to build the devices.
Current NASA lunar architecture calls for permanent human habitation of the moon by the year 2020. Due to the expense of delivering materials into orbit, technologies are being developed to use lunar regolith for building and as a material resource for fabrication, oxygen production, and other needs. Additionally, constant exposure to the finest size fraction of lunar regolith may present hazards to human health. Towards developing these technologies and mitigating hazards, lunar regolith simulants are becoming an increasingly important part of the development paradigm.
The Gravity and Extreme Magnetism Small Explorer (GEMS) X-ray polarimeter Instrument (XPI) was designed to measure the polarization of 23 sources over the course of its 9 month mission. The XPI design consists of two telescopes each with a polarimeter assembly at the focus of a grazing incidence mirror. To make sensitive polarization measurements the GEMS Polarimeter Assembly (PA) employed a gas detection system based on a Time Projection Chamber (TPC) technique. Gas detectors are inherently at risk of degraded performance arising from contamination from outgassing of internal detector components or due to loss of gas. This paper describes the design and the materials used to build a prototype of the flight polarimeter with the required GEMS lifetime. We report the results from outgassing measurements of the polarimeter subassemblies and assemblies, enclosure seal tests, life tests, and performance tests that demonstrate that the GEMS lifetime is achievable. Finally we report performance measurements and the lifetime enhancement from the use of a getter.
Analysis of phase I specimens produced as part of the 3D printing in zero G technology demonstration mission exhibited some differences in structure and performance for specimens printed onboard the International Space Station (ISS) and specimens produced on the ground with the same printer prior to its launch. This study uses the engineering test unit for the printer, identical to the unit on ISS, to conduct a ground-based investigation of the impact of the distance between the extruder tip and the build tray on material outcomes. This standoff distance was not held constant for the phase I flight prints and is hypothesized to be a major source of the material variability observed in the phase I data set.
Efforts to build a Predictive Material Modeling (PMM) framework from the micro-scale to the macro-scale are presented in this abstract. To reduce the need for extensive testing, accelerate the design cycle process, and reduce uncertainty margins applied to final designs, NASA is developing simulation and modeling tools that enable characterization of material properties and response to high-enthalpy environments. The Porous Microstructure Analysis (PuMA) code has been developed for computing macroscale (volume averaged) properties of porous materials using microscale images from micro-computed tomography (micro-CT). Microscale modeling requires a realistic representation of a material microstructure; these are obtained either synthetically during the design of the material or through X-ray micro-CT. Volume averaged properties are then used to inform macroscale material response models, such as those implemented in the Porous-material Analysis Toolbox based on OpenFOAM (PATO) software, also actively developed by NASA. The computational model in PATO is a generic heat and mass transfer model for porous reactive materials containing several solid phases and a single gas phase. The detailed chemical interactions occurring between the solid phases and the gas phase are modeled at the pore scale assuming local thermal equilibrium. These tools were developed to efficiently interface with other pre-existing codes such as SPARTA (direct simulation Monte Carlo), DPLR (hypersonic CFD), NEQAIR (radiative transport) and DAKOTA (uncertainty quantification and optimization). Detailed flight data (Mars Science Laboratory [MSL] Entry Descent and Landing Instrument [MEDLI]) is critical for validating these computational tools for NASA applications. Examples of modeling ablative material response using these codes will be presented including 3D simulations of the full-scale heatshield of the MSL capsule. The simulations demonstrate the ability of the modern material response code, PATO, to handle the material response of geometrically complex and large domains, through the use of massively parallel computations.
To achieve high thermal-to-electric energy conversion efficiency, it is desirable to operate thermoelectric geneteor devices over large temperature gradients and also to maximize the thermoelectric performance of the materials used to build the devices.
Efforts to build a Predictive Material Modeling (PMM) framework from the micro-scale to the macro-scale are presented in this abstract. To reduce the need for extensive testing, accelerate the design cycle process, and reduce uncertainty margins applied to final designs, NASA is developing simulation and modeling tools that enable characterization of material properties and response to high-enthalpy environments. The Porous Microstructure Analysis (PuMA) code has been developed for computing macroscale (volume averaged) properties of porous materials using microscale images from micro-computed tomography (micro-CT). Microscale modeling requires a realistic representation of a material microstructure; these are obtained either synthetically during the design of the material or through X-ray micro-CT. Volume averaged properties are then used to inform macroscale material response models, such as those implemented in the Porous-material Analysis Toolbox based on OpenFOAM (PATO) software, also actively developed by NASA. The computational model in PATO is a generic heat and mass transfer model for porous reactive materials containing several solid phases and a single gas phase. The detailed chemical interactions occurring between the solid phases and the gas phase are modeled at the pore scale assuming local thermal equilibrium. These tools were developed to efficiently interface with other pre-existing codes such as SPARTA (direct simulation Monte Carlo), DPLR (hypersonic CFD), NEQAIR (radiative transport) and DAKOTA (uncertainty quantification and optimization). Detailed flight data (Mars Science Laboratory [MSL] Entry Descent and Landing Instrument [MEDLI]) is critical for validating these computational tools for NASA applications. Examples of modeling ablative material response using these codes will be presented including 3D simulations of the full-scale heatshield of the MSL capsule. The simulations demonstrate the ability of the modern material response code, PATO, to handle the material response of geometrically complex and large domains, through the use of massively parallel computations.
Design for Additive Manufacturing (DfAM) is widely used to describe design activities and guidelines employed in the creation of Additively Manufactured (AM) parts. Basic design rules for widely adopted processes like Powder Bed Fusion (PBF) are relatively understood including material performance, part size constraints, self-supporting angles, overhangs, wall thicknesses, and feature resolution. Complexity is often inherent with PBF using organically inspired solutions through generative design and topology optimization software to create designs that often cannot be realized via traditional manufacturing processes. The design rules for Directed Energy Deposition (DED) are less well known, and, in some cases, the lack of understanding is likely inhibiting broader application of the various DED processes. This presentation covers key design rules for DED fusion processes and elucidates opportunities like multi-material deposition and build approaches ranging from basic features to complex large-scale parts. Complementary to the opportunistic characteristics of DfAM for DED, Manufacture for AM (MfAM) encompasses the restrictive aspects of the manufacturing lifecycle with limitations due to bead width and wall thickness, self-supporting angles, surface texture, microstructural evolution, and residual stresses. AM enabled part design must always consider the entire value chain starting with incoming feedstock (e.g. plate, wire, or powder) and progressing through the printing process, post-processing (e.g. machining, inspection), and final system assembly. Key considerations, like the tradeoffs between feature resolution and build rate, for process and part selection and economic assessments will be discussed as DED is often traded against other AM processes. After highlighting typical DED design rules, we will also show how some of those rules can be broken via use cases and part designs that span the full spectrum of DED processes with examples of various DED part designs.
Room Temperature Vulcanizing silicone (RTV) is a high-temperature adhesive that has successfully been used as a gap-filler between Thermal Protection System (TPS) tiles for heatshields on numerous missions. It is also used to bond instrumentation plugs such as temperature and pressure sensors into the heatshields. While RTV has been traditionally assumed to be a non-porous and non-ablating material, numerous experiments have shown that RTV pyrolyzes and becomes highly porous as it is heated. Heating RTV has also shown swelling, or intumescence, which can pose unique problems that lead to roughness induced boundary-layer transition, surface oxide formation and contamination of heat shield sensors. Therefore, it is crucial to understand and model the intumescence phenomenon of RTV. As data for RTV material properties is limited, the first step in modeling RTV is to collect material properties such as pyrolysis mass-loss, microstructure change, virgin and char porosity, etc. which was performed in our initial study. Additionally, thermomechanical properties such as Young’s modulus and Poisson ratio are required for modeling the intumescence of RTV, which were taken from literature and the coefficient of thermal expansion was collected using in-situ heating and Micro Computed Tomography (µ-CT) in previous studies. Finally, numerous other properties such as pyrolysis gas properties, virgin and char thermal conductivity and specific heat were compiled from previous experiments and literature into a material database that can be used for simulations. In Porous Material Analysis Toolbox based on OpenFOAM (PATO) [4], structural mechanics coupled with material response was used for simulating the intumescence of RTV as it is heated. However, since the permeability of the material is very low, the pyrolysis gas creates an internal pressure build-up as the material is being heated, significantly contributing to the deformation of the material. To correctly characterize this phenomenon, additional physics models were implemented into PATO's stress analysis solver, and results were compared with RTV dilatometry test data as a preliminary verification case. Future work will include experiments of RTV at the Plasmatron X facility and the in-situ heating cell with µ-CT, and improvement of simulation tools to more accurately model RTV intumescence.
Room Temperature Vulcanizing silicone (RTV) is a high-temperature adhesive that has successfully been used as a gap-filler between Thermal Protection System (TPS) tiles for heatshields on numerous missions. It is also used to bond instrumentation plugs such as temperature and pressure sensors into the heatshields. While RTV has been traditionally assumed to be a non-porous and non-ablating material, numerous experiments have shown that RTV pyrolyzes and becomes highly porous as it is heated. Heating RTV has also shown swelling, or intumescence, which can pose unique problems that lead to roughness induced boundary-layer transition, surface oxide formation and contamination of heat shield sensors. Therefore, it is crucial to understand and model the intumescence phenomenon of RTV. As data for RTV material properties is limited, the first step in modeling RTV is to collect material properties such as pyrolysis mass-loss, microstructure change, virgin and char porosity, etc. which was performed in our initial study. Additionally, thermomechanical properties such as Young’s modulus and Poisson ratio are required for modeling the intumescence of RTV, which were taken from literature and the coefficient of thermal expansion was collected using in-situ heating and Micro Computed Tomography (µ-CT) in previous studies. Finally, numerous other properties such as pyrolysis gas properties, virgin and char thermal conductivity and specific heat were compiled from previous experiments and literature into a material database that can be used for simulations. In Porous Material Analysis Toolbox based on OpenFOAM (PATO) [4], structural mechanics coupled with material response was used for simulating the intumescence of RTV as it is heated. However, since the permeability of the material is very low, the pyrolysis gas creates an internal pressure build-up as the material is being heated, significantly contributing to the deformation of the material. To correctly characterize this phenomenon, additional physics models were implemented into PATO's stress analysis solver, and results were compared with RTV dilatometry test data as a preliminary verification case. Future work will include experiments of RTV at the Plasmatron X facility and the in-situ heating cell with µ-CT, and improvement of simulation tools to more accurately model RTV intumescence.
Aerospace structures comprised of composite materials are traditionally certified empirically via the Building Block Approach (BBA). While this approach has been performed successfully in the past, it is expensive and time consuming. One means to improve the overall efficiency of composite structural certification is to reduce the cost of the BAA by eliminating the need for some tests by incorporating damage analysis tools. For an analysis to replace a given test, the tool must first be validated using other similar test data. The subject of this paper is a description of an analysis technique for simulating compression after damage strength of a solid laminate. The analysis technique is one that is practical for use in an applied engineering context due to efforts to minimize necessary computational resources and complexity of the model.
Aerospace structures comprised of composite materials are traditionally certified empirically via the Building Block Approach (BBA). While this approach has been performed successfully in the past, it is expensive and time-consuming. One means to improve the overall efficiency of composite structural certification is to reduce the cost of the BBA by eliminating the need for some tests by incorporating damage analysis tools. For an analysis to replace a given test, the tool must first be validated using other similar test data. The subject of this paper is a description of an efficient analysis technique for simulating compression after damage strength of a solid laminate. The analysis technique is one that is practical for use in an applied engineering context due to efforts to minimize necessary computational resources and complexity of the model.
The present study demonstrates our in-house material response solver, Icarus's capability to simulate the ablative conditions, including pyrolysis effects due to the interaction between hypersonic boundary layers and the thermal protection system (TPS). A conceptual aeroshell shoulder design, which undergoes mission-relevant flow and material conditions, is selected for the demonstration purpose. LAURA, a structured flow solver, is used to solve flow around the shoulder at several trajectory points of a flight path. The aerothermal dataset obtained from LAURA is used to enforce boundary conditions on the aeroshell wall to simulate ablation processes. The two-layered material system is stacked with HEEET (TPS) and Aluminum (actual material). A set of base parameters, such as the angle of material orientation with respect to the flow direction, convective heat-transfer co-efficient, and aerothermal boundary conditions on the rear end of the HEEET material layer, is selected to conduct a base-case simulation. A small amount of recession was observed, indicating that the design should be fine to go through the selected flow and material conditions. Furthermore, the parameters mentioned above are individually altered and are observed to affect the shoulder design's recession compared to the base case. Verification of our Icarus setup was also carried out using a one-dimensional grid and FIAT, a one-dimensional material-response solver, to build credibility for our results. As the current work is an uncoupled fluid-material-response simulation, a local sharp mesh deformation in the recessed surface near the shoulder corner is observed.
To build a permanent orbiting space station in the next decade is NASA's most challenging and exciting undertaking. The space station will serve as a center for a vast number of scientific products. As a potential material for the space station, reinforced concrete was studied, which has many material and structural merits for the proposed space station. Its cost-effectiveness depends on the availability of lunar materials. With such materials, only 1 percent or less of the mass of a concrete space structure would have to be transported from earth.
Long-duration surface missions to the Moon and Mars will require bases to accommodate habitats for the astronauts. Transporting the materials and equipment required to build the necessary habitats is costly and difficult. The materials chosen for the habitat walls play a direct role in protection against each of the mentioned hazards. Choosing the best materials, their configuration, and the amount required is extremely difficult due to the immense size of the design region. Clearly, an optimization method is warranted for habitat wall design. Standard optimization techniques are not suitable for problems with such large search spaces; therefore, a habitat wall design tool utilizing genetic algorithms (GAs) has been developed. GAs use a "survival of the fittest" philosophy where the most fit individuals are more likely to survive and reproduce. This habitat design optimization tool is a multiobjective formulation of up-mass, heat loss, structural analysis, meteoroid impact protection, and radiation protection. This Technical Publication presents the research and development of this tool as well as a technique for finding the optimal GA search parameters.
Systems and methods in accordance with embodiments of the invention implement additive manufacturing techniques that employ different sets of deposition characteristics and/or material formation characteristics during the additive manufacture of an object so as to strategically build up the object. In many embodiments, material used to build up an object is deposited at different deposition rates during the additive manufacture of the object, and the object is thereby strategically built up. In one embodiment, a method of additively manufacturing an object includes: depositing material onto a surface at a first deposition rate so as to define a first region of the object to be additively manufactured; and depositing material onto a surface at a second deposition rate so as to define a second region of the object to be additively manufactured; where the second deposition rate is different from the first deposition rate.
Spacecraft dielectric charging, sometimes called deep-dielectric-charging or bulk-charging, occurs when high energy electrons imbed themselves in dielectric materials, and the charge density builds up, sometimes to breakdown levels. Charges usually bleed off slowly due to material conductivity. At very low (cryogenic) temperatures, the dielectric conductivity decreases until charges may remain and build up over weeks, months, or years. In those cases, the guidelines given in NASA and industry documents for when dielectric charging may become important are misleading. Arcing tests of spacecraft cables at liquid nitrogen temperatures and very low flux levels have been done at NASA MSFC for the JWST Project. In this paper, we describe the results of those tests and analyze their important implications for cryogenic spacecraft cable design and construction.
Spacecraft dielectric charging, sometimes called deep-dielectric-charging or bulk-charging, occurs when high energy electrons imbed themselves in dielectric materials, and the charge density builds up, sometimes to breakdown levels. Charges usually bleed off slowly due to material conductivity. At very low (cryogenic) temperatures, the dielectric conductivity decreases until charges may remain and build up over weeks, months, or years. In those cases, the guidelines given in NASA and industry documents for when dielectric charging may become important are misleading. Arcing tests of spacecraft cables at liquid nitrogen temperatures and very low flux levels have been done at NASA MSFC for the JWST Project. In this paper, we describe the results of those tests and analyze their important implications for cryogenic spacecraft cable design and construction.