Search NASA⌕ Search

SEARCH · Search NASA

Results for “climbing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Performance improvements of an F-15 airplane with an integrated engine-flight control system

An integrated flight and propulsion control system has been developed and flight demonstrated on the NASA Ames-Dryden F-15 research aircraft. The highly integrated digital control (HIDEC) system provides additional engine thrust by increasing engine pressure ratio (EPR) at intermediate and afterburning power. The amount of EPR uptrim is modulated based on airplane maneuver requirements, flight conditions, and engine information. Engine thrust was increased as much as 10.5 percent at subsonic flight conditions by uptrimming EPR. The additional thrust significantly improved aircraft performance. Rate of climb was increased 14 percent at 40,000 ft and the time to climb from 10,000 to 40,000 ft was reduced 13 percent. A 14 and 24 percent increase in acceleration was obtained at intermediate and maximum power, respectively. The HIDEC logic performed fault free. No engine anomalies were encountered for EPR increases up to 12 percent and for angles of attack and sideslip of 32 and 11 degrees, respectively.

Myers, Lawrence P.↗
NASA NTRS1988

Flight-management strategies for escape from microburst encounters

An effort is underway by NASA, FAA, and industry to reduce the threat of convective microburst wind shear phenomena to aircraft. The goal is to develop and test a candidate set of strategies for recovery from inadvertent microburst encounters during takeoff. Candidate strategies were developed and evaluated using a fast-time simulation consisting of a simple point-mass performance model of a transport-category airplane and an analytical microburst model. The results indicate that the recovery strategy characteristics that best utilize available airplane energy include an initial reduction in pitch attitude to reduce the climb rate, followed by an increase in pitch up to the stick shaker angle of attack. The stick shaker angle of attack should be reached just as the airplane is exiting the microburst. The shallowest angle of climb necessary for obstacle clearance should be used. If the altitude is higher than necessary, an intentional descent to reduce the airspeed deceleration should be used. Of the strategies tested, two flight-path-angle based strategies had the highest recovery altitudes and the least sensitivity to variations in the encounter scenarios.

Hinton, David A.↗
NASA NTRS1988

Helicopter main-rotor noise: Determination of source contributions using scaled model data

Acoustic data from a test of a 40 percent model MBB BO-105 helicopter main rotor are scaled to equivalent full-scale flyover cases. The test was conducted in the anechoic open test section of the German-Dutch Windtunnel (DNW). The measured data are in the form of acoustic pressure time histories and spectra from two out-of-flow microphones underneath and foward of the model. These are scaled to correspond to measurements made at locations 150 m below the flight path of a full-scale rotor. For the scaled data, a detailed analysis is given for the identification in the data of the noise contributions from different rotor noise sources. Key results include a component breakdown of the noise contributions, in terms of noise criteria calculations of a weighted sound pressure level (dBA) and perceived noise level (PNL), as functions of rotor advance ratio and descent angle. It is shown for the scaled rotor that, during descent, impulsive blade-vortex interaction (BVI) noise is the dominant contributor to the noise. In level flight and mild climb, broadband blade-turbulent wake interaction (BWI) noise is dominant due to the absence of BVI activity. At high climb angles, BWI is reduced and self-noise from blade boundary-layer turbulence becomes the most prominent.

Brooks, Thomas F.↗
NASA NTRS1987

HIDEC adaptive engine control system flight evaluation results

An integrated flight propulsion control mode, the Adaptive Engine Control System (ADECS), has been developed and flight tested on an F-15 aircraft as part of the NASA Highly Integrated Digital Electronic Control program. The ADECS system realizes additional engine thrust by increasing the engine pressure ratio (EPR) at intermediate and afterburning power, with the amount of EPR uptrim modulated using a predictor scheme for angle-of-attack and sideslip angle. Substantial improvement in aircraft and engine performance was demonstrated, with a 16 percent rate of climb increase, a 14 percent reduction in time to climb, and a 15 percent reduction in time to accelerate. Significant EPR uptrim capability was found with angles-of-attack up to 20 degrees.

Yonke, W. A.↗
NASA NTRS1988

Performance improvements of an F-15 airplane with an integrated engine-flight control system

An integrated flight and propulsion control system has been developed and flight demonstrated on the NASA Ames-Dryden F-15 research aircraft. The highly integrated digital control (HIDEC) system provides additional engine thrust by increasing engine pressure ratio (EPR) at intermediate and afterburning power. The amount of EPR uptrim is modulated based on airplane maneuver requirements, flight conditions, and engine information. Engine thrust was increased as much as 10.5 percent at subsonic flight conditions by uptrimming EPR. The additional thrust significantly improved aircraft performance. Rate of climb was increased 14 percent at 40,000 ft and the time to climb from 10,000 to 40,000 ft was reduced 13 percent. A 14 and 24 percent increase in acceleration was obtained at intermediate and maximum power, respectively. The HIDEC logic performed fault free. No engine anomalies were encountered for EPR increases up to 12 percent and for angles of attack and sideslip of 32 and 11 deg, respectively.

Myers, Lawrence P.↗
NASA NTRS1988

Trajectory optimization and guidance law development for national aerospace plane applications

The problem of onboard trajectory optimization for an airbreathing, single-stage-to-orbit vehicle is examined. A simple model representative of the aerospace plane concept, including a dual-mode propulsion system composed of scramjet and rocket engines, is presented. Consideration is restricted to hypersonic flight within the atmosphere. An energy state approximation is used in a four-state model for flight of a point mass in a vertical plane. Trajectory constraints, including those of dynamic pressure and aerodynamic heating, are initially ignored. Singular perturbation methods are applied in solving the optimal control problem of minimum fuel climb. The resulting reduced solution for the energy state dynamics provides an optimal altitude profile dependent on energy level and control for rocket thrust. A boundary-layer analysis produces an approximate lift control solution in feedback form and accounts for altitude and flight path angle dynamics. The reduced solution optimal climb path is presented for the unconstrained case and the case for which a maximum dynamic pressure constraint is enforced.

Calise, A. J.↗
NASA NTRS1988

Don/doff support stand for use with rear entry space suits

A don/doff support stand for use with rear entry space suits is disclosed. The support stand is designed for use in one-g environments; however, certain features of the stand can be used on future spacecraft, lunar, or planetary bases. The present invention has a retainer which receives a protrucing lug fixed on the torso section of the space suit. When the lug is locked in the retainer, the space suit is held in a generally upright position. In a one-g environment a portable ladder is positioned adjacent to the rear entry of the space suit supported by the stand. The astronaut climbs up the ladder and grasps a hand bar assembly positioned above the rear entry. The astronaut then slips his legs through the open rear entry and down into the abdominal portion of the suite. The astronaut then lowers himself fully into the suit. The portable ladder is then removed and the astronaut can close the rear entry door. The lug is then disengaged from the retainer and the astronaut is free to engage in training exercises in the suit. When suit use is over, the astronaut returns to the stand and inserts the lug into the retainer. A technician repositions the ladder. The astronaut opens the rear entry door, grasps the hand bar assembly and does a chin-up to extricate himself from the suit. The astronaut climbs down the movable ladder while the suit is supported by the stand.

Kosmo, Joseph J.↗
NASA NTRS1988

Comparisons of predicted and measured rotor performance in hover using a new free wake analysis

A new free-wake analysis has been developed to predict the performance of rotors in hover and axial flight. The analysis finds the rotor wake geometry using a novel influence coefficient/relaxation scheme. In this paper, the features of the analysis are reviewed, and the accuracy of the analysis is assessed for a wide range of rotor configurations in hover and vertical climb. The effects of variations in the analysis parameters are addressed, and recommendations for future development are presented. Generally good results were obtained for the predicted performance of a wide range of rotor geometries and operating conditions without any special 'tuning' of the analysis. The analysis also provides predictions of rotor performance in vertical climb that are substantially more accurate than momentum theory.

Felker, Fort F.↗
NASA NTRS1989

Optimal guidance and propulsion control for transatmospheric vehicles

Problems associated with on-board trajectory optimization and with the synthesis of guidance laws are addressed for ascent to LEO of an air-breathing, single-stage-to-orbit vehicle. A multimode propulsion system is assumed which incorporates turbojet, ramjet, scramjet, and rocket engines. An energy-state approximation is applied to a four-state dynamic model for flight of a point mass over a spherical nonrotating earth. An algorithm for generating fuel-optimal climb profiles is derived via singular perturbation theory. This algorithm results from application of the minimum principle to a low-order dynamic model that includes general functional dependence on angle of attack and a normal component of thrust. Switching conditions are derived which, under appropriate assumptions, govern optimal transition from one propulsion mode to another. The use of bank angle to modulate the magnitude of the vertical component of lift is shown to improve the index performance. Numerical results illustrate the nature of the resulting fuel-optimal climb paths.

Corban, J. E.↗
NASA NTRS1989

A real-time guidance algorithm for aerospace plane optimal ascent to low earth orbit

Problems of onboard trajectory optimization and synthesis of suitable guidance laws for ascent to low Earth orbit of an air-breathing, single-stage-to-orbit vehicle are addressed. A multimode propulsion system is assumed which incorporates turbojet, ramjet, Scramjet, and rocket engines. An algorithm for generating fuel-optimal climb profiles is presented. This algorithm results from the application of the minimum principle to a low-order dynamic model that includes angle-of-attack effects and the normal component of thrust. Maximum dynamic pressure and maximum aerodynamic heating rate constraints are considered. Switching conditions are derived which, under appropriate assumptions, govern optimal transition from one propulsion mode to another. A nonlinear transformation technique is employed to derived a feedback controller for tracking the computed trajectory. Numerical results illustrate the nature of the resulting fuel-optimal climb paths.

Calise, A. J.↗
NASA NTRS1990

Stress versus temperature dependent activation energies in creep

The activation energy for creep at low stresses and elevated temperatures is lattice diffusion, where the rate controlling mechanism for deformation is dislocation climb. At higher stresses and intermediate temperatures, the rate controlling mechanism changes from that of dislocation climb to one of obstacle-controlled dislocation glide. Along with this change, there occurs a change in the activation energy. It is shown that a temperature-dependent Gibbs free energy does a good job of correlating steady-state creep data, while a stress-dependent Gibbs free energy does a less desirable job of correlating the same data. Applications are made to copper and a LiF-22 mol. percent CaF2 hypereutectic salt.

Freed, A. D.↗
NASA NTRS1989

The SKY SHARK: an RPV Designed to Investigate the Pressure Distribution on a Lifting Surface

The objective was to design a remotely piloted vehicle which is capable of gathering in-flight pressure distribution data on a lifting test specimen, and then test the design by constructing a subscale demonstrator, to prove the flight worthiness of the concept. The technology demonstrator was scheduled for takeoff at approximately, 7:20 AM on Thursday April 27th. There was a light wind from the southeast. The plane was hand-launched and made an initial dip, most likely due to the poor trim conditions at launch. It then began to climb and bank into a left turn. The aircraft climbed to an altitude of approximately 150 ft and circled. The plane flew for several minutes and at times appeared to bump around, which was due to thermal activity disrupting the flight of the aircraft. The aircraft was brought slowly down in a power-off condition and glided in for a belly landing and landed without incident. Results of the flight test proved the general capability of the design to maintain flight stability throughout the take off, cruise, turning, and landing flight regimes. We were not able to demonstrate stability with the test specimen in place as the control surfaces designed to counteract the instabilities induced in the static system, winglets and ailerons, were not included.

Ziemba, Rob↗
NASA NTRS1990

Carrier aircraft

The Ohio State University planned to conduct a conceptual design of a single research vehicle that could be used to explore the flight regime from Mach 6 to Mach 12. Since this aircraft will be a special purpose vehicle, it need not take off and land in a conventional manner. Indeed, if this aircraft were launched from a larger aircraft that carried it to altitude, then conventional landing gear would not be needed and the extra weight of the fuel needed to take off and climb into the stratosphere would be eliminated. The focus of the students' project was on the design of a carrier aircraft answering to the specifications. Its mission is to take off with the research aircraft from runways of less than 15,000 feet, climb to 40,000 feet, and release the hypersonic aircraft at the speed of Mach 8, and return to base. The range of this mission is 2000 n.m. This study includes the conception of an optimized aircraft (geometry, weights, propulsion, aerodynamics, interactions between the two aircraft, etc.), the longitudinal stability of the composite, and the separation critical phase.

Source record↗
NASA NTRS1991

Icing characteristics of a natural-laminar-flow, a medium-speed, and a swept, medium-speed airfoil

Tests were conducted at the Icing Research Tunnel at the NASA Lewis Research Center to determine the icing characteristics of three modern airfoils, a natural laminar flow, a medium speed and a swept medium speed airfoil. Tests measured the impingement characteristics and drag degradation for angles of attack typifying cruise and climb for cloud conditions typifying the range that might be encountered in flight. The maximum degradation occurred for the cruise angle of attack for the long glaze ice condition for all three airfoils with increases over baseline drag being 486 percent, 510 percent, and 465 percent for the natural laminar flow, the medium speed and the swept medium speed airfoil respectively. For the climb angle of attack, the maximum drag degradation (and extent of impingement) observed were also for the long glaze ice condition, and were 261 percent, 181 percent and 331 percent respectively. The minimum drag degradation (and extent of impingement) occurred for the cruise condition and for the short, rime spray which increases over baseline drag values of 47 percent, 28 percent and 46 percent respectively.

Bidwell, Colin S.↗
NASA NTRS1990

Teamwork in high-risk environments analogous to space

Mountaineering expeditions combine a number of factors which make them potentially good analogs to the planetary exploration facet of long-duration space missions. A study of mountain climbing teams was conducted in order to evaluate the usefulness of the environment as a space analog and to specifically identify the factors and issues surrounding teamwork and 'successful' team performance in two mountaineering environments. This paper focuses on social/organizational factors, including team size and structure, leadership styles and authority structure which were found in the sample of 22 climb teams (122 individuals). The second major issue discussed is the construction of a valid performance measure in this high-risk environment.

Kanki, Barbara G.↗
NASA NTRS1991

Icing characteristics of a natural-laminar-flow, a medium-speed, and a swept, medium-speed airfoil

Tests were conducted in the Icing Research Tunnel at the NASA Lewis Research Center to determine the icing characteristics of three modern airfoils: a natural-laminar-flow, a medium-speed, and a swept medium-speed airfoil. The tests measured the impingement characteristics and drag degradation for angles-of-attack typifying cruise and climb for cloud conditions typifying the range that might be encountered in flight. The maximum degradation occurred at the cruise angle-of-attack for the long, glaze ice condition for all three airfoils with increases over baseline drag being 486 percent, 510 percent, and 465 percent for the natural-laminar-flow, the medium-speed, and the swept, medium-speed airfoils, respectively. For the climb angle-of-attack, the maximum drag degradation (and total extent of impingement) observed were also for the long, glaze ice condition and were 261 percent, 181 percent, and 331 percent, respectively. The minimum drag degradation (and extent of impingement) occurred for the cruise condition and for the short, rime spray with increases over baseline drag values being 47 percent, 28 percent, 46 percent, respectively.

Bidwell, Colin S.↗
NASA NTRS1989

Intelligent Network Management and Functional Cerebellum Synthesis

Transdisciplinary modeling of the cerebellum across histology, physiology, and network engineering provides preliminary results at three organization levels: input/output links to central nervous system networks; links between the six neuron populations in the cerebellum; and computation among the neurons of the populations. Older models probably underestimated the importance and role of climbing fiber input which seems to supply write as well as read signals, not just to Purkinje but also to basket and stellate neurons. The well-known mossy fiber-granule cell-Golgi cell system should also respond to inputs originating from climbing fibers. Corticonuclear microcomplexing might be aided by stellate and basket computation and associate processing. Technological and scientific implications of the proposed cerebellum model are discussed.

Loebner, Egon E.↗
NASA NTRS1991

Results from a test of a 2/3-scale V-22 rotor and wing in the 40- by 80-Foot Wind Tunnel

A test of a 0.658-scale V-22 rotor and wing was conducted in the 40- by 80-Foot Wind Tunnel at Ames Research Center. The principal objectives of the test were to measure the wing download in hover for a variety of test configurations, and rotor performance in forward flight. Also, a limited amount of data on rotor performance in vertical climb were acquired. This paper presents the results from the test with predictions from appropriate analytical methods. A new method for presenting and interpreting wing surface pressure data in hover is described, and this method shows that the wing flap can produce substantial lift loads in hover. The rotor performance in vertical climb was underpredicted by CAMRAD/JA and by the free wake analysis EHPIC. A simple momentum theory is presented which provides good predictions of rotor performance in forward flight.

Felker, Fort F.↗