Search NASA⌕ Search

SEARCH · Search NASA

Results for “component test capabilities”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

A New High-Speed Oil-Free Turbine Engine Rotordynamic Simulator Test Rig

A new test rig has been developed for simulating high-speed turbomachinery rotor systems using Oil-Free foil air bearing technology. Foil air bearings have been used in turbomachinery, primarily air cycle machines, for the past four decades to eliminate the need for oil lubrication. The goal of applying this bearing technology to other classes of turbomachinery has prompted the fabrication of this test rig. The facility gives bearing designers the capability to test potential bearing designs with shafts that simulate the rotating components of a target machine without the high cost of building "make-and-break" hardware. The data collected from this rig can be used to make design changes to the shaft and bearings in subsequent design iterations. This paper describes the new test rig and demonstrates its capabilities through the initial run with a simulated shaft system.

Howard, Samuel A.↗

Sensitivity of Precipitation to Parameter Values in the Community Atmosphere Model Version 5

One objective of the Climate Science for a Sustainable Energy Future (CSSEF) program is to develop the capability to thoroughly test and understand the uncertainties in the overall climate model and its components as they are being developed. The focus on uncertainties involves sensitivity analysis: the capability to determine which input parameters have a major influence on the output responses of interest. This report presents some initial sensitivity analysis results performed by Lawrence Livermore National Laboratory (LNNL), Sandia National Laboratories (SNL), and Pacific Northwest National Laboratory (PNNL). In the 2011-2012 timeframe, these laboratories worked in collaboration to perform sensitivity analyses of a set of CAM5, 2° runs, where the response metrics of interest were precipitation metrics. The three labs performed their sensitivity analysis (SA) studies separately and then compared results. Overall, the results were quite consistent with each other although the methods used were different. This exercise provided a robustness check of the global sensitivity analysis metrics and identified some strongly influential parameters.

54 ENVIRONMENTAL SCIENCES↗

Evaluating Storage Systems for Lustre

Storage systems are complex, including multiple subsystems and components. Sustained operations with top performance require all these subsystems and components working as expected. Having a detailed performance profile helps establishing a baseline. This baseline can be used for easier identification of possible future problems. A systematic bottom-to-top approach, starting with a detailed performance analysis of disks and moving up across layers and subsystems, provides a quantitative breakdown of each component's capabilities and bottlenecks. Coupling these low-level tests with Lustre-level evaluations will present a better understanding of performance expectations under different I/O workloads.

97 MATHEMATICS AND COMPUTING↗

An Analytical Tool for Fracture Control

The structural integrity of critical NASA space flight hardware is ensured through a damage tolerance program which is dictated in the fracture control requirements. The goal of a fracture control program is to ensure proper material selection and control, control of working stress levels, use of fracture resistant design concepts, manufacturing process control, and the use of qualified inspection procedures. The damage tolerance philosophy assumes that all components contain initial defects and the damage accumulation process is thus entirely crack propagation. The service capability of fracture critical components is determined by analysis and/or test. A large percentage of NASA fracture critical hardware is certified by analysis only and it is therefore imperative that the analysis code utilized contain the latest state of the art technology. Not all space contractors and vendors are able to develop and maintain an analysis code which meets this requirement. A response to this need has been fulfilled by the development of the NASA/FLAGRO (NASGRO) fracture mechanics code here at the Johnson Space Center. The NASGRO code is based primarily in Linear Elastic Fracture Mechanics (LEFM) and is continually updated to meet to needs of the user community. Development assistance comes from other NASA centers as well as the European Space Agency (ESA). The code currently has a vast materials data file (over 350 different entries) which defines the material strength, fracture toughness, crack growth rate, and crack growth threshold. The code also allows for user defined inputs of data from other sources. The code also provides a large library of stress intensity factor solutions for numerous geometries and loading conditions.

Patin, Raymond M.↗

Overview of the NASA Subsonic Rotary Wing Aeronautics Research Program in Rotorcraft Crashworthiness

This paper provides an overview of rotorcraft crashworthiness research being conducted at NASA Langley Research Center under sponsorship of the Subsonic Rotary Wing (SRW) Aeronautics Program. The research is focused in two areas: development of an externally deployable energy attenuating concept and improved prediction of rotorcraft crashworthiness. The deployable energy absorber (DEA) is a composite honeycomb structure, with a unique flexible hinge design that allows the honeycomb to be packaged and remain flat until needed for deployment. The capabilities of the DEA have been demonstrated through component crush tests and vertical drop tests of a retrofitted fuselage section onto different surfaces or terrain. The research on improved prediction of rotorcraft crashworthiness is focused in several areas including simulating occupant responses and injury risk assessment, predicting multi-terrain impact, and utilizing probabilistic analysis methods. A final task is to perform a system-integrated simulation of a full-scale helicopter crash test onto a rigid surface. A brief description of each research task is provided along with a summary of recent accomplishments.

Jackson, Karen E.↗

Overview of the NASA Subsonic Rotary Wing Aeronautics Research Program in Rotorcraft Crashworthiness

This paper provides an overview of rotorcraft crashworthiness research being conducted at NASA Langley Research Center under sponsorship of the Subsonic Rotary Wing (SRW) Aeronautics Program. The research is focused in two areas: development of an externally deployable energy attenuating concept and improved prediction of rotorcraft crashworthiness. The deployable energy absorber (DEA) is a composite honeycomb structure, with a unique flexible hinge design that allows the honeycomb to be packaged and remain flat until needed for deployment. The capabilities of the DEA have been demonstrated through component crush tests and vertical drop tests of a retrofitted fuselage section onto different surfaces or terrain. The research on improved prediction of rotorcraft crashworthiness is focused in several areas including simulating occupant responses and injury risk assessment, predicting multi-terrain impact, and utilizing probabilistic analysis methods. A final task is to perform a system-integrated simulation of a full-scale helicopter crash test onto a rigid surface. A brief description of each research task is provided along with a summary of recent accomplishments.

Jackson, Karen E.↗

Ground System Development at the Morehead State University for Interplanetary Smallsat Missions

As more small satellites are used for interplanetary research and exploration, more ground antennas with sufficiently large aperture are needed to support the increased demand in deep space communication. The 21-m ground antenna at the Morehead State University in Kentucky, United States is under development to upgrade its telemetry, tracking and command capability at X-band. The system architecture is based on a hybrid design that combines commercially available products with specialized equipment developed for the National Aeronautic and Aerospace Administration’s Deep Space Network. This architecture produces a low-cost and geographically diverse system, connecting elements at the Morehead State University and those of the DSN at the Jet Propulsion Laboratory in Pasadena, California. The architecture makes Morehead antenna appears as one of the DSN nodes, albeit with a different performance metrics due to difference in aperture size. Its operation is geared for automation, with automated data retrieval of information needed for configuring the ground station for spacecraft tracking. An incremental testing approach is used to verify system capabilities as various components are deployed into the system.

Kruth, Jeff↗

The Coulomb, exchange, and correlation components of the electron-electron repulsion in harmonium atoms

Highly accurate Coulomb, exchange, and correlation components of the electron-electron repulsion energies of the three-electron harmonium atoms in the {sup 2}P{sub −} and {sup 4}P{sub +} states are obtained for 19 values of the confinement strength ω ranging from 10{sup −3} to 10{sup 3}. The computed data are consistent with their ω → 0 and ω → ∞ asymptotics that are given by closed-form algebraic expressions. Robust approximants that accurately reproduce the actual values of the energy components while strictly conforming to these limits are constructed, opening an avenue to stringent tests capable of predicting the performance of electronic structure methods for systems with varying extents of the dynamical and nondynamical electron correlation. The values of the correlation components, paired with the computed 1-matrices are expected to be particularly useful in the context of benchmarking of approximate density matrix functionals.

74 ATOMIC AND MOLECULAR PHYSICS↗

Internet Protocol Over Telemetry Testing for Earth Science Capability Demo Summary

The development and flight tests described here focused on utilizing existing pulse code modulation (PCM) telemetry equipment to enable on-vehicle networks of instruments and computers to be a simple extension of the ground station network. This capability is envisioned as a necessary component of a global range that supports test and development of manned and unmanned airborne vehicles.

Franz, Russ↗

Comparison of Fault Detection Algorithms for Real-time Diagnosis in Large-Scale System

In this paper, we present a review of different real-time capable algorithms to detect and isolate component failures in large-scale systems in the presence of inaccurate test results. A sequence of imperfect test results (as a row vector of I's and O's) are available to the algorithms. In this case, the problem is to recover the uncorrupted test result vector and match it to one of the rows in the test dictionary, which in turn will isolate the faults. In order to recover the uncorrupted test result vector, one needs the accuracy of each test. That is, its detection and false alarm probabilities are required. In this problem, their true values are not known and, therefore, have to be estimated online. Other major aspects in this problem are the large-scale nature and the real-time capability requirement. Test dictionaries of sizes up to 1000 x 1000 are to be handled. That is, results from 1000 tests measuring the state of 1000 components are available. However, at any time, only 10-20% of the test results are available. Then, the objective becomes the real-time fault diagnosis using incomplete and inaccurate test results with online estimation of test accuracies. It should also be noted that the test accuracies can vary with time --- one needs a mechanism to update them after processing each test result vector. Using Qualtech's TEAMS-RT (system simulation and real-time diagnosis tool), we test the performances of 1) TEAMSAT's built-in diagnosis algorithm, 2) Hamming distance based diagnosis, 3) Maximum Likelihood based diagnosis, and 4) HidderMarkov Model based diagnosis.

Kirubarajan, Thiagalingam↗

High-Resistivity Measurement System for Spacecraft Dielectrics

- Volume resistivity is a key material property needed for assessing the risk of electrostatic discharge (ESD) due to spacecraft charging. We have developed a volume resistivity test system capable of measuring volume resistivity ≥1019 Ω·cm in vacuum and at cryogenic temperatures. Key components of this new setup include a custom test fixture and very low noise battery voltage supply.

Chave, Robert↗

Evaluation of an oil-debris monitoring device for use in helicopter transmissions

Experimental tests were performed on an OH-58A helicopter main-rotor transmission to evaluate an oil-debris monitoring device (ODMD). The tests were performed in the NASA 500-hp Helicopter Transmission Test Stand. Five endurance tests were run as part of a U.S. Navy/NASA/Army advanced lubricants program. The tests were run at 100 percent design speed, 117-percent design torque, and 121 C (250 F) oil inlet temperature. Each test lasted between 29 and 122 hr. The oils that were used conformed to MIL-L-23699 and DOD-L-85734 specifications. One test produced a massive sun-gear fatigue failure; another test produced a small spall on one sun-gear tooth; and a third test produced a catastrophic planet-bearing cage failure. The ODMD results were compared with oil spectroscopy results. The capability of the ODMD to detect transmission component failures was not demonstrated. Two of the five tests produced large amounts of debris. For these two tests, two separate ODMD sensors failed, possibly because of prolonged exposure to relatively high oil temperatures. One test produced a small amount of debris and was not detected by the ODMD or by oil spectroscopy. In general, the ODMD results matched the oil spectroscopy results. The ODMD results were extremely sensitive to oil temperature and flow rate.

Lewicki, David G.↗

NASA Glenn Research Center Support of the Advanced Stirling Radioisotope Generator Project

A high-efficiency radioisotope power system was being developed for long-duration NASA space science missions. The U.S. Department of Energy (DOE) managed a flight contract with Lockheed Martin Space Systems Company to build Advanced Stirling Radioisotope Generators (ASRGs), with support from NASA Glenn Research Center. DOE initiated termination of that contract in late 2013, primarily due to budget constraints. Sunpower, Inc., held two parallel contracts to produce Advanced Stirling Convertors (ASCs), one with Lockheed Martin to produce ASC-F flight units, and one with Glenn for the production of ASC-E3 engineering unit "pathfinders" that are built to the flight design. In support of those contracts, Glenn provided testing, materials expertise, Government-furnished equipment, inspection capabilities, and related data products to Lockheed Martin and Sunpower. The technical support included material evaluations, component tests, convertor characterization, and technology transfer. Material evaluations and component tests were performed on various ASC components in order to assess potential life-limiting mechanisms and provide data for reliability models. Convertor level tests were conducted to characterize performance under operating conditions that are representative of various mission conditions. Despite termination of the ASRG flight development contract, NASA continues to recognize the importance of high-efficiency ASC power conversion for Radioisotope Power Systems (RPS) and continues investment in the technology, including the continuation of the ASC-E3 contract. This paper describes key Government support for the ASRG project and future tests to be used to provide data for ongoing reliability assessments.

Technology Transfer↗

Better Engineering with Testbeds to Reduce Uncertainties in Simulations and Tests

Testbeds to Reduce Uncertainties in Simulations and Tests (TRUST) -- formerly Benchmark Extensible Tractable Testbed Engineering Resource (LA-UR-16-23828) -- are experiments, with accompanying models and simulations, that support engineering capability development by helping to identify weaknesses and address needs. Weapon systems, subassemblies, and components are often complex and difficult to test and analyze, resulting in low confidence and high uncertainties in experimental and simulated results. The complexities make it difficult to distinguish between inherent uncertainties and errors due to insufficient capabilities. TRUST will first use simplified geometries and materials such that testing, data collection, modeling and simulation can be accomplished with high confidence and low uncertainty. Modifications and combinations of simple and well characterized TRUST can then be used to increase complexity in order to reproduce relevant mechanics and identify weaknesses. The ultimate goal is to help improve capabilities and increase confidence by building TRUST. This document presents the motivation, concept, benefits and examples for TRUST.

42 ENGINEERING↗

Expanding the Capability of A Legacy Combustion Flametube to Test High Temperature Engine Materials in Relevant Environments

New materials and component designs are needed to advance gas turbine engine technology and provide the performance and efficiency needs for future applications. In order to advance these materials, testing in combustion environments is a critical step prior to engine testing. In this work, we detail the design and the fabrication of a materials test sector in a flametube combustor facility. The facility simulates a combustion environment similar to that experienced by components in gas turbine engines. The flow regime is characterized by a combination of high-temperature, high-velocity, high-heat flux, and high-velocity that components experience in gas turbine engines. Exposure of components in this facility allows for the study of combined environmental effects and the impact on both coating and substrate durability. The test facility may operate across a wide range of pressures from 275-400 psig (1,896-2,758 kPa) and an air flow rate of 5 lb/s (2.27 kg/s). While combustion gas temperature is expected in excess of 3,000°F (1,649°C), 900°F (482°C) cooling air may be supplied to the backside of components or test articles. The flametube combustor was previously used to evaluate fuel injectors and combustion products, and the new test configuration will also allow for materials exposure to complex, engine-like conditions. The interior of the Test Section was additively manufactured from GRCop-84 and cryogenically fit and brazed to a stainless steel 304 housing. The use of a copper liner minimizes welds and with active cooling, is expected to provide better durability over traditional hardware using stainless steel or Inconel with a ceramic liner. The Test Section has two opposing removable windows approximately 230 mm x 80 mm that can accommodate articles up to 85 mm tall. This modular design allows for custom platforms to hold coupons, panels, or airfoil shapes to be tested with minimal re-engineering or fabrication. The bolted joint and sealing remains consistent, so any new testing only needs to work within the existing design footprint. This paper will provide an overview of the facility capabilities, design considerations, as well as thermal and structural analysis of the hardware. Future testing of ceramic matrix composite (CMC) airfoils and advanced environmental barrier coatings (EBCs) will also be discussed.

Combustion↗

Development and demonstration of manufacturing processes for fabricating graphite/PMR-15 polyimide structural elements

The processing requirements for graphite/PMR-15 polyimide composites developed to demonstrate the structural integrity of polyimide composite structural elements at temperatures up to 589K (600 F) are described. Major tasks included: quality assurance development; materials and process development; specification verification; flat panel fabrication; stiffened panel fabrication; honeycomb panel fabrication; chopped fiber moldings; and demonstration component fabrication. Materials, processing, and quality assurance documents were prepared from experimentally derived data. Structural elements consisting of flat panels, corrugated stiffeners, I-beams, hat stiffeners, honeycomb panels, and chopped fiber moldings were made and tested. Property data from 219K (-65 F) to 589K (600 F) were obtained. All elements were made in a production environment. The size of each element was sufficient to insure production capability and structural component applicability. Problems associated with adhesive bonding, laminate and structural element analysis, material variability, and test methods were addressed.

Sheppard, C. H.↗

Subscale maturation of advanced reactor technologies (SMART): A path forward for nuclear thermal propulsion fuel and reactor development

Nuclear Thermal Propulsion (NTP) systems are actively being developed for future crewed missions to Mars. NTP systems excel in missions where both high thrust and high specific impulse are required, but modern NTP systems currently do not have a Technology Readiness Level (TRL) high enough for use in crewed space exploration. TRLs are used to demonstrate the level of rigor with which a component/system has been tested/demonstrated for its intended use. While space systems technology in general must be qualified as a unit, nuclear technology must be first demonstrated to meet qualification level requirements both at the fuel (component) level and the reactor (subsystem) level. Here, in this paper, historic NTP development programs are surveyed to identify a testing and development strategy that can be effectively implemented to allow for NTP reactor development. Based on this strategy, required facilities to enable such activities are identified. Current domestic experimental capabilities to support NTP qualification are limited to separate effects testing of individual components. Separate effects testing is found extensively in historic NTP development efforts but is not sufficient for full fuel and reactor qualification. Combined effects testing allows for an accurate assessment of fuel performance but is not achievable for NTP conditions in existing facilities. Assessment of historic development programs suggests that an intermediate, subscale test facility is necessary to advance NTP TRLs. A solution to meet this need is proposed, namely the Subscale Maturation of Advanced Reactor Technologies (SMART) facility. SMART will mitigate risk to NTP development by enabling performance and reactor physics demonstrations of NTP subsystems. A SMART facility could be built by modifying existing nuclear test facilities, which may potentially enable schedule and cost savings. To pursue reactor qualification beyond the subscale, a new ground test facility will be necessary. This ground test facility should be developed concurrently with SMART to allow for the facility to be operational in time for expedited NTP engine demonstration.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

NASA Lewis Research Center's combustor test facilities and capabilities

NASA Lewis Research Center (LeRC) presently accommodates a total of six combustor test facilities with unique capabilities. The facilities are used to evaluate combustor and afterburner concepts for future engine applications, and also to test the survivability and performance of innovative high temperature materials, new instrumentation, and engine components in a realistic jet engine environment. The facilities provide a variety of test section interfaces and lengths to allow for flametube, sector and component testing. The facilities can accommodate a wide range of operating conditions due to differing capabilities in the following areas: inlet air pressure, temperature, and flow; fuel flow rate, pressure, and fuel storage capacity; maximum combustion zone temperature; cooling water flow rate and pressure; types of exhaust - atmospheric or altitude; air heater supply pressure; and types of air heaters - vitiated or nonvitiated. All of the facilities have provisions for standard gas (emissions) analysis, and a few of the facilities are equipped with specialized gas analysis equipment, smoke and particle size measurement devices, and a variety of laser systems. This report will present some of the unique features of each of the high temperature/high pressure combustor test facilities at NASA LeRC.

Bianco, Jean↗