Search NASA⌕ Search

SEARCH · Search NASA

Results for “computational fluid dynamics simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

CFD Simulations of the Truncated IHF Semi-Elliptical Nozzle Flow: Convective Calibration Plate

This paper reports computational simulations of a high-enthalpy panel test facility at NASA Ames Research Center. The recently developed facility configuration uses a truncated version of an existing semi-elliptical nozzle in the 60-MW Interaction Heating Facility, and it provides testing capability for panel test articles as large as 43.2 cm x 43.2 cm (17 in x 17 in). A water-cooled calibration plate, which is attached to the semi-elliptical nozzle bottom surface and instrumented with twenty Gardon-gage heat flux calorimeters and twelve pressure gages, is used to characterize the convective heating environment over the panel test articles. The present analysis comprises computational fluid dynamics simulations of the nonequilibrium flowfield in the facility nozzle and test box, and the flowfields over panel test articles. Both laminar and turbulent simulations are performed, and the computational results are compared with the calibration plate measurements. Comparisons of computed and measured heat fluxes indicate that the boundary layer in the semi-elliptical nozzle is transitional at certain conditions (relatively higher arc-heater pressures or mass flow rates).

Arc-jets↗

CFD Simulations for Arc-Jet Panel Testing Capability Development Using Semi-Elliptical Nozzles

This paper reports computational simulations in support of arc-jet panel testing capability development using semi-elliptical nozzles in a high enthalpy arc-jet facility at NASA Ames Research Center. Two different semi-elliptical nozzle configurations are proposed for testing panel test articles. Computational fluid dynamics simulations are performed to provide estimates of achievable panel surface conditions and useful test area for each configuration. The present analysis comprises three-dimensional simulations of the nonequilibrium flowfields in the semi-elliptical nozzles, test box and flowfield over the panel test articles. Computations show that useful test areas for the proposed two nozzle options are 20.32 centimeters by 20.32 centimeters (8 inches by 8 inches) and 43.18 centimeters by 43.18 centimeters (17 inches by 17 inches). Estimated values of the maximum cold-wall heat flux and surface pressure are 155 watts per centimeters squared and 39 kilopascals for the smaller panel test option, and 44 watts per centimeters squared and 7 kilopascals for the larger panel test option. Other important properties of the predicted flowfields are presented, and factors that limit the useful test area in the semi-free jet test configuration are discussed.

TPS↗

CFD Simulations for Arc-Jet Panel Testing Capability Development Using Semi-Elliptical Nozzles

This paper reports computational simulations in support of arc-jet panel testing capability development using semi-elliptical nozzles in a high enthalpy arc-jet facility at NASA Ames Research Center. Two different semi-elliptical nozzle configurations are proposed for testing panel test articles. Computational fluid dynamics simulations are performed to provide estimates of achievable panel surface conditions and useful test area for each configuration. The present analysis comprises three-dimensional simulations of the nonequilibrium flowfields in the semi-elliptical nozzles, test box and flowfield over the panel test articles. Computations show that useful test areas for the proposed two nozzle options are 20.32 centimeters by 20.32 centimeters (8 inches by 8 inches) and 43.18 centimeters by 43.18 centimeters (17 inches by 17 inches). Estimated values of the maximum cold-wall heat flux and surface pressure are 155 watts per centimeters squared and 39 kilopascals for the smaller panel test option, and 44 watts per centimeters squared and 7 kilopascals for the larger panel test option. Other important properties of the predicted flowfields are presented, and factors that limit the useful test area in the semi-free jet test configuration are discussed.

CFD↗

Modeling Flow and Particle Deposition in a Spent Nuclear Fuel Assembly

CFD (Computational Fluid Dynamic) simulation of aerosol-laden natural convective flow and particle deposition in a spent fuel storage canister with 37 assemblies is currently computationally prohibitive. PWR (Pressurized Water Reactor) assemblies have up to 289 pins or tubes with several spacer grids to align the pins. Spacer grids with mixing vanes induce swirling during operation to increase heat transfer. Each spacer grid contains hundreds of small structures such as retaining clips, channel walls, and openings. The largest canisters store 37 PWR assemblies thus, there are numerous pins, tubes, and spacer grids for which the flow region between and around these structures needs to be determined along with the movement and deposition of aerosol particles. Because of the complicated geometry, modeling the intricate flow even for just one assembly is currently impractical. Nonetheless, we are developing techniques for a practical model to assess the natural aerosol particle deposition process in a canister in the event that a release occurs from one or more fuel pins. In the previous work it was demonstrated that CFD can model the flow through a PWR spacer grid with mixing vanes, including particle deposition, in a reasonable amount of time on a personal computer. In this work, the analysis is extended to include the bypass region between an assembly and the canister basket walls. It is shown that the flow velocity in the bypass region is about three times that of the interstitial region between the pins. The lengths before and after the spacer grid are also extended to determine when the flow becomes fully developed. In addition, the approach of computationally “stitching together” segments of an assembly is demonstrated with the plan to ultimately model a full assembly. The fraction of particles that are deposited in a segment with a spacer grid is determined as a function of particle size and flow velocity.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Simulation of a rapid compression machine for evaluation of ignition chemistry and soot formation using gasoline/ethanol blends

Due to the projected decline of demand for gasoline in light duty engines and the advent of ethanol as a green fuel, the use of gasoline/ethanol blend fuels in heavy duty applications are being investigated as they are projected to have lower cost and lower lifecycle green house gas (GHG) emissions. In heavy duty engines, the primary mode of combustion is mixing controlled combustion where wide range of mixture conditions (equivalence ratio) exist. Soot emissions of these fuels in richer conditions are not well understood. The goal of this research is to evaluate some commercially available soot modeling codes for the particulate matter emissions from gasoline/ethanol fuel blends, especially at fuel rich conditions. A Rapid Compression Machine (RCM) is modeled in a three-dimensional numerical simulation using CONVERGE computational software using a reduced chemical kinetic mechanism with SAGE chemistry solver and a RANS k-ϵturbulence model with a sector model including the creviced piston. The creviced piston is used in the experimental setup to reduce boundary layer effects and to maintain a homogeneous core in the reaction cylinder. Computational fluid dynamics simulations are conducted for different gasoline-ethanol fuel blends from E10 (10% ethanol v/v) to E100. The fuel blend is modeled as a surrogate mixture of toluene, iso-octane, n-heptane for gasoline content, and ethanol. The computational results were validated against experimental results using pressure measurements and laser extinction diagnostics. Different soot models are investigated to evaluate their capability of predicting the sooting tendencies of fuel blends, especially in richer conditions experienced during mixing-controlled combustion. The experimental combustion characteristics such as the ignition delay of different blends of fuel are reasonably well predicted. The Particulate Size Mimic (PSM) model accurately predicts the soot generation characteristics of the different fuels, but the Hiroyasu-NSC model falls short in this regard. For accurate prediction of soot with the PSM model, the thermodynamic conditions during combustion must be accurately modeled. While the current computational modeling tools can produce accurate results for the prediction of particulate matter emissions, there is much work to be done in improving our understanding of the underlying fundamental processes.

Energy & Fuels↗

Full-Envelope Aero-Propulsive Model Identification for Lift+Cruise Aircraft Using Computational Experiments

This paper describes a process utilizing computational fluid dynamics experiments to develop a reduced-order, integrated propulsion-airframe aerodynamic model for a lift+cruise electric vertical takeoff and landing (eVTOL) reference aircraft concept. eVTOL configurations exhibit aerodynamic characteristics of both fixed-wing and rotary-wing aircraft as well as complex phenomena, such as propulsion-airframe interactions. Consequently, conventional aircraft aerodynamic modeling strategies require modification when applied to these unique aircraft. A novel aero-propulsive modeling approach using design of experiments techniques and computational fluid dynamics simulations is postulated for modeling a lift+cruise aircraft configuration. Aero-propulsive models are developed throughout the operational flight envelope to enable continuous flight dynamics simulations from hover through forward flight. The model adequacy is assessed using validation data acquired separately from data used to identify the model and indicates that the models have sufficient predictive capability. Research findings are presented with a discussion of unique lift+cruise aircraft aerodynamic characteristics and practical strategies to inform future aero-propulsive modeling and simulation efforts for eVTOL aircraft.

lift+cruise↗

Toward predictive permeabilities: Experimental measurements and multiscale simulation of methanol transport in Nafion

A polymer membrane's permeability to solutes determines its suitability for various applications: a permeability value is essential for predicting performance in diverse contexts. Using aqueous methanol permeation through Nafion as an example, we describe a methodology for determining membrane permeability that accounts for boundary layer effects and the possibility of swelling. For the materials and apparatus used herein, analysis of a permeance measurement and computational fluid dynamics simulations show that the mass transfer boundary layer is on the order of ones to tens of microns. Additionally, the data are used to develop and validate a multiscale model describing solute permeation through a hydrated membrane as a series of physical mechanistic steps: reversible adsorption from solution at the membrane interface, diffusion driven by a concentration gradient within the membrane, and reversible desorption into solution at the opposite membrane interface. The validated model is used to predict methanol transport across a solar-driven CO 2 reduction device and to assess the impact of polymer changes on the measured value. The approach of combining experimental data, computational fluid dynamics, and the mechanistic multiscale model is expected to provide more accurate analysis of membrane permeation data in cases with polymer swelling or unusual device geometries, among others.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Use of CFD in the Design of the 10- by 10-Foot Supersonic Wind Tunnel Characterization Array

At the 10- by 10-Foot Supersonic Wind Tunnel at the NASA Glenn Research Center, a future full test section characterization generated an ideal opportunity to design and build new characterization hardware to improve the understanding of the flow field, including flow quality, uniformity, and uncertainty in primary variables of interest. An array of flow sensing probes, referred to as the Characterization Array, was designed and built to replace 1960’s-era test section characterization hardware. Many references exist to guide wind tunnel characterization practitioners in the design of new hardware to properly measure various aspects of the flow within their wind tunnel facilities. Although reliable sources of information, these references tend to be over 30 years old and are not exhaustive. In scenarios where design decisions needed to be validated, computational simulations of the flow field around the characterization hardware were used. Decisions regarding probe location, probe spacing, and performance of various probes were justified using computational fluid dynamic simulations and rules-of-thumb from the legacy resources available in literature. This paper is intended to serve as an example of the benefits from integrating CFD into the design of wind tunnel hardware, particularly hardware for wind tunnel characterization.

CFD↗

Use of CFD in the Design of the 10- by 10-Foot Supersonic Wind Tunnel Characterization Array

At the 10- by 10-Foot Supersonic Wind Tunnel at the NASA Glenn Research Center, a future full test section characterization generated an ideal opportunity to design and build new characterization hardware to improve the understanding of the flow field, including flow quality, uniformity, and uncertainty in primary variables of interest. An array of flow sensing probes, referred to as the Characterization Array, was designed and built to replace 1960’s-era test section characterization hardware. Many references exist to guide wind tunnel characterization practitioners in the design of new hardware to properly measure various aspects of the flow within their wind tunnel facilities. Although reliable sources of information, these references tend to be over 30 years old and are not exhaustive. In scenarios where design decisions needed to be validated, computational simulations of the flow field around the characterization hardware were used. Decisions regarding probe location, probe spacing, and performance of various probes were justified using computational fluid dynamic simulations and rules-of-thumb from the legacy resources available in literature. This paper is intended to serve as an example of the benefits from integrating CFD into the design of wind tunnel hardware, particularly hardware for wind tunnel characterization.

CFD↗

Runtime volume visualization for parallel CFD

This paper discusses some aspects of design of a data distributed, massively parallel volume rendering library for runtime visualization of parallel computational fluid dynamics simulations in a message-passing environment. Unlike the traditional scheme in which visualization is a postprocessing step, the rendering is done in place on each node processor. Computational scientists who run large-scale simulations on a massively parallel computer can thus perform interactive monitoring of their simulations. The current library provides an interface to handle volume data on rectilinear grids. The same design principles can be generalized to handle other types of grids. For demonstration, we run a parallel Navier-Stokes solver making use of this rendering library on the Intel Paragon XP/S. The interactive visual response achieved is found to be very useful. Performance studies show that the parallel rendering process is scalable with the size of the simulation as well as with the parallel computer.

Ma, Kwan-Liu↗

Validation of Cryogenic Propellant Tank Self-Pressurization

NASA's near-future long-term space missions necessitate advancements in cryogenic fluid management (CFM), which includes safe and reliable long-term propellant storage. Consequently, NASA STMD (Space Technology Mission Directorate) has established the CFM Portfolio Project to improve CFM technologies for upcoming missions. As a part of CFM Modeling Portfolio, NASA Marshall Space Flight Center's (MSFC) Fluid Dynamics branch within the Propulsion Systems Department is tasked with assessing and improving computational tools used to support flight projects such as Human Lander System and Commercial Lunar Payload Services. One of the challenging modeling problems is that of self-pressurization of propellant tank due to heat leakage over long time periods. Reduced order and nodal tools find it extremely difficult to accurately predict self-pressurization under transient conditions or where complex flow patterns or thermal gradients exist, and application of 3-D CFD (computational fluid dynamics) simulations is necessary to characterize these problems. Until recently, CFD simulations for these long-term processes (order of hours or days) have been too impractical to conduct due to prohibitive wall time and computational resource requirements. The requisite CFD tool need to be efficient, computationally scalable, modular with ability to incorporate various physics models, and robust enough to not accumulate conservation errors over several hours of simulated time. NASA MSFC's Loci-Stream CFD tool along with the VOF module is a great candidate to fit this mold. In this paper, we validate Loci-Stream for predicting self-pressurization of a flight scale propellant tank so it can serve as a reliable design and analysis tool for NASA's CFM application needs. Liquid hydrogen tank pressurization tests carried out at the K-site testing facility provide a reliable data set for this purpose. These tests were simulated using Loci-Stream solver with VOF module as well as a hybrid approach which uses a lumped model for the ullage gas domain and CFD simulation of the liquid propellant. Both are shown to have very good predictive capabilities over multiple K-site experiments.

cryogenic fluid management↗

A Random Walk Model for Biomass Particle Mixing in Bubbling Fluidized Beds

We propose a physically motivated random walk model to describe the spatial and temporal mixing of a single biomass particle in a bubbling fluidized bed. The model parameters are estimated from measurements of a magnetically tagged simulated biomass particle in a laboratory fluidized bed. We demonstrate that Monte Carlo simulations using the model match key statistical features of the observed behavior reasonably well. These results suggest that a model of this type can simulate the effects of biomass particle mixing in biomass conversion reactors. We suggest possible improvements to the random walk model and propose how it might be used in conjunction with computational fluid dynamics simulations.

09 BIOMASS FUELS↗

WEC3: Wave Energy Converter Code Comparison Project: Preprint

This paper describes the recently launched Wave Energy Converter Code Comparison (WEC3) project and present preliminary results from this effort. The objectives of WEC3 are to verify and validate numerical modelling tools that have been developed specifically to simulate wave energy conversion devices and to inform the upcoming IEA OES Annex VI Ocean Energy Modelling Verification and Validation project. WEC3 is divided into two phases. Phase 1 consists of a code-to-code verification and Phase II entails code-to-experiment validation. WEC3 focuses on mid-fidelity codes that simulate WECs using time-domain multibody dynamics methods to model device motions and hydrodynamic coefficients to model hydrodynamic forces. Consequently, high-fidelity numerical modelling tools, such as Navier-Stokes computational fluid dynamics simulation, and simple frequency domain modelling tools were not included in the WEC3 project.

16 TIDAL AND WAVE POWER↗

High-Fidelity Simulations of HyMETS Arc-Jet Flows for PICA-N Modeling

Arc-jet testing is a fundamental tool in the screening of thermal protection systems under atmospheric entry conditions. In this work, high-fidelity computational fluid dynamics simulations coupled with machine learning methods for the Hypersonic Materials Environmental Test System arc-jet facility have been carried out. This effort improves the MEDLI-2 data reconstruction fidelity by understanding the impact of the NuSil coating over the PICA thermocouple plugs. Thermochemical non-equilibrium models are employed to simulate the flows inside the arc-jet nozzle and chamber and machine learning techniques are used to calibrate the arc-jet inflow conditions. The material response is simulated with the recession and in-depth numerical results compared to experimental measurements.

STMD↗

Experimental and Computational Analysis of a Rotating Detonation Combustor

Rotating detonation combustor (RDC) research has progressed along parallel experimental and computational paths with limited opportunities for validation. Validation is a crucial step to ensure RDC simulations provide an accurate representation of the physical phenomena, and thus, can be used with confidence for design optimization in different applications. In this study, data from a quasi-two-dimensional computational fluid dynamic simulation in an annular RDC are compared with experimental measurements including particle image velocimetry at 100 kHz. Results show good agreement between measured and simulated dynamic pressures, Chapman-Jouguet speeds, and static pressure distributions. Velocity measurements at the annulus exit show good temporal and quantitative agreement with simulations including spikes from the passing shock.

Detonation↗

Validation of Cryogenic Propellant Tank Self-Pressurization

NASA’s near-future long-term space missions necessitate advancements in cryogenic fluid management (CFM), which includes safe and reliable long-term propellant storage. Consequently, NASA STMD (Space Technology Mission Directorate) has established the CFM Portfolio Project to improve CFM technologies for upcoming missions. As a part of CFM Modeling Portfolio, NASA Marshall Space Flight Center’s (MSFC) Fluid Dynamics branch within the Propulsion Systems Department is tasked with assessing and improving computational tools used to support flight projects such as Human Lander System and Commercial Lunar Payload Services. One of the challenging modeling problems is that of self-pressurization of propellant tank due to heat leakage over long time periods. Reduced order and nodal tools find it extremely difficult to accurately predict self-pressurization under transient conditions or where complex flow patterns or thermal gradients exist, and application of 3-D CFD (computational fluid dynamics) simulations is necessary to characterize these problems. Until recently, CFD simulations for these long-term processes (order of hours or days) have been too impractical to conduct due to prohibitive wall time and computational resource requirements. The requisite CFD tool need to be efficient, computationally scalable, modular with ability to incorporate various physics models, and robust enough to not accumulate conservation errors over several hours of simulated time. NASA MSFC’s Loci-Stream CFD tool along with the VOF module is a great candidate to fit this mold. In this paper, we validate Loci-Stream for predicting self-pressurization of a flight scale propellant tank so it can serve as a reliable design and analysis tool for NASA’s CFM application needs. Liquid hydrogen tank pressurization tests carried out at the K-site testing facility provide a reliable data set for this purpose. These tests were simulated using Loci-Stream solver with VOF module as well as a hybrid approach which uses a lumped model for the ullage gas domain and CFD simulation of the liquid propellant. Both are shown to have very good predictive capabilities over multiple K-site experiments.

Hong Q. Yang↗

Impact of particle loading and phase coupling on gas–solid flow dynamics: A case study of a two-phase, gas–solid flow in an annular pipe

The present study is devoted to a two-phase, gas–solid flow in an annular pipe (hollow cylinder) at an elevated pressure of 15 bars and moderate Reynolds number of circa 6000. The influence of the particle loading, the interaction between the phases, and turbulence dispersion on the flow dynamics is systematically studied by means of computational fluid dynamics simulations, employing the Ansys FLUENT commercial package. The cases with a particle volumetric fraction of 1.2% are referred to as “high particle loading,” and those with 0.13% are denoted as “low particle loading.” The following cases are investigated: (1) pure gas flow; (2) low particle loading two-phase flow with one-way coupling and with turbulence dispersion; (3) low particle loading two-phase flow with two-way coupling but without turbulence dispersion; (4) low particle loading two-phase flow with two-way coupling and with turbulence dispersion; (5) high particle loading two-phase flow with one-way coupling and with turbulence dispersion; (6) high particle loading two-phase flow with two-way coupling but without turbulence dispersion; and (7) high particle loading two-phase flow with two-way coupling and with turbulence dispersion. Additionally, the boundary layer is found to grow without fluctuations of the turbulent kinetic energy (TKE) for cases 1, 2, and 5. For case 4, the TKE fluctuations have been identified, although they appear to be less substantial than those in cases 6 and 7. The authors attribute the semi-chaotic nature of the TKE fluctuations to the particle loading and two-way coupling. In addition, the onset and development of the flow instability have been observed at a random axial distance in cases 4, 6, and 7. Such instability is also attributed to the two-way coupling with turbulence dispersion in the flow. It is concluded that the particle loading, one-way, or two-way coupling between the phases, and the turbulence dispersion models significantly influence the development of the flow dynamics with the same inlet and boundary conditions. Consequently, it is not a trivial question, which result a user should trust. The present computational results inspire to perform verification as well as experimental validation of the simulations, so the simulation results can subsequently be used with confidence for design analysis.

42 ENGINEERING↗

Development of machine learning framework for interface force closures based on bubble tracking data

Interfacial force closures in the two-fluid model play a critical role for the predictive capabilities of void fraction distribution. However, the practices of interfacial force modeling have long been challenged by the inherent physical complexity of the two-phase flows. The rapidly expanding computational capabilities in the recent years have made high-fidelity data from the interface-captured direct numerical simulation become more available, and hence potential for data-driven interfacial force modeling has prevailed. In this work, we established a data-driven modeling framework integrated to the HZDR multiphase Eulerian-Eulerian framework for computational fluid dynamics simulations. The data-driven framework is verified in a benchmark problem, where a feedforward neural network managed to capture the non-linear mapping between bubble Reynolds number and drag coefficient and reproduce the void distribution resulting from the baseline model in the test case. The second focus is on utilizing the bubble tracking data set to form a closure for the bubble drag in the turbulent bubbly flow, in which the drag coefficient is set to be correlated with the bubble Reynolds number and the Eötvös number. Pseudo-steady state filtering in the Frenet Frame was carried out to obtain the drag coefficient from the turbulent bubbly flow data. The performance of the data-driven drag model is also examined through a case study, where improvement of model’s prediction near-wall is regarded necessary. In conclusion, discussion and further plans of investigation are provided.

42 ENGINEERING↗