Search NASA⌕ Search

SEARCH · Search NASA

Results for “copper surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Methane heat transfer investigation

Future high chamber pressure LOX/hydrocarbon booster engines require copper base alloy main combustion chamber coolant channels similar to the SSME to provide adequate cooling and reusable engine life. Therefore, it is of vital importance to evaluate the heat transfer characteristics and coking thresholds for LNG (94% methane) cooling, with a copper base alloy material adjacent to he fuel coolant. High pressure methane cooling and coking characteristics recently evaluated at Rocketdyne using stainless steel heated tubes at methane bulk temperatures and coolant wall temperatures typical of advanced engine operation except at lower heat fluxes as limited by the tube material. As expected, there was no coking observed. However, coking evaluations need be conducted with a copper base surface exposed to the methane coolant at higher heat fluxes approaching those of future high chamber pressure engines.

Source record↗
NASA NTRS1984

Deposit formation and heat transfer in hydrocarbon rocket fuels

An experimental research program was undertaken to investigate the thermal stability and heat transfer characteristics of several hydrocarbon fuels under conditions that simulate high-pressure, rocket engine cooling systems. The rates of carbon deposition in heated copper and nickel-plated copper tubes were determined for RP-1, propane, and natural gas using a continuous flow test apparatus which permitted independent variation and evaluation of the effect on deposit formation of wall temperature, fuel pressure, and fuel velocity. In addition, the effects of fuel additives and contaminants, cryogenic fuel temperatures, and extended duration testing with intermittent operation were examined. Corrosion of the copper tube surface was detected for all fuels tested; however, plating the insides of the tubes with nickel reduced deposit formation and eliminated corrosion in most cases. The lowest rates of carbon deposition were obtained for natural gas, and the highest rates were obtained for propane. Forced-convection heat transfer film coefficients were satisfactorily correlated using a Nusselt-Reynolds-Prandtl number equation for all the fuels tested.

Giovanetti, A. J.↗
NASA NTRS1982

New component development for multi-100 kW low-cost solar array applications

Studies of the cost and performance of flexible arrays have shown that the most dramatic reductions in the $/Watt figure of merit are achieved by increasing performance. An examination of those properties that contribute to array performance indicated areas where radical changes in current design practice and philosophy would result in significant cost and performance impacts. To take advantage of the predicted cost reductions, modules were fabricated and tested that had ultra-thin superstrates as a load carrying member and large area dielectric wraparound (DWA), gridded back surface and copper contacted solar cells.

Pack, G. J.↗
NASA NTRS1984

Methane heat transfer investigation

Future high chamber pressure LOX/hydrocarbon booster engines require copper-base alloy main combustion chamber coolant channels similar to the SSME to provide adequate cooling and resuable engine life. Therefore, it is of vital importance to evaluate the heat transfer characteristics and coking thresholds for LNG (94% methane) cooling, with a copper-base alloy material adjacent to the fuel coolant. High-pressure methane cooling and coking characteristics were recently evaluated using stainless-steel heated tubes at methane bulk temperatures and coolant wall temperatures typical of advanced engine operation except at lower heat fluxes as limited by the tube material. As expected, there was no coking observed. However, coking evaluations need be conducted with a copper-base surface exposed to the methane coolant at higher heat fluxes approaching those of future high chamber pressure engines.

Cook, R. T.↗
NASA NTRS1987

Traveling-wave-tube efficiency improvement by a low-cost technique for deposition of carbon on multistage depressed collector

A simple method of improving the traveling-wave-tube (TWT) and multistage depressed collector (MDC) efficiency has been demonstrated. The efficiency improvement was produced by the application of a thin layer of carbon to the copper electrodes of the MDC by means of a rapid, low-cost technique involving the pyrolysis of hydrocarbon oil in electric arc discharges. Experimental results with a representative TWT and MDC showed an 11 percent improvement in both the TWT and MDC efficiencies as compared to those of the same TWT and MDC efficiencies with bare copper electrode surfaces. An extended test with a 500-W, continuous wave (CW) TWT and small-sized MDC indicated good stability of the carbon coated electrode surfaces after a relatively small initial degradation in TWT overall and apparent MDC efficiencies.

Ebihara, Ben T.↗
NASA NTRS1987

TWT efficiency improvement by a low-cost technique for deposition of carbon on MDC electrodes

A simple method of improving the TWT and multistage depressed collector (MDC) efficiency has been demonstrated. The efficiency improvement was produced by the application of a thin layer of carbon to the copper electrodes of the MDC by means of a rapid low-cost technique involving the pyrolysis of hydrocarbon oil in electric arc discharges. Experimental results with a representative TWT and MDC showed an 11 percent improvement in both the TWT and MDC efficiencies as compared to those of the same TWT and MDC with machined copper electrode surfaces. An extended test with a 550-W CW TWT indicated good durability of the carbon-coated electrode surfaces.

Ebihara, Ben T.↗
NASA NTRS1991

Creep behavior of copper at intermediate temperatures. II - Surface microstructural observations. III - A comparison with theory

Three different types of microstructural slip features are noted to occur during the creep of Cu at 0.46-0.72 of absolute melting point. While single slip is associated with higher temperatures and lower stresses, complex wavy slip features are observed at higher temperatures and higher stresses as well as with increasing strains: suggesting the importance of cross-slip mechanisms. At lower temperatures and higher stresses the multiple-slip morphologies observed indicate that cross-slip mechanisms may control the creep of polycrystalline Cu only over a limited stress and temperature range. A phenomenological model is proposed which assumes that (1) cell boundaries within subgrains act as both sources of, and obstacles to, gliding dislocations, and (2) dislocation annihilation occurs at the cell boundaries by climb and cross-slip.

Raj, S. V.↗
NASA NTRS1992

Lightweight bipolar storage battery

An apparatus [10] is disclosed for a lightweight bipolar battery of the end-plate cell stack design. Current flow through a bipolar cell stack [12] is collected by a pair of copper end-plates [16a,16b] and transferred edgewise out of the battery by a pair of lightweight, low resistance copper terminals [28a,28b]. The copper terminals parallel the surface of a corresponding copper end-plate [16a,16b] to maximize battery throughput. The bipolar cell stack [12], copper end-plates [16a,16b] and copper terminals [28a,28b] are rigidly sandwiched between a pair of nonconductive rigid end-plates [20] having a lightweight fiber honeycomb core which eliminates distortion of individual plates within the bipolar cell stack due to internal pressures. Insulating foam [30] is injected into the fiber honeycomb core to reduce heat transfer into and out of the bipolar cell stack and to maintain uniform cell performance. A sealed battery enclosure [ 22] exposes a pair of terminal ends [26a,26b] for connection with an external circuit.

Rowlette, John J.↗
NASA NTRS2010

Improved Cloud Condensation Nucleus Spectrometer

An improved thermal-gradient cloud condensation nucleus spectrometer (CCNS) has been designed to provide several enhancements over prior thermal- gradient counters, including fast response and high-sensitivity detection covering a wide range of supersaturations. CCNSs are used in laboratory research on the relationships among aerosols, supersaturation of air, and the formation of clouds. The operational characteristics of prior counters are such that it takes long times to determine aerosol critical supersaturations. Hence, there is a need for a CCNS capable of rapid scanning through a wide range of supersaturations. The present improved CCNS satisfies this need. The improved thermal-gradient CCNS (see Figure 1) incorporates the following notable features: a) The main chamber is bounded on the top and bottom by parallel thick copper plates, which are joined by a thermally conductive vertical wall on one side and a thermally nonconductive wall on the opposite side. b) To establish a temperature gradient needed to establish a supersaturation gradient, water at two different regulated temperatures is pumped through tubes along the edges of the copper plates at the thermally-nonconductive-wall side. Figure 2 presents an example of temperature and supersaturation gradients for one combination of regulated temperatures at the thermally-nonconductive-wall edges of the copper plates. c) To enable measurement of the temperature gradient, ten thermocouples are cemented to the external surfaces of the copper plates (five on the top plate and five on the bottom plate), spaced at equal intervals along the width axis of the main chamber near the outlet end. d) Pieces of filter paper or cotton felt are cemented onto the interior surfaces of the copper plates and, prior to each experimental run, are saturated with water to establish a supersaturation field inside the main chamber. e) A flow of monodisperse aerosol and a dilution flow of humid air are introduced into the main chamber at the inlet end. The inlet assembly is designed to offer improved (relative to prior such assemblies) laminar-flow performance within the main chamber. Dry aerosols are subjected to activation and growth in the supersaturation field. f) After aerosol activation, at the outlet end of the main chamber, a polished stainless-steel probe is used to sample droplets into a laser particle counter. The probe features an improved design for efficient sampling. The counter has six channels with size bins in the range of 0.5- to 5.0-micron diameter. g) To enable efficient sampling, the probe is scanned along the width axis of the main chamber (thereby effecting scanning along the temperature gradient and thereby, further, effecting scanning along the supersaturation gradient) by means of a computer-controlled translation stage.

Leu, Ming-Taun↗
DOE OSTI2024

Fabrication of 3D-printed copper based zinc anodes

The production of a porous copper-zinc structure includes providing copper ink, creating a 3D model of the porous copper-zinc structure, 3D printing the copper ink into a porous copper lattice structure using the 3D model, heat treatment of the porous copper lattice structure producing a heat treated porous copper lattice structure, surface modification of the heat treated porous copper lattice structure by nanowires growth on the heat treated porous copper lattice structure producing a heat treated porous copper lattice structure with nanowires, and electrodeposition of zinc onto the heat treated porous copper lattice structure with nanowires to produce the porous copper-zinc structure.

Zhu, Cheng↗
NASA NTRS1978

Energy distributions of sputtered copper neutrals and ions

Direct quantitative analysis of surfaces by secondary ion mass spectrometry will depend on an understanding of the yield ratio of ions to neutrals. This ratio as a function of the energy of the sputtered particles has been obtained for a clean polycrystalline copper surface sputtered by 1000-3000 eV Ar(+). The energy distributions of both neutral and ionized copper were measured with a retarding potential analyzer using potential modulation differentiation and signal averaging. The maximum for both distributions is identical and occurs near 2.5 eV. The energy distributions of neutrals is more sharply peaked than that of the ions, presumably as a consequence of more efficient nutralization of slow escaping ions by the mobile electrons of copper. The ion-neutral ratio is compared with results from various ionization models.

Lundquist, T. R.↗
NASA NTRS2005

Spray Cooling Trajectory Angle Impact Upon Heat Flux Using a Straight Finned Enhanced Surface

Experiments were conducted to study the effects of spray trajectory angles upon heat flux for flat and enhanced surface spray cooling. The surface enhancement consisted of straight fins machined on the top surface of a copper heater block. Spray cooling curves were obtained with the straight fin surface aligned both parallel (axial) and perpendicular (transverse) to the spray axis. Measurements were also obtained on a flat surface heater block for comparison purposes. Each copper block had a cross-sectional area of 2.0 sq cm. A 2x2 nozzle array was used with PF-5060 as the working fluid. Thermal performance data was obtained under nominally degassed (chamber pressure of 41.4 kPa) conditions. Results show that the maximum CHF in all cases was attained for a trajectory angle of 30' from the surface normal. Furthermore, trajectory angles applied to straight finned surfaces can have a critical heat flux (CHF) enhancement as much as 75% (heat flux value of 140 W/sq cm) relative to the vertical spray orientation for the analogous flat surface case under nominally degassed conditions.

Silk, Eric A.↗
NASA NTRS1978

Shear strength of metal - SiO2 contacts

The strength of the bond between metals and SiO2 was studied by measuring the static coefficient of friction of metals contacting alpha-quartz in ultrahigh vacuum. It was found that copper with either chemisorbed oxygen, nitrogen, or sulphur exhibited higher contact strength on stoichiometric SiO2 than did clean copper. Since the surface density of states induced by these species on copper is similar, it appears that the strength of the interfacial bond can be related to the density of states on the metal surface.

Pepper, S. V.↗
NASA NTRS1978

Shear strength of metal - SiO2 contacts

The strength of the bond between metals and SiO2 is studied by measuring the static coefficient of friction of metals contacting alpha-quartz in ultrahigh vacuum. It was found that copper with either chemisorbed oxygen, nitrogen or sulphur exhibited higher contact strength on stoichiometric SiO2 than did clean copper. Since the surface density of states induced by these species on copper is similar, it appears that the strength of the interfacial bond can be related to the density of states on the metal surface.

Pepper, S. V.↗
DOE OSTI2022

Effect of amine type on acidic toxic gas adsorption at ambient conditions on modified CuBTC

We report two amine-modified copper-based Metal Organic Frameworks (MOF (CuBTC)) of different surface chemical and textural features were synthesized and used as adsorbents of acidic toxic gases (NO 2 and H 2 S) in both moist (71% relative humidity (R.H.)) and dry conditions. The initial and exhausted samples were characterized by nitrogen adsorption, powder X-ray diffraction, scanning electron microscopy, thermal gravimetric analysis and Fourier transform infrared spectroscopy. The addition of melamine prevented full growth of CuBTC crystals and resulted in amorphous-like particles with sizes less than 200 nm. The material was non-porous with a small surface area. When urea was used as an amine source, the resulting particles maintained the overall octahedral shape of the parent CuBTC MOF and the material was more porous than the parent MOF. While the urea-modified CuBTC sample performed well as an NO 2 adsorbent in the presence of moisture, the reactivity of the melamine-modified sample and its physical properties provided a favorable environment for the removal of H 2 S. The incorporation of amines into the MOF structure also resulted in surface defects /open copper sites that favored the removal of toxic gases in dry conditions. The reactivity of the adsorbents with toxic gases was demonstrated by the changes in the adsorbent colors, in texture, and in surface chemistry (organic salts, complexes, sulfides and nitrates were formed).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Density Functional Theory Study of the Adsorption and Dissociation of Copper(I) Acetamidinates on Ni(110): The Effect of the Substrate

In order to assess the role of a metal substrates on the thermal chemistry of adsorbed acetamidinate metalorganic compounds, we have studied the surface chemistry of copper(I)–N,N'-dimethylacetamidinate on Ni(110) using density functional theory and contrasted it with similar calculations we previously carried out on Cu(110). At low coverages, it was found that, in its most stable configuration, the molecular adsorption of copper(I)–N,N'-dimethylacetamidinate dimers occurs with the Cu atoms occupying surface hollow sites. In this work, the ligands reorient away from those metal centers, and the N atoms develop new direct bonds with surface Ni atoms. However, this configuration is not stable and decomposes by losing both ligands to the surface. In the final state, the two ligands bind via their N atoms to Ni sites one lattice space away from the sites where the Cu atoms remain, with their molecular planes perpendicular to that of the surface. This is in contrast with what happens in the case of adsorption on Cu(110), where the Cu atoms from the metalorganic complex still occupy hollow sites but where only one of the ligands breaks away and binds directly to the surface; the other remains on top of the two Cu ions. In terms of the energetics of adsorption and decomposition, the reactions on Ni(110) are much more exothermic than on Cu(110). Further analysis of the distribution of charge within the adsorbates shows a minor reduction of the Cu atoms of the dimer upon interaction with the surface; full reduction to metallic copper is complete only when both ligands have fully migrated to their new Ni surface sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1967

High-strength braze joints between copper and steel

High-strength braze joints between copper and steel are produced by plating the faying surface of the copper with a layer of gold. This reduces porosity in the braze area and strengthens the resultant joint.

Kuhn, R. F.↗