Search NASA⌕ Search

SEARCH · Search NASA

Results for “delay line”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Wire transfer of charge packets using a CCD-BBD structure for charge-domain signal processing

A structure for the virtual transfer of charge packets across metal wires is described theoretically and is experimentally verified. The structure is a hybrid of charge-coupled device (CCD) and bucket-brigade device (BBD) elements and permits the topological crossing of charge-domain signals in low power signal processing circuits. A test vehicle consisting of 8-, 32-, and 96-stage delay lines of various geometries implemented in a double-poly, double-metal foundry process is used to characterize the wire-transfer operation. Transfer efficiency ranging between 0.998 and 0.999 is obtained for surface n-channel devices with clock cycle times in the range from 40 ns to 0.3 ms. Transfer efficiency as high as 0.9999 is obtained for buried n-channel devices. Good agreement is found between experiment and simulation.

Fossum, Eric R.↗
NASA NTRS1991

A resistive-gate Al(0.3)Ga(0.7)As/GaAs 2DEG CCD with high charge-transfer efficiency at 1 GHz

The fabrication and performance of an Al(0.3)Ga(0.7)As/GaAs modulation-doped resistive-gate CCD are reported. The two-dimensional electron gas (2DEG) CCD, implemented as a 32-stage four-phase delay line, was tested at both low (1-13 MHz) and high (0.6-1.0 GHz) frequency. It exhibits a room-temperature charge-transfer efficiency (CTE) of better than 0.999 at clock frequencies from 10 MHz up to 1 GHz without a fat-zero signal and is limited by dark current below 10 MHz. The high-frequency test showed no CTE degradation up to 1-GHz operation. The CTE degraded at frequencies lower than approximately 5 MHz due to dark current. The charge-handling capability and minimum clock swing of the resistive-gate 2DEG CCD are calculated.

Song, J.-I.↗
NASA NTRS1991

Precluding nonlinear ISI in direct detection long-haul fiber optic systems

Long-distance, high-rate fiber optic systems employing directly modulated 1.55-micron single-mode lasers and conventional single-mode fiber suffer severe intersymbol interference (ISI) with a large nonlinear component. A method of reducing the nonlinearity of the ISI, thereby making linear equalization more viable, is investigated. It is shown that the degree of nonlinearity is highly dependent on the choice of laser bias current, and that in some cases the ISI nonlinearity can be significantly reduced by biasing the laser substantially above threshold. Simulation results predict that an increase in signal-to-nonlinear-distortion ratio as high as 25 dB can be achieved for synchronously spaced samples at an optimal sampling phase by increasing the bias current from 1.2 times threshold to 3.5 times threshold. The high SDR indicates that a linear tapped delay line equalizer could be used to mitigate ISI. Furthermore, the shape of the pulse response suggests that partial response precoding and digital feedback equalization would be particularly effective for this channel.

Swenson, Norman L.↗
NASA NTRS1992

Tracking Comb Filter Suppresses Welder Harmonics

Tracking comb filter includes charge-coupled-device delay line and phase-locked loop. Filter removes harmonics of frequency of repetition of welding-current pulses from acoustic-emission signal. Spurious signals reduced almost to fundamental limit.

Delcher, Ray C.↗
NASA NTRS1992

Multi-user satellite communications system using an innovative compressive receiver

There is a need for an onboard simultaneous multi-channel demodulation system for a satellite communications system. Studies indicate that Convolve Multiply Convolve (CMC) filtering with surface acoustic wave (SAW) dispersive delay lines will eliminate the necessity of onboard satellite channelized filters of complex fourier transform processors. The reason for choosing the CMC technique is its ability to perform Fourier transformations in a shorter time with less space and power consumption than digital Fourier transform processors. Each ground terminal in this multi-users communications system is remotely located and operates independently; hence, a method of synchronizing the transmission of these users is presented which utilizes the existing Global Positioning System (GPS) system. Each ground user is equipped with a low cost ground terminal that has a synchronization subsystem attached to it. The system design of an onboard Multi-channel Receiver and Demodulator utilizes Quadrature Phase Shift Keying (QPSK) as the modulation technique. This technique provides the best figure of merit, i.e., the lowest transmitter power requirement per communication channel.

Staples, Edward J.↗
NASA NTRS1990

Acoustic echo cancellation for full-duplex voice transmission on fading channels

This paper discusses the implementation of an adaptive acoustic echo canceler for a hands-free cellular phone operating on a fading channel. The adaptive lattice structure, which is particularly known for faster convergence relative to the conventional tapped-delay-line (TDL) structure, is used in the initialization stage. After convergence, the lattice coefficients are converted into the coefficients for the TDL structure which can accommodate a larger number of taps in real-time operation due to its computational simplicity. The conversion method of the TDL coefficients from the lattice coefficients is derived and the DSP56001 assembly code for the lattice and TDL structure is included, as well as simulation results and the schematic diagram for the hardware implementation.

Park, Sangil↗
NASA NTRS1991

The measurement system of pulse modulated carrier frequency stability and timing jitter

The definition of pulse modulated carrier frequency stability and timing jitter as well as the configuration and synchronous acquisition measurement method of its measurement system. Frequency stability of the pulse modulated carrier is measured with a discrimination technique. The pulse modulated carrier under testing is mixed with a reference frequency synthesizer. A delay line is used to convert the frequency fluctuation mixed IF signal to the voltage fluctuation. The system has the capability to make the phase noise measurement of two port devices on a pulsed carrier using a phase bridge. The noise voltage mentioned above is applied to the data acquisition and processing unit by PC to realize stability measurement. The data acquisition is in the form of pulse synchronization so that the measurement system accuracy is increased. The pulse width is more than 0.3 microseconds. The phase fluctuation variance, sigma, is less than 0.017. The time interval measuring system with high resolution is used to make interpulse timing and pulse width jitters automatic measurement. The pulse width is less than 0.2 ns. The resolution is 0.1 ns. The system is successfully applied to radar measurement.

Li Cheng-Fu↗
NASA NTRS1992

A gallium-arsenide digital phase shifter for clock and control signal distribution in high-speed digital systems

The design, implementation, testing, and applications of a gallium-arsenide digital phase shifter and fan-out buffer are described. The integrated circuit provides a method for adjusting the phase of high-speed clock and control signals in digital systems, without the need for pruning cables, multiplexing between cables of different lengths, delay lines, or similar techniques. The phase of signals distributed with the described chip can be dynamically adjusted in eight different steps of approximately 60 ps per step. The IC also serves as a fan-out buffer and provides 12 in-phase outputs. The chip is useful for distributing high-speed clock and control signals in synchronous digital systems, especially if components are distributed over a large physical area or if there is a large number of components.

Fouts, Douglas J.↗
NASA NTRS1991

Optical system design for a Lunar Optical Interferometer

The moon offers particular advantages for interferometry, including a vacuum environment, a large stable base on which to assemble multi-kilometer baselines, and a cold nighttime temperature to allow for passive cooling of optics for high IR sensitivity. A baseline design for a Lunar Optical Interferometer (LOI) which exploits these features is presented. The instrument operates in the visible to mid-IL region, and is designed for both astrometry and synthesis imaging. The design uses a Y-shaped array of 12 siderostats, with maximum arm lengths of about 1 km. The inner siderostats are monitored in three dimensions from a central laser metrology structure to allow for high precision astrometry. The outer siderostats, used primarily for synthesis imaging, exploit the availability of bright reference stars in order to determine the instrument geometry. The path delay function is partitioned into coarse and fine components, the former accomplished with switched banks of range mirrors monitored with an absolute laser metrology system, and the latter with a short cat's eye delay line. The back end of the instrument is modular, allowing for beam combiners for astrometry, visible and IR synthesis imaging, and direct planet detection. With 1 m apertures, the instrument will have a point-source imaging sensitivity of about 29 mag; with the laser metrology system, astrometry at the microarcsecond level will be possible.

Colavita, M. M.↗
NASA NTRS1992

The optical very large array and its moon-based version

An Optical Very Large Array (OVLA) is currently in early prototyping stages for ground-based sites, such as Mauna Kea and perhaps the VLT site in Chile. Its concept is also suited for a moon-based interferometer. With a ring of bi-dimensionally mobile telescopes, there is maximal flexibility in the aperture pattern, and no need for delay lines. A circular configuration of many free-flying telescopes, TRIO, is also considered for space interferometers. Finally, the principle of gaseous mirrors may become applicable for moon-based optical arrays. Fifteen years after the first coherent linkage of two optical telescopes, the design of an ambitious imaging array, the OVLA, is now well advanced. Two 1.5 m telescopes have been built and now provide astronomical results. Elements of the OVLA are under construction. Although primarily conceived for ground-based sites, the OVLA structure appears to meet the essential requirements for operation on the Moon.

Labeyrie, Antoine↗
NASA NTRS1993

Acoustic charge transport technology investigation for advanced development transponder

Acoustic charge transport (ACT) technology has provided a basis for a new family of analog signal processors, including a programmable transversal filter (PTF). Through monolithic integration of ACT delay lines with GaAs metal semiconductor field effect transistor (MESFET) digital memory and controllers, these devices significantly extend the performance of PTF's. This article introduces the basic operation of these devices and summarizes their present and future specifications. The production and testing of these devices indicate that this new technology is a promising one for future space applications.

Kayalar, S.↗
NASA NTRS1991

Coherent optical modulation for antenna remoting

A coherent fiber optic link employing wideband frequency modulation (FM) of the optical carrier is used to transfer radio frequency (RF) or microwave signals. This system is used to link a remotely located antenna to a conveniently located electronics processing site. The advantages of coherent analog fiber optic systems over non-coherent intensity modulated fiber optic analog transmission systems are described. An optical FM link employing an indirect transmitter to frequency modulate the optical carrier and a microwave delay line discriminator receiver is described. Measured performance data for a video signal centered at 60 MHz is presented showing the use of wideband FM in the link.

Fitzmartin, D. J.↗
NASA NTRS1991

Comparative study of bolometric and non-bolometric switching elements for microwave phase shifters

The performance of semiconductor and high critical temperature superconductor switches is compared as they are used in delay-line-type microwave and millimeter-wave phase shifters. Such factors as their ratios of the off-to-on resistances, parasitic reactances, power consumption, speed, input-to-output isolation, ease of fabrication, and physical dimensions are compared. Owing to their almost infinite off-to-on resistance ratio and excellent input-to-output isolation, bolometric superconducting switches appear to be quite suitable for use in microwave phase shifters; their only drawbacks are their speed and size. The SUPERFET, a novel device whose operation is based on the electric field effect in high critical temperature ceramic superconductors is also discussed. Preliminary results indicate that the SUPERFET is fast and that it can be scaled; therefore, it can be fabricated with dimensions comparable to semiconductor field-effect transistors.

Tabib-Azar, Massood↗
NASA NTRS1993

Orbiting stellar interferometer for astrometry and imaging

The orbiting stellar interferometer (OSI) is a concept for a first-generation space interferometer with astrometric and imaging goals. The OSI is a triple Michelson interferometer with articulating siderostats and optical delay lines. Two point designs for the instrument are described. The 18-m design uses an 18-m maximum baseline and aperture diameters of 40 cm; the targeted astrometric performance is a wide-field accuracy of 10 microarsec for 16-mag objects in 100 s of integration time and for 20-mag objects in 1 h. The instrument would also be capable of synthesis imaging with a resolution of 5 marcsec, which corresponds to the diffraction limit of the 18-m base line. The design uses a deployed structure, which would fold to fit into an Atlas IIAS shroud, for insertion into a 900-km sun-synchronous orbit. In addition to the 18-m point design, a 7-m point design that uses a shorter base line in order to simplify deployment is also discussed. OSI's high performance is made possible by utilizing laser metrology and controlled-optics technology.

Colavita, M. M.↗
NASA NTRS1992

A 100Mbps coherent optical link demonstration using frequency stabilized solid state lasers

The design, implementation, and performance evaluation of a 100Mbps binary phase shift keying (BPSK) coherent optical link using frequency stabilized solid state lasers is described. In this demonstration, the transmitted data is binary phase modulated at 100Mbps using an external resonant cavity phase modulator. At the receiving end, the signal is detected using a balanced heterodyne detector. An auxiliary frequency tracking loop (FTL) is used to help the initial frequency acquisition before handing over to the carrier phase tracking loop. The FTL is implemented using a delay line discriminator, and the detected frequency error is fed back to the local oscillator laser to close the tracking loop. Phase coherent reception is achieved by synchronizing the carrier phase using a Costas tracking loop. The demonstration showed that a high data rate phase coherent optical link can be implemented using frequency stabilized solid state lasers.

Chen, CHIEN-C.↗
NASA NTRS1995

Superconducting Field-Effect Transistors

Devices offer switching speeds greater than semiconducting counterparts. High-Tc superconducting field-effect transistors (SUPEFETs) investigated for use as electronic switches in delay-line-type microwave phase shifters. Resemble semiconductor field-effect transistors in some respects, but their operation based on different principle; namely, electric-field control of transition between superconductivity and normal conductivity.

Bhasin, Kul↗
NASA NTRS1995

Stabilizing Optical Path Length On A Vibrating Structure

Prototype apparatus constructed to test feasibility of feedback control concept for stabilization of length of optical path between two points on vibrating flexible structure. In original intended application, structure is truss having dimensions of order of meters and supports optical components of stellar interferometer. Interferometry and feedback control reduce path-length disturbances. Some aspects of present feedback control concept and prototype apparatus described in "Controllable Optical Delay Line for Stellar Interferometry" (NPO-18686), and "Test Bed for Control of Optical-Path Lengths" (NPO-18487).

Spanos, John T.↗
NASA NTRS1995

Multilayer Active Control For Structural Damping And Optical-Path Regulation

Two active-control concepts incorporated into system for suppression of vibrations in truss structure and regulation of length of optical path on structure to nanometer level. Optical-path-length-control subsystem contains two feedback control loops to obtain active damping in wide amplitude-and-frequency range. Concept described in more detail in number of previous articles, including "Stabilizing Optical-Path Length on a Vibrating Structure" (NPO-19040), "Controllable Optical Delay Line for Stellar Interferometry" (NPO-18686), "Test Bed for Control of Optical-Path Lengths" (NPO-18487).

Rahman, Zahidul H.↗