Search NASA⌕ Search

SEARCH · Search NASA

Results for “diffusive transport”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Differential multi-probe thermal transport measurements of multi-walled carbon nanotubes grown by chemical vapor deposition

Carbon nanotubes (CNTs) are quasi-one dimensional nanostructures that display both high thermal conductivity for potential thermal management applications and intriguing low-dimensional phonon transport phenomena. In comparison to the advances made in the theoretical calculation of the lattice thermal conductivity of CNTs, thermal transport measurements of CNTs have been limited by either the poor temperature sensitivity of Raman thermometry technique or the presence of contact thermal resistance errors in sensitive two-probe resistance thermometry measurements. Here we report advances in a multi-probe measurement of the intrinsic thermal conductivity of individual multi-walled CNT samples that are transferred from the growth substrate onto the measurement device. The sample-thermometer thermal interface resistance is directly measured by this multi-probe method and used to model the temperature distribution along the contacted sample segment. The detailed temperature profile helps to eliminate the contact thermal resistance error in the obtained thermal conductivity of the suspended sample segment. A differential electro-thermal bridge measurement method is established to enhance the signal-to-noise ratio and reduce the measurement uncertainty by over 40%. The obtained thermal resistances of multiple suspended segments of the same MWCNT samples increase nearly linearly with increasing length, revealing diffusive phonon transport as a result of phonon-defect scattering in these MWCNT samples. The measured thermal conductivity increases with temperature and reaches up to 390 ± 20 W m –1 K –1 at room temperature for a 9-walled MWCNT. In conclusion, theoretical analysis of the measurement results suggests submicron phonon mean free paths due to extrinsic phonon scattering by extended defects such as grain boundaries. The obtained thermal conductivity is decreased by a factor of 3 upon electron beam damage and surface contamination of the CNT sample.

42 ENGINEERING↗
DOE OSTI2023

Fredkin Staircase: An Integrable System with a Finite-Frequency Drude Peak

We introduce and explore an interacting integrable cellular automaton, the Fredkin staircase, that lies outside the existing classification of such automata, and has a structure that seems to lie beyond that of any existing Bethe-solvable model. The Fredkin staircase has two families of ballistically propagating quasiparticles, each with infinitely many species. Despite the presence of ballistic quasiparticles, charge transport is diffusive in the d.c. limit, albeit with a highly non- gaussian dynamic structure factor. Remarkably, this model exhibits persistent temporal oscillations of the current, leading to a delta-function singularity (Drude peak) in the a.c. conductivity at nonzero frequency. Here, we analytically construct an extensive set of operators that anticommute with the time-evolution operator; the existence of these operators both demonstrates the integrability of the model and allows us to lower-bound the weight of this finite-frequency singularity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2026

Core plasma fueling by fast inward particle transport after hydrogen pellet injection in Wendelstein 7-X

A large database of more than 1000 individual cryogenic hydrogen pellets injected into Wendelstein 7-X for plasma fueling was analyzed to improve the understanding of the three phases of the process: the ablation, deposition and transport of the pellet material. Kilohertz-sampled electron density and temperature measurements revealed a more complex drift behavior than predicted by numerical code simulation. It could be explained by the poloidal plasma E r x B- drift rotation, which plays a significant role in stellarators, but was not previously considered in pellet injection codes like HPI2. The drift results in a fast poloidal rotation of the pellet material around the plasma core, leading to an almost homogeneous deposition over the involved flux surfaces regardless of magnetic high and low field side injection geometry. Additionally, a novel fast inward directed transport mechanism (‘FIT-effect’) was observed. The effect occurs on timescales of tens of milliseconds and cannot be explained by neoclassical transport or diffusion. It might be linked to the turbulence pinch recently found in Wendelstein 7-X. When the FIT-effect occurs, the pellet particles are rapidly transferred from the deposition flux surfaces to the plasma core, causing the plasma density profile to peak, which is beneficial for confinement in Wendelstein 7-X. The large pellet injection database was statistical analyzed with regard to pellet and plasma parameters, which delivered some starting points towards developing an understanding of the physics behind the FIT-effect. The results indicate, that plasma core fueling via pellet injection is largely independent of the injection geometry in stellarators under certain conditions, reducing the technical complexity of the injection system.

Wendelstein 7-X↗
DOE OSTI2022

A flexible linear diffusion acceleration to k-eigenvalue neutron transport with SN discontinuous finite element method

In this paper, we derive a flexible linear diffusion acceleration (LDA) for k-eigenvalue neutron transport discretized with discontinuous finite element method (DFEM) and discrete ordinates(SN). This LDA is based on our two pieces of previous works: the flexible non linear diffusion acceleration (NDA) for DFEM-SN and LDA for k-eigenvalue neutron transport using pre-conditioned Jacobian-free Newton-Krylov with self-adjoint angular flux (SAAF), continuous finite element method(CFEM), and SN. We point out the differences between LDA and NDA for DFEM-SN and the difference between DFEM-SN and SAAF-CFEM-SN for LDA. Numerical tests are presented to compare the convergence behaviour of NDA and LDA. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Virtual Volumetric Additive Manufacturing (VirtualVAM)

Abstract Tomographic volumetric additive manufacturing (VAM) produces arbitrary 3D geometries by exposure of a rotating volume of photopolymer resin to tomographically‐patterned illumination. This enables high speed, layer‐less printing of parts from a wide range of photopolymers not amenable to layer‐by‐layer processes. Since the entire geometry is produced at once over the course of a few seconds to minutes, molecular diffusion length scales become significant to the printing process. Understanding these molecular reaction and diffusion processes is imperative for advancing VAM to a usable technology. These processes are experimentally very difficult to monitor and measure. Herein, VirtualVAM ‐ a simulation framework for modeling the tomographic VAM process, is developed and experimentally validated. VirtualVAM simulates reaction, diffusion, and heat generation processes over the course of a print with single‐voxel resolution. From a few experimentally‐determined input parameters and a set of images for projection, VirtualVAM is able to generate a large spatio‐temporal data set for any given tomographic VAM print. Using VirtualVAM, a number of experimentally‐unattainable aspects of the VAM process are investigated such as single‐voxel conversion profiles, effect of molecular oxygen, and stopping time determination. VirtualVAM also enables the optimization of exposure patterns to further improve contrast between in‐part and out‐of‐part delivered dose.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Outgassing of implanted He via short circuit transport along phase and grain boundaries in vapor co-deposited Cu-W nanocomposites

We investigate the response of physical vapor co-deposited copper (Cu)-tungsten (W) nanocomposites to helium (He) implantation. Nuclear reaction analysis (NRA) reveals that a substantial fraction of He implanted into these materials escapes during implantation. Analysis of nanocomposite microstructure shows that the He loss is likely due to its transport out of the material by diffusion along phase and grain boundaries. Lastly, our findings suggest that solid-state interfaces such as phase and grain boundaries are short circuit diffusion pathways for transport of He.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Exponential time differencing for the tracer equations appearing in primitive equation ocean models

The tracer equations are part of the primitive equations used in ocean modeling and describe the transport of tracers, such as temperature, salinity or chemicals, in the ocean. Depending on the number of tracers considered, several equations may be added to and coupled to the dynamics system. In many relevant situations, the time-step requirements of explicit methods imposed by the transport and mixing in the vertical direction are more restrictive than those for the horizontal, and this may cause the need to use very small time steps if a fully explicit method is employed. To overcome this issue, we propose an exponential time differencing (ETD) solver where the vertical terms (transport and diffusion) are treated with a matrix exponential, whereas the horizontal terms are dealt with in an explicit way. In this work, we investigate numerically the computational speed-ups that can be obtained over other semi-implicit methods, and we analyze the advantages of the method in the case of multiple tracers.

42 ENGINEERING↗
DOE OSTI2021

A multi-phase-field model of topological pattern formation during electrochemical dealloying of binary alloys

Porous metal structures produced by electrochemical dealloying have been extensively studied for use in various applications that require high surface areas. A new comprehensive multi-phase-field (MPF) model is proposed to study topological porous patterns formed by spontaneously etching a bulk binary alloy that involves electrochemical reactions, bulk and surface diffusion, ion transport, applied electrode potential, and charge conservation. The governing equations for the alloy-porous cluster-electrolyte system account for a generalized Butler-Volmer electrochemical reaction and are in accordance with the classical nucleation theory. Based on a quantitative examination of the effects of electrode potential and precursor composition, the simulation results reproduce typical phenomena including passive surface dealloying, active porosity evolution, critical potential, and characteristic length scale in two-dimension (2-D) and three-dimension (3-D). To consider more complicated dealloying systems, the evolutions of a bimodal porous metal structure, nanocomposite, and nested porous network with a structured hierarchy are investigated. Finally, the proposed model can be a useful tool for understanding and predicting the morphology evolution of diverse porous structures during electrochemical dealloying.

Hierarchical porous structure↗
DOE OSTI2022

Combustion characteristics and detailed simulations of surrogates for a Tier II gasoline certification fuel

An experimental and numerical study of combustion of a gasoline certification fuel (‘indolene’), and four (S4) and five (S5) component surrogates for it, is reported for the configurations of an isolated droplet burning with near spherical symmetry in the standard atmosphere, and a single cylinder engine designed for advanced compression ignition of pre-vaporized fuel. The intent was to compare performance of the surrogate for these different combustion configurations and to assess the broader applicability of the kinetic mechanism and property database for the simulations. A kinetic mechanism comprised of 297 species and 16,797 reactions was used in the simulations that included soot formation and evolution, and accounted for unsteady transport, liquid diffusion inside the droplet, radiative heat transfer, and variable properties. The droplet data showed a clear preference for the S5 surrogate in terms of burning rate. The simulations showed generally very good agreement with measured droplet, flame, and soot shell diameters. Measurements of combustion timing, in-cylinder pressure, and mass-averaged gas temperature were also well predicted with a slight preference for the S5 surrogate. Preferential vaporization was not evidenced from the evolution of droplet diameter but was clearly revealed in simulations of the evolution of mixture fractions inside the droplets. Here, the influence of initial droplet diameter (D o ) on droplet burning was strong, with S5 burning rates decreasing with increasing D o due to increasing radiation losses from the flame. Flame extinction was predicted for D o =3.0 mm as a radiative loss mechanism but not predicted for smaller D o for the conditions of the simulations.

42 ENGINEERING↗
DOE OSTI2021

In Situ Formation of Polycyclic Aromatic Hydrocarbons as an Artificial Hybrid Layer for Lithium Metal Anodes

Nonuniform Li deposition causes dendrites and low Coulombic efficiency (CE), seriously hindering the practical applications of Li metal. Herein, we developed an artificial solid-state interphase (SEI) with planar polycyclic aromatic hydrocarbons (PAHs) on the surface of Li metal anodes by a facile in situ formation technology. The resultant dihydroxyviolanthron (DHV) layers serve as the protective layer to stabilize the SEI. In addition, the oxygen-containing functional groups in the soft and conformal SEI film can regulate the diffusion and transport of Li ions to homogenize the deposition of Li metal. The artificial SEI significantly improves the CEs and shows superior cyclability of over 1000 h at 4 mAh cm –2 . The LiFePO 4 /Li cell (2.8 mAh cm –2 ) enables a long cyclability for 300 cycles and high CEs of 99.8%. Furthermore, this work offers a new strategy to inhibit Li dendrite growth and enlightens the design on stable SEI for metal anodes.

25 ENERGY STORAGE↗
DOE OSTI2021

Core–Shell Gold Nanoparticle-Star Copolymer Composites with Gradient Transfer and Transport Properties: Toward Electro-Optical Sensors and Catalysis

A series of hybrid core–shell nanomaterials was prepared by solvent phase transfer methods with gold (Au) nanoparticles (NPs) as a core and star copolymers (h-PEI-b-PCL-Cbz) as a shell—consisting of hyperbranched polyethyleneimine (h-PEI) with different poly(ε-caprolactone) (PCL) chain lengths and a carbazole-contained terminating agent (Cbz). By varying the PCL chain length, these core–shell nanomaterials exhibited gradient energy transfer properties, surface hydrophobicity, electropolymerizability, and ionic probe transport and diffusion properties. The systematic copolymer formation was verified with quadruple-detector size exclusion chromatography (SEC) and 1H nuclear magnetic resonance (NMR). High-resolution atomic force microscopy-infrared spectroscopy (AFM-IR) chemical mapping verified nanoparticle-substrate adhesion and film formation. The design of these hybrid NPs and elucidation of gradient properties will be useful for future applications of the core–shell systems in electro-optical sensing and catalysis.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Solar-driven selective conversion of millimolar dissolved carbon to fuels with molecular flux generation

Abstract The direct utilization of dissolved inorganic carbon in seawater for CO 2 conversion promises chemical production on-demand and with zero carbon footprint. Photoelectrochemical (PEC) CO 2 reduction (CO 2 R) devices promise the sustainable conversion of dissolved carbon in seawater to carbon products using sunlight as the only energy input. However, the diffusion-dominant transport mechanism and the near-zero concentration of CO 2 (aq) (CO 2 dissolved in aqueous solution) in static seawater has made it extremely challenging to achieve high solar-to-fuel (STF) efficiency and high carbon-product selectivity. Here, where CO 2 (aq) as a reactant generated in situ by acidification of HCO 3 - flows continuously from BiVO 4 photoanodes to Si photocathodes, enabling a single-step conversion of dissolved carbon into products. Our PEC device significantly increases the CO selectivity from 3% to 21%, which approaches the 30% theoretical limit according to multi-physics modeling. Meanwhile, the Si/BiVO 4 PEC CO 2 R device achieved a STF efficiency of 0.71%. Such flow engineering achieves flow-dependent selectivity, rate, and stability in simulated seawater, thus promising practical solar fuel production at scale.

Liu, Bin↗
DOE OSTI2021

The design of a photoionization front experiment using the Z-Machine as a driving source and estimated measurements

Radiation-driven heat fronts are present in the early universe during reionization, the circumstellar medium of supernovae, and in high-energy-density physics experiments. Dedicated experiments to observe and diagnose the behavior of these types of heat fronts can improve our understanding of these phenomena. A simulation study of photoionization fronts using the HELIOS-CR radiation hydrodynamics code provides an experimental design for the Z-Machine at Sandia National Laboratory using a measurement-calibrated input radiation flux to drive the photoionization front. The simulations use detailed atomic physics and non-diffusive radiation transport in 1D to determine an optimal gas pressure of 0.75 atm for an experiment in N gas as well as the effects of increasing the thickness of the window that seals the gas cell. Post-processing of these simulations demonstrates that ratios of atomic rate coefficients place the heat front in a physics regime where photoionization dominates the energy deposition. Here, to see the sensitivity of the simulations to changes in the model and spatial grid, this analysis performed resolution, atomic model detail, and radiation transport angular grid studies showing less than 10% deviation from the nominal model for increased complexity, when possible. An effort to emulate 3D geometric effects on the radiation flux using an artificial attenuation scheme has shown that, even for conservative estimates of the flux, simulations still produce a photoionization front. Estimations of a streaked, visible spectroscopy measurement using SPECT3D showed that line emission measurements are present early in time and that later in time thermal emission should become dominant.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Less can be more: Insights on the role of electrode microstructure in redox flow batteries from two-dimensional direct numerical simulations

Understanding how to structure a porous electrode to facilitate fluid, mass, and charge transport is key to enhancing the performance of electrochemical devices, such as fuel cells, electrolyzers, and redox flow batteries (RFBs). Here, using a parallel computational framework, direct numerical simulations are carried out on idealized porous electrode microstructures for RFBs. Strategies to improve an electrode design starting from a regular lattice are explored. By introducing vacancies in the ordered arrangement, it is possible to achieve higher voltage efficiency at a given current density, thanks to improved mixing of reactive species, despite reducing the total reactive surface. Careful engineering of the location of vacancies, resulting in a density gradient, outperforms disordered configurations. Our simulation framework is a new tool to explore transport phenomena in RFBs, and our findings suggest new ways to design performant electrodes.

25 ENERGY STORAGE↗
DOE OSTI2023

Further rotation reversal studies in C-Mod L-mode plasmas

Studies of core toroidal rotation reversal phenomenology in C-Mod deuterium L-mode plasmas have been expanded to include details of the dependences on plasma current and toroidal magnetic field. Rotation reversal occurs at a critical density, and universal scaling indicates that the product of ncritq95R ∼ BT/2, with ncrit in 1020/m3, R in m, and BT in T. Measurements in H and He plasmas exhibit similar behavior, including a connection with the linear Ohmic confinement/saturated Ohmic confinement transition and the cutoff for non-diffusive heat transport. Electron density and ion cyclotron range of frequencies power modulation experiments suggest that the collisionality ν* is a unifying parameter. Strong impurity puffing causes the critical density to increase, indicating that the situation is more complicated than only collisionality, perhaps involving the details of the effects of dilution on ion temperature gradient mode stability.

Physics↗
DOE OSTI2026

ML-Based Pebble Power Reconstruction for Pebble Bed Reactor Analysis

Pebble power reconstruction has been explored to complement the conventional homogenized modeling approach in pebble bed reactor (PBR) analysis, as detailed heterogeneous geometry calculations are computationally expensive. The random distribution of pebble fuels within the core challenges the application of conventional pin power reconstruction methods. To address this, we introduce a machine learning approach based on the transformer model, composed of encoder and decoder layers, to estimate the flux and power form functions for reconstructing individual pebble neutron fluxes and powers. The homogeneous neutron flux distribution within each spectral zone (SZ) is obtained from finite element solutions of global diffusion or transport calculations. Verification tests demonstrate that the trained transformer model accurately predicts power form functions over a range of conditions, including variations in pebble enrichment, location, type, SZ size, and burnup. In particular, verification using a three-dimensional PBR benchmark with burned pebbles shows good agreement in heterogeneous pebble power distributions between Griffin and Serpent. These results highlight the potential of applying conventional pin power reconstruction approaches to PBR cores with randomly distributed pebbles.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Development of an atomic layer deposition system for deposition of alumina as a hydrogen permeation barrier

Tritium permeation into and through materials poses a critical challenge for the development of nuclear fusion reactors. Minimizing tritium permeation is essential for the safe and efficient use of available fuel supplies. In this work, we present the design, construction, and validation of custom atomic layer deposition (ALD) and deuterium permeation measurement systems aimed at developing thin-film hydrogen permeation barriers. Using the ALD system, we deposited conformal $\mathrm{Al}_{2}\mathrm{O}_{3}$ films on copper foil substrates and characterized their growth behavior, morphology, and composition. ALD growth rates of ∼1.1 Å/cycle were achieved for temperatures between 100 ∘ C and 210 ∘ C. Permeation measurements on bare and alumina coated copper foils revealed a significant reduction in deuterium flux with the addition of a ∼10 nm $\mathrm{Al}_{2}\mathrm{O}_{3}$ layer. While bare copper followed diffusion-limited transport consistent with Sievert’s law, the alumina-coated samples exhibited surface-limited, pore-mediated transport with linear pressure dependence. Arrhenius analysis showed distinct differences in activation energy for the two transport regimes, and permeation reduction factors exceeding an order of magnitude were observed. These results demonstrate the potential of ALD-grown $\mathrm{Al}_{2}\mathrm{O}_{3}$ films as effective hydrogen isotope barriers and provide a foundation for future studies on film optimization and integration into fusion-relevant components.

atomic layer deposition↗