Search NASA⌕ Search

SEARCH · Search NASA

Results for “directional heating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Large Scale Flame Spread Environmental Characterization Testing

Under the Advanced Exploration Systems (AES) Spacecraft Fire Safety Demonstration Project (SFSDP), as a risk mitigation activity in support of the development of a large-scale fire demonstration experiment in microgravity, flame-spread tests were conducted in normal gravity on thin, cellulose-based fuels in a sealed chamber. The primary objective of the tests was to measure pressure rise in a chamber as sample material, burning direction (upward/downward), total heat release, heat release rate, and heat loss mechanisms were varied between tests. A Design of Experiments (DOE) method was imposed to produce an array of tests from a fixed set of constraints and a coupled response model was developed. Supplementary tests were run without experimental design to additionally vary select parameters such as initial chamber pressure. The starting chamber pressure for each test was set below atmospheric to prevent chamber overpressure. Bottom ignition, or upward propagating burns, produced rapid acceleratory turbulent flame spread. Pressure rise in the chamber increases as the amount of fuel burned increases mainly because of the larger amount of heat generation and, to a much smaller extent, due to the increase in gaseous number of moles. Top ignition, or downward propagating burns, produced a steady flame spread with a very small flat flame across the burning edge. Steady-state pressure is achieved during downward flame spread as the pressure rises and plateaus. This indicates that the heat generation by the flame matches the heat loss to surroundings during the longer, slower downward burns. One heat loss mechanism included mounting a heat exchanger directly above the burning sample in the path of the plume to act as a heat sink and more efficiently dissipate the heat due to the combustion event. This proved an effective means for chamber overpressure mitigation for those tests producing the most total heat release and thusly was determined to be a feasible mitigation strategy to incorporate into the microgravity experiment.

Clayman, Lauren K.↗

Mars 2020 Entry, Descent, and Landing Instrumentation 2 (MEDLI2) Sensor Suite

The Mars 2020 Entry, Descent, and Landing Instrumentation 2 (MEDLI2) sensor suite seeks to address the aerodynamic, aerothermodynamic, and thermal protection system (TPS) performance issues during atmospheric entry, descent, and landing of the Mars 2020 mission. Based on the highly successful instrumentation suite that flew on Mars Science Laboratory (MEDLI), the new sensor suite expands on the types of measurements and also seeks to answer questions not fully addressed by the previous mission. Sensor Package: MEDLI2 consists of 7 pressure transducers, 17 thermal plugs, 2 heat flux sensors, and one radiometer. The sensors are distributed across both the heatshield and backshell, unlike MEDLI (the first sensor suite), which was located solely on the heat-shield. The sensors will measure supersonic pressure on the forebody, a pressure measurement on the aftbody, near-surface and in-depth temperatures in the heatshield and backshell TPS materials, direct total heat flux on the aftbody, and direct radiative heating on the aftbody. Instrument Development: The supersonic pressure transducers, the direct heat flux sensors, and the radiometer all were tested during the development phase. The status of these sensors, including the piezo-resistive pressure sensors, will be presented. The current plans for qualification and calibration for all of the sensors will also be discussed. Post-Flight Data Analysis: Similar to MEDLI, the estimated flight trajectory will be reconstructed from the data. The aerodynamic parameters that will be reconstructed will be the axial force coefficient, freestream Mach number, base pressure, atmospheric density, and winds. The aerothermal quantities that will be determined are the heatshield and backshell aero-heating, turbulence transition across the heatshield, and TPS in-depth performance of PICA. By directly measuring the radiative and total heat fluxes on the back-shell, the convective portion of the heat flux will be estimated. The status of the current tools to perform the post-flight data analysis will be presented, along with plans for model improvements.

Hwang, Helen H.↗

Mars 2020 Entry, Descent, and Landing Instrumentation 2 (MEDLI2) Sensor Suite

The Mars 2020 Entry, Descent, and Landing Instrumentation 2 (MEDLI2) sensor suite seeks to address the aerodynamic, aerothermodynamic, and thermal protection system (TPS) performance issues during atmospheric entry, descent, and landing of the Mars 2020 mission. Based on the highly successful instrumentation suite that flew on Mars Science Laboratory (MEDLI), the new sensor suite expands on the types of measurements and also seeks to answer questions not fully addressed by the previous mission. Sensor Package: MEDLI2 consists of 7 pressure transducers, 17 thermal plugs, 2 heat flux sensors, and one radiometer. The sensors are distributed across both the heatshield and backshell, unlike MEDLI (the first sensor suite), which was located solely on the heat-shield. The sensors will measure supersonic pressure on the forebody, a pressure measurement on the aftbody, near-surface and in-depth temperatures in the heatshield and backshell TPS materials, direct total heat flux on the aftbody, and direct radiative heating on the aftbody. Instrument Development: The supersonic pressure transducers, the direct heat flux sensors, and the radiometer all were tested during the development phase. The status of these sensors, including the piezo-resistive pressure sensors, will be presented. The current plans for qualification and calibration for all of the sensors will also be discussed. Post-Flight Data Analysis: Similar to MEDLI, the estimated flight trajectory will be reconstructed from the data. The aerodynamic parameters that will be reconstructed will be the axial force coefficient, freestream Mach number, base pressure, atmospheric density, and winds. The aerothermal quantities that will be determined are the heatshield and backshell aero-heating, turbulence transition across the heatshield, and TPS in-depth performance of PICA. By directly measuring the radiative and total heat fluxes on the back-shell, the convective portion of the heat flux will be estimated. The status of the current tools to perform the post-flight data analysis will be presented, along with plans for model improvements.

Hwang, Helen↗

A comparison of estimated and directly measured turbulent heat fluxes in the lower stratosphere

The contribution of small-scale motions to the vertical heat flux in the lower stratosphere is determined from wind and temperature fluctuation statistics obtained during the High Altitude Clear Air Turbulence investigation. Analysis of the cospectra suggests a horizontal wavelength of 3 km as the appropriate long-wave cutoff of small-scale motion. With this scale restriction, the measured vertical heat fluxes are in good agreement with the values of heat flux estimated by Lilly et al. (1974) from the kinetic energy dissipation rate. Hence, the hypothesis of Lilly et al. for estimating heat flux from the dissipation rate is considered to be reliable. It follows that, in the lower stratosphere, subsynoptic vertical transport is small compared to large-scale transport.

Heck, W.↗

Direct electric field heating and acceleration of electrons in solar flares

We show that the observed properties of solar flare X-ray and microwave emission can be explained through the Joule heating and electric field acceleration of runaway electrons in current channels. The global properties of the flaring region required for this are presented. We have fit a hybrid thermal/nonthermal electron distribution, consisting of hot, isothermal electrons with a nonthermal tail of runaway electrons, to high-resolution hard X-ray and microwave spectra and have obtained excellent fits to both. The hybrid model relaxes the electron number and energy flux requirements for the hard X-ray emission over those of a purely nonthermal model. The model also provides explanations for several previously unexplained aspects of the high-resolution microwave spectra. The fit parameters can be related to physical properties (such as the electric field strength in the current channels) of the acceleration region.

Holman, Gordon D.↗

Direct Electricity from Heat: A Solution to Assist Aircraft Power Demands

A thermionic device produces an electrical current with the application of a thermal gradient whereby the temperature at one electrode provides enough thermal energy to eject electrons. The system is totally predicated on the thermal gradient and the work function of the electrode collector relative to the emitter electrode. Combined with a standard thermoelectric device high efficiencies may result, capable of providing electrical energy from the waste heat of gas turbine engines.

Goldsby, Jon C.↗

Radiant heat transfer between nongray directional surfaces.

Real surface property effects on local and overall heat transfer are studied for a simple system of interacting opaque surfaces. Wavelength, temperature and directional dependence of surface properties is included in the analysis for equal and unequal temperature specularly reflecting surfaces. Tungsten is employed as a representative metal and Roberts' model is used to describe the wavelength and temperature dependence of its optical parameters. The relationships of electromagnetic theory are employed to describe the directional dependence of spectral properties. Numerical results establish that gray direction independent property analysis adequately predicts the general trends of real surface analysis. The results also establish that spectral and temperature dependence of surface properties influences radiant heat transfer to a greater degree than does directional dependence of properties. Property models which adequately account for the nongray character of engineering surfaces while neglecting directional dependence of properties can provide heat transfer results of acceptable engineering accuracy.

Fischer, W. D.↗

Regressed relations for forced convection heat transfer in a direct injection stratified charge rotary engine

Currently, the heat transfer equation used in the rotary combustion engine (RCE) simulation model is taken from piston engine studies. These relations have been empirically developed by the experimental input coming from piston engines whose geometry differs considerably from that of the RCE. The objective of this work was to derive equations to estimate heat transfer coefficients in the combustion chamber of an RCE. This was accomplished by making detailed temperature and pressure measurements in a direct injection stratified charge (DISC) RCE under a range of conditions. For each specific measurement point, the local gas velocity was assumed equal to the local rotor tip speed. Local physical properties of the fluids were then calculated. Two types of correlation equations were derived and are described in this paper. The first correlation expresses the Nusselt number as a function of the Prandtl number, Reynolds number, and characteristic temperature ratio; the second correlation expresses the forced convection heat transfer coefficient as a function of fluid temperature, pressure and velocity.

Lee, Chi M.↗

Regressed relations for forced convection heat transfer in a direct injection stratified charge rotary engine

Currently, the heat transfer equation used in the rotary combustion engine (RCE) simulation model is taken from piston engine studies. These relations have been empirically developed by the experimental input coming from piston engines whose geometry differs considerably from that of the RCE. The objective of this work was to derive equations to estimate heat transfer coefficients in the combustion chamber of an RCE. This was accomplished by making detailed temperature and pressure measurements in a direct injection stratified charge (DISC) RCE under a range of conditions. For each specific measurement point, the local gas velocity was assumed equal to the local rotor tip speed. Local physical properties of the fluids were then calculated. Two types of correlation equations were derived and are described in this paper. The first correlation expresses the Nusselt number as a function of the Prandtl number, Reynolds number, and characteristic temperature ratio; the second correlation expresses the forced convection heat transfer coefficient as a function of fluid temperature, pressure and velocity.

Lee, Chi M.↗

Directional control of radiant heat

Surface with grooves having flat bases gives directional emissivities and absorptivities that can be made to approximate a perfect directional surface. Radiant energy can then be transferred in desired directions.

Howell, J. R.↗

Comparison of Direct Solar Energy to Resistance Heating for Carbothermal Reduction of Regolith

A comparison of two methods of delivering thermal energy to regolith for the carbo thermal reduction process has been performed. The comparison concludes that electrical resistance heating is superior to direct solar energy via solar concentrators for the following reasons: (1) the resistance heating method can process approximately 12 times as much regolith using the same amount of thermal energy as the direct solar energy method because of superior thermal insulation; (2) the resistance heating method is more adaptable to nearer-term robotic exploration precursor missions because it does not require a solar concentrator system; (3) crucible-based methods are more easily adapted to separation of iron metal and glass by-products than direct solar energy because the melt can be poured directly after processing instead of being remelted; and (4) even with projected improvements in the mass of solar concentrators, projected photovoltaic system masses are expected to be even lower.

Muscatello, Anthony C.↗

Middle Atmosphere Response to Different Descriptions of the 11-Year Solar Cycle in Spectral Irradiance in a Chemistry-Climate Model

The 11-year solar cycle in solar spectral irradiance (SSI) inferred from measurements by the SOlar Radiation & Climate Experiment (SORCE) suggests a much larger variation in the ultraviolet than previously accepted. We present middle atmosphere ozone and temperature responses to the solar cycles in SORCE SSI and the ubiquitous Naval Research Laboratory (NRL) SSI reconstruction using the Goddard Earth Observing System chemistry-climate model (GEOS CCM). The results are largely consistent with other recent modeling studies. The modeled ozone response is positive throughout the stratosphere and lower mesosphere using the NRL SSI, while the SORCE SSI produces a response that is larger in the lower stratosphere but out of phase with respect to total solar irradiance above 45 km. The modeled responses in total ozone are similar to those derived from satellite and ground-based measurements, 3-6 Dobson Units per 100 units of 10.7-cm radio flux (F10.7) in the tropics. The peak zonal mean tropical temperature response 50 using the SORCE SSI is nearly 2 K per 100 units 3 times larger than the simulation using the NRL SSI. The GEOS CCM and the Goddard Space Flight Center (GSFC) 2-D coupled model are used to examine how the SSI solar cycle affects the atmosphere through direct solar heating and photolysis processes individually. Middle atmosphere ozone is affected almost entirely through photolysis, whereas the solar cycle in temperature is caused both through direct heating and photolysis feedbacks, processes that are mostly linearly separable. Further, the net ozone response results from the balance of ozone production at wavelengths less than 242 nm and destruction at longer wavelengths, coincidentally corresponding to the wavelength regimes of the SOLar STellar Irradiance Comparison Experiment (SOLSTICE) and Spectral Irradiance Monitor (SIM) on SORCE, respectively. A higher wavelength-resolution analysis of the spectral response could allow for a better prediction of the atmospheric response to arbitrary SSI variations.

Swartz, W. H.↗

Martian B Storm Genesis and Evolution: Initial Analysis of Thermal Datasets.

Introduction: Dust lifting on Mars likely occurs primarily as a result of the exchange of momentum between the atmosphere and the surface via saltation. During saltation, sand-sized particles are mobilized but do not enter into suspension. When these larger particles fall back to the surface, kinetic energy is transferred to smaller dust particles which are then lofted into suspension in the atmosphere. Depending on the altitude to which dust is lofted, it can have a significant effect on atmospheric temperatures. As a strong absorber and emitter in the infrared, dust can influence atmospheric heating and modify the global circulation and weather on Mars [1,2]. Although dust is present in Mars’ atmosphere throughout the year, the atmosphere is generally dustier during the second half of the year when Mars is near perihelion. Observations reveal that episodic global-scale dust storms and fairly regular regional-scale dust storms are superimposed on a well-defined and highly repeatable seasonal cycle of dust opacity and associated mid-level atmospheric temperature responses. Kass et al. (2016) used 50 Pa temperature observations from MRO/MCS to identify three highly repeatable time periods during which regional dust storms occur, and designated them the “A”, “B” and “C” storms. While “A” and “C” storms have been studied a fair amount to-date, “B” storms have not yet been investigated in detail. This study explores the generation and evolution of the annually recurring regional dust storm known as the “B” storm, which was identified and categorized by Kass et al. (2016) based on 25 km (50 Pa) temperature observations. The B storm is a southern-hemisphere (SH) phenomenon that originates at the cap edge just after perihelion and which reaches peak intensity during the SH summer solstice, Ls 270. It may originate from the cap edge storms that spawn near the edge of the seasonal CO2 cap during retreat, but the mechanisms for B storm genesis have yet to be determined definitively [1]. Methods: We will use observational data sets and a global climate model (GCM) to investigate “B” regional storms. The data analysis component will include the analysis of imagery from MGS/MOC and MRO/MARCI, and spectroscopic data sets of dust and temperatures from MGS/TES and MRO/MCS with the goal of fully characterizing the behavior of these storms. Both MGS and TES provide data well-suited for temperature analysis at 25 km. MCS measures atmospheric temperature, dust extinction, and water ice extinction at 5 km intervals from the surface to about 80 km. TES measured atmospheric temperatures, column dust and water ice opacities, and column water vapor abundances. Measurements made by TES extended from the surface to about 40 km [1]. At the 50 Pa (25 km) level, local dust events usually confined to shallower depths are effectively filtered out of the analysis leaving the regional dust events identifiable by their temperature signatures [1]. Our preliminary analysis makes use of the fact that the brightness temperature at 15 microns (T15 temperature) is a close approximation to observed temperature at 25 km. We first reproduce the zonal mean 50 Pa level temperature plots for MY 29-32 to establish a baseline for our procedures moving forward [1]. Expanding on Kass et al. (2016), we include recent MCS data from MY 33 and 34 as well. Preliminary Analysis: The daytime (3PM) T15 temperatures in Figure 1 indicate: in MY 29, a strong A storm at Ls 240, a B storm at high southern latitudes just after Ls 270, and a C storm at Ls 320; in MY 30, a B storm at Ls 270; in MY 31 & MY 32, a B storm just before Ls 270; in MY 33, a B storm at Ls 270; and in MY 34, a strong A storm in the northern hemisphere at Ls 210, and a B storm around Ls 270 although there is a data gap. For the B storms, each is indicative of lofted dust and resultant warming. The daytime temperature structure illustrates that the B storm occurs annually around Ls 270 and is confined to high southern latitudes. It reaches its peak intensity around SH summer solstice, Ls 270, consistently for all six MY assessed. Since direct solar heating is absent overnight, the nighttime T15 temperatures (Figure 2) are often useful for differentiating the heat signature of direct solar heating from the dynamical response to that heating. However, in the southern polar latitudes at perihelion the sun does not set and direct solar heating remains present throughout the night. Importantly for our study, dust lofted in the B storm experiences this direct heating day and night for the entirety of its lifetime. The B storm expands as far north as -60 latitude and decays in latitudinal extent more gradually than it grows. This feature is less obvious in the nighttime (3AM) T15 temperatures (Figure 2). The temperature signal is stronger at night for MY 30-33. The warm pool is larger in area relative to the background at night in these four cases. This more uniform warming masks the “tail” feature somewhat, such that it is barely noticeable during these years. Unfortunately, gaps in MCS data in MY 29 and 34 prevent confirmation of the tail feature during those years, however, the B storm temperature signature follows a very different pattern than that described for MY 30-33. MY 29 and 34 appear to show smaller centers of warming at night and larger centers of warming during the day. This is in opposition to that previously described for MY 30-33. Conclusions and Future Work: We will continue investigating the heat signatures of B storms by looking at the total column heating as recorded by TES. We will also look at lower altitudes for patterns that may describe the relationship between B storms and the cap edge storms that develop while the seasonal cap is retreating. In the future, we will use GCM simulations to determine the atmospheric and thermo-dynamic conditions associated with these storms.

Courtney Marylou Batterson↗

Impulsive phase heating by uni-directional current systems in solar flares

The possibility of producing rapid heating of a substantial coronal volume by current dissipation, driven by a tearing instability associated with a single unidirectional current system, is investigated. For the fast tearing mode, it is found that, for initial growth rates gamma(f) equal or less than 0.3/s, the electron heating is offset by convective losses, resulting in a very slow temperature rise, and hard X-ray emitting temperatures are never realized. For the larger growth rates, heating from 10 to the 7th to 10 to the 8th K can be achieved in a few seconds; however, in this regime, the maximum volume heated is some three to five orders of magnitude less than the volume of heated material that is inferred from hard X-ray emission measures. The results suggest that to achieve the required heating for the fast tearing mode, a more complicated geometry involving multiple small-scale, oppositely directed current channels may be necessary.

La Rosa, T. N.↗

Advanced Thermal Control Flight Experiment.

The advanced Thermal Control Flight Experiment on the Applications Technology Satellite (ATS-F) will evaluate, for the first time in a space environment, the performance of a feedback-controlled variable conductance heat pipe and a heat pipe thermal diode. In addition, the temperature control aspects of a phase-change material (PCM) will be demonstrated. The methanol/stainless steel feedback-controlled heat pipe uses helium control gas that is stored in a wicked reservoir. This reservoir is electrically heated through a solid state controller that senses the temperature of the heat source directly. The ammonia/stainless steel diode heat pipe uses excess liquid to block heat transfer in the reverse direction. The PCM is octadecane. Design tradeoffs, fabrication problems, and performance during qualification and flight acceptance tests are discussed.

Kirkpatrick, J. P.↗