Search NASA⌕ Search

SEARCH · Search NASA

Results for “distributed designs”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Performance of a bicone inlet designed for Mach 2.5 with internal distributed compression and 40 percent internal contraction

The inlet was designed to have the minimum internal contraction consistent with high total-pressure recovery and low cowl drag. Without a bypass system, the peak pressure recoveries increased from 0.890 to 0.936 when the supercritical bleed mass flow ratio was varied from 0.035 to 0.060. With an operating bypass system and installed centerbody vortex generators, a slight increase in peak pressure recovery was obtained. The values of steady-state distortion and dynamic distortion were below 0.10 and 0.02, respectively, near critical operation. Simulation of a turbofan engine with concentric pipes showed no effect on compressor face flow profiles with varying bypass flow ratio.

Wasserbauer, J. F.↗
NASA NTRS1953

Method of Estimating the Incompressible-flow Pressure Distribution of Compressor Blade Sections at Design Angle of Attack

A method was devised for estimating the incompressible-flow pressure distribution over compressor blade sections at design angle of attack. The theoretical incremental velocities due to camber and thickness of the section as an isolated airfoil are assumed proportional to the average passage velocity and are modified by empirically determined interference factors. Comparisons were made between estimated and test pressure distributions of NACA 65-series sections for typical conditions. Good agreement was obtained.

COMPRESSOR FLOW THEORY AND EXPERIMENT↗
NASA NTRS1998

An Object-Oriented Interface to the CCSDS Ground Telecommand Services

The Telecommand Data Routing and Channel Services defined by the Consultative Committee for Space Data Systems (CCSDS) are flexible enough to support a myriad of commanding models. Because the standard is so broad, the traditional approach has been to implement only the portion of the standard needed by the particular spacecraft being tested/operated. Tasked with providing Telecommand Services for an entire class of spacecraft, where each spacecraft may choose any valid CCSDS commanding model, NASA Code 584 designed a common architecture capable of handling the full CCSDS protocol. The solution uses another CCSDS standard - the Standard Formatted Data Unit (SFDU) as the interface to the Telecommand Services. SFDUs provide a consistent way of labelling data objects, as well as allowing data objects to encapsulate other data objects. The resulting interface is: - Flexible: The full Data Routing and Channel Services are available via a single interface. The client (i.e. the command source) may enter commands at any layer within the protocol stack, specify any of the data aggregation or segmentation methods, and dynamically set any configuration parameter defined in the standard. - Object-oriented: Each object specifies both the data and the actions to be performed with the data. An object may contain other objects. - Expandable: New capabilities are added by defining new objects. Objects pass thru the protocol layers until they reach the applicable layer. The resulting design is: - Modular: The logic for each protocol layer is contained in a separate Application Program Interface (API). The objects used for the external interface are also used for communication between layers. - Distributable: The design can be split along any layer boundary for distribution across multiple machines. The objects ensure data consistency across platforms. This paper describes the SFDU-based interface and the resulting protocol implementation. The implementation is currently used by NASA (National Aeronautics and Space Administration) for integration & test of the microwave Anisotropy Probe (MAP) and Earth observer-I (EO-l) spacecraft. It will be used for post-launch operations of these spacecraft as well as the Imager for Magnetopause to Aurora Global Exploration (IMAGE) spacecraft.

Ray, Timothy Joseph↗
NASA NTRS1986

The UCLA Design Diversity Experiment (DEDIX) system: A distributed testbed for multiple-version software

To establish a long-term research facility for experimental investigations of design diversity as a means of achieving fault-tolerant systems, a distributed testbed for multiple-version software was designed. It is part of a local network, which utilizes the Locus distributed operating system to operate a set of 20 VAX 11/750 computers. It is used in experiments to measure the efficacy of design diversity and to investigate reliability increases under large-scale, controlled experimental conditions.

Avizienis, A.↗
NASA NTRS1972

Space station ventilation study

A ventilation system design and selection method which is applicable to any manned vehicle were developed. The method was used to generate design options for the NASA 33-foot diameter space station, all of which meet the ventilation system design requirements. System characteristics such as weight, volume, and power were normalized to dollar costs for each option. Total system costs for the various options ranged from a worst case $8 million to a group of four which were all approximately $2 million. A system design was then chosen from the $2 million group and is presented in detail. A ventilation system layout was designed for the MSFC space station mockup which provided comfortable, efficient ventilation of the mockup. A conditioned air distribution system design for the 14-foot diameter modular space station, using the same techniques, is also presented. The tradeoff study resulted in the selection of a system which costs $1.9 million, as compared to the alternate configuration which would have cost $2.6 million.

Colombo, G. V.↗
NASA NTRS1988

Oxygen separation from air using zirconia solid electrolyte membranes

Air separation using a zirconia solid electrolyte membrane is a possible alternative source of oxygen. The process of zirconia oxygen separation is reviewed, and an oxygen plant concept using such separation is described. Potential cell designs, stack designs, and testing procedures are examined. Fabrication of the materials used in a zirconia module as well as distribution plate design and fabrication are examined.

Suitor, J. W.↗
NASA NTRS1988

A transonic-small-disturbance wing design methodology

An automated transonic design code has been developed which modifies an initial airfoil or wing in order to generate a specified pressure distribution. The design method uses an iterative approach that alternates between a potential-flow analysis and a design algorithm that relates changes in surface pressure to changes in geometry. The analysis code solves an extended small-disturbance potential-flow equation and can model a fuselage, pylons, nacelles, and a winglet in addition to the wing. A two-dimensional option is available for airfoil analysis and design. Several two- and three-dimensional test cases illustrate the capabilities of the design code.

Phillips, Pamela S.↗
NASA NTRS2009

Overcoming the Challenges of Implementing a Multi-Mission Distributed Workflow System

A multi-mission approach to solving the same problems for various projects is enticing. However, the multi-mission approach leads to the need to develop a configurable, adaptable and distributed system to meet unique project requirements. That, in turn, leads to a set of challenges varying from handling synchronization issues to coming up with a smart design that allows the "unknowns" to be decided later. This paper discusses the challenges that the Multi-mission Automated Task Invocation Subsystem (MATIS) team has come up against while designing the distributed workflow system, as well as elaborates on the solutions that were implemented. The first is to design an easily adaptable system that requires no code changes as a result of configuration changes. The number of formal deliveries is often limited because each delivery costs time and money. Changes such as the sequence of programs being called, a change of a parameter value in the program that is being automated should not result in code changes or redelivery.

Sayfi, Elias↗
NASA NTRS1972

Propulsion technology for an advanced subsonic transport

Engine design studies for future subsonic commercial transport aircraft were conducted in parallel with airframe studies. These studies surveyed a broad distribution of design variables, including aircraft configuration, payload, range, and speed, with particular emphasis on reducing noise and exhaust emissions without severe economic and performance penalties. The results indicated that an engine for an advanced transport would be similar to the currently emerging turbofan engines. Application of current technology in the areas of noise suppression and combustors imposed severe performance and economic penalties.

Beheim, M. A.↗
DOE OSTI2025

End-to-end microgrid protection using distributed data-driven methods

This paper introduces an end-to-end microgrid protection framework that offers real-time system monitoring, fault-related decision making, and circuit breaker control. This is achieved through the design of distributed data-driven techniques based on the support vector machine method, where each relay is responsible for distributed data collection, fault detection, fault localization, and fault isolation. Local communication is established among neighboring relays, fostering cooperative fault localization and isolation. This decentralized design not only reduces the computational and communication requirements but also enables the adaptability of each relay under varying operational dynamics. The proposed end-to-end protection framework was validated using MATLAB/Simulink simulations on a 100% renewable microgrid, achieving an accuracy of 93.1% with response time of 0.0523 s, in protecting against a range of fault scenarios that are characterized by various types, locations, impedances, load conditions, photovoltaic power levels, and microgrid operating modes.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2024

Towards Cross-Facility Workflows Orchestration through Distributed Automation

Modern science relies on end-to-end workflows that incorporate experimental instruments and utilize edge, cloud, or high-performance computing and storage resources. These components are geographically dispersed across various user facilities and interconnected through high-speed networks. In this paper, we present Zambeze, an automated distributed framework designed to facilitate this new class of cross-facility workflows. Utilizing swarm intelligence principles, Zambeze orchestrates science campaigns by managing distributed autonomous agents. These agents can offer a suite of services, including computing, storage, and data management. We demonstrate the feasibility of Zambeze through a real-world application involving electron microscopy, enhanced with Artificial Intelligence capabilities.

Skluzacek, Tyler↗
NASA NTRS2006

Distributed Antenna-Coupled Transition Edge Sensors

We describe progress toward realizing a new architecture for focal plane arrays for the Submillimeter and Far- Infrared (FIR) bands. This architecture is based on a detector design utilizing distributed hot{electron transition edge sensors (TES) coupled to slot antenna elements. Arrays utilizing this type of detector can be considerably easier to manufacture than membrane-isolated TES arrays, because the need for micro-machining is eliminated. We present background and rationale for this new array architecture and details of a new antenna design for an imaging polarimeter, which yields greater bandwidth than past designs. In addition, we describe a cryogenic facility for testing these arrays.

bolometer↗
NASA NTRS1979

Solar power satellite system definition study, volume 4, phase 2

Results of an overall evaluation of the solar power satellite concept are reported. Specific topics covered include: solid state sandwich configuration; parametric development of reliability design; power distribution system for solid state solar power satellites; multibeam transmission; GEO base system configuration; suppression of the heavy lift launch vehicle trajectory; conceptual design of an offshore space center facility; solar power satellite development and operations scenario; and microwave power transmission technology, advancement, development, and facility requirements.

Source record↗
NASA NTRS1947

Investigation of Axial-flow Fan and Compressor Rotors Designed for Three-dimensional Flow

An investigation has been conducted to determine whether three-dimensional flows may be utilized in axial-flow fan and compressor rotors so that the spanwise load distribution may be varied to obtain high pressure rise. Two rotors, one with approximately uniform and one with solid-body downstream tangential-velocity distributions, were designed and tested at the design blade angle. Radial surveys of total pressure, static pressure, and flow angle were made upstream and downstream of the test rotors through a quantity-coefficient range. Tests of the solid-body rotor were also conducted at a large value of tip clearance. The results indicated that the three-dimensional flows may be utilized with high efficiency and that the three-dimensional theory used in conjunction with two-dimensional cascade data is sufficiently accurate for design purposes. The tests also showed that the tip-clearance losses of rotors highly loaded at the tips are not excessive. The existing three-dimensional theory in simplified for and an illustrative rotor design are presented in appendixes.

Kahane, A↗
NASA NTRS1984

0.5 W 2-21 GHz monolithic GaAs distributed amplifier

A novel circuit concept to reduce the gate loss using series capacitors on the gate feeding lines has been implemented for a distributed amplifier design. It has significantly increased the gate width of the amplifier with a resultant increase of the broadband output power and efficiency. A monolithic GaAs distributed amplifier using 6 x 300-micron FETs has achieved a record output power of 0.5 W over the 2 to 21 GHz frequency band with at least 4 dB gain. The power-added efficiency was 14 percent. The linear gain was 5 plus or minus 1 dB over the same frequency band.

Kim, B.↗
DOE OSTI2024

Approximate 𝑡-Designs in Generic Circuit Architectures

Unitary 𝑡-designs are distributions on the unitary group whose first 𝑡 moments appear maximally random. Previous work has established several upper bounds on the depths at which certain specific random quantum circuit ensembles approximate 𝑡-designs. Here we show that these bounds can be extended to any fixed architecture of Haar-random two-site gates. This is accomplished by relating the spectral gaps of such architectures to those of one-dimensional brickwork architectures. Our bound depends on the details of the architecture only via the typical number of layers needed for a block of the circuit to form a connected graph over the sites. When this quantity is bounded, the circuit forms an approximate 𝑡-design in at most linear depth. We give numerical evidence for a stronger bound that depends only on the number of connected blocks into which the architecture can be divided. We also give an implicit bound for nondeterministic architectures in terms of properties of the corresponding distribution over fixed architectures.

information scrambling↗
NASA NTRS2017

Greased Lightning (GL-10) Flight Testing Campaign

Greased Lightning (GL-10) is an aircraft configuration that combines the characteristics of a cruise efficient airplane with the ability to perform vertical takeoff and landing (VTOL). This aircraft has been designed, fabricated and flight tested at the small unmanned aerial system (UAS) scale. This technical memorandum will document the procedures and findings of the flight test experiments. The GL-10 design utilized two key technologies to enable this unique aircraft design; namely, distributed electric propulsion (DEP) and inexpensive closed loop controllers. These technologies enabled the flight of this inherently unstable aircraft. Overall it has been determined thru flight test that a design that leverages these new technologies can yield a useful VTOL cruise efficient aircraft.

Fredericks, William J.↗