SEARCH · Search NASA

Results for “drop size”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

All sources NASA NTRS DOE OSTI

NASA NTRS2018

Further Examinations of Bimodal SLD Ice Accretion in the NASA Icing Research Tunnel

An ice shape database has been created to document ice accretions on a 72-inch chord NACA 23012 airfoil model resulting from an exposure to a Supercooled Large Drop (SLD) icing cloud with a bimodal drop size distribution. The ice shapes created were documented with photographs, laser scanned surface measurements over a section of the model span, and measurement of the ice mass over the same section of each accretion. The icing conditions used in the test matrix were based upon previously measured ice shapes on the same model to connect the current database to previously measured information. Ice shapes resulting from the bimodal distribution as well as from equivalent mono-modal drop size distributions were obtained and compared. Results indicate that the ice shapes resulting from the bimodal drop size distributions had higher mass and volume values than their mono-modal distribution equivalents as well as having icing limits that extended further back on the chord of the model.

Aircraft↗

NASA NTRS2002

Impact of MIE-Resonances on the Atmospheric Absorption of Water Clouds

Clouds strongly modulate radiative transfer processes in the Earth's atmosphere. Studies, which simulate bulk properties of clouds, such as absorption, require methods that accurately account for multiple scattering among individual cloud particles. Multiple scattering processes are well described by MIE-theory, if interacting particles have a spherical shape. This is a good assumption for water droplets. Thus, simulations for water clouds (especially for interactions with solar radiation) usually apply readily available MIE-codes. The presence of different drop-sizes, however, necessitates repetitive calculations for many sizes. The usual representation by a few sizes is likely to miss contributions from densely distributed, sharp resonances. Despite their usually narrow width, integrated over the entire size-spectrum of a cloud droplet distribution, the impact of missed resonances could add up. The consideration of these resonances tends to increase cloud extinction and cloud absorption. This mechanism for a larger (than by MIE-methods predicted) solar absorption has the potential to explain observational evidence of larger than predicted cloud absorption at solar wavelengths. The presentation will address the absorption impact of added resonances for typical properties of water clouds (e.g. drop size distributions, drop concentrations and cloud geometry). Special attention will be given to scenarios with observational evidence of law than simulated solar absorption; particularly if simultaneous measurements of cloud micro- and macrophysical properties are available.

Wiscombe, W.↗

NASA NTRS1993

Influence of ambient air pressure on effervescent atomization

The influence of ambient air pressure on the drop-size distributions produced in effervescent atomization is examined in this article. Also investigated are the effects on spray characteristics of variations in air/liquid mass ratio, liquid-injection pressure, and atomizer discharge-orifice diameter at different levels of ambient air pressure. It is found that continuous increase in air pressure above the normal atmospheric value causes the mean drop-size to first increase up to a maximum value and then decline. An explanation for this characteristic is provided in terms of the various contributing factors to the overall atomization process. It is also observed that changes in atomizer geometry and operating conditions have little effect on the distribution of drop-sizes in the spray.

Chen, S. K.↗

NASA NTRS2000

Remote Sensing of In-Flight Icing Conditions: Operational, Meteorological, and Technological Considerations

Remote-sensing systems that map aircraft icing conditions in the flight path from airports or aircraft would allow icing to be avoided and exited. Icing remote-sensing system development requires consideration of the operational environment, the meteorological environment, and the technology available. Operationally, pilots need unambiguous cockpit icing displays for risk management decision-making. Human factors, aircraft integration, integration of remotely sensed icing information into the weather system infrastructures, and avoid-and-exit issues need resolution. Cost, maintenance, power, weight, and space concern manufacturers, operators, and regulators. An icing remote-sensing system detects cloud and precipitation liquid water, drop size, and temperature. An algorithm is needed to convert these conditions into icing potential estimates for cockpit display. Specification development requires that magnitudes of cloud microphysical conditions and their spatial and temporal variability be understood at multiple scales. The core of an icing remote-sensing system is the technology that senses icing microphysical conditions. Radar and microwave radiometers penetrate clouds and can estimate liquid water and drop size. Retrieval development is needed; differential attenuation and neural network assessment of multiple-band radar returns are most promising to date. Airport-based radar or radiometers are the most viable near-term technologies. A radiometer that profiles cloud liquid water, and experimental techniques to use radiometers horizontally, are promising. The most critical operational research needs are to assess cockpit and aircraft system integration, develop avoid-and-exit protocols, assess human factors, and integrate remote-sensing information into weather and air traffic control infrastructures. Improved spatial characterization of cloud and precipitation liquid-water content, drop-size spectra, and temperature are needed, as well as an algorithm to convert sensed conditions into a measure of icing potential. Technology development also requires refinement of inversion techniques. These goals can be accomplished with collaboration among federal agencies including NASA, the FAA, the National Center for Atmospheric Research, NOAA, and the Department of Defense. This report reviews operational, meteorological, and technological considerations in developing the capability to remotely map in-flight icing conditions from the ground and from the air.

Ryerson, Charles C.↗

DOE OSTI2020

pars2 (b1)

A laser disdrometer (LDIS) measures the drop size spectra and fall velocity of hydrometeors during precipitation events. The passage of hydrometeors through a horizontal area positioned between an eye-safe laser and an array detector results in blockage of the laser beam in proportion to the size of the drop or particle. In addition to drop/particle size and fall speed, precipitation type is classified. ARM also deploys video disdrometers (VDIS).

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS1982

Application of digital image analysis techniques to antimisting fuel spray characterization

Pulsed ruby laser sheet illumination of the spray is used for the initial recording of data on very-high-resolution photographic film. The digitization of mosaic elements is effected with a vidicon and video digitizer whose output is stored in computer RAM memory for processing. Highly nonspherical elements and a broad range of drop diameters (8-2000 microns) resulting from the unusual rheological properties of the fuel-additive system are accommodated by the device configuration and algorithms. It is found that the generation of two-dimensional images by means of scattered light also eliminates errors resulting from variations in the index of refraction and from the submicron scattering sites that are often present within the modified fuel. No a priori information on the drop size distribution or on the system response to various drop sizes is required.

Fleeter, R.↗

NASA NTRS1977

Atomization of water jets and sheets in axial and swirling airflows

Axial and swirling airflows were used to break up water jets and sheets into sprays of droplets to determine the overall effects of orifice diameter, weight flow of air, and the use of an air swirler on fineness of atomization as characterized by mean drop size. A scanning radiometer was used to determine the mean drop diameter of each spray. Swirling airflows were produced with an axial combustor, 70 deg blake angle, air swirling. Water jets were injected axially upstream, axially downstream and cross stream into the airflow. In addition, pressure atomizing fuel nozzles which produced a sheet and ligament type of breakup were investigated. Increasing the weight flow rate of air or the use of an air swirling markedly reduced the spray mean drop size.

Ingebo, R. D.↗

NASA NTRS1979

Atomization of water jets and sheets in axial and swirling airflows

Ingebo, R. D.↗

NASA NTRS1992

Dual-polarization characteristics of the radar ocean return in the presence of rain

Experimental data are presented on the polarimetric and dual-wavelength characteristics of the ocean surface in the presence of rain. To explain a portion of the variability observed in scatter plots under rain conditions, a storm model is used that incorporates measured drop size distributions. The fairly large variability indicates that effects of drop size distribution and the presence of partially melted particles can introduce a significant error in the estimate of attenuation. This effect is especially significant in the case of a 10-GHz radar under high rain rates. A surface reference method at this frequency will tend to overestimate the rain attenuation unless melting layer attenuation is properly taken into account. Observations of the cross-polarization return in stratiform rain over an ocean surface show three distinct components. Two of these correspond to aspherical, nonaligned particles in the melting layer seen in the direct and mirror-image returns. The remaining part depends both on the off-nadir depolarization by the surface and on the rain medium. A possible mechanism for this latter effect is the bistatic scattering from the rain to the surface.

Meneghini, R.↗

NASA NTRS2015

NASA Glenn Icing Research Tunnel: 2014 and 2015 Cloud Calibration Procedures and Results

This report summarizes the current status of the NASA Glenn Research Center (GRC) Icing Research Tunnel cloud calibration: specifically, the cloud uniformity, liquid water content, and drop-size calibration results from both the January-February 2014 full cloud calibration and the January 2015 interim cloud calibration. Some aspects of the cloud have remained the same as what was reported for the 2014 full calibration, including the cloud uniformity from the Standard nozzles, the drop-size equations for Standard and Mod1 nozzles, and the liquid water content for large-drop conditions. Overall, the tests performed in January 2015 showed good repeatability to 2014, but there is new information to report as well. There have been minor updates to the Mod1 cloud uniformity on the north side of the test section. Also, successful testing with the OAP-230Y has allowed the IRT to re-expand its operating envelopes for large-drop conditions to a maximum median volumetric diameter of 270 microns. Lastly, improvements to the collection-efficiency correction for the SEA multi-wire have resulted in new calibration equations for Standard- and Mod1-nozzle liquid water content.

aircraft icing↗

DOE OSTI2022

Study on Emulsification/Demulsification Behavior and Mechanism of Produced Liquid from Polymer Flooding on Alaska North Slope

Heavy oil reservoirs on Alaska North Slope (ANS) are unconsolidated and contain abundant clay minerals, where the first-ever field pilot is currently implemented to validate the use of polymer floods for heavy oil enhanced oil recovery (EOR). The polymer molecules and/or fine clay particles carried with the produced liquid could potentially affect the oil/water separation, which is one of the major concerns for field operators. This dissertation aims to investigate the emulsification behavior of produced liquid, understand the emulsifying mechanism, and seek an adaptive and cost-effective method to treat the produced liquid from polymer flooding. Emulsions were prepared by mechanically mixing the actual heavy oil and the produced water from the pilot site, of which the stability was investigated by bottle test method or multiple light scattering method. Drop size distribution and interfacial properties were measured via microscope and pendant drop technique to probe the stability mechanism further. Results showed that oil-continuous or water-continuous emulsion could be generated depending on the water cut, clay types, clay concentration, and polymer concentration. In the crude oil/water system, the increasing water cut triggered the phase inversion of oil-continuous emulsion to water-continuous emulsion, resulting in faster separation and lower emulsion stability. Whereas, clay particles, no matter added to the oil or water phase, resulted in an unfavorable phase inversion from the loose water-continuous emulsion to the tight oil-continuous emulsion as clay concentration increased. For all four types of clay except Ca-montmorillonite, clay particles added to water led to an earlier phase inversion and higher emulsion stability than that added to the oil. The dual function of polymer on emulsion stability was observed. On the one hand, both sheared and unsheared polymer tended to convert the oil-continuous emulsion formed in either crude oil/water system or complex crude oil/water/clay particle system to the water-continuous emulsion, acting as a weak demulsifier to accelerate the oil/water separation. On the other hand, the addition of polymer to the water-continuous emulsion could result in enhanced emulsion stability, which is primarily attributed to the increased viscosity of the continuous phase and the decreased drop size of the dispersed oil phase. Particularly, the sheared polymer had a weaker ability to stabilize the o/w emulsion than the unsheared polymer due to the lower viscosity of the sheared polymer solution resulting from the breakdown of the polymer macromolecules. As for the chemical demulsification tests, the performance of demulsifiers showed a complex dependency upon the water cut, the shearing intensity, demulsifier type and dosage, and the polymer concentration. A compound emulsion breaker, E12+E18, exhibited the most satisfactory demulsification performance despite the varied test conditions. For severe water-continuous emulsions that might require a multi-fold dosage of demulsifier, a less expensive electrolyte, KCl, was proposed to be used in combination with demulsifier E12+E18 to improve the demulsification performance. In the proposed demulsifier formula, the effectiveness of the commercial demulsifier relied on its destructive effect on the interfacial film, while the efficacy of KCl was mainly dependent on its viscosity reduction effect on the continuous phase. This dissertation illustrates that intermediate layer elimination and water clarification are the major challenges for produced liquid treatment from polymer flooding. It also provides practical and theoretical guidance in advance for the demulsification strategy of the produced liquid from the ongoing first-ever polymer flooding pilot on ANS.

Chang, Hongli↗

NASA NTRS1980

The effect of local parameters on gas turbine emissions

Gas turbine engine inlet parameters reflect changes in local atmospheric conditions. The pollutant emissions for the engine reflects these changes. In attempting to model the effect of the changing ambient conditions on the emissions it was found that these emissions exhibit an extreme sensitivity to some of the details of the combustion process such as the local fuel-air ratio and the size of the drops in the fuel spray. Fuel-air ratios have been mapped under nonburning conditions using a single JT8D-17 combustion can at simulated idle conditions, and significant variations in the local values have been found. Modelling of the combustor employs a combination of perfectly stirred and plug flow reactors including a finite rate vaporization treatment of the fuel spray. Results show that a small increase in the mean drop size can lead to a large increase in hydrocarbon emissions and decreasing the value of the CO-OH rate constant can lead to large increases in the carbon monoxide emissions. These emissions may also be affected by the spray characteristics with larger drops retarding the combustion process. Hydrocarbon, carbon monoxide, and oxides of nitrogen emissions calculated using the model accurately reflect measured emission variations caused by changing engine inlet conditions.

Kauffman, C. W.↗

DOE OSTI2021

Toward a Theory of the Evolution of Drop Morphology and Splintering by Freezing

Abstract The drop freezing process is described by a phase-field model. Two cases are considered: when the freezing is triggered by central nucleation and when nucleation occurs on the drop surface. Depending on the environmental temperature and drop size, different morphological structures develop. Detailed dendritic growth was simulated at the first stage of drop freezing. Independent of the nucleation location, a decrease in temperature within the range from ~−5° to −25°C led to an increase in the number of dendrites and a decrease in their width and the interdendritic space. At temperatures lower than about −25°C, a planar front developed following surface nucleation, while dendrites formed a granular-like structure with small interdendritic distances following bulk nucleation. An ice shell grew in at the same time (but slower) as dendrites following surface nucleation, while it started forming once the dendrites have reached the drop surface in the case of central nucleation. The formed ice morphology at the first freezing stage predefined the splintering probability. We assume that stresses needed to break the ice shell arose from freezing of the water in the interdendritic spaces. Under this assumption, the number of possible splinters/fragments was proportional to the number of dendrites, and the maximum rate of splintering/fragmentation occurred within a temperature range of about −10° to −20°C, is in agreement with available laboratory and in situ measurements. At temperatures < −25°C, freezing did not lead to the formation of significant stresses, making splintering unlikely. The number of dendrites increased with drop size, causing a corresponding increase in the number of splinters. Examples of morphology that favors drop cracking are presented, and the duration of the freezing stages is evaluated. Sensitivity of the freezing process to the surface fluxes is discussed.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS1982

Proceedings of the Second International Colloquium on Drops and Bubbles

Applications of bubble and drop technologies are discussed and include: low gravity manufacturing, containerless melts, microballoon fabrication, ink printers, laser fusion targets, generation of organic glass and metal shells, and space processing. The fluid dynamics of bubbles and drops were examined. Thermomigration, capillary flow, and interfacial tension are discussed. Techniques for drop control are presented and include drop size control and drop shape control.

Lecroissette, D. H.↗

NASA NTRS1988

An experimental study of air-assist atomizer spray flames

It is noted that air-assisted atomizer spray flames encountered in furnaces, boilers, and gas turbine combustors possess a more complex structure than homogeneous turbulent diffusion flames, due to the swirling motion introduced into the fuel and air flows for the control of flame stability, length, combustion intensity, and efficiency. Detailed comparisons are presented between burning and nonburning condition measurements of these flames obtained by nonintrusive light scattering phase/Doppler detection. Spray structure is found to be drastically changed within the flame reaction zone, with changes in the magnitude and shape of drop number density, liquid flux, mean drop size diameter, and drop mean axial velocity radial distributions.

Mao, Chien-Pei↗

NASA NTRS1992

Studies on fuel spray characteristics in high-pressure environment

The present study deals with several issues involving the improvement of physical submodels and the computational efficiency in modeling dense fuel sprays. To improve the computational efficiency, a parcel PDF approach is implemented which can account for turbulent dispersion within each computational parcel. The advantage of a parcel PDF tracking method is to reduce the number of computational parcels representing the spray dynamics as well as to obtain grid-independent solutions for two-phase flows. To account for the dense spray effects, an existing drop collision and coalescence model, two breakup models, and a Reitz's wave instability model were used. These models were incorporated into a state-of-the-art multiphase all-speed transient flow solution procedure. Comparative performance for two breakup models as well as the turbulence modulation effects are also studied. Validation cases include the nonevaporating and evaporating solid-cone dense sprays. The predictions show a reasonably good agreement with available experimental results in terms of spray penetration, drop sizes, gas and drop mean velocities, and gas and drop rms velocities. The numerical results indicate that the present parcel PDF model has the capability of accurately representing drop dispersion in dense sprays with manageable number of computational parcels.

Shang, H. M.↗

NASA NTRS1994

An alternative approach to estimating rainfall rate by radar using propagation differential phase shift

In this work it is shown that for frequencies from 3 to 13 GHz, the ratio of the specific propagation differential phase shift phi(sub DP) to the rainfall rate can be specified essentially independently of the form of the drop size distribution by a function only of the mass-weighted mean drop size D(sub m). This significantly reduces one source of substantial bias errors common to most other techniques for measuring rain by radar. For frequencies 9 GHz and greater, the coefficient can be well estimated from the ratio of the specific differential attenuation to phi(sub DP), while at nonattenuating frequencies such as 3 GHz, the coefficient can be well estimated using the differential reflectivity. In practice it appears that this approach yields better estimates of the rainfall rate than any other current technique. The best results are most likely at 13.80 GHz, followed by those at 2.80 GHz. An optimum radar system for measuring rain should probably include components at a both frequencies so that when signals at 13.8 GHz are lost because of attenuation, good measurements are still possible at the lower frequency.

Jameson, A. R.↗

NASA NTRS1997

Formation and Combustion of Unconfined Drop Clusters in Microgravity

Single-drop and droplet array studies have become common methods to isolate and investigate the effects of any of the complexities that enter into the drop combustion process. Microgravity environments are required to allow larger drops to be studied while minimizing or eliminating the confounding effects of buoyancy. Based on the results from current isolated drop, drop array, and spray studies funded through the Microgravity Science and Applications Division, it has become clear that even with the effects of buoyancy removed, the extrapolation of results from droplet array studies to spray flames is difficult. The problem occurs because even the simplest spray systems introduce complexities of multi-disperse drop sizes and drop-drop interactions, coupled with more complicated fluid dynamics. Not only do these features make the interpretation of experimental data difficult, they also make the problem very difficult to analyze computationally. Group combustion models, in which the interaction between droplets is treated on a statistical manner, have become a popular method to investigate the behavior of large numbers of interacting droplets, particularly through the work of Ryan et al. and Bellan and co-workers. While these models idealize the actual spray systems to a point where they can be treated computationally, the experimental analogy to these models is difficult to achieve because it requires the formation and Combustion of drop clusters without the effects of buoyancy. Therefore, even though these models have provided useful and insightful information, the verification of the results by direct comparison with experimental data is still lacking.

Liu, S.↗