Search NASA⌕ Search

SEARCH · Search NASA

Results for “edge localized modes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Diagnosing the pedestal magnetic field and magnetohydrodynamics radial structure with pedestal–scrape of layer electron cyclotron emission radiation inversion in H-mode plasma (invited)

Forward modeling is used to interpret inversion patterns of the pedestal–Scrape of Layer (SOL) Electron Cyclotron Emission (ECE) in DIII-D H-mode experiments. The modeling not only significantly improves the ECE data interpretation quality but also leads to the potential measurements of (1) the magnetic field strength |B| at the separatrix, (2) the pedestal |B| evolution during an inter-Edge Localized Mode (ELM) period, and (3) the pedestal Magnetohydrodynamics (MHD) radial structure. The ECE shine-through effect leads to three types of pedestal–SOL radiation inversions that are discussed in this paper. The first type of inversion is the non-monotonic T e,rad profile with respect to the major radius. Using the ECE frequency at the minimum T e,rad , the inversion can be applied to measure the magnetic field |B| at the separatrix and calibrate the mapping of the ECE channels with respect to the separatrix. The second type of inversion refers to the opposite phase between the radiation fluctuations δT e,rad at the pedestal and SOL. This δT e,rad phase inversion is sensitive to density and temperature fluctuations at the pedestal foot and, thus, can be used to qualitatively measure the MHD radial structure. The third type of inversion appears when the pedestal and SOL T e,rad evolve in an opposite trend, which can be used to infer the pedestal |B| field change during an inter-ELM period. Finally, the bandwidth effect on measuring δT e,rad due to pedestal MHD is also investigated in the radiation modeling.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Modeling, analysis, and code/data validation of DIII-D tokamak divertor experiments on ELM and non-ELM plasma tungsten sputtering erosion

Abstract We analyzed recent DIII-D tokamak tungsten divertor probe experiments using advanced, coupled, sputter erosion/redeposition, plasma, and surface response code packages. Modeling is done for ELMing H-mode, and L-mode plasmas, impinging on various size tungsten deposits on Divertor Material Evaluation System (DiMES) carbon probes. The simulations compute 3D, full kinetic, sub-gyromotion, impurity sputtering and transport, including changes in tungsten surface composition and response due to mixed deuterium and carbon ions irradiation. Per our analysis, ELM (edge localized mode) plasma sputtering in DIII-D mostly involves free-streaming high energy (∼500–1000 eV) D + and C +6 ions, with high near-surface plasma density. L-Mode sputtering is due to impurity sputtering (C, W) only, with lower density. All cases show complete redeposition of tungsten on the divertor, with significant redeposition on the tungsten spots themselves, and low self-sputtering. Comparison of ELM plasma gross tungsten erosion simulation results with in-situ spectroscopic data is good, as are code/data comparisons of net erosion using post-exposure Rutherford backscattering (RBS) data for the L-mode probes. The analysis, extrapolated to a full tungsten divertor, implies low net erosion and negligible plasma contamination from sputtering. These results support the use of high-Z plasma facing surfaces in ITER and beyond.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Experimental inference of neutral and impurity transport in Alcator C-Mod using high-resolution x-ray and ultra-violet spectra

We present experimental inferences of cross-field impurity transport coefficients for AlcatorC-Mod plasmas without edge-localized modes, leveraging a novel forward model for the entire Ca Kα spectrum, including satellite lines within the spectral range, to compare to high-resolution x-ray imaging crystal spectroscopy (XICS). These measurements are complemented by extreme ultra-violet (EUV) spectroscopy that constrains transport closer to the edge. Using new atomic data sets for both XICS and EUV analysis has enabled consideration of line ratios across both spectral ranges and has increased the accuracy of inferred transport coefficients. Inclusion of charge exchange between edge thermal neutrals and impurities is shown to be extremely important in C-Mod pedestals. Atomic D neutral densities from experimental D Lyα measurements at the midplane are compared to SOLPS-ITER simulations, finding good agreement. Bayesian inferences of impurity transport coefficients are presented for L-, EDA H-, and I-mode discharges, making use of the Aurora package for forward modeling and combining our spectroscopic constraints. Experimentally inferred diffusion profiles are found to match turbulent transport models at midradius within uncertainties, using both quasilinear gyro-fluid TGLF SAT-1 and nonlinear ion-scale gyrokinetic CGYRO simulations. Furthermore, significant discrepancies in convection are observed in some cases, suggesting difficulties in predictions of flat or hollow impurity profiles.

neutrals↗
DOE OSTI2024

Validation of MARS-F modeling of plasma response to RMPs using internal measurements on DIII-D

The linear resistive plasma response model is validated against the plasma internal measurement data from DIII-D edge-localized mode (ELM) control experiments with applied resonant magnetic perturbation (RMP). Considered are DIII-D discharges where the n = 1, 2, and 3 (n is the toroidal mode number) RMP field was applied. Experimental data for the plasma boundary displacement, as well as the three-dimensional (3D) pressure perturbation in the edge pedestal region, are deduced from the vertical Thomson scattering (TS) system and the horizontal charge exchange recombination (CER) system on DIII-D. The linear response model produces results that are in reasonable quantitative agreement with the DIII-D internal measurements. The plasma boundary displacement of up to 15 mm is modeled, with the pedestal pressure perturbation reaching 3 kPa. As an important insight, the larger plasma displacement measured by the vertical TS system, as compared to that measured by the horizontal CER system, is due to the contribution from the tangential component of the plasma displacement to the former. This mixing of displacement components is also found to influence the sensitivity of the CER measurement comparisons. The results of this study provide further confidence in the linear resistive plasma response model for analyzing ELM control experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Resistive wall mode stability and resonant field amplification in MAST high beta plasma

The n=1 (n is the toroidal mode number) resistive wall mode (RWM) instability and the resonant field amplification (RFA) due to a stable RWM response are numerically investigated for a MAST high-pressure plasma scenario, utilizing the MARS-F (Liu Y.Q. et al 2000 Phys. Plasmas 7 3681) and MARS-K (Liu Y.Q. et al 2008 Phys. Plasmas 15 112503) codes, for the purpose of understanding the potential RWM behavior in MAST-U plasmas. Ideal kink stability analysis identifies a target plasma, with parameters similar to that of the reference equilibrium reconstructed from a MAST high-pressure discharge, that accesses the RWM regime. The unstable n=1 RWM for the target equilibrium is subject to strong damping by the plasma toroidal flow and/or the drift kinetic effects from thermal particles. As a result, the mode is found to be stable under the experimental flow conditions, or even without flow stabilization if drift kinetic stabilization is included. The stability prediction is robust against variation of the assumed resistive wall minor radius. Active magneto-hydrodynamic (MHD) spectroscopy modeling, using the magnetic coils designed for controlling the edge localized modes (ELMs) in MAST-U as the antenna, shows strong resonant field amplification due to a stable RWM response in the target plasma. Maximal amplification, of 6-7 times larger than the applied vacuum field within the plasma, is obtained assuming a coil phasing of 120-180 degrees between the upper and lower rows of the ELM control coils. The MHD-kinetic hybrid model predicts generally higher RFA than the fluid model, in particular near the low-field and high-field sides of the plasma boundary surface. Furthermore, the MARS-F/K modeling thus shows that the RWM in MAST-U is subject to strong flow and kinetic stabilization, but can nevertheless be detected by active MHD spectroscopy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Enhancement of edge turbulence concomitant with ELM suppression during boron powder injection in EAST

A reproducible, quasi-stationary edge localized mode (ELM)-suppressed scenario was obtained over a wide range of plasma parameters by continuous injection of boron (B) powder into an upper-single null discharge in the experimental advanced superconducting tokamak [Sun et al., Nucl. Fusion 61, 014002 (2021)]. This powder-induced ELM-absent regime is associated with an edge harmonic mode (EHM) that provides continuous particle exhaust to maintain constant density without confinement degradation and impurity accumulation, the latter of which is often observed in ELM-free regimes. A flow rate threshold of B powder injection, leading to a threshold intensity of the EHM, is necessary for full ELM suppression. The fundamental harmonic of the EHM exhibits a toroidal mode number n = 1. The mode is observable in the entire poloidal cross section with a peak near the upper X-point in an upper-single null configuration. Here, the EHM spans radially across the pedestal and scrape-off layer, peaking inside the separatrix. The EHM appears to be insensitive to q 95 , heating power, plasma toroidal rotation, and pedestal collisionality.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Screening of resonant magnetic perturbation fields assuming various plasma flow models

A recently updated version of the MARS-F code [Y. Q. Liu et al., Phys. Plasmas 7, 3681 (2000); L. Li et al., Phys. Plasmas 25, 082512 (2018); and G. L. Xia et al., Nucl. Fusion 59, 126035 (2019)] is utilized to numerically investigate the plasma screening effect on the applied resonant magnetic perturbation (RMP) field, assuming various equilibrium flow models, including the toroidal flow, the parallel flow and their combinations, and poloidal and toroidal projections of the parallel flow. A parallel equilibrium flow with a uniform radial profile is found to have no effect on plasma screening of the RMP field. A sheared parallel flow, however, does change plasma screening. The poloidal projection of the parallel flow weakens plasma screening in the resistive-inertial regime. The effect on the favorable average curvature regime is found, however, to be non-monotonic. With the increasing flow speed, the poloidal projection first weakens Glasser-Green-Johnson (GGJ)-screening. Further increase in the flow speed results in enhanced GGJ-screening again. This non-monotonic behavior is related to the perturbed parallel shielding current, which appears also off the mode rational surface at fast flow due to additional resonances between the RMP perturbation and the sound wave continuum. These results indicate that flow induced plasma screening to the RMP field can have complicated characteristics, which, in turn, can have implications on the RMP field penetration into the plasma in experiments for controlling the edge localized modes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Results from a new flowing liquid Li limiter with TZM substrate during high confinement plasmas in the EAST device

A third generation flowing liquid lithium (FLiLi) limiter with a substrate made of TZM, an alloy with >99% Mo, was fabricated by conventional manufacturing techniques. TZM has a high corrosion resistance, a high sputtering threshold, and a good wettability to Li, as compared to stainless steel (SS), which had been used as an FLiLi substrate surface in 2014 and 2016. The third generation FLiLi was inserted into the edge in EAST H-mode plasmas in an upper single-null configuration with an ion grad-B drift toward the upper divertor with a limiter temperature of 330–380 °C and an auxiliary heating power of about 2–8 MW. Analysis has shown that by using TZM FLiLi, fuel particle recycling continuously decreased and near-complete edge localized mode elimination was achieved in H-mode plasmas with RF-only heating. The main impurities during the initial FLiLi discharges were Mo, Fe, and W resulting from strong plasma interaction at the Mo plate side, the SS collector, and the upper W divertor. Plasma stored energy increased by about 10 kJ in subsequent FLiLi discharges due to decreased impurity radiation. Engineering analysis shows a uniform lithium flow with an ~80% Li coverage ratio on the limiter surface, similar to the second FLiLi, even though only one of two J × B pumps was functioning. Despite technical difficulties, the FLiLi gen.3 improved the overall plasma performance, providing support for flowing liquid Li plasma facing component applications in present and future devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Optimization of simulated high-field side lower hybrid current drive coupling using machine learning predictions of scrape-off layer density

Lower hybrid current drive (LHCD) is a potential source of non-inductive off-axis current drive (CD) for tokamaks. Although LHCD has been successfully deployed on a number of tokamaks, it is highly sensitive to the scrape-off layer (SOL) conditions local to the LHCD launcher. Large gaps between the launcher and plasma core, SOL turbulence, or edge density perturbations due to edge-localized modes can hamper CD or cause large reflected power. These coupling issues in part motivated the installation of an LHCD launcher on the high-field side (HFS) of DIII-D. On the HFS, the SOL is less turbulent and more controllable compared to the low-field side. This quiescence may result in more predictable edge conditions and thus a more predictable CD. Here, in this work, HFS SOL reflectometry measurements are predicted from global plasma parameters using machine learning models. The SOL predictions coupled with the full-wave simulation of the LHCD launcher allow for the prediction of reflected power, directivity, and arcing risk before the discharge. Launcher performance is then optimized using multi-objective Bayesian optimization, finding the shot parameters that result in an optimal SOL density that maximizes CD while minimizing the risk of arcing. The predictions and optimizations of LHCD performance are then accelerated using a surrogate model of the full-wave LHCD simulation.

Bayesian optimization↗
DOE OSTI2020

H-mode pedestal improvements with neon injection in DIII-D

Improvements in the H-mode pedestal pressure and global energy confinement were determined on DIII-D with both 3 and 6 MW of neutral beam (NBI) heating with neon injection. The pedestal pressure increased, primarily associated with a significant increase in the pedestal density with a relatively smaller decrease in the pedestal temperature. At the same neon injection rate, a rapid decrease in edge localized mode (ELM) frequency and ~35% increase in plasma stored energy were observed in the 3 MW discharge, while in the 6 MW discharge, the ELM frequency was gradually decreased and the plasma stored energy gradually increased by up to 20%. The measured pedestal widths from both 3 and 6 MW discharges matched the EPED1.0 width scaling, ${\Delta _{{\psi _N}}} = 0.089\beta _{p,ped}^{1/2}$ ,data-, within 20% deviations before and after neon injection. The peeling-ballooning mode (PBM) stability analysis showed that after neon injection, the ballooning stability boundary was increased, while the peeling stability boundary only dropped once the neon level was relatively high. The ballooning stability boundary increase with neon injection is consistent with increase of the ion diamagnetic stabilization (i.e. including the contribution from carbon, neon as well as deuterium ions) which is used in the criterion to determine when the calculated linear growth rates of PBM are unstable. Consequently, the new ELITE computed PBM boundaries were more consistent with the operating points than when only deuterium was included. This in turn suggests that the impurity may help to improve pedestal pressure through affecting ion diamagnetic frequency in the pedestal region, which could positively lead to the ballooning stability boundary extension.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Evaluation of silicon carbide as a divertor armor material in DIII-D H-mode discharges

Silicon carbide (SiC) represents a promising but largely untested plasma-facing material (PFM) for next-step fusion devices. In this work, an analytic mixed-material erosion model is developed by calculating the physical (via SDTrimSP) and chemical (via empirical scalings) sputtering yield from SiC, Si, and C. The Si content in the near-surface SiC layer is predicted to increase during D plasma bombardment due to more efficient physical and chemical sputtering of C relative to Si. Silicon erosion from SiC thereby occurs primarily from sputtering of the enriched Si layer, rather than directly from the SiC itself. SiC coatings on ATJ graphite, manufactured via chemical vapor deposition, were exposed to repeated H-mode plasma discharges in the DIII-D tokamak to test this model. The qualitative trends from analytic modeling are reproduced by the experimental measurements, obtained via spectroscopic inference using the S/XB method. Quantitatively the model slightly under-predicts measured erosion rates, which is attributed to uncertainties in the ion impact angle distribution, as well as the effect of edge-localized modes. After exposure, minimal changes to the macroscopic or microscopic surface morphology of the SiC coatings were observed. Compositional analysis reveals Si enrichment of about 10%, in line with expectations from the erosion model. Extrapolating to a DEMO-type device, an order-of-magnitude decrease in impurity sourcing, and up to a factor of 2 decrease in impurity radiation, is expected with SiC walls, relative to graphite, if low C plasma impurity content can be achieved. Furthermore, these favorable erosion properties motivate further investigations of SiC as a low-Z, non-metallic PFM.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Impact of toroidal magnetic field direction on integrated ELM-stable operation and divertor power exhaust via boron powder injection in EAST

We report the first in-depth comparison of the impact of toroidal magnetic field direction on solid boron injection used for Edge-Localized Mode (ELM) control, power exhaust, and core high-Z impurity control in the Experimental Advanced Superconducting Tokamak. With favorable ion ∇B drift towards the upper X-point in an upper-single-null configuration, boron injection effectively suppresses ELMs, produces a detachment of the inner divertor target, and leads to improved energy confinement. ELM suppression in this configuration is accompanied by the excitation of an Edge Harmonic Mode. In contrast, with unfavorable ion ∇B drift away from the upper X-point, boron injection also suppresses ELMs but leads to a more symmetric detachment state of both the inner and outer divertor targets, while plasma energy confinement is slightly degraded despite similar boron injection levels; a different low-frequency coherent mode without multiple harmonics is observed. Measurements from toroidally separated views show that the divertor response to boron injection is essentially toroidally symmetric, supporting the use of two-dimensional SOLPS-ITER modeling with a toroidally uniform impurity source. These experimental observations are qualitatively consistent with SOLPS-ITER simulations, which highlight the critical role of E × B drift effects in setting the Bt-dependent in–out asymmetry of detachment and in asymmetrically transporting particles and injected impurities within the scrape-off layer and private-flux region. These findings underscore the importance of drift physics and real-time wall conditioning in controlling low-Z impurity transport and optimizing edge solutions for integrated, ELM-stable, high-performance tokamak operation.

E × B drift↗
DOE OSTI2024

Overview of recent experimental results on the EAST Tokamak

Since the last IAEA-FEC in 2021, significant progress on the development of long pulse steady state scenario and its related key physics and technologies have been achieved, including the reproducible 403 s long-pulse steady-state H-mode plasma with pure radio frequency (RF) power heating. A thousand-second time scale (~1056 s) fully non-inductive plasma with high injected energy up to 1.73 GJ has also been achieved. The EAST operational regime of high β P has been significantly extended (H 98y2 > 1.3, β P ~ 4.0, β N ~ 2.4 and n e /n GW ~ 1.0) using RF and neutral beam injection (NBI). The full edge localized mode suppression using the n = 4 resonant magnetic perturbations has been achieved in ITER-like standard type-I ELMy H-mode plasmas with q 95 ≈ 3.1 on EAST, extrapolating favorably to the ITER baseline scenario. The sustained large ELM control and stable partial detachment have been achieved with Ne seeding. The underlying physics of plasma-beta effect for error field penetration, where toroidal effect dominates, is disclosed by comparing the results in cylindrical theory and MARS-Q simulation in EAST. Breakdown and plasma initiation at low toroidal electric fields (<0.3 V m -1 ) with EC pre-ionization is developed. A beneficial role on the lower hybrid wave injection to control the tungsten concentration in the NBI discharge is observed for the first time in EAST suggesting a potential way toward steady-state H-mode NBI operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Metrics and extrapolation of resonant magnetic perturbation thresholds for ELM suppression

This large database study of resonant magnetic perturbation (RMP) edge localized mode (ELM) suppression thresholds in the AUG, DIII-D, EAST, and KSTAR tokamaks details the key strengths and weaknesses of RMP metrics. The RMP ELM suppression database used for this work contains plasma information at the time of transition from ELMing to ELM suppressed states where a clear experimental threshold is identified. The experimental threshold distributions are compared for five metrics: (1) the island overlap width, (2) pedestal top Chirikov overlap, (3) peeling edge displacement, (4) pedestal top resonant drive, and (5) edge dominant mode overlap. The distributions, the regularity of the dependence on RMP coil currents, and the sensitivities of a given metric to equilibrium reconstruction details are compared. The overlap metric proves to be a good compromise between including the appropriate plasma response physics and maintaining a numerical robustness. This quantity does not exhibit clear power-law scalings for projection, but machine learning can assist in predicting thresholds within the existing parameter ranges and providing uncertainty quantification of those predictions. Two new first-principles models, one utilizing a threshold from the non-linear Modified Rutherford equation evaluated at the pedestal top and one utilizing the SLAYER code to calculate the linear tearing threshold from torque balance, offer possible paths to extrapolation beyond the existing database parameter space.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Control of neutral fueling and helium exhaust to NSTX-U plasmas by means of three-dimensional magnetic control fields

Resonant magnetic perturbations are used to stabilize plasma edge instabilities, so-called edge localized modes (ELMs), in high-performance (H-mode) plasmas explored for fusion energy. These ELMs cause repetitive outburst of confined energy and particles and cause cyclic loading of plasma facing components (PFCs). This endangers the integrity of the PFCs and hence limits the lifetime and hence commercial viability of fusion. It was shown that these ELMs can be stabilized by application of small amplitude resonant magnetic perturbation (RMP) fields. This removes the ELMs as edge instabilities but also induces three-dimensional (3D) effects to the plasma boundary, which was formerly toroidally axisymmetric. The impact of this 3D perturbation on the plasma boundary solution needs to be understood to extrapolate the effects to ITER and towards a fusion reactor, if ELM control by RMP fields would be utilized.

3D Boundary Plasmas↗
DOE OSTI2023

Effect of aspect ratio on plasma response to resonant magnetic perturbations in tokamak devices

A systematic numerical study is carried out, computing and comparing the plasma response to the resonant magnetic perturbation (RMP) field, applied for controlling edge localized modes (ELMs), in a series of tokamak plasmas with varying aspect ratio and utilizing the MARS-F code. The aspect ratio is scanned either by varying the plasma major radius at a fixed minor radius or by varying the latter while fixing the former. Both approaches yield similar results when compared in terms of quantities with proper normalizations. In general, a non-monotonic dependence of the resonant response field (normalized by the vacuum counterpart) near the plasma edge is found with varying aspect ratio, indicating that a given ELM control coil current configuration strongly favors plasmas with a certain aspect ratio. This optimal aspect ratio, on the other hand, depends on the toroidal as well as poloidal (i.e., coil phasing) spectra of the applied RMP field. The equilibrium (edge) safety factor, the plasma shape, and the plasma toroidal flow are all fixed to ensure that the effects identified here are predominantly due to the plasma aspect ratio.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

LLNL FESP Theory Highlights: August 2024

The 2024 ABOUND SciDAC and BOUT++ combined workshop was held August 5-9 th 2024 at the University of California Livermore Collaboration Center (UCLC) in Livermore. Bringing together leading scientists and researchers from across the globe, this pivotal event focused on advancing plasma physics and boundary plasma dynamics within the context of fusion energy research. Key discussions throughout the meeting highlighted significant advancements in the BOUT++ framework, including enhanced simulations of small Edge Localized Modes (ELMs) and the initiation of integrating the integration of the 5D GEM gyrokinetic turbulence core code with the 2D SOLPS-ITER boundary transport code. These developments are crucial for managing heat loads in fusion reactors and supporting the longevity of plasma-facing components. The event also featured a session on Inter-SciDAC Collaborations, where principal investigators from multiple U.S. FES SciDAC tokamak projects explored opportunities for cross-collaboration. Additionally, the meeting showcased cutting-edge advancements in GPU acceleration and AI/ML technologies, poised to drive the next generation of fusion research. In his closing remarks, Dr. Xueqiao Xu emphasized the importance of the collaborative efforts and discussions that took place, noting their potential to shape future breakthroughs in fusion energy. The event underscored the global nature of the BOUT++ collaboration, with contributions from over 57 institutions worldwide. The 2024 BOUT++ and ABOUND Joint Hybrid Meeting continues to drive forward the research and innovations needed to achieve fusion energy, setting the stage for future collaboration and discovery.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Type-I ELM mitigation by continuous lithium granule gravitational injection into the upper tungsten divertor in EAST

Large edge-localized modes (ELMs) were mitigated by gravitational injection of lithium granules into the upper X-point region of the experimental advanced superconducting tokamak (EAST) device with tungsten plasma-facing components. The maximum ELM size was reduced by ~70% in high β N H-mode plasmas. Large ELM stabilization was sustained for up to about 40 energy confinement times, with constant core radiated power and no evidence of high-Z or low-Z impurity accumulation. The lithium granules injection reduced the edge plasma pedestal density and temperature and their gradients, due to increased edge radiation and reduced recycling from the plasma-facing components. Ideal stability calculations using the ELITE code indicate that the stabilization of large ELMs correlates with improved stability of intermediate-n peeling-ballooning modes, due to reduced edge current resulting from the profile changes. The pedestal pressure reduction was partially offset by a core density increase, which resulted in a modest ~7% drop in core stored energy and normalized energy confinement time. We surmise that the remnant small ELMs are triggered by the penetration of multiple Li granules just past the separatrix, similar to small ELMs triggered by deuterium pellet Futatani et al (2014 Nucl. Fusion 54 073008). This study extends previous ELM elimination with Li powder injection Maingi et al (2018 Nucl. Fusion 58 024003) in EAST because (1) use of small, dust-like powder and the related potential health hazards were eliminated, and (2) use of macroscopic granules should be more applicable to future devices, due to deeper penetration than dust particles, e.g. inside the separatrix with velocities ~10 m s -1 in EAST.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗