Search NASA⌕ Search

SEARCH · Search NASA

Results for “effective kinetics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Development of the Monolith Froth Reactor for Catalytic Wet Oxidation of CELSS Model Wastes

The aqueous phase oxidation of acetic acid, used as a model compound for the treatment of CELSS (Controlled Ecological Life Support System) waste, was carried out in the monolith froth reactor which utilizes two-phase flow in the monolith channels. The catalytic oxidation of acetic acid was carried out over a Pt/Al2O3 catalyst, prepared at The University of Tulsa, at temperatures and pressures below the critical point of water. The effect of externally controllable parameters (temperature, liquid flow rate, distributor plate orifice size, pitch, and catalyst distance from the distributor plate) on the rate of acetic acid oxidation was investigated. Results indicate reaction rate increased with increasing temperature and exhibited a maximum with respect to liquid flow rate. The apparent activation energy calculated from reaction rate data was 99.7 kJ/mol. This value is similar to values reported for the oxidation of acetic acid in other systems and is comparable to intrinsic values calculated for oxidation reactions. The kinetic data were modeled using simple power law kinetics. The effect of "froth" feed system characteristics was also investigated. Results indicate that the reaction rate exhibits a maximum with respect to distributor plate orifice size, pitch, and catalyst distance from the distributor plate. Fundamental results obtained were used to extrapolate where the complete removal of acetic acid would be obtained and for the design and operation of a full scale CELSS treatment system.

Abraham, Martin↗
NASA NTRS2022

Effect of Sulfur on siderophile element partitioning between olivine and martian mantle primary melt

Ni and Co variations in primary martian magmas exhibit anomalous incompatible behavior, which has remained an unexplained conundrum. Because martian magmas are S-rich, and some trace metals are reported to have enhanced solubility in S-bearing magmas, we have carried out a series of experiments to evaluate the effect of high-S melts on the olivine/melt partitioning of Ni, Co, Mn, V, and Cr. Near-liquidus experiments on a synthetic primary martian mantle melt (Yamato-980459 [Y98]) were completed in a piston-cylinder apparatus at 0.75 GPa. Previous studies in S-free systems illustrate that the partition coefficients for these elements are dependent chiefly on D(Mg(Ol/melt)) (the partition coefficient defined as wt% Mg in olivine/wt% Mg in melt, a proxy for temperature), and were used to calibrate a predictive expression that includes the effects of temperature [i.e., D(Mg(Ol/melt))], melt composition, and oxygen fugacity. These predictive expressions are then used to isolate any effect in DM olivine/melt due to dissolved sulfur. The results show that S might have a small effect for Co, but not enough to change Co partitioning from compatible to incompatible in our experiments. The addition of a sulfur term to the D(Co) predictive expressions shows that nearly 8000 ppm of sulfur would be required in the melt (at liquidus temperature of Y98) for D(Co) to become <1. These S contents are two times higher than those of a sulfide-saturated melt at the P-T conditions of a martian mantle source region. Therefore, the anomalous incompatible behavior observed in these primary magma suites must be due to another mechanism. High temperature, oxygen fugacity, and diffusion are not viable mechanisms, but magma mixing, assimilation, or kinetic crystallization effects remain possibilities.

shergottite↗
NASA NTRS1981

Chemical kinetic analysis of hydrogen-air ignition and reaction times

An anaytical study of hydrogen air kinetics was performed. Calculations were made over a range of pressure from 0.2 to 4.0 atm, temperatures from 850 to 2000 K, and mixture equivalence ratios from 0.2 to 2.0. The finite rate chemistry model included 60 reactions in 20 species of the H2-O2-N2 system. The calculations also included an assessment of how small amounts of the chemicals H2O, NOx, H2O2, and O3 in the initial mixture affect ignition and reaction times, and how the variation of the third body efficiency of H2O relative of N2 in certain key reactions may affect reaction time. The results indicate that for mixture equivalence ratios between 0.5 and 1.7, ignition times are nearly constant; however, the presence of H2O and NO can have significant effects on ignition times, depending on the mixture temperature. Reaction time is dominantly influenced by pressure but is nearly independent of initial temperature, equivalence ratio, and the addition of chemicals. Effects of kinetics on reaction at supersonic combustor conditions are discussed.

Rogers, R. C.↗
NASA NTRSDate not supplied

Constraints on triple oxygen isotope kinetics

Triple oxygen isotope measurements have been used as tracers for classifying meteorites, as indicators of atmospheric chemistry and as a proxy for primary productivity among other uses. These utilities rely on the mass dependency of most chemical reactions: δ17O is proportional to δ18O by roughly a factor of 0.5. However,in detail it is known that mass-dependency factorsvary. Constraints on mass dependency are well established for equilibrium isotope effects, but similar constraints for kinetic isotope effects are lacking.Here, we provide constraints for isotope effects generated by unidirectional chemical reactions (i.e. kinetic isotope effects, KIEs). A simplified Monte Carlo model is used to estimatethe range of kinetic isotope effects. It is found that the range of KIEs exceeds the range of equilibrium isotope effects such that some mass dependent kinetic isotope effects could be mistaken for being mass-independent. For the16O-17O-18O system,Δ′17Ovariations as large 0.8‰ can be generated from a single reaction step. Two case studies from published literature, on the thermal decomposition of calcite (CaCO3) and brucite (Mg(OH)2), are used to test the extreme limits of the modeled results. Isotope fractionationsgenerated fromdensity functional theory models of the surface reaction steps are shownto match the published data. The fractionation models are strictly mass dependent thus this result suggests thermal decomposition of calcite is also mass dependent. Although oxygen is the focus here, our approach applies to any system with more than two isotopes.

J. A. Hayles↗
NASA NTRS1981

Vertical transport and photochemistry in the terrestrial mesosphere and lower thermosphere /50-120 km/

A study is conducted of the coupled effects of kinetics, solar cycle flux variations, and vertical transport on the distribution of long-lived hydrogen-carbon-oxygen compounds in the terrestrial mesosphere and lower thermosphere, using a one-dimensional aeronomy model. The calculations account for the important chemical reactions and use rocket measurements of the solar flux at solar minimum and maximum. Photodissociation rates appropriate for the mesosphere are determined with a spherical shell atmosphere formalism. Detailed corrections for the O2 Schumann-Runge bands and the temperature dependence of the CO2 cross sections are used. An eddy diffusion profile is derived which is in agreement with the Aladdin 74 mass spectral measurements of atomic O, O2, CO2, and Ar in the lower thermosphere and observations of the O3 minimum at about 80 km.

Allen, M.↗
NASA NTRS1950

The Effect of Ice Formations on Propeller Performance

Measurements of propeller efficiency loss due to ice formation are supplemented by an analysis to establish the magnitude of efficiency losses to be anticipated during flight in icing conditions. The measurements were made during flight in natural icing conditions; whereas the analysis consisted of an investIgation of changes in blade-section aerodynamic characteristics caused by ice formation and the resulting propeller efficiency changes. Agreement in the order of magnitude of eff 1- ciency losses to be expected is obtained between measured and analytical results. The results indicate that, in general, efficiency losses can be expected to be less than 10 percent; whereas maximum losses, which will be encountered only rarely, may be as high as 15 or 20 percent. Reported. losses larger than 15 or 20 percent, based on reductions in airplane performance, probably are due to ice accretions on other parts of the airplane. Blade-element theory is used in the analytical treatment, and calculations are made to show the degree to which the aerodynamic characteristics of a blade section. must be altered to produce various propeller efficiency losses. The effects of ice accretions on airfoil-section characteristics at subcritical speeds and their influence on drag-divergence Mach number are examined, and. the attendant maximum efficiency losses are computed. The effect of kinetic heating on the radial extent of ice formation is considered, and its influence on required length of blade heating shoes is discussed. It is demonstrated how the efficiency loss resulting from an icing encounter is influenced by the decisions of the pilot in adjusting the engine and propeller controls.

Neel, C. B., Jr.↗
NASA NTRS1986

Investigations of toughening mechanisms of epoxy resins

Composite material technology was applied to the solid rocket booster by the development of a carbon filament-epoxy resin case which yields a net increase of 4000 lbs. in payload in the shuttle. The question of reusability of the new composite tanks has not yet been answered and will depend on the toughness of the matrix resin. The present study was aimed at providing conditions whereby test specimens of the epoxy resin (EPON/85) and curing agents of systematically varied structures could be produced in a controlled manner. Three sets of conditions were found that might allow the isolation of the structural effects on toughness from the cure effects. The kinetic methods leading to the determination of these conditions are described.

Koenig, T.↗
NASA NTRS1987

Theoretical performance of hydrogen-bromine rechargeable SPE fuel cell

A mathematical model was formulated to describe the performance of a hydrogen-bromine fuel cell. Porous electrode theory was applied to the carbon felt flow-by electrode and was coupled to theory describing the solid polymer electrolyte (SPE) system. Parametric studies using the numerical solution to this model were performed to determine the effect of kinetic, mass transfer, and design parameters on the performance of the fuel cell. The results indicate that the cell performance is most sensitive to the transport properties of the SPE membrane. The model was also shown to be a useful tool for scale-up studies.

Savinell, Robert F.↗
NASA NTRS1988

Laminar diffusion flames under micro-gravity conditions

Laminar methane and propane gas-jet diffusion flames have been theoretically and experimentally studied at NASA-Lewis under microgravity conditions. It is noted that laminar diffusion flames are strongly affected by the combined effects of kinetics, radiation, and such transient phenomena as flame ignition, stabilization, and extinction. Observations on the distinctive nature of the flame color and luminosity parameters in microgravity are presented, and flame behavior under transient, high-deceleration rates is discussed. Test hardware and instrumentation design are described.

Edelman, Raymond B.↗
NASA NTRS1988

Theoretical performance of hydrogen-bromine rechargeable SPE fuel cell

A mathematical model was formulated to describe the performance of a hydrogen-bromine fuel cell. Porous electrode theory was applied to the carbon felt flow-by electrode and was coupled to theory describing the solid polymer electrolyte (SPE) system. Parametric studies using the numerical solution to this model were performed to determine the effect of kinetic, mass transfer, and design parameters on the performance of the fuel cell. The results indicate that the cell performance is most sensitive to the transport properties of the SPE membrane. The model was also shown to be a useful tool for scale-up studies.

Savinell, R. F.↗
NASA NTRS1987

Arcjet thruster research and technology. Phase 1: Executive summary

The principal objective of this two phase program is to conduct the development research required to make the low power arcjet a flight ready technology. Many important results were obtained during Phase 1 to move closer to this objective. Fundamental analyses were performed of the arcjet nozzle, the gas kinetic reaction effects, the thermal environment, and the arc stabilizing vortex. These aided the conceptual understanding of the arcjet and guided design work. A hydrazine (N2H4) arcjet was designed that combined a flight qualified catalyst bed with a modular arcjet. Extensive testing was performed which demonstrated the feasibility of using this propellant in an arcjet for the first time. Startup techniques were developed, stability maintained, material compatibility tests conducted, and performance mapping tests performed. Specific impulse values from 400 to 730 seconds were produced with a non-optimized design. These levels are higher than were originally thought possible and proved that extremely high enthalpy values can be obtained with constricted arc technology. Erosion rate data are promising for lifetime extensions to meet flight application requirements. Power control unit (PCU) development was started with the design and fabrication of a laboratory high switching frequency supply. Valuable data were obtained on PCU operation and on the interaction with the dynamic arc. Phase 2 efforts presently underway are resolving key issues for multi-hundred hour lifetimes, are continuing to investigate arcjet/PCU interactions, and will demonstrate duty cycle N2H4 arcjet/PCU operation in a simulated flight mode for lifetimes consistent with initial applications.

Source record↗
NASA NTRS1990

Upcoming planetary missions and the applicability of high temperature superconductor bolometers

Planetary missions to Mars and beyond can last 11 years and longer, making impractical the use of stored cryogens. Passive radiative coolers and single-stage mechanical coolers remain possibilities. CRAF and CASSINI, both using the newly developed Mariner Mark 2 spacecraft, will be the next outer planet missions after Galileo; they are intended to provide information on the origin and evolution of the solar system. CRAF is a cometary rendezvous mission slated for a 1994 launch. CASSINI has been chosen by ESA and will be launched by a Titan 4/Centaur in 1996. It will fly by Jupiter in 2000, inject an ESA-supplied probe into Titan in 2002, and take data in Saturn orbit from 2002 to 2006. NASA/Goddard is currently developing a prototype Fourier transform spectrometer (CIRS) that will be proposed for the CASSINI mission. The baseline infrared detectors for CIRS are HgCdTe to 16 microns and Schwarz-type thermopiles from 16 to 1000 microns. The far infrared focal plane could be switched from thermopiles to high temperature superconductor (HTS) bolometers between now and 1996. An HTS bolometer could be built using the kinetic inductance effect, or the sharp resistance change at the transition. The transition-edge bolometer is more straightforward to implement and initial efforts at NASA/Goddard are directed to that device. A working device was made and tested in early 1989. It also has somewhat elevated noise levels below 100 Hz. Upcoming efforts will center on reducing the time constant of the HTS bolometer by attempting to deposit an HTS film on a diamond substrate, and by thinning SrTiO3 substrates. Attempts will be made to improve the film quality to reduce th 1/f noise level, and to improve the thermal isolation to increase the bolometer sensitivity. An attempt is being made to deposit good-quality HTS films on diamond films using an MOCVD technique.

Brasunas, J.↗
NASA NTRS1991

Profiles of alpha 13 C and alpha D in methane from the lower stratosphere

Methane is an important greenhouse gas of biogenic and anthropogenic origin for which global budgets are being constructed from a variety of data. One approach to the global methane budget is the use of the stable isotopes C-13 and D, and the radionuclide C-14 as tracers. The authors measured the isotopic composition of methane from various sources and in tropospheric air for a number of locations. Here, the authors report on the isotopic composition of methane from the lower stratosphere. Measurements of this concentration in the stratosphere can yield estimates for the kinetic isotope effects in the methane destruction reactions. These effects have to be known for quantitative isotopic methane budgets.

Wahlen, Martin↗
NASA NTRS1990

The reaction efficiency of thermal energy oxygen atoms with polymeric materials

The reaction efficiency of several polymeric materials with thermal-energy (0.04 eV translational energy), ground-state (O3P) oxygen atoms was determined by exposing the materials to a room temperature gas containing a known concentration of atomic oxygen. The reaction efficiency measurements were conducted in two flowing afterglow systems of different configuration. Atomic oxygen concentration measurements, flow, transport and surface dose analysis is presented in this paper. The measured reaction efficiencies of Kapton, Mylar, polyethylene, D4-polyethylene and Tedlar are .001 to .0001 those determined with high-energy ground-state oxygen atoms in low earth orbit or in a high-velocity atom beam. D4-polyethylene exhibits a large kinetic isotope effect with atomic oxygen at thermal but not hyperthermal atom energies.

Koontz, S. L.↗
NASA NTRS1990

Superconductivity applications for infrared and microwave devices; Proceedings of the Meeting, Orlando, FL, Apr. 19, 20, 1990

Various papers on superconductivity applications for IR and microwave devices are presented. The individual topics addressed include: pulsed laser deposition of Tl-Ca-Ba-Cu-O films, patterning of high-Tc superconducting thin films on Si substrates, IR spectra and the energy gap in thin film YBa2Cu3O(7-delta), high-temperature superconducting thin film microwave circuits, novel filter implementation utilizing HTS materials, high-temperature superconductor antenna investigations, high-Tc superconducting IR detectors, high-Tc superconducting IR detectors from Y-Ba-Cu-O thin films, Y-Ba-Cu0-O thin films as high-speed IR detectors, fabrication of a high-Tc superconducting bolometer, transition-edge microbolometer, photoresponse of YBa2Cu3O(7-delta) granular and epitaxial superconducting thin films, fast IR response of YBCO thin films, kinetic inductance effects in high-Tc microstrip circuits at microwave frequencies.

Bhasin, Kul B.↗
NASA NTRS1991

Upcoming planetary missions and the applicability of high temperature superconductor bolometers

Planetary missions to Mars and beyond can last 11 years and longer, making impractical the use of stored cryogens. Passive radiative coolers and single-stage mechanical coolers remain possibilities. Cassini and Comet Rendezvous/Asteroid Fly-by (CRAF), both using the newly developed Mariner Mark 2 spacecraft, will be the next outer planet missions after Galileo; they are intended to provide information on the origin and evolution of the solar system. CRAF is slated for a 1994 launch. Cassini was chosen by ESA and will be launched by a Titan 4/Centaur in 1996. It will fly by Jupiter in 2000, inject an ESA-supplied probe into Titan in 2002, and take data in Saturn's orbit from 2002 to 2006. NASA/Goddard is currently developing a prototype Fourier transform spectrometer, the Composite Infrared Spectrometer (CIRS), for the Cassini mission. The baseline infrared detectors for CIRS are HgCdTe to 16 microns and Schwarz-type thermopiles from 16 to 1000 microns. The far infrared focal plane could be switched from thermopiles to high temperature superconductor (HTS) bolometers between now and 1996. An HTS bolometer could be built using the kinetic inductance effect, or the sharp resistance change at the transition. The transition-edge bolometer is more straightforward to implement, and initial efforts at NASA/Goddard are directed to that device. A working device was made and tested in early 1989. It also has somewhat elevated noise levels below 100 Hz. Upcoming efforts will center on reducing the time constant of the HTS bolometer by attempting to deposit an HTS film on a diamond substrate, and by thinning SrTiO3 substrates. Attempts will be made to improve the film quality to reduce the 1/4 noise level, and to improve the thermal isolation to increase the bolometer sensitivity. An attempt is being made to deposit good-quality HTS films on diamond films using a metal-organic chemical vapor deposition (MOCVD) technique.

Brasunas, J.↗
NASA NTRS1992

CH4 production via CO2 reduction in a temperate bog - A source of (C-13)-depleted CH4

The paper reports measurements, taken over two annual cycles, of the flux and delta(C-13) of CH4 released from an acidic peat bog located in the foothills of the Cascade Range in Washington state, U.S. Measurements of the rate of aceticlastic methanogenesis and CO2 reduction in peat soil, using (C-14)-labeled acetate and sodium bicarbonate, show that acetate was not an important CH4 precursor and that CO2 reduction could account for all of the CH4 production. The in situ kinetic isotope effect for CO2 reduction, calculated using the delta-(C-13) of soil water CO2 and CH4 flux, was 0.932 +/- 0.007.

Lansdown, J. M.↗