Search NASA⌕ Search

SEARCH · Search NASA

Results for “elasticity coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 163 records · Page 9

Rapid Nb 3 Sn film growth by sputtering Nb on hot bronze

Nb deposited by magnetron sputtering onto hot Cu-15 wt.%Sn bronze substrates at temperatures above 700 °C achieved Nb 3 Sn film growth at a rate of 33 nm min -1 , which was an order of magnitude faster than that achieved for deposition of Nb on bronze at low temperature followed by in situ post reaction at the same high temperatures. Tin content in the Nb 3 Sn films made on hot bronze was ~26.3%, which is significantly higher than ~24.5% obtained by post-reaction as well as for typical bulk reactions between Nb and α -bronze. The Nb 3 Sn lattice parameter was consistent with measured tin content and predicted elastic strain for both routes. Critical temperatures of 14 K–16 K, instead of 18 K, were consistent with elastic strain due to coefficient of thermal expansion mismatch between the Nb 3 Sn and bronze substrate and, for the hot-bronze samples, stress related to the growth mechanism. Films were fully coalesced and had surface roughness values <20 nm over a 100 μ m 2 scan. Grain structure of the Nb 3 Sn films produced by Nb sputtering on hot bronze resembles zone 2 in the Thornton structure-zone diagram, in contrast to the equiaxed grain structure reminiscent of microstructure observed in reacted Nb 3 Sn wires exhibited by the post-reaction route.

Physics↗

Variation of the {sup 13}C Diamond Properties under Isothermal Compression

The parameters of atomic interaction pair potential for {sup 13}C diamond have been determined from experimental data on the ratio of Raman frequencies for isotopically different diamonds. Based on these parameters, an equation of state and baric dependences of {sup 13}C diamond lattice properties at 300 K have been calculated. Specifically, the Debye temperature; the first, second, and third Grüneisen parameters; elastic modulus; thermal expansion coefficient; heat capacity; surface energy; and pressure derivatives of these parameters along a 300 K isotherm have been determined. The results have been compared with available data for diamond having a natural isotopic composition, i.e., for {sup 12.01}C.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

MC3, Version 1

The MC3 code is used to perform Monte Carlo simulations in the isothermal-isobaric ensemble (constant number of particles, temperature, and pressure) on molecular crystals. The molecules within the periodic simulation cell are treated as rigid bodies, alleviating the requirement for a complex interatomic potential. Intermolecular interactions are described using generic, atom-centered pair potentials whose parameterization is taken from the literature [D. E. Williams, J. Comput. Chem., 22, 1154 (2001)] and electrostatic interactions arising from atom-centered, fixed, point partial charges. The primary uses of the MC3 code are the computation of i) the temperature and pressure dependence of lattice parameters and thermal expansion coefficients, ii) tensors of elastic constants and compliances via the Parrinello and Rahman’s fluctuation formula [M. Parrinello and A. Rahman, J. Chem. Phys., 76, 2662 (1982)], and iii) the investigation of polymorphic phase transformations. The MC3 code is written in Fortran90 and requires LAPACK and BLAS linear algebra libraries to be linked during compilation. Computationally expensive loops are accelerated using OpenMP.

Cawkwell, MarcJon↗

Atomistic and mesoscale simulations to determine effective diffusion coefficient of fission products in SiC

The silicon carbide (SiC) layer in tristructural isotropic (TRISO) particles serves as the barrier to prevent escape of fission products produced in the fuel kernel. Knowing the diffusion coefficient of fission products through SiC is critical to determining whether fission gas can escape from the particle. It has been observed in experiments that Ag accumulated in grain boundaries and triple junctions in SiC. It is hypothesized that grain boundary diffusion is the primary pathway by which fission products penetrate the SiC layer. In this report, the effective diffusion coefficient of the fission product Ag through the grain boundary network is calculated using a combination of atomistic and phase-field methods. The grain boundary diffusion coefficient is calculated using molecular dynamics simulations. The bulk diffusion coefficient is determined using a combination of density functional theory and nudged elastic band methods. An effective diffusion coefficient is calculated, accounting for the grain structure using a phase-field method. The effective diffusion coefficient will be incorporated into Bison and fission product release calculations are compared to available experimental data.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Developing Machine Learning Interatomic Potential for Fe-Cr-Ni Alloys

Accurate prediction of creep and fatigue behavior of stainless steel at elevated temperatures in hydrogen environment requires fundamental understanding of alloy-hydrogen interaction at cross-scale including bulk lattice and key defects such as vacancies, grain boundaries, surfaces, stacking faults, dislocations, and precipitates. This project aims to predict creep behavior of 347H stainless steel with H using machine learning interatomic potentials based on first-principles density functional theory simulations. The Moment Tensor Potentials platform is adopted for this work since it demonstrates a fine balance between model accuracy and computational efficiency. The potential is well trained based on large amount of high-fidelity density functional theory calculations. The validation is carried out by comparing various important properties including short range order, coefficient of thermal expansion, elastic properties, stacking fault energy, grain boundary energy, and surface energy. This work lays the foundation for reliable atomistic simulation of high temperature hydrogen attack of stainless steel.

density functional theory (DFT)↗

Carbon Characterization Laboratory Report

The newly completed Idaho National Laboratory (INL) Carbon Characterization Laboratory (CCL) is located in Lab-C20 of the Idaho National Laboratory Research Center. This laboratory was established under the Next Generation Nuclear Plant (NGNP) Project to support graphite research and development activities. The CCL is designed to characterize and test carbon-based materials such as graphite, carbon-carbon composites, and silicon-carbide composite materials. The laboratory is fully prepared to measure material properties for nonirradiated carbon-based materials. Plans to establish the laboratory as a radiological facility within the next year are definitive. This laboratory will be modified to accommodate irradiated materials, after which it can be used to perform material property measurements on both irradiated and nonirradiated carbon-based material. Instruments, fixtures, and methods are in place for preirradiation measurements of bulk density, thermal diffusivity, coefficient of thermal expansion, elastic modulus, Young’s modulus, Shear modulus, Poisson ratio, and electrical resistivity. The measurement protocol consists of functional validation, calibration, and automated data acquisition.

36 MATERIALS SCIENCE↗

Application of Multiharmonic QCM-D for Detection of Plasmin at Hydrophobic Surfaces Modified by β-Casein

Plasmin protease plays an important role in many processes in living systems, including milk. Monitoring plasmin activity is important for control of the nutritional quality of milk and other dairy products. We designed a biosensor to detect the proteolytic activity of plasmin, using multiharmonic quartz crystal microbalance with dissipation (QCM-D). The β-casein immobilized on the hydrophobic surface of 1-dodecanethiol on the AT-cut quartz crystal was used to monitor plasmin activity. We demonstrated detection of plasmin in a concentration range of 0.1–20 nM, with the limit of detection about 0.13 ± 0.01 nM. The analysis of viscoelastic properties of the β-casein layer showed rapid changes of shear elasticity modulus, μ, and coefficient of viscosity, η, at plasmin sub-nanomolar concentrations, followed by modest changes at nanomolar concentrations, indicating multilayer architecture β-casein. A comparative analysis of viscoelastic properties of β-casein layers following plasmin and trypsin cleavage showed that the higher effect of trypsin was due to larger potential cleavage sites of β-casein.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Identification of Integral Benchmarks for Nuclear Data Testing Using DICE (Database for the International Handbook of Evaluated Criticality Safety Benchmark Experiments)

Typical users of the International Criticality Safety Evaluation Project (ICSBEP) Handbook have specific criteria to which they desire to find matching experiments. Depending on the application, those criteria may consist of any combination of physical or chemical characteristics and/or various neutronic parameters. The ICSBEP Handbook contains a structured format helping the user narrow the search for experiments of interest. However, with nearly 4300 different experimental configurations and the ever increasing addition of experimental data, the necessity to perform multiple criteria searches have rendered these features insufficient. As a result, a relational database was created with information extracted from the ICSBEP Handbook. A users’ interface was designed by OECD and DOE to allow the interrogation of this database. The database and the corresponding users’ interface are referred to as DICE. DICE currently offers the capability to perform multiple criteria searches that go beyond simple fuel, physical form and spectra and includes expanded general information, fuel form, moderator/coolant, neutron-absorbing material, cladding, reflector, separator, geometry, benchmark results, spectra, and neutron balance parameters. DICE also includes the capability to display graphical representations of neutron spectra, detailed neutron balance, sensitivity coefficients for capture, fission, elastic scattering, inelastic scattering, nu-bar and mu-bar, as well as several other features.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A monostrain test apparatus

Test apparatus is designed for determining tensile strength, modulus of elasticity, elongation, and thermal coefficient of contraction or expansion of uniformly shaped plastics, adhesives, and foam materials over temperature range of 700 to 90 K (800 to -300). Tests may be used in design quality control, and in evaluation of new adhesives and plastic materials.

Helf, J. C.↗

Work function measurements by the field emission retarding potential method

Using the field emission retarding potential method true work functions have been measured for the following monocrystalline substrates: W(110), W(111), W(100), Nb(100), Ni(100), Cu(100), Ir(110) and Ir(111). The electron elastic and inelastic reflection coefficients from several of these surfaces have also been examined near zero primary beam energy.

Swanson, L. W.↗

Work function measurements by the field emission retarding potential method.

Description of the theoretical foundation of the field electron retarding potential method, and review of its experimental application to the measurement of single crystal face work functions. The results obtained from several substrates are discussed. An interesting and useful fallout from the experimental approach described is the ability to accurately measure the elastic and inelastic reflection coefficient for impinging electrons to near zero-volt energy.

Strayer, R. W.↗

Friction and morphology of magnetic tapes in sliding contact with nickel-zinc ferrite

Friction and morphological studies were conducted with magnetic tapes containing a Ni-Zn ferrite hemispherical pin in laboratory air at a relative humidity of 40 percent and at 23 C. The results indicate that the binder plays a significant role in the friction properties, morphology, and microstructure of the tape. Comparisons were made with four binders: nitrocellulose; poly (vinyledene) chloride; cellulose acetate; and hydroxyl-terminated, low molecular weight polyester added to the base polymer, polyester-polyurethane. The coefficient of friction was lowest for the tape with the nitrocellulose binder and increased in the order hydroxylterminated, low molecular weight polyester resin; poly (vinyledene) chloride; and cellulose acetate. The degree of enclosure of the oxide particles by the binder was highest for hydroxyl-terminated, low molecular weight polyester and decreased in the order cellulose acetate, poly (vinyledene) chloride, and nitrocellulose. The nature of deformation of the tape was a factor in controlling friction. The coefficient of friction under elastic contact conditions was considerably lower than under conditions that produced plastic contacts.

Miyoshi, K.↗

Transverse thermal expansion of carbon fiber/epoxy matrix composites

Thermal expansion coefficients and moduli of elasticity have been determined experimentally for a series of epoxy-matrix composites reinforced with carbon and Kevlar fibers. It is found that in the transverse direction the difference between the properties of the fiber and the matrix is not as pronounced as in the longitudinal direction, where the composite properties are fiber-dominated. Therefore, the pattern of fiber packing tends to affect transverse composite properties. The transverse properties of the composites tested are examined from the standpoint of the concept of homogeneity defined as the variation of packing (or lack thereof) throughout a sample.

Helmer, J. F.↗

Development of Space Station strut design

Candidate Space Station struts exhibiting high stiffness (38-40 msi modulus of elasticity) were manufactured and experimentally evaluated. One and two inch diameter aluminum-clad evaluation specimens were manufactured using a unique dry fiber resin injection process. Preliminary tests were performed on strut elements having 80 percent high-modulus graphite epoxy and 20 percent aluminum. Performed tests included modulus of elasticity, thermal cycling, and coefficient of thermal expansion. The paper describes the design approach, including an analytical assessment of strut thermal deformation behavior. The major thrust of this paper is the manufacturing process which produces aluminum-clad struts with precisely controlled properties which can be fine-tuned after fabrication. An impact test and evaluation procedure for evaluating toughness is described.

Johnson, R. R.↗

Elevated temperature axial and torsional fatigue behavior of Haynes 188

The results of high-temperature axial and torsional low-cycle fatigue experiments performed on Haynes 188, a wrought cobalt-base superalloy, are reported. Fatigue tests were performed at 760 C in air on thin-walled tubular specimens at various ranges under strain control. Data are also presented for coefficient of thermal expansion, elastic modulus, and shear modulus at various temperatures from room to 1000 C, and monotonic and cyclic stress-strain curves in tension and in shear at 760 C. The data set is used to evaluate several multiaxial fatigue life models (most were originally developed for room temperature multiaxial life prediction) including von Mises equivalent strain range (ASME boiler and pressure vessel code), Manson-Halford, Modified Multiaxiality Factor (proposed here), Modified Smith-Watson-Topper, and Fatemi-Socie-Kurath. At von Mises equivalent strain ranges (the torsional strain range divided by the square root of 3, taking the Poisson's ratio to be 0.5), torsionally strained specimens lasted, on average, factors of 2 to 3 times longer than axially strained specimens. The Modified Multiaxiality Factor approach shows promise as a useful method of estimating torsional fatigue life from axial fatigue data at high temperatures. Several difficulties arose with the specimen geometry and extensometry used in these experiments. Cracking at extensometer probe indentations was a problem at smaller strain ranges. Also, as the largest axial and torsional strain range fatigue tests neared completion, a small amount of specimen buckling was observed.

Bonacuse, Peter J.↗

Elevated temperature axial and torsional fatigue behavior of Haynes 188

The results are reported for high-temperature axial and torsional low-cycle fatigue experiments performed at 760 C in air on thin-walled tubular specimens of Haynes 188, a wrought cobalt-based superalloy. Data are also presented for mean coefficient of thermal expansion, elastic modulus, and shear modulus at various temperatures from room to 1000 C, and monotonic and cyclic stress-strain curves in tension and in shear at 760 C. This data set is used to evaluate several multiaxial fatigue life models (most were originally developed for room temperature multiaxial life prediction) including von Mises equivalent strain range (ASME Boiler and Pressure Code), Manson-Halford, modified multiaxiality factor (proposed in this paper), modified Smith-Watson-Topper, and Fatemi-Socie-Kurath. At von Mises equivalent strain ranges (the torsional strain range divided by the square root of 3, taking the Poisson's ratio to be 0.5), torsionally strained specimens lasted, on average, factors of 2 to 3 times longer than axially strained specimens. The modified multiaxiality factor approach shows promise as a useful method of estimating torsional fatigue life from axial fatigue data at high temperatures. Several difficulties arose with the specimen geometry and extensometry used in these experiments. Cracking at extensometer probe indentations was a problem at smaller strain ranges. Also, as the largest axial and torsional strain range fatigue tests neared completion, a small amount of specimen buckling was observed.

Bonacuse, Peter J.↗

Computational Materials Research

Computational Materials aims to model and predict thermodynamic, mechanical, and transport properties of polymer matrix composites. This workshop, the second coordinated by NASA Langley, reports progress in measurements and modeling at a number of length scales: atomic, molecular, nano, and continuum. Assembled here are presentations on quantum calculations for force field development, molecular mechanics of interfaces, molecular weight effects on mechanical properties, molecular dynamics applied to poling of polymers for electrets, Monte Carlo simulation of aromatic thermoplastics, thermal pressure coefficients of liquids, ultrasonic elastic constants, group additivity predictions, bulk constitutive models, and viscoplasticity characterization.

Hinkley, Jeffrey A.↗